BOQ C - Structural and Finishing

8/11/2019 BOQ C - Structural and Finishing

1/13

Rate Amount

Item Description Quantity Unit incl. Vat Incl. Vat

Euro Euro

Bill no. 1

Demolition / Structural Alterations

Preambles

a en erers are a v se o v s e s e an

acquaint themselves with the surroundings and

take any measurements deem necessary as no

claims will be accepted due to lack of knowledge

of the site.

bTenderers are to ensure that during the course of

works the inconvenience to third parties should

be very minimal and special care should be taken

to existing surroundings.

cTenderers shall provide all materials, labour and

plant required to execute the relative works.

d Tenderers are informed that works on site may

be interrupted to allow for other works to be

undertaken by third parties.

e precaut onary measures s ou e ta en or

the whole works to be carried out in conformity

with the local national Health and Safety

Regulations. Any related fees to be borne by the

tenderer.

fAny disposal of demolished / unwanted material

should be dumped in an approved dumping site

and any related fees to be borne by the tenderer.

g a es are o nc u e or wor ng y an

including any double handling for removal or

providing of any materials, hoisting, lowering,

transporting and disposal.

hQuantities shall be measured net and no

openings shall be deucted. Rates are to include

for all the waste and straight / circular work.

c/f

BILL C - STRUCTURAL AND FINISHING

WORKS

BOQ C - Structural and Finishing (2) 1 of 13 20/06/12


2/13

Rate Amount


Euro Euro

b/f

i Rates for openings are to include for all the

necessary masonry works such as any

necessary joggle joints, perpendicular jambs, etc.

as required by trade and as approved by

architect.

1.01 Break up, remove, cart away and dispose of all

existing wall ceramic tiles including the removal of all

sanitary fittings, fixtures and ware. Load, cart away

and dipose of resultant material.

1.00 item

1.02

Disconnect and plug adequately both the direct /indirect water supply to premises. Take up, remove,

and dispose of all the plumbing and drainage

pipework system (either surface mounted and/or

embedded in walls / floors and including any holding

clips / brackets) other related fittings and fixtures.

Rate is also inclusive for all material is to be loaded,

carted away and disposed of.

1.00 item

1.03 Take down, remove, load, cart away and dipose of all

existing internal onlytimber, (single and / or double

leaf) doors, cupboards, high level timber skirting,glazed timber 'anti-porta' and all other apertures

and/or furniture. Material will become the property of

the tenderer.

1.00 item

1.04 Ditto but heavy duty single and/or double leaf metal

door.

2.00 no.

1.05Take down, remove, load, cart away and dispose of

all existing internal aluminium (single and / or doubleleaf) doors, cupboards, partition walls including

glazing and partition doors, venetion and vertical

blinds, metal railings and all other furniture. Material

will become the property of the tenderer. Item does

not include windows.

1.00 item

1.06 Ditto but timber/gypsum parition walls including

partition doors.

1.00 item

c/f



3/13

Rate Amount


Euro Euro

b/f

1.07 Take down, remove, load, cart away and dispose of

all existing suspended ceiling soffits. Rate is inclusive

of the removal of all framing, brackets and/or clipssoffit panels, etc.

1.00 item

1.08 Break up, remove, load, cart away and dispose of all

the existing (2 layers) of terrazzo / cement floor tiles,

including any timber flooring attached and any

surrounding skirting. Torba bed is to be left on site for

re-use but any buried unusable utilities are to be

removed.

752.04 sq.m

1.09Take down existing single skin walls up to 2 courses

below exsiting dpc level including any suspended

steel beams and breaking up of any concrete plinths.

Load, cart away and dispose of material.

50.00 sq.m

1.10 Adequately block up window on the external side with

single skin softstone (fair faced & 'Fuq il-Fil finish'),

neatly laid to match faade courses and pointed with

cement/lime mortar.

ref. w 8 1.00 no.

1.11 Ditto including also on the inner side.

ref. w 9 1.00 no.

