3
Copyright 1987-2018 State Supply www.StateSupply.com Toll Free: 800.772.2099 Order Online: www.StateSupply.com Fax: 651.774.7156 [email protected] 5 Bell & Gossett EcoCirc ® 19-16 Circulating Pumps High Efficient, EcoCirc ® 19-16 pumps have three different, selectable modes of operation: Proportional Pressure Mode (factory default): Sensorless control mode automatically adjusts pump performance to the re- quirements of the system, based on the curve that is set with the pump’s integral adjustable dial. Mode identified by lit “blue” light on adjustment dial. Constant Pressure Mode: Sensorless control mode automatically maintains constant differential pres- sure, based on the curve that is set with the pump’s integral adjustable dial. This mode is used on systems with relatively small pressure losses. This mode identified by the lit “green” light behind the speed adjustment dial. Constant Speed Mode: Pump maintains a fixed speed mode at any flow demand, based on the pump curve that is set with the pump’s integral adjustable dial. This mode identified by the lit “white” light behind the speed adjustment dial. Specifications: Motor Design: ECM - Electronically commutated shaft-less spherical motor with permanent magnet technology, Maximum system pressure: 150 psi; Maximum operating temp: 203° F; 115 volt, 60 Hertz power; Power con- sumption: 5 to 60 Watt; Water/Glycol mixtures to 20% volume. Step-less speed dial with LED for pump status and troubleshooting Magnetically centered spherical impeller/rotor *High Efficiency ECM Motor Model No. Product Code Body Construction Max. RPM Motor Pump-to-Pipe Flanges (Set of Two Flanges) Pump Weight in lbs. Pump Order No. Phase Watts ¾” 1” 1¼” 1½” 19-16 6050B2003 Cast Iron Variable 115V 1 ph 60 Hz Varies 4-60 8.25 BH1129E 6050B2004LF Stainless Steel BH1129H BG1005 BG1010 BG1015 BG1020 BG1040 BG1045 BG1050 BG1055 EZ replacement for your Series 100 pumps Same flange & connection as series 100 pumps, but uses less than one-half of the electricity and cost LESS than the 100 model pump. Ordering Guide EcoCirc ® reduces energy consumption by more than 60% Uses less than half the electricity as standard heating circulators! *ECM motors reduce energy consumption by at least 60% when compared to standard motors. Dimensions, inches 6.38 3.54 6.09 7.4 3.74 Cast Iron Model Stainless Steel Model Proportional Pressure Constant Pressure Constant Speed Replaced the short lived 19-14 series in Jan. 2018

Bell & Gossett EcoCirc 19-16 Circulating Pumps · Operational in 3 different standard control modes: Proportional pressure, constant pressure and constant speed. The night mode functionality

  • Upload
    others

  • View
    8

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Bell & Gossett EcoCirc 19-16 Circulating Pumps · Operational in 3 different standard control modes: Proportional pressure, constant pressure and constant speed. The night mode functionality

Copyright 1987-2018 State Supply www.StateSupply.com

Toll Free: 800.772.2099 ■ Order Online: www.StateSupply.com ■ Fax: 651.774.7156 ■ [email protected]

5

Bell & Gossett EcoCirc® 19-16 Circulating Pumps High Efficient, EcoCirc® 19-16 pumps have three different, selectable modes of operation: ■ Proportional Pressure Mode (factory default):

Sensorless control mode automatically adjusts pump performance to the re-quirements of the system, based on the curve that is set with the pump’s integral adjustable dial. Mode identified by lit “blue” light on adjustment dial.

■ Constant Pressure Mode: Sensorless control mode automatically maintains constant differential pres-sure, based on the curve that is set with the pump’s integral adjustable dial. This mode is used on systems with relatively small pressure losses. This mode identified by the lit “green” light behind the speed adjustment dial.

■ Constant Speed Mode: Pump maintains a fixed speed mode at any flow demand, based on the pump curve that is set with the pump’s integral adjustable dial. This mode identified by the lit “white” light behind the speed adjustment dial.

Specifications: Motor Design: ECM - Electronically commutated shaft-less spherical motor with permanent magnet technology, Maximum system pressure: 150 psi; Maximum operating temp: 203° F; 115 volt, 60 Hertz power; Power con-sumption: 5 to 60 Watt; Water/Glycol mixtures to 20% volume.

Step-less speed dial with LED for pump status and troubleshooting

Magnetically centered spherical impeller/rotor

*High Efficiency ECM Motor

Model No.

Product Code

Body Construction

Max. RPM

Motor Pump-to-Pipe Flanges (Set of Two Flanges) Pump

Weight in lbs.

