-
8/11/2019 bdv 7200 en
1/84
4-485-800-14(1)
BDV-N9200W/BDV-N9200WLBDV-N7200W/BDV-N7200WL/BDV-N5200W
Blu-ray Disc/DVD Home TheatreSystem
Operating Instructions
-
8/11/2019 bdv 7200 en
2/84
2GB
Do not install the appliance in aconfined space, such as a
bookcase orbuilt-in cabinet.To reduce the risk of fire, do not
coverthe ventilation opening of the appliancewith newspapers,
tablecloths, curtains,etc.Do not expose the appliance to nakedflame
sources (for example, lightedcandles).To reduce the risk of fire or
electricshock, do not expose this appliance todripping or
splashing, and do not place
objects filled with liquids, such as vases,on the appliance.Do
not expose batteries or applianceswith battery-installed to
excessive heat,such as sunshine and fire.To prevent injury, this
apparatus mustbe securely attached to the floor/wall inaccordance
with the installationinstructions.Indoor use only.
This equipment has been tested andfound to comply with the
limits set outin the EMC Directive using a connectioncable shorter
than 3 meters. (Europemodels only)
On power sourcesThe unit is not disconnected from the
mains as long as it is connected to theAC outlet, even if the
unit itself has
been turned off.As the main plug is used to disconnect
the unit from the mains, connect theunit to an easily accessible
AC outlet.Should you notice an abnormality inthe unit, disconnect
the main plugfrom the AC outlet immediately.
CAUTIONThe use of optical instruments with thisproduct will
increase eye hazard.As the laser beam used in this Blu-rayDisc/DVD
Home Theatre System isharmful to eyes, do not attempt to
disassemble the cabinet.Refer servicing to qualified
personnelonly.
Pick-up unit of this appliance isclassified as a CLASS 3R LASER
product.Visible and invisible laser radiation isemitted when the
laser protectivehousing is opened, so be sure to avoid
direct eye exposure.This marking is located on the
bottomexterior of the main unit.
For customers in Europe andRussia
This appliance is classified as a CLASS 1LASER product. This
marking is locatedon the bottom exterior of the main unit.
For the main unit and surroundamplifierThe nameplate is located
on the bottomexterior.
WARNING
-
8/11/2019 bdv 7200 en
3/84
3GB
Recommended cablesProperly shielded and grounded cablesand
connectors must be used forconnection to host computers
and/orperipherals.
For customers in Europe
Disposal of wastebatteries and electricaland electronicequipment
(applicablein the European Unionand other Europeancountries with
separatecollection systems)
This symbol on the product, the batteryor on the packaging
indicates that theproduct and the battery shall not betreated as
household waste. On certainbatteries this symbol might be used
incombination with a chemical symbol.The chemical symbols for
mercury (Hg)or lead (Pb) are added if the batterycontains more than
0.0005% mercury or0.004% lead. By ensuring these
products and batteries are disposed ofcorrectly, you will help
preventpotentially negative consequences forthe environment and
human healthwhich could otherwise be caused byinappropriate waste
handling. Therecycling of the materials will help toconserve
natural resources.In case of products that for safety,performance
or data integrity reasons
require a permanent connection with anincorporated battery, this
batteryshould be replaced by qualified servicestaff only. To ensure
that the batteryand the electrical and electronicequipment will be
treated properly,hand over these products at end-of-lifeto the
applicable collection point for therecycling of electrical and
electronicequipment. For all other batteries,
please view the section on how toremove the battery from the
productsafely. Hand the battery over to the
applicable collection point for therecycling of waste batteries.
For moredetailed information about recycling ofthis product or
battery, please contactyour local Civic Office, your householdwaste
disposal service or the shopwhere you purchased the product or
battery.
Notice for customers: the followinginformation is only
applicable toequipment sold in countries applyingEU directives.This
product has been manufactured byor on behalf of Sony Corporation,
1-7-1Konan Minato-ku Tokyo, 108-0075Japan. Inquiries related to
product
compliance based on European Unionlegislation shall be addressed
to theauthorized representative, SonyDeutschland GmbH, Hedelfinger
Strasse61, 70327 Stuttgart, Germany. For anyservice or guarantee
matters, pleaserefer to the addresses provided in theseparate
service or guaranteedocuments.