1.12Block up existing door opening in single skin walls

(dims. n.e. 1.82m x 2.20m). Rate is to include for all

the necessary masonry works to start from

foundations (thus including any excavation,

foundation concrete and dpc layer) and to be made

flush to the existing walls from both sides.

ref dr.1; dr.3 dr.5; dr.6 4.00 no.

1.13 Ditto but in double skin wall.

ref dr.7 1.00 no.

1.14Form door opening in existing single skin softstone

wall, (dims n.e. 1.52m x 2.20m). Rate is to include for

the formation perpendicular jambs and the supply

and fixing of softsone lintols.

ref do.1; do.2; do.5; do.9; do.10; do.11; do.12; do.13. 9.00 no.

c/fBOQ C - Structural and Finishing (2) 3 of 13 20/06/12


4/13

Rate Amount

Item Description Quantity Unit incl. Vat Incl. VatEuro Euro

b/f

1.15 Ditto but in double skin wall

ref do.7 1.00 no.

1.16 Construct 175mm thick single skin walls, set and laidin gauged mortar. Rate is also to include fro any

excavation until rock is exposed, concrete strip

footing, dpc layer and wall bearing (mursalli) to

existing walls.

170.00 sq.m

1.17Form door opening n.e. 1000mm wide from existing

dor opening n.e. 1600mm wide in single skin wall.

ref do.7; do.8 2.00 no.

1.18Form door opening n.e. 1000mm wide from existing

dor opening n.e. 1200mm wide in single skin wall.

ref do.6 1.00 no.

1.19

Scrape off existing deteriorated / spalling, concrete /

plaster, expose reinforcement and prepare patch for

curing. Sand down reinforcement, clean area and

apply approved rust inhibitor to reinforcement and

approved mortar to cover up patch as directed and to

the approval of the architect in charge.

75.00 sq.m

1.20 Carefully take down and remove any deteriorated

softstone blocks from walls and replace by new and

accordingly cut to size softstone blocks with gauged

mortar.

30.00 sq.m

1.21

Take up and/or repair and/or patch up exsiting

deteriorated waterproofing membrane by new torchwelded 3.5mm thick water proofing membrane.

10.00 sq.m

Bill no. 1

Demolition / Structural Alterations Works c/f to summary



5/13

Rate Amount


Euro Euro

Bill no. 2

Tiling, Sanitary Ware and Marble Works

Preambles

aAll works shall be measured net as laid. Rates

are to include for all waste, straight or raked

cutting, any pattern, fixing with sand / cement

(1:3) mortar and grouting of joints with approved

coloured grouting material.

b For wall tiling, rates are to include for the

necessary hacking of walls as and where

necessary.

c Colour and / or pattern, if any, of wall tiles is tobe decided by architect in charge.

d Supply and fixing of fixtures and other fittings.

Colour to match the wall or floor tiling or as

approved by architect in charge.

eAll sanitary fixtures are deemed to be including

all the necessary 32 / 50 /110mm diameter pvc

drain pipes connections, fittings, ironmongery

and any chasing in wall for foul water run off

from fixture to the drainage system,.

2.01 Supply, spread and level bed of 10 mm

chippings/sand 75mm (average) thick, over existing

torba or as where required to make up levels to

receive floor tiles. Rate is also inclusive for the

provision and fixing of pvc damp proofing fixed to

perimeter walls to eliminate dampness due to any

new finished floor levels.

752.04 sq.m

2.02 Supply and lay in cement and sand mortar, gress

ceramic floor tiles, semi matt and non slip as perspecifications, dims 600mm x 600mm for internal

use. Rate also includes for the grouting of joints with

approved material.

752.04 sq.m

2.03Glazed ceramic wall tiles, as per specifications, dims

600mm x 300mm. Rate is also inclusive for the

supply and fix of pvc edging finishing strips.

130.00 sq.m

c/f



6/13

Rate Amount


Euro Euro

b/f

2.04

Vitreous china wash hand lavatory basin (without

column) fixed with pair of brackets, waste fittings andchain, a pair of chrome pillar cocks for hot and cold

water supply, 30mm diameter plastic bottle trap, 2no.

