Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Big Challenges: Real Solutions
Process Solutions Summit
Room 1 Room 2 Room 3 Room 4 Room 6 Room 7 Room 8
Lunch from 12:00-1:30 pm
Schedule for September 21st & 22nd – Registration opens at 7:00am
Thur. 8:30-10:00am
Wed. 8:30-10:00amWed. & Thur. 8:30-10:00am
Wed. & Thur. 8:30-9:30am
Wed. & Thur. 9:45-10:45am
Wed. & Thur. 11:00am-12:00pm
Wed. & Thur. 1:30-2:30pm
Wed. & Thur. 1:30-3:00pm Wed. & Thur. 1:30-3:00pm
Wed 1:30-3:00pm
Wed. & Thur. 2:45-3:45pm Thur. 1:30-3:00pm
Hands-On Workshops
Viking Internal Gear Pump Workshop
(Wed. Only)
Hands-On Workshops
The Fastest Field pH Calibration Ever –
Guaranteed
Hands-On Workshops
Pulsafeeder External Gear Pump Workshop
(Thur. Only)
Hands-On Workshops
The Secret to Becoming a Process Equipment Genius
Live Demo
Top 10 Ways to Kill Your Pump Dead
Radar Steps Into New Dimensions – A
Low Cost Radar Instrument with Bluetooth Set Up
Calibration Compliance
Resistance is Futile!
Overfill Prevention – Protect Lives, the
Environment and Avoid Costly Fines via
Functional Safety
Use all the Tools in the Tool Box
Introducing The Pepperl+Fuchs
Bullet – Best in It’s Class Wireless HART
Adapter
Advanced Power Control Techniques to
Reduce the Burden on Your Process and Your Wallet
Wireless Design Considerations for Industrial Applications
Process Safety Standards part 1 – What are they and what do they mean
to me?
Process Safety Standards Part II - How Do We Meet The Standards?
Practical Applications of
Wireless Solutions
Monitoring the Health of Valves and
Valve Automation Systems
Flotronic Pumps - A Whole New Way
of Looking at Air Operated Diaphragm Pumps for Sanitary
and Hygienic Applications
Industrial Generation: Wages, Key Performance
Indicators and Optimization of
Boiler/Steam Systems (Wed. Only)
Hands-On Workshops
The Secret to Becoming a Process Equipment Genius
Hands-On Workshops
Air Operated Pump Disassembly and Rebuild Workshop
(Wed. Only)
Hands-On Workshops
Vertical Turbine Pump Workshop
(Thur. Only)
Hands-On Workshops
The Coriolis Mass Flow Meter – What Makes It Tick, What
Makes It Sick
Hands-On Workshops
Replace Differential Pressure Sensors in
30 Minutes
Hands-On Workshops
PlantPAx Integrated Workshop
Industrial Networks Cybersecurity
Threats
Can you Speak IT? Ethernet Process
Control 101
Integrated Pump Monitoring –
Leveraging Process & Motor Control
Technology
Live Demo
What is the Weakest Link?
Thur. 1:30-2:30 pm
Thur. 2:45-3:45pm
Wed. & Thur. 1:30-3:30 pm
Regulatory & Environmental
Pressures in Power Generation Meeting
the Challenges... (Thur. Only)
Understanding the Importance of
Thermal Management (Thur. Only)
Energy Optimization in Pumps and
Pumping Systems
Live Demo
Steam Trap Testing and Monitoring
Wed. 2:45-3:45pm
The Do’s and Do Not’s of Operating Pumps
on VFD’s (Wed. Only)
• World-class capabilities of each
participating company
• Hands-on experience in numerous labs
• Technical knowledge gained in forums
• Professional Development hours awarded
• Live demonstrations each day
• Various product and solution
exhibits on display
New for 2016 – Carotek will host several New Hands-On Workshops:
1) Instrumentation Verification & Set-up - Participate in hands-on workshops for pH calibration, Coriolis Mass meters, Radar Instrumentation Bluetooth set-up, replace dP sensors and more to hit the highlights.
2) Back by Popular demand - Pump disassembly and reassembly. Teams of 4-8 class participants will work together to tear down and rebuild multiple pump technologies – internal gear, AODD, external gear/diaphragm metering and centrifugal.