Hereby, Sony Corp., declares
thatBDV-N9200W/BDV-N9200WL/BDV-N7200W/BDV-N7200WL/BDV-N5200W/TA-SA700WR/TA-SA600WR/TA-SA500WR
are incompliance with the essentialrequirements and other
relevantprovisions of Directive 1999/5/EC.For details, please
access the followingURL: http://www.compliance.sony.de/
This product is intended to be used inthe following
countries.AT, BE, BG, HR, CY, CZ, DK, EE, FI, FR, DE,GR, HU, IS,
IE, IT, LV, LI, LT, LU, MT, NL,NO, PL, PT, RO, SK, SI, ES, SE, CH,
GB, AL,BA, MK, MD, RS, ME, Kosovo
5.15 GHz 5.35 GHz band is restricted toindoor operations
only.
-
8/11/2019 bdv 7200 en
4/84
4GB
This Blu-ray Disc/DVD Home TheatreSystem is intended for sound
and videoplayback of discs or USB devices, musicstreaming from an
NFC-compatiblesmartphone or a BLUETOOTH device,and FM tuner. This
system also supportsnetwork streaming and Screen
mirroring.
For customers in AustraliaThis equipment should be installed
andoperated with at least 20 cm and morebetween the radiator and
persons body(excluding extremities: hands, wrists,feet and
ankles).
For customers in Australia andIndia
Disposal of OldElectrical & ElectronicEquipment
(Applicablein the European Unionand other Europeancountries with
separatecollection systems)
For customers in Singapore
On watching 3D video imagesSome people may experiencediscomfort
(such as eye strain, fatigue,
or nausea) while watching 3D videoimages. Sony recommends that
allviewers take regular breaks whilewatching 3D video images. The
lengthand frequency of necessary breaks willvary from person to
person. You mustdecide what works best. If youexperience any
discomfort, you shouldstop watching the 3D video images untilthe
discomfort ends; consult a doctor ifyou believe necessary. You
should alsoreview (i) the instruction manual and/orthe caution
message of any other
device used with, or Blu-ray Disccontents played with this
product and(ii) our website(http://esupport.sony.com/) for
thelatest information. The vision of youngchildren (especially
those under sixyears old) is still under development.
Consult your doctor (such as apediatrician or eye doctor)
beforeallowing young children to watch 3Dvideo images.Adults should
supervise young childrento ensure they follow therecommendations
listed above.
Copy ProtectionPlease be advised of the advanced
content protection systems used inboth Blu-ray Disc and DVD
media.These systems, called AACS (AdvancedAccess Content System)
and CSS(Content Scramble System), maycontain some restrictions on
playback,analog output, and other similarfeatures. The operation of
this productand the restrictions placed may vary
depending on the date of purchase, asthe governing board of the
AACS mayadopt or change its restriction rulesafter the time of
purchase.
Cinavia NoticeThis product uses Cinavia technologyto limit the
use of unauthorized copiesof some commercially-produced filmand
videos and their soundtracks.When a prohibited use of an
unauthorized copy is detected, amessage will be displayed
andplayback or copying will beinterrupted.More information about
Cinaviatechnology is provided at the CinaviaOnline Consumer
Information Centerat http://www.cinavia.com. Torequest additional
information aboutCinavia by mail, send a postcard with
your mailing address to: CinaviaConsumer Information Center,
P.O.Box 86851, San Diego, CA, 92138, USA.
-
8/11/2019 bdv 7200 en
5/84
5GB
Copyrights and TrademarksThis system incorporates with
Dolby*
Digital and Dolby Pro Logic adaptivematrix surround decoder and
the DTS**Digital Surround System.* Manufactured under license
from
Dolby Laboratories. Dolby, Pro
Logic, and the double-D symbol aretrademarks of Dolby
Laboratories.
** For DTS patents, seehttp://patents.dts.com.Manufactured under
license fromDTS Licensing Limited. DTS, DTS-HD,the Symbol, &
DTS and the Symboltogether are registered trademarksof DTS, Inc.
DTS, Inc. All RightsReserved.
This system incorporates High-Definition Multimedia
Interface(HDMI) technology.The terms HDMI and HDMI High-Definition
Multimedia Interface, andthe HDMI Logo are trademarks orregistered
trademarks of HDMILicensing LLC in the United States andother
countries.