Chrome plated angle valves and flexible connectors.

7.00 no.

2.05Vitreous china low level water closets complete with

a heavy duty plastic cover and push button flushing

cistern (cistern to be fixed behind wall), chrome

plated angle valve complete with flexible connector.

5.00 no.

2.06 Complete vitreaous china set for handicap use

including wash hand basin, water closet with flushing

water cistern and grab rails and all relative angle

valves, connectors, etc.

2.00 no.

2.07 Vitreous china Toilet roll holder (recessed type).

7.00 no.

2.08 Ditto but soap holders.

7.00 no.

2.09 Ditto but towel rails.

7.00 no.

Bill no. 2

Tiling, Sanitary Ware and Marble Works c/f to summary



7/13

Rate Amount


Euro Euro

Bill no. 3

Plastering and Decorating Works

a No openings whatsoever will be deducted for the

purpose of measurements.

b Rendering to window cills, lintels and jambs are

to be included in the works.

3.01 Strip off / sand down and remove existing wall

painting/finishes until original softstone surface is

exposed.

2,507.78 sq.m

3.02 Hacking of walls as and where necessary prior to any

rendering / plastering keying.

100.00 sq.m

3.03 Clean down, scrape where required, rake out joints

and point with lime / cement mortar surface of walls,

internally.

2,507.78 sq.m

3.04

Rendering in gypsum plaster 10mm thick, starting

with a base coat and finished by a top coat in white

gypsum plaster obtaining a straight and level finishsurface on horizontal and verical planes including the

provision and fixing of aluminium angle beads

around openings and/or wall edges.

350.00 sq.m

3.05 Prepare surfaces and apply two finishing coats of

approved emulsion paint, to wall surfaces including

gypsum partition surfaces. Colours to be approved by

architect in charge.

2,957.78 sq.m

3.06Supply 600mm x 600mm mineral fibre tagular type

suspended ceiling with white in colour exposed fixed

in position with approved hangers at 1.20m intervals

and all necessary and relevant ironmongery.

Lighting fixtures are not included.

500.00 sq.m

c/fBOQ C - Structural and Finishing (2) 7 of 13 20/06/12


8/13

Rate Amount


Euro Euro

b/f

3.07 Provide and fix gypsum boards suspended false

ceiling, including all necessary framing, fixing,

brackets and ironmongery all as approved byarchitect in charge. Lighting fixtures are not

included.

50.00 sq.m

3.08 Provide and instal 100mm thick gypsum partition

wall, mounted and fixed on galvanized steel support

frame including rock wool infill and min 16mm thick

gypsum boards on both sides.

20.00 sq.m

3.09Ditto but inclufing fire proof proof material.

28.00 sq.m

3.10Provide and instal 150mm thick gypsum partition

wall, mounted and fixed on galvanized steel support

frame including rock wool infill and min 2 no. 16mm

thick gypsum boards on both sides.

7.70 sq.m

3.11

Extra over item 3.10 for the supply and fixing of

single leaf door (dims. n.e. 1000mm x 2120mm).

1.00 no.

Bill no. 3 - Plastering and Decorating Works

Carried to Summary



9/13

Rate Amount


Euro Euro

Bill no. 4

Aluminium, Timber and Metal Works

a Rates for aluminium works are to include for

manufacture, fixing, sections to be dark green in

colour to match existing aluminium sections. All

doors and windows are to include double galzing

(otherwise as indicated), all necessary fittings

and the sealing with approved mastic material

both internally and externally.

b ates or nterna o nery are to nc u e or t e

manufacture and fixing of solid, laminated

surfaces flush doors inclusive of all necessary

frames / lining / architraves and glazing if andwhere necessary.

cRates for metal works are to include for hot dip

galvanizing, 2 coats of calcium plumbate paint

and all the necessary ironmongery.

dSizes stated in bill of quantities are only

indicative and tenderer is responsible for taking

physical measurements of all openings on site.

4.01 Aluminium, window with fixed lower part and top

hinged outwards including single glazed obscurred

glass. (approx. dims.0.60m x 0.80m)

7.00 no.