3) Live Demos – What is the Weakest Link? Witness Control Valve Benchmark Testing & Report Generating. “How to Kill Your Pump”. View a live demonstration of Steam Trap Operation and the critical role they play in efficiency of your steam system operation. Experience our Calibration Rig showing the advantages of calibration management using automated calibration tools and software like FieldExpert and Fluke process calibrators.
Evening Reception
Join us as we celebrate “Under the Big Top, the greatest customers on earth.” It will be an evening full of good times, good food, good music and great friends. We will give away exciting door prizes from IPADS and Flat Screen TV’s to Richard Petty Driving Experiences and Nascar Fun. You must be in attendance for a chance to win. The event begins at 4:30 Wednesday, September 21st.
What you’ll get out of the experience:
Register Now at www.carotek.com/pss
Process Solutions SummitYou Are Invited
Attend the Process Solutions Summit held at the Carotek facility
in Matthews, North Carolina. This unique event will provide an
environment where you can exchange innovative ideas, learn best
practices and seek solutions with your process automation peers.
You will learn from subject matter experts as you introduce yourself
to innovative solutions for Pumps, Valves, Steam, Process Control and
Instrumentation. Admission is FREE but we would like you to bring a non-perishable food item. We will donate all items collected to a local food pantry to help those in need.
1
Wednesday (Only) 8:30-10:00 Hands-On Pump Workshops - CT101 - Viking Internal Gear Pump Viking Pump | Room 8
Hands-On Gear Pump disassembly and rebuild. You and your colleagues will have your own work station, factory built pump
and the tools you will need for a complete Gear pump disassembly and re-build. You will see and touch the components
that make up an Internal Gear Pump, perform a disassembly and rebuild in 90 minutes. You will have a trainer and service
technicians available to help you through this hands-on educational process. You will learn about wear points in a gear
pump and what to look for in wear patterns to find the root cause of a gear pump failure. You will learn about factory
tolerances and how to measure tolerance in your pump to determine necessary parts replacement. This class is suitable
for all attendees to the PSS. From entry level to corporate executive this is your chance to learn about how an Internal Gear
Pump works. Take this opportunity to learn more about a total process system and how you can increase your uptime
performance in the workplace. At the end of the class you will receive a certification of completion of this
Pump Analysis Class.
Thursday (Only) 8:30-10:00 Hands-On Pump Workshop - CT103 - Pulsafeeder External Gear Pump Pulsafeeder | Room 8
Hands-on External Gear Pump and Diaphragm Metering Pump disassembly and rebuild. This is a small class where you and
your colleagues will work together to tear down and rebuild a Pulsafeeder External Gear Pump and a Diaphragm Metering
Pump. Learn how fast and simple it is to rebuild this unique External gear pump designed for corrosive chemical, acid and
caustic service. Some of these pumps will fit in the palm of your hand. Your team will have your own work bench, the pump
and the tools to complete the disassembly and rebuild to factory specifications. In the end we will bet that you can rebuild
this pump with your eyes closed! This a chance for everyone to learn how these pumps work. E&I, Maintenance, Engineering
and Team Leaders can all learn from this class. You will receive a certificate of completion for this class at the end of this 90
minute session.
Wednesday & Thursday 8:30-10:00 Hands-On Instrumentation Workshop - CT113 - The Fastest Field pH Calibration Ever-Guaranteed! Endress+Hauser | Room 1
This hands on experience will explore the fundamentals to achieve the most reliable pH calibrations while spending less
time in the plant. Techniques learned here will yield increased pH sensor uptime. The class is perfect for pH novices as well
as the PhD’s of pH. Also covered will be a review of some typical pH gotchas.
Live Demo - CT114 - What is the Weakest Link?DeZurik | Room 6
The control valve is typically the only component in a process loop that actually moves to adjust the process. How they are
sized, their ability to respond to signal changes and providing a predictable output over a wide range of signal changes has
a significant impact on plant efficiency and profitability. In this session we will look at three factors critical to control valves;
sizing, performance and installed gain. You will also witness “Benchmark®” testing and report generation.
2
Wednesday & Thursday 8:30-9:30CT112 - Radar Steps Into New Dimensions - A Low Cost Radar Instrument with Bluetooth Set Up Endress+Hauser | Room 2
Bring your phone because in this session that will be the only tool you need to set up this new radar devise. You’ll not only
see how simple set up is via Bluetooth, but you’ll also see echo curves from the device on your phone.