Java is a trademark of Oracle and/or its
affiliates.DVD Logo is a trademark of DVD
Format/Logo Licensing Corporation.Blu-ray Disc, Blu-ray, Blu-ray
3D,
BD-LIVE, BONUSVIEW, and logosare trademarks of the Blu-ray
DiscAssociation.
Blu-ray Disc, DVD+RW, DVD-RW,DVD+R, DVD-R, DVD VIDEO, andCD
logos are trademarks.
Super Audio CD is a trademark.App Store is a service mark of
AppleInc.
BRAVIA is a trademark of SonyCorporation.
AVCHD 3D/Progressive and theAVCHD 3D/Progressive logo
aretrademarks of Panasonic Corporationand Sony Corporation.
, XMB, and xross media bar are
trademarks of Sony Corporation andSony Computer Entertainment
Inc.PlayStation is a registered trademark
of Sony Computer Entertainment Inc.
Sony Entertainment Network logoand Sony Entertainment Network
aretrademarks of Sony Corporation.
Music and video recognitiontechnology and related data
areprovided by Gracenote. Gracenote isthe industry standard in
music
recognition technology and relatedcontent delivery. For
moreinformation, please visitwww.gracenote.com.CD, DVD, Blu-ray
Disc, and music andvideo-related data from Gracenote,Inc.,
copyright 2000-presentGracenote. Gracenote Software,copyright
2000-present Gracenote.
One or more patents owned byGracenote apply to this product
andservice. See the Gracenote website fora nonexhaustive list of
applicableGracenote patents. Gracenote, CDDB,MusicID, the Gracenote
logo andlogotype, and the Powered byGracenote logo are either a
registeredtrademark or a trademark ofGracenote, Inc. in the United
States
and/or other countries.
Wi-Fi, Wi-Fi Protected Access andWi-Fi Alliance are
registeredtrademarks of Wi-Fi Alliance.
Wi-Fi CERTIFIED, WPA, WPA2,Wi-Fi Protected Setup, Miracastand
Wi-Fi CERTIFIED Miracast aretrademarks of Wi-Fi Alliance.
The N Mark is a trademark or registeredtrademark of NFC Forum,
Inc. in theUnited States and in other countries.
Android is a trademark of Google Inc.Google Play is a trademark
of Google
Inc.Xperia is a trademark of Sony Mobile
Communications AB.
-
8/11/2019 bdv 7200 en
6/84
6GB
The Bluetooth word mark and logosare registered trademarks owned
byBluetooth SIG, Inc. and any use of suchmarks by Sony Corporation
is underlicense. Other trademarks and tradenames are those of their
respectiveowners.
MPEG Layer-3 audio codingtechnology and patents licensed
fromFraunhofer IIS and Thomson.
This product incorporates proprietarytechnology under license
fromVerance Corporation and is protectedby U.S. Patent 7,369,677
and other U.S.and worldwide patents issued andpending as well as
copyright and trade
secret protection for certain aspects ofsuch technology. Cinavia
is atrademark of Verance Corporation.Copyright 2004-2010
VeranceCorporation. All rights reserved byVerance. Reverse
engineering ordisassembly is prohibited.
Windows Media is either a registeredtrademark or trademark of
MicrosoftCorporation in the United States and/
or other countries.This product is protected by
certainintellectual property rights of MicrosoftCorporation. Use or
distribution ofsuch technology outside of thisproduct is prohibited
without a licensefrom Microsoft or an authorizedMicrosoft
subsidiary.Content owners use MicrosoftPlayReady content access
technology to protect their intellectualproperty, including
copyrightedcontent. This device uses PlayReadytechnology to access
PlayReady-protected content and/or WMDRM-protected content. If the
device fails toproperly enforce restrictions oncontent usage,
content owners mayrequire Microsoft to revoke thedevices ability to
consume PlayReady-protected content. Revocation shouldnot affect
unprotected content orcontent protected by other content
access technologies. Content ownersmay require you to upgrade
PlayReadyto access their content. If you declinean upgrade, you
will not be able toaccess content that requires theupgrade.
DLNA, the DLNA Logo and DLNA
CERTIFIED are trademarks, servicemarks, or certification marks
of theDigital Living Network Alliance.