4.02 Timber, single leaf internal flush doors. (approx.

dims. n.e. 1.20m x 2.5m).

21.00 no.

4.03 Extra over previous item for the supply and fixing of

electric locks. 3.00 no.

4.04 Ditto but double leaf internal flush doors. (approx.

dims. n.e. 2.00m x 2.5m).

7 no.

4.05 Ditto but fire doors and including magnet hold open

position. Tenderer is to provide an official

certification.

2 no.

c/f



10/13

Rate Amount

Item Description Quantity Unit incl. Vat Incl. VatEuro Euro

b/f

4.06Maintenace to existing 2 leaf timber main entrance

door. Strip off existing paint, repair timber where and

as required, apply 1 undercoat and 2 coats gloss oilpaint, replace any existing defective ironmongery with

new. Rate is to apply for both sides of the door.

(approx. dims. n.e. 2.50m x 3.00m).

1 no.

4.07Maintenace to existing 2 leaf metal main entrance

door. Sand down existing paint, repair where and as

required, apply 1 undercoat and 2 coats gloss oil

paint, replace any existing defective ironmongery with

new. Rate is to apply for both sides of the door.

(approx. dims. n.e. 1.80m x 3.00m).1 no.

Bill no. 4 Aluminium, Timber and Metal Works

Total carried to Summary



11/13

Rate Amount


Euro Euro

Bill no. 5

Plumbing Works

Preambles

aAll items in this bill are subject to measurement.

b Supply, install, test and commission the

following.

5.01 Provide and instal approved type upvc plumbing

pipes including relative fittings for both cold and hot

water plumbing system. Rate is inclusive for all the

necessary bracketing, supports, chasing in walls and

well clipped pipework. Chases shall also be madegood in 1:3 cement/sand mortar.

a 16mm diameter 100.00 m

b 22mm diameter 50.00 m

5.02 Connect water supply of new plumbing system with

existing. Rate is inclusive of all the necessary fittings,

gate valves, reducers, etc. to provide an efficient

water supply.

1.00 no.

5.03 Testing and commissioning of complete system1.00 no.

5.04 Provide one set negatives and two sets of prints of as

fitted drawings

1.00 no.

Bill no. 5 Plumbing Works




12/13

Rate Amount


Euro Euro

Bill no. 6 - Drainage Works

Preambles

a Pipes shall be measured in metres over all

fittings and branches.

bFittings shall be enumerated and given as extra

over the pipe in which they occur. Joints in the

running length should be deemed to be included.

c All builders' work, connection to existing

drainage mains and testing and commissioning

shall be deemed to be included.

d Inspection chamber manholes shall include for

all necessary excavation, connecting up and

shall be enumerated.

6.01 Excavate trenches in any type of material to

accommodate upvc pipes (measured separately) to

the required levels, load, cart away and dispose of

material.

22.50 cu.m

6.02 Provide and cast concrete grade C.25 to bed and

square surround to 110mm diameter pipes.

10.13 cu.m

6.03 Provide, lay and align heavy duty 110mm diameter

uPVC pipes in trenches as directed inclusive of all

necessary fittings (e.g. bends, gulleys, hoppers, y's,

etc.)

65.00 m

6.04 Provide and fix heavy duty 600mm x 600mm

manhole including cover lids including all necessary

concrete grade C20 bedding and surround.

4.00 no.

Bill no. 6 - Drainage Works




13/13

BILL C - GENERAL SUMMARY

Tender for Civil / Repair Works and Finishings at the Evans Building, Lower Level, Valletta.

1.00 Bill no. 1

Demolition / Structural Alterations Works

2.00 Bill no. 2

Tiling And Sanitary Ware

3.00 Bill no. 3

Plastering and Decorating Works

4.00 Bill no. 4

Aluminium, Timber and Metal Works

5.00 Bill no. 5

Plumbing Works

6.00 Bill no. 6

Drainage Works

Grand Total


Documents

BOQ C - Structural and Finishing