CT124 - Process Safety Standards Part I - What are they and what do they mean to me? Rockwell | Room 4
This session is an introduction into Process Safety standards in North America and how we got where we are today and
how they impact End Users. There are legal requirements, there are codes that need to be met and then there are standards
that are designed help with compliance, although they are not always viewed that way.
CT126 - Industrial Networks Cybersecurity Threats Rockwell | Room 7
As industrial organizations move towards greater visibility within their operations, the need to establish a seamless flow
of information by connecting control systems to the enterprise has become a requirement of modern industrial networks.
Effectively developing a fully connected enterprise requires a comprehensive approach to industrial security that extends
beyond the control system to include policies and procedures that address people, process and technology-related risks.
A complex, interconnected system doesn’t come without challenges. It’s critical to understand the potential risks and start
building security into your industrial automation control systems.
CT116 - Introducing the Pepperl+Fuchs Bullet -”Best in its Class WirelessHART Adapter” Pepprerl&Fuchs | Room 3
WirelessHART provides the infrastructure to add a new measurement to your control system that is simple, reliable and
secure. During this session, we will review the many connectivity options available today, and introduce the most versatile
WirelessHART Adapter “The BULLET” that has more features than all the other products available on the market combined.
With the best safety ratings, StepVolt Technology and the ability to Multidrop up to 8 HART Devices, the Bullet is the one
adapter that will meet all your application needs.
3
Wednesday & Thursday 9:45-10:45 Hands-On Instrumentation Workshop - CT105 - The Secret to Becoming a Process Equipment Genius Carotek | Room 8
Experience the “PTU®”, Process Training Unit. A Mini working process plant with 95+ field instruments. Participate in hands-
on labs to set-up and verify different process technologies for level, flow, pressure and temperature instruments.
CT121 - Calibration Compliance - Resistance is Futile! Endress+Hauser | Room 2
What is calibration? Review automated calibration tools and software that help you remain in calibration compliance.
We will discuss the struggles and issues you face in remaining compliant. We will witness a demonstration of on-site
calibration capabilities using the calibration rig.
CT125 - Process Safety Standards Part II – How do we meet the standards?Rockwell | Room 4
This session is a more focused look at ISA84.00.01 (IEC61511) and what it takes to comply with this standard. Complying with
the standard is not as bad as it first seems, because it requires a different approach than most End Users are used to. The
standard is written largely by end users, but some are so used to doing everything themselves ‘as they go’, they cannot
possibly comply with it. If End Users focus on defining what they actually need, then use competent and qualified vendors,
they can comply and dramatically improve Safety.
CT127 - Can You Speak IT? Ethernet for Process Control 101Rockwell | Room 7
The prevalence of Ethernet devices in manufacturing requires process control professionals to educate themselves on
the fundamentals of information technology. Attendees will learn the basics of Ethernet and Rockwell Automation-Cisco
recommended best practices for deploying Ethernet for process control. Both process control and information technology
professionals are encouraged to attend. Bring your IT buddy!
CT120 - Advanced Power Control Techniques to reduce the Burden on Your Process and Your WalletEurotherm | Room 3
A growing number of processes in the industrial sector rely heavily on electrical heating applications for process heat
control. Often, these processes require manufacturers to control multiple loads with similar thermal characteristics, all
driving/demanding power at the same time. This power demand overlap often drives the power grid load demand to quite
high levels resulting in stress on the power network. In many areas, this peak power demand is also a critical factor in the
cost that the end users have to pay for their electrical energy. Our lecture will explain in detail how load management, load
shedding, and advanced power factor correction techniques can lessen the burden of stress and wear/tear on your process
while offering substantial cost savings.”
4
Wednesday & Thursday 11:00-12:00 Live Demo - CT106 - Top 10 Ways to Kill Your Pump Dead!Viking Pump | Room 8
See a working pump module and watch as we subject it to all the things you can do wrong in a pump system. We will
demonstrate first hand some of the common problems in a pump system that can kill your pump. Here are the situations
and topics we will cover in this live demo. 1-Skip the strainer - We will show pumps that have been destroyed by foreign
objects that entered the suction of the pump. 2- Starve the Pump- We will demonstrate common suction problems and how
it affects pump performance. 3- Over-speed the pump - demonstrate the fluid dynamics when you run the pump too fast.