Opera Devices SDK from OperaSoftware ASA. Copyright
1995-2013Opera Software ASA. All rightsreserved.
All other trademarks are trademarks oftheir respective
owners.
Other system and product names aregenerally trademarks or
registeredtrademarks of the manufacturers. and marks are not
indicated in thisdocument.
End User License Information
Gracenote End User LicenseAgreementThis application or device
containssoftware from Gracenote, Inc. ofEmeryville, California
(Gracenote). Thesoftware from Gracenote (theGracenote Software)
enables this
application to perform disc and/or fileidentification and obtain
music-relatedinformation, including name, artist,track, and title
information (GracenoteData) from online servers or
embeddeddatabases (collectively, GracenoteServers) and to perform
otherfunctions. You may use Gracenote Dataonly by means of the
intended End-Userfunctions of this application or device.You agree
that you will use GracenoteData, the Gracenote Software,
andGracenote Servers for your own
-
8/11/2019 bdv 7200 en
7/84
7GB
personal non-commercial use only. Youagree not to assign, copy,
transfer ortransmit the Gracenote Software or anyGracenote Data to
any third party. YOUAGREE NOT TO USE OR EXPLOITGRACENOTE DATA, THE
GRACENOTESOFTWARE, OR GRACENOTE SERVERS,
EXCEPT AS EXPRESSLY PERMITTEDHEREIN.You agree that your
non-exclusivelicense to use the Gracenote Data, theGracenote
Software, and GracenoteServers will terminate if you violatethese
restrictions. If your licenseterminates, you agree to cease any
andall use of the Gracenote Data, the
Gracenote Software, and GracenoteServers. Gracenote reserves all
rights inGracenote Data, the GracenoteSoftware, and the Gracenote
Servers,including all ownership rights. Under nocircumstances will
Gracenote becomeliable for any payment to you for anyinformation
that you provide. You agreethat Gracenote, Inc. may enforce
itsrights under this Agreement against you
directly in its own name.The Gracenote service uses a
uniqueidentifier to track queries for statisticalpurposes. The
purpose of a randomlyassigned numeric identifier is to allowthe
Gracenote service to count querieswithout knowing anything about
whoyou are. For more information, see theweb page for the Gracenote
PrivacyPolicy for the Gracenote service.
The Gracenote Software and each itemof Gracenote Data are
licensed to youAS IS. Gracenote makes norepresentations or
warranties, expressor implied, regarding the accuracy ofany
Gracenote Data from in theGracenote Servers. Gracenote reservesthe
right to delete data from theGracenote Servers or to change
datacategories for any cause that Gracenotedeems sufficient. No
warranty is madethat the Gracenote Software orGracenote Servers are
error-free or that
functioning of Gracenote Software orGracenote Servers will
beuninterrupted. Gracenote is notobligated to provide you with
newenhanced or additional data types orcategories that Gracenote
may providein the future and is free to discontinue
its services at any time.GRACENOTE DISCLAIMS ALLWARRANTIES
EXPRESS OR IMPLIED,INCLUDING, BUT NOT LIMITED TO,IMPLIED WARRANTIES
OFMERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE, TITLE,
ANDNON-INFRINGEMENT. GRACENOTEDOES NOT WARRANT THE RESULTS
THAT WILL BE OBTAINED BY YOUR USEOF THE GRACENOTE SOFTWARE OR
ANYGRACENOTE SERVER. IN NO CASE WILLGRACENOTE BE LIABLE FOR
ANYCONSEQUENTIAL OR INCIDENTALDAMAGES OR FOR ANY LOST PROFITSOR
LOST REVENUES. Gracenote, Inc. 2013
REAL END USER LICENSE
AGREEMENT (Singapore, China,Thailand, and Taiwan models only)1.
End users are prohibited from
modifying, translating, reverseengineering,
decompiling,disassembling or using other meansto discover the
software developed byReal or otherwise replicate thefunctionality
of the software, exceptto the extent that this restriction is
expressly prohibited by applicablelaw.
2. Real disclaims all warranties andconditions, express and
implied,including implied warranties orconditions of
merchantability andfitness for a particular purpose; andeffectively
exclude all liability forindirect, special, incidental
andconsequential damages, including
but not limited to lost profits orreplacement systems.