Pump Order No. Phase Watts ¾” 1” 1¼” 1½”

19-16 6050B2003 Cast Iron

Variable 115V 1 ph 60 Hz

Varies 4-60 8.25

BH1129E

6050B2004LF Stainless Steel BH1129H

BG1005 BG1010 BG1015 BG1020

BG1040 BG1045 BG1050 BG1055

EZ replacement for your Series 100 pumps

Same flange & connection as series 100 pumps, but uses less than one-half of the electricity and cost LESS than the 100 model pump.

Ordering Guide

EcoCirc® reduces energy consumption by more than 60%

Uses less than half the electricity as standard heating circulators!

*ECM motors reduce energy consumption by at least 60% when compared to standard motors.

Dimensions, inches

6.38

3.54

6.09 7.4

3.74

Cast Iron Model

Stainless Steel Model

Proportional Pressure Constant Pressure Constant Speed

Replaced the short lived 19-14 series in Jan. 2018

Page 2: Bell & Gossett EcoCirc 19-16 Circulating Pumps · Operational in 3 different standard control modes: Proportional pressure, constant pressure and constant speed. The night mode functionality

Copyright 1987-2018 State Supply www.StateSupply.com

Toll Free: 800.772.2099 ■ Order Online: www.StateSupply.com ■ Fax: 651.774.7156 ■ [email protected]

9

Bell & Gossett e3 Whole House Potable Water Pumps Ecocirc e3 Pumps run on 10 watts - About the same power consumption as a night light Powered by ECM motor design that results in significant energy savings and improved performance: A permanent magnet motor eliminates the need for input power to mag-netize the rotor, thereby saving the majority of energy used to power a pump.

Adjustable speed switch models to manually adjust to infinite motor speeds.

Adjustable temperature models are only found on fixed speed only pump.

UltraCirc models a built-in air purger, and integral check/isolation valves.

■ Max. working temp: 203 F ■ Min. working temp: 50 F ■ Max. working pressure: 150 psi ■ Power consumption: 5-28 watts ■ Power source: 100-140V, 60HZ ■ Model e3-4 pumps up to 4 GPM ■ Model e3-6 pumps up to 6 GPM

e3 Timer

Can be installed on all e3 pumps

Easily installed to the bottom of any e3 pump. Uses the pump’s power. Three modes: ON-OFF-TIMER. 30 minute mini-mum run time. Order e3 Timer separately.

Pump Model No.

Product Code

Connection Power

Consumed Adjustable

Speed Pump

Adjustable Temp Sensing

Pump

Plug-In to Power Source

Wgt lbs

Order No. Pipe

Size Type

e3-4V/BSPYZ LHB081100101

½”

Sweat

5-28 Watts

■ ■ 3 BH1016

e3-4_/BSXRZ LHB081100102 Sweat ■ 3 BH1016A

e3-4V/BSXRZ LHB081100104 FPT ■ 3 BH1016C

e3-4_/BSTRZ LHB081100106 FPT ■ ■ 3 BH1016E

e3-6V/BSPYZ LHB081100109 Sweat ■ ■ 3 BH1016H

e3-6V/BTXYZ LHB081100112 FPT ■ 3 BH1016K

e3-6V/BTPYZ LHB081100110 FPT ■ ■ 3 BH1016M

e3-4V/BUPYZ 6050B5002 Union

UltraCirc Models

■ ■ 4 BH1016N

e3-4_/BUPRZ 6050B5003 ■ ■ 4 BH1016R

e3-6V/BUPYZ 6050B5004 ■ ■ 4 BH1016T

e3-6_/BSPRZ 6050B5006 ■ ■ 4 BH1016V

e-3 Timer LHB08260002 Three mode timer: ON-OFF-Timer, 30 min. run 0.6 BH1016X Easily attaches on any e3 pump

UltraCirc Model

Click the Order No. for detailed product information.

Sweat Model

FPT Model

e3-6 Pump Curves e3-4 Pump Curves

Page 3: Bell & Gossett EcoCirc 19-16 Circulating Pumps · Operational in 3 different standard control modes: Proportional pressure, constant pressure and constant speed. The night mode functionality

Copyright 1987-2018 State Supply www.StateSupply.com

Toll Free: 800.772.2099 ■ Order Online: www.StateSupply.com ■ Fax: 651.774.7156 ■ [email protected]

11

Bell & Gossett EcoCirc XL High Efficiency Pump

Model No. Cast Iron

Product Code No.

Wgt. lbs.

Model No.

Stainless Steel

Product Code No.

Wgt. lbs.