4- Over-pressure the pump - see how common discharge restrictions over pressurize and reduce the life of the pump. 5-Run
to Failure-see how you can monitor your pump to indicate upset conditions and shut the pump down before catastrophic
failures. 6-Deadhead the Pump - illustrate common discharge problems that can deadhead a pump. We will show wear
patterns that indicate deadhead and over-pressure. 7- Install the Pump poorly-severe misalignment, excessive flange
loading, and pipe stress can severely damage your pump. 8-Change the service without consulting your pump expert -
examples include pumping thicker, more corrosive, less lubricating or abrasive fluids without consideration for the current
pump construction. 9-Run relief valve in full bypass - relief valves are there to protect your pump and are not to be used as
full bypass valves. 10- Skip preventive maintenance - regreasing bearings, changing gear box oil, and replacing worn parts
will all extend the life and performance of your pump. Overall you will learn how pump failures are more often a symptom
of a pump system problem and not a fault of the pump.
CT115 - Use all the Tools in the Tool BoxK-Patents | Room 1
Utilizing K-Patents unique and accurate in-line Brix measurement for concentration provides greater flexibility for control
than other more traditional instrumentation measurements. Refractive index provides no calibration, drift free, proven
measurement.
CT111 - Overfill Protection- Protect Lives, the Environment and Avoid Costly Fines via Functional SafetyEndress+Hauser | Room 2
This session will answer the following questions: How does a level instrument fit into an SIS? What is SIL? What is proof
testing and why is it required? What are the options for proof testing? What is in situ proof testing? What role is the
government playing in process safety?
5
Wednesday & Thursday 11:00-12:00CT108 - Monitoring the Health of Valves and Valve Automation SystemsFlowserve | Room 6
Have you ever experienced an unplanned maintenance activities and/or equipment failure?? Reduction in this costly
events is an emphasis for every manufacturer in the process control industries, especially with regards to improving
safety and profitability. Wouldn’t it be great to have an “advanced warning” of impending reliability issues and product
failures? This informative session will assist you in meeting these objectives by minimizing outages and optimizing
efficiencies. Leave with the ability to identify the engineering best practices for improving process control, implementing
“smart” valve diagnostics and reliable operation of safety-critical valve applications. We will briefly review the various
partial stroke testing (PST) conventions, from inexpensive mechanical devices to the more robust PST solutions enabling
valve and actuator diagnostics via digital communications. Understanding the requirements and capabilities of these valve
automation systems will increase the reliability and service life of process control valves and safety-critical ESD systems.
CT122 - Practical Application of Wireless SolutionsIndustry Experts | Room 4
This session will focus on the application of Propriety, Hart and ISA100 wireless technology in plant settings. The format
will be an open forum discussion with industry experts concerning the pluses and minuses of the various topologies
and practical application of each. Applications including steam trap monitoring, vibration monitoring, temperature
measurement, safety valve monitoring and other process signal measurement will be discussed.
CT128 - Integrated Pump Monitoring - Leveraging Process and Motor Control Technology to Monitor & Extend Mechanical Equipment LifeRockwell | Room 7
Leverage the capabilities of the Logix control platform combined with the Intelligent Motor Control portfolio, intuitive
software and EtherNet/IP network to help improve productivity and reliability of your motors. See how technology
advancements in process and motor control technology can monitor critical characteristics and detect common problems
to help extend equipment life and reduce ongoing operational expenses. This presentation will be focused on pumps.
CT129 - Wireless Design Considerations for Industrial ApplicationsRockwell | Room 3
Industrial Automation and Control System (IACS) applications increasingly use wireless LANs that require reliable data
transmission with low levels of latency and jitter. Deploying a wireless network requires thoughtful planning and design, as
well as periodic monitoring to meet expectations for bandwidth, throughput, reliability and security.