-
8/11/2019 bdv 7200 en
8/84
8GB
About These OperatingInstructions
The instructions in these Operating
Instructions describe the controls onthe remote control. You can
also usethe controls on the main unit if theyhave the same or
similar names asthose on the remote control.
In this manual, disc is used as ageneral reference for BDs,
DVDs, SuperAudio CDs, or CDs unless otherwisespecified by the text
or illustrations.
The instructions in this manual are for
BDV-N9200W, BDV-N9200WL,BDV-N7200W, BDV-N7200WL andBDV-N5200W.
BDV-N9200WL is themodel used for illustration purposes.Any
difference in operation is clearlyindicated in the text, for
example,BDV-N9200WL only.
Some illustrations are presented asconceptual drawings, and may
bedifferent from the actual products.
The items displayed on the TV screenmay vary depending on the
area.
The default setting is underlined.
-
8/11/2019 bdv 7200 en
9/84
9GB
Table of Contents
About These Operating
Instructions .......................... 8
Unpacking ..................................11
Guide to Parts and Controls .....14
Getting Started
Step 1: Installing the
Speakers ......................... 20Step 2: Connecting the
System ........................... 20Connecting the speakers ...
21
Connecting the TV ............. 22
Connecting the other
equipment ..................... 23
Connecting the antenna
(aerial) ........................... 25
Step 3: Preparing for Network
Connection ..................... 25
Step 4: Setting up the
Wireless System ............. 26
Step 5: Performing the EasySetup ..............................
27
Step 6: Selecting the Playback
Source ............................ 28
Step 7: Enjoying SurroundSound .............................
29
Playback
Playing a Disc ........................... 31
Playing from a USB Device .......33
Enjoying Music from a
BLUETOOTH Device ............33
Using Screen mirroring .............35
Connecting to a Remote
Device by One-touch
Function (NFC) ................... 36Using SongPal
....................... 38
Playing via a Network .............. 38
Available Options .....................41
Sound Adjustment
Selecting the Audio Format,
Multilingual Tracks, or
Channel .............................. 43
Enjoying Multiplex Broadcast
Sound ................................. 43
TunerListening to the Radio ............. 44
Receiving Radio Data System
(RDS) .................................. 45
-
8/11/2019 bdv 7200 en
10/84
10GB
Other Operations
Using the Control for HDMI
Function for BRAVIA
Sync ....................................45
Calibrating the Appropriate
Speaker Settings
Automatically .....................46Setting the Speakers
................47
Using the Sleep Timer ..............49
Deactivating the Buttons on
the Main Unit ......................49
Changing the Brightness .........49
Enjoying the Visualization on
the TV Screen .....................50
Enjoying SpeakerIllumination ........................50
Saving Power in Standby
Mode .................................. 51Browsing Websites
.................. 51
Further Settings for the
Wireless System .................53
Settings and Adjustments
Using the Setup Display ...........55
[Software Update] ....................55
[Screen Settings] ......................56
[Audio Settings] .......................58
[BD/DVD Viewing Settings] .....59
[Parental Control Settings] .......60
[Music Settings] ........................60
[System Settings] .....................60
[External Input Settings] ..........62[Network Settings]
...................62
[Easy Network Settings] ...........63
[Resetting] ................................63
Additional Information
Precautions ..............................64
Notes about Discs ....................66
Troubleshooting .......................67
Playable Discs .......................... 73
Playable Types of Files .............74
Supported Audio Formats .......76Specifications
...........................76
Language Code List .................79
Index ......................................... 81
-
8/11/2019 bdv 7200 en
11/84
-
8/11/2019 bdv 7200 en
12/84
12GB
(BDV-N9200WL only)
Speaker cords (5, red/white/gray/blue/green)
(BDV-N9200W only) (1, green) (BDV-N9200WL only)
Bases (4)
Lower parts of the front and surroundspeakers (4)
Screws (large) (4)
Screws (small) (12)
BDV-N7200W/BDV-N7200WL only
Front speakers (2), Surround speakers(2)
(BDV-N7200W only)
(BDV-N7200WL only)
Center speaker (1)
Subwoofer (1)
(BDV-N7200W only)
(BDV-N7200WL only)
-
8/11/2019 bdv 7200 en
13/84
13GB
Speaker cords (5, red/white/gray/blue/green)
(BDV-N7200W only) (1, green) (BDV-N7200WL only)
Stands (for front and surroundspeakers) (4)
Screws (8)
BDV-N5200W only
Front speakers (2)
Surround speakers (2)
Center speaker (1)
Subwoofer (1)
-
8/11/2019 bdv 7200 en
14/84
14GB
Guide to Parts and Controls
For more information, refer to the pages indicated in
parentheses.