No. Flange Bolts

Motor Characteristics Cast Iron Order No. HP *Watts

Range Voltage 1 phase

Amp Range A H J K

XL20-35 104300 19.8 XLN20-35 104450LF 22.0 2 1/12 6-85 115 0.1-1.3 9.94 3.16 2.62 .47 BH1127 XL36-45 104301 19.8 XLN36-45 104451LF 22.0 2 1/6 20-200 115 0.1-3.0 9.94 3.16 2.62 .47 BH1127A XL36-45 104302 19.8 XLN36-45 104452LF 22.0 2 1/6 20-200 208-230 0.1-1.5 9.94 3.16 2.62 .47 BH1127C XL15-75 104303 26.4 XLN15-75 104453LF 28.6 4 1/6 30-150 115 0.1-2.3 11.04 4.06 — .56 BH1127E XL15-75 104304 26.4 XLN15-75 104454LF 28.6 4 1/6 30-150 208-230 0.1-1.1 11.04 4.06 — .56 BH1127H XL55-45 104306 26.4 XLN55-45 104456LF 28.6 2 1/2 30-500 208-230 0.2-2.0 11.89 3.16 2.62 .47 BH1127K XL20-140 104308 35.2 XLN20-140 104458LF 39.6 4 1/2 35-470 208-230 0.2-2.0 13.39 4.06 — .56 BH1127M XL65-130 104309 39.6 XLN65-130 104459LF 44.0 2 1 45-825 208-230 0.5-3.5 14.84 3.44 2.86 .47 BH1127P XL40-200 104312 41.8 XLN40-200 104462LF 46.2 4 1 50-825 208-230 0.5-3.5 15.17 4.06 — .56 BH1127R XL70-145 104315 38.4 XLN70-145 104465LF 44.0 2 2 55-1400 208-230 0.6-6.0 14.84 3.44 2.86 .47 BH1127T XL40-275 104318 49.6 XLN40-275 104468LF 55.0 4 2 50-1400 208-230 0.5-6.0 16.04 5.06 — .53 BH1127V

Dimensions, inches

G

4.19

4.19

4.19

5.18

5.18

4.19

5.19

4.62

5.19

4.62

6.00

C

8.20

8.20

8.20

8.39

8.39

10.18

10.41

11.80

11.80

11.80

12.57

B

6.38

6.38

6.38

8.5

8.5

6.38

11.5

11.5

11.5

11.5

12.0

Stainless Steel Order No.

BH1128 BH1128A BH1128C BH1128E BH1128H BH1128K BH1128M BH1128P BH1128R BH1128T BH1128V

Three-Phase Models Coming in the Fall of 2018

Energy Saving ECM Motor, Intelligent Controls and Smart Communication for Commercial Applications The EcoCirc XL Features:

Operational in 3 different standard control modes:

■ Proportional pressure, constant pressure and constant speed. ■ The night mode functionality provides additional energy savings. ■ Advanced settings can be managed from a PC, tablet or Smartphone. ■ Also accessible via optional built-in wireless or RS-485 cable.

User-Friendly Interface:

■ Only four logically placed buttons make it “easy” to set and operate the different pump control modes and advanced communication settings. ■ Even in dark boiler or mechanical rooms, the bright display with large figures and symbols make it easy to view the pump’s status.

Pump Protection:

■ Built-in dry-run protection stops pump operation in the absence of water. ■ Electronics are separated from the pump to prevent condensation from interrupting the pump’s operation. Currently available only in one-phase electrical operation.

Pump Dimensions

High Flow Performance

Range

Use the Stainless Steel pumps for potable water.

Pump Model (ALL)

Iron Flange 3/4”

Bronze Flange 3/4”

Iron Flange

1”

Bronze Flange

1”

Iron Flange 1-1/4”

Bronze Flange 1-1/4”

Iron Flange 1-1/2”

Bronze Flange 1-1/2”

Iron Flange

2”

Bronze Flange

2” 20-35 BG1005 BG1040 BG1010 BG1045 BG1015 BG1050 BG1020 — — 36-45 — — 15-75 — — — — — — — — ¹ BG1072 ¹ BG1073 55-45 BG1005 BG1040 BG1010 BG1045 BG1015 BG1050 BG1020 BG1055 — — 20-140 — — — — — — — — ¹ BG1072 ¹ BG1073 65-130 — — BG1025 BG1060 BG1030 BG1065 BG1035 BG1070 — — 40-200 — — — — — — — — ¹ BG1072 ¹ BG1073 70-145 — — BG1025 BG1060 BG1030 BG1065 BG1035 BG1070 — — 40-275 — — — — — — — — ¹

*BG1072B ¹

*BG1073B

BG1055

Flange Dimensions

Companion Flanges for Pumps, Iron & Bronze Order 2 ea. for complete set. *3” NPT Flange. ¹ Sold by pair

Flange gaskets are included with each new pump. Order flanges separately.

GPM

Feet

of H

ead

4-bolt flange connection shown

*1 horsepower = 745 watts