6
Wednesday Only 1:30-3:00 Hands-On Pump Workshop - CT102 - Air Operated Pump Disassembly and Re-buildWarren-Rupp | Room 8
Hands-on Pump disassembly and rebuild. This is a small class where you and your colleagues will work together to tear
down and rebuild an Air Operated Double Diaphragm pump. Your team will have your own work bench, the pump and
the tools to complete the task. This class is suited for everyone from Maintenance to Engineering to Purchasing and
Management. You’ll learn about the components of this pump and how it works. You’ll learn how to identify wear points,
root cause failure and what you can do to prolong the life of your pump. Once you’re finished we’ll put air to the pump and
operate it to see how well you performed the Pump rebuild. At the end of the class you will receive certification of your
Pump Maintenance training session to take with you. For an hour and a half of your time you can’t afford to miss this Hands-
On educational session
Thursday Only 1:30-3:00 Hands-On Pump Workshop - CT104 - Vertical Turbine PumpPeerless Pump | Room 8
Hands-On disassembly of a Vertical Turbine Column and bowl assembly. There will be shop bench stations with a Vertical
Turbine bowl assembly for each group to learn how to disassemble and re-build a Vertical Turbine pump wet-end. Proper
tools and parts will be available for each assembly so each team can experience first-hand the process for Vertical Turbine
repairs. A seasoned Vertical Turbine Field Service Engineer from Peerless Pump will teach the class and offer insider tips
for this process. You will learn what to look for in wear of the components as you disassemble the pump to assess root
cause of pump failures. This is a unique opportunity to learn the inner workings of Vertical Turbine pumps with a seasoned
professional. Don’t miss this opportunity to learn about this commonly used pump.
Wednesday & Thursday 1:30-3:30 Live Demo - CT107 - Steam Trap Testing and MonitoringArmstrong/Carotek | Room 3
Steam Traps play a critical role in efficient steam system operation. Traps that fail can pose serious efficiency, operational,
and safety concerns. Therefore, it is important to understand how different traps fail, how to identify failed traps, and how
to monitor and manage steam trap performance to keep system efficiency high and reduce safety concerns. This session
will include a live demonstration with ultrasonic and thermal imaging devices.
Wednesday & Thursday 1:30-3:00 Hands-On Instrumentation Workshop - CT117 - The Coriolis Mass Flow Meter-What Makes It Tick,
What Makes it SickEndress+Hauser | Room1
A look under the hood of the fastest growing technology in the global flow meter market, to find out how the Coriolis
meter really works, what process conditions can cause upset and why, and what leading edge technology for
diagnostics and verification can do to help. A live “hands on” verification will demonstrate the ease and completeness of
traceable verification.
7
Wednesday & Thursday 1:30-3:00 Hands-On Instrumentation Workshop - CT109 - Replace Differential Pressure Sensors in
30 Minutes or LessEndress+Hauser | Room 2
An overview of the latest Electronic Differential Pressure devices used for Level measurement. Explore traditional system
pitfalls and short comings of existing capillary/diaphragm seals or impulse tubed systems and how to quickly replace them
with an Electronic Differential Pressure system for more reliable and maintenance free performance. Hands-on lab to learn
how to wire new sensor connections and the assigning of 4-20mA for the LRV & URV.
Hands-On Workshop - CT130 - PlantPAx Integrator WorkshopRockwell | Room 7
This session will define what PlantPAx is. We will discuss selecting and sizing the common core components of the
architecture such as controllers, IO, and application servers. Review infrastructure design options and tools such as
virtualization and networks. Finally, we will build an example application from the work completed in the sizing procedure
and discuss system validation practices. This session is recommended for those that have roles or responsibilities for
engineering and/or designing DCS systems.
Wednesday & Thursday 1:30-2:30 Hands-On Instrumentation Workshop - CT105 - The Secret to Becoming a Process
Equipment GeniusCarotek | Room 8
Experience the “PTU®”, Process Training Unit. A Mini working process plant with 95+ field instruments. Participate in hands-
on labs to set-up and verify different process technologies for level, flow, pressure and temperature instruments.
CT119 - Flotronic Pumps – a whole new way of looking at Air Operated Diaphragm Pumps for Sanitary and Hygienic applications.Flotronic Pump – Room 6
Do you want to CIP your diaphragm pumps in line? Do you want to completely self-drain your pump? Do you want to pump
nasty chemicals in a full PTFE pump with mobile rupture protection and detection? How about dramatically cutting your
maintenance / inspection times? We will demonstrate the ‘One Nut’ Air Operated Diaphragm Pump and show you a range of
pumps that can dramatically improve down time, save product waste and give you all new levels of hygiene and operator
protection!
Wednesday Only 1:30-2:30 CT131 - Industrial Generation: WAGES, Key Performance Indicators and Optimization of Boiler/Steam SystemsRockwell | Room 4
This presentation will cover WAGES (Water, Compressed Air, Gas, Electric, Steam), KPIs for boiler/steam systems, and
monitoring these KPIs with proven measurement techniques. Learn best practices for Industrial Energy and CHP and how
to identify opportunities for industrial boiler performance improvement.