Top and front panel
A "/1(on/standby)
Turns on the main unit, or sets it tostandby mode.
B Disc lid (page 31)
C Top panel display
D (N-Mark) (page 36)
Position the NFC-compatible devicenear this indication to
activate theNFC function.
E LED indicator
White: Lights up when the main unitis turned on.Blue (for
BLUETOOTH status):
System is ready for pairing:Flashes quickly During pairing:
Flashes quickly NFC device is detected: Flashes Connection is
established: Lights
up
Main unit
1 8 79
2 3
6
4
5
Slot
-
8/11/2019 bdv 7200 en
15/84
15GB
F Soft-touch buttons/indicators
N*(play)
x*(stop)
./>(previous/next)
VOL +/
FUNCTION (page 28)
Selects the playback source.
* Touch and hold Non the main unitfor more than 2 seconds, the
built-insound demonstration will be playedback on the system. If a
USB device isconnected, the audio contents fromthe USB device will
be played back assound demonstration.Touch xto stop the
demonstration.
During the demonstration, the volumelevel may be higher than the
volumelevel you have set.
G (USB) port(page 33)
Place your fingernail in the slot toopen the cover.
H (remote control sensor)
I Z(open/close)
About soft-touch buttons/indicatorsThe soft-touch button
indicators flash
each time you turn on the main unit,wait until the indicators
stop flashing.The buttons only function when theindicators are
lit.
These buttons work when you touchthem lightly. Do not press on
them withexcessive force.
If the button does not work, release thebutton and wait for a
few seconds. Then,touch the button again with your fingercovering
the button indicator.
Indicators in the top panel display
* High-bandwidth Digital Content Protection** When you press
DISPLAY, the stream information/decoding status is displayed
when
the function is set to TV. The stream information/decoding
status may not appeardepending on the stream or item being
decoded.
Note
Note
Stereo soundis received(Radio only)
Repeat playMuting is on
The HDMI (OUT) jackis correctlyconnected to anHDCP*
compliantequipment withHDMI input
The systems status(radio frequency, etc.)**
BLUETOOTH poweris on
-
8/11/2019 bdv 7200 en
16/84
16GB
Rear panel
A SPEAKER ILLUMINATION terminals(BDV-N9200WL/BDV-N7200WLonly)
(page 21)
B TV (DIGITAL IN OPTICAL) jack
(pages 22, 23)C A.CAL MIC jack (BDV-N9200W/
BDV-N9200WL/BDV-N7200W/BDV-N7200WL only) (pages 28,47)
D AUDIO IN (L/R) jacks (pages22, 23)
E ANTENNA (FM COAXIAL 75 ) jack(page 25)
F HDMI (OUT) jack (page 22)
G HDMI (IN 1/IN 2) jacks (page 23)
H LAN (100) terminal (page 25)
I SPEAKERS jacks (page 21)
A "/1(on/standby)B LINK/STANDBY indicator
(page 27)
You can check the status of wirelesstransmission between the
main unitand surround amplifier.
C SPEAKERS jacks
D SPEAKER ILLUMINATION terminals(BDV-N9200WL/BDV-N7200WLonly)
(page 21)
E SECURE LINK button (page 53)
Starts the Secure Link function.
1 542
9 8 67
3
Surround amplifier
312 54
Front panel Rear panel
-
8/11/2019 bdv 7200 en
17/84
17GB
AUDIO, N, and 2+ buttons have atactile dot. Use the tactile dot
as areference when operating the remotecontrol.
: For TV operations
(For details, see Preparing the remotecontrol for controlling
your TV(page 19).)
A Z(open/close)
Opens or closes the disc lid.
SPEAKERS TVyAUDIO
Selects whether TV sound is outputfrom the systems speakers or
the
TVs speaker(s). This function worksonly when you set [Control
forHDMI] to [On] (page 60).
TV "/1(on/standby) (page 19)
Turns on the TV or sets it to standbymode.
"/1(on/standby) (page 28)
Turns on the system or sets it to
standby mode.B SPEAKER ILLUMINATION
(page 50)
Selects the illumination pattern onthe speakers.
COLOUR PATTERN (page 50)
VISUALIZER (page 50)
Selects the visualization pattern.
DIMMER (page 49)
Adjusts the brightness of the toppanel display, soft-touch
buttonsindicators, LED indicator, and theillumination* on the
speakers.
* BDV-N9200WL/BDV-N7200WL only
C Sound field buttonsSee Step 7: Enjoying SurroundSound (page
29).
CLEARAUDIO+, SOUND FIELD,
MUSIC EQ, GAME, NIGHT,CONCERT HALL, FOOTBALL,CINEMA STUDIO,
MUSIC ARENA
D Color buttons
Shortcut keys for selecting items onsome BD menus (can also be
usedfor Java interactive operations onBDs).
E TOP MENU
Opens or closes the BDs or DVDsTop Menu.
POP UP/MENU
Opens or closes the BD-ROMsPop-up Menu, or the DVDs menu.
OPTIONS (pages 30, 41, 52)
Displays the options menu on theTV screen or in the top
paneldisplay. (The location differs
depending on the selectedfunction.)
Remote control
BDV-N9200WL/
BDV-N7200WL
BDV-N9200W/
BDV-N7200W/
BDV-N5200W
1
2
3
4
5
7
6
8
9
-
8/11/2019 bdv 7200 en
18/84
18GB
RETURN
Returns to the previous display.
B/V/v/b
Moves the highlight to a displayeditem.
V/v are shortcut keys for track searchduring music CD
playback.
(enter)
Enters the selected item.
F MIRRORING (pages 35, 38)
Selects the SCR M function.
BLUETOOTH (page 34)
Selects the BT function.
HOME (pages 28, 47, 55)
Enters or exits the systems homemenu.
SEN
Accesses the Sony EntertainmentNetwork online service.
FUNCTION (page 28)
Selects the playback source.
By setting [Input Skip Setting](page 62), you can skip
unusedinputs when selecting a function.
G DISPLAY (pages 32, 39, 45, 52)
Displays playback and webbrowsing information on the
TVscreen.Displays the preset radio station,frequency, etc., in the
top paneldisplay.
SLEEP (page 49)
Sets the sleep timer.
AUDIO (page 43)
Selects the audio format/track.
SUBTITLE
Selects the subtitle language whenmultilingual subtitles are
recordedon a BD-ROM/DVD VIDEO.
3D
Converts 2D content into simulated3D content when connected to
a3D-compatible device.
H Playback operation buttons
See Playback (page 31).
m/M(fast/slow/freeze frame)Fast reverse/fast forward
duringplayback. Each time you press thebutton, the search speed
changes.
Activates slow-motion play whenpressed for more than one
secondin pause mode.
Plays one frame at a time whenpressed in pause mode.
During Blu-ray 3D Disc playback, slow-motion reverse play and
single-framereverse play are not available.
./>(previous/next)
Selects the previous/next chapter,track, or file.
N(play)
Starts or re-starts playback (resumeplay).Activates One-Touch
Play(page 45)when the system is on and set tothe BD/DVD
function.
X(pause)
Pauses or re-starts playback.
x(stop)
Stops playback and remembers the
stop point (resume point). Theresume point for a title/track is
thelast point you played or the lastphoto for a photo folder.Stops
the built-in or USB sounddemonstration.
Radio operation buttons
See Tuner (page 44).
TUNING +/
PRESET +/
Tip
Note
-
8/11/2019 bdv 7200 en
19/84
19GB
I (muting)
Turns off the sound temporarily.
2(volume) +/Adjusts the volume.
TV 2(volume) +/Adjusts the TV volume.
TVt
(input)
Switches the TVs input sourcebetween the TV and other
inputsources.
Preparing the remote control forcontrolling your TVBy adjusting
the remote control signal,you can control your TV with the
supplied remote control.
When you replace the batteries of theremote control, the code
number mayreset to the default (SONY) setting. Set theremote
control again.
1 Hold down TV ?/1.
2 Press the corresponding button foryour TV (see table below),
then press
.
The TVs manufacturers codes areregistered to the buttons in the
tableabove. If the setting is unsuccessful, thecurrently registered
code is notchanged. Press the corresponding
button again.If more than one button is listed, trypressing them
one at a time until youfind the button that works with your TV.
3 Release TV ?/1.Now you can use the TV ?/1,
TV 2+/ and TVtbuttons tocontrol your TV.
Note
Manufacturer Button
SONY (default) CLEARAUDIO+
LG MUSIC EQ
PANASONIC GAME
PHILIPS NIGHT,CINEMA STUDIO,MUSIC ARENA
SAMSUNG SOUND FIELD,MUSIC EQ,MUSIC ARENA
SHARP CONCERT HALL
TOSHIBA FOOTBALL
Note
-
8/11/2019 bdv 7200 en
20/84
20GB
Getting
Started
Step 1: Installing the
SpeakersInstall the speakers by referring to theillustration
below.To assemble the speakers, refer to thesupplied Speaker
Installation Guide.
AFront left speaker (L)BFront right speaker (R)CCenter
speakerDSurround left speaker (L)ESurround right speaker
(R)FSubwooferGTV
Installing the surround speakersin rear position(Speaker layout:
[Standard])
Installing all speakers in frontposition
(Speaker layout: [All Front])
Be sure to select the speakers layoutsetting (page 47) according
to yourspeakers placement.
Use caution when placing the speakersand/or speaker stands
attached to the
speakers on a specially treated (waxed,oiled, polished, etc.)
floor, as staining ordiscoloration may result.
Do not lean or hang on a speaker, as itmay fall down.
The speakers of this system are notmagnetically shielded. This
may result incolor irregularity when they are placednear a CRT TV
or projector.
In order to output more effective soundwhen [All Front] setting
is selected, werecommend you to install your frontspeakers and
surround speakers closer toeach other.
You can install the speakers on a wall. Fordetails, refer to the
supplied SpeakerInstallation Guide.
Step 2: Connecting theSystem
Do not connect the AC power cord(mains lead) of the main unit to
a walloutlet (mains) until all the otherconnections are made.
When you connect other equipment with avolume control, turn down
the volume ofthe equipment to a level where sound isnot
distorted.
Getting Started
F
D E
A G C B
DA G C B E
F
Note
Tip
Note
-
8/11/2019 bdv 7200 en
21/84
21GB
GettingS
tarted
Connect the speaker cords to match thecolor of the SPEAKERS
jacks of the mainunit and surround amplifier. Be sure toinsert the
speaker connector until it
clicks.
To the main unit
To the surround amplifier
To connect the SPEAKERILLUMINATION
terminal(BDV-N9200WL/BDV-N7200WL only)
Connect the speaker illuminationconnector (attached with the
speaker
cord) to the main unit and surroundamplifier so you can enjoy
the lightingeffect on your speakers.You can select the illumination
patternyou want by pressing SPEAKERILLUMINATION repeatedly (page
50).
To the main unit
To the surround amplifier
Connecting the speakers
Purple(Subwoofer)
White(Front leftspeaker (L))
Green(Centerspeaker)
Red(Front rightspeaker (R))
Gray(Surround rightspeaker (R))
Blue(Surroundleft speaker
(L))
Front leftspeaker (L)
Front rightspeaker (R)
Surround rightspeaker (R)
Surround leftspeaker (L)
-
8/11/2019 bdv 7200 en
22/84
22GB
Getting
Started
Select one of the following connection methods according to the
input jacks on yourTV.
Video connection
1) High Speed HDMI cable2) The Audio Return Channel (ARC)
functionenables the TV to output sound through the
system with an HDMI connection, without performing the
BorCconnection below. To
set the ARC function on this system, see [Audio Return Channel]
(page 61). To check thecompatibility of your TVs ARC function,
refer to the operating instructions supplied withyour TV.
Audio connections
If your TVs HDMI jack is not compatible with the ARC function,
make an appropriateaudio connection (BorC) for listening to TV
sound via the systems speakers.
Connecting the TV
A
CB
A
HDMI cable1)(supplied with