8
Thursday Only 1:30-2:30CT132 - Regulatory and Environmental Pressures in Power Generation: Meeting the Challenges of an Uncertain EnvironmentRockwell | Room 4
The power generation industry in North America continues to face unprecedented challenges in the face of coal plant
retirements in order to meet the needs of its consumers – increased regulations (e.g. Clean Water Act 316B, CPP, ELG, CCR),
aging plants/assets, and profitability pressures. Join this session for an overview of industry trends, impact on utility and
industrial plants who are large electrical power consumers and water users, and learn how Rockwell Automation is helping
customers reduce the operating costs and risk associated with obsolescence, security and aging facilities.
Wednesday & Thursday 2:45-3:45 CT118 - Energy Optimization in Pumps and Pumping SystemsGrundfos | Room 4
Pumps consume more than 10% of the world’s electricity, but too much of it is wasted because of oversized or inefficient
pumps. Learn about saving energy and money on your current pumping systems from Grundfos’ Energy Optimization
experts. In this class you will learn about: Wire-to-water efficiency, pump curves and best efficiency, actual versus
apparent pressure, single versus multi-stage pumping, and staging on efficiency. Included in this presentation will be
tangible examples of “why to right size” the system and the impact on the life of the pump. Specific cases in optimizing
Pressure Boosting systems will impress participants with Grundfos’ technical ability and energy savings potential. You will
learn about the Grundfos Energy Optimization process and the tools that Grundfos personnel use to support this initiative.
Whether you need a refresher or are new to this topic, there is something for you in this class.
Wednesday Only 2:45-3:45CT123-The Do’s and Do Not’s of Operating Pumps on VFD’sCharles R. Underwood Inc. | Room 6
Learn the key points to identify if your pump application is suitable for a VFD. Is your motor ready for your VFD application?
Discuss how to identify problems with your Pump/VFD application. Is the problem the pump, the VFD or the application?
Should you have a different pump life expectation when using a VFD? See real cause and effects of improperly operating
your pump with a VFD.
Thursday Only 2:45-3:45CT110 - Understanding the Importance of Thermal ManagementPfannenberg | Room 6
Proper thermal management is critical to the health of your electronics. This session will walk you through choosing
the correct thermal management solution for application. Learn how to reduce downtime, save money on electronics
replacement and new efficient techniques to reduce energy cost .
9
PO Box 1395700 Sam Newell RoadMatthews, NC 28106 704-844-1100
For additional information, please visit: carotek.com
North Carolina • South Carolina • Virginia • Georgia • Tennessee
NCSC
GA
TN
VA
PDH Credits
1 PDH Credit per attended session. Certificates
will be sent via email after the event.
SPECIAL ATTRACTIONS:
Process Training Unit
Test your knowledge and skill in our PTU
Challenge by registering for the class “The
Secret to Becoming a Process Equipment
Genius”. At the end of the class your name
will be entered to win one of the top prizes
designated just for PTU Challenge Participants.
Facility Tours
Take a tour through the Carotek Mechanical
and Electrical Integration Shops. Learn
about Carotek’s capabilities of designing and
manufacturing modular process equipment
skids and electrical control panels all under
one roof. The tour concludes with a look at the
Carotek Valve automation shop, where you can
watch valve automation in real time.
Hotels
1) Comfort Inn (1.5 miles from Carotek)
704-845-5911
$72/night includes Hot Buffet Breakfast
comfortinn.com
2) Courtyard Marriott (3.4 miles from Carotek)
704-846-4466
$109/night Included Buffet Breakfast
cwp.marriott.com/cltcm/carotek
3) Holiday Inn Express (1.3 miles from Carotek)
704-443-3100
$119/night- Complimentary Breakfast
4) Hampton Inn (1 mile from Carotek)
704-841-1155
$99/night Complimentary Breakfast
Shuttle service available from hotels
to/from the event.
Venue Map
Register Online/Maps & Directions at http://www.carotek.com/pss
Charging Station
Lawn Area
Stairs to Room 1 & 2
Phone Zone
Entrance
Room 3
Room 6
Room 7
Room 8
SHOP AREAAREASHHOP
Registration
To Activity Tent
Front Parking
Room 4
LEVEL TWO
LEVEL ONE
Room 1 Room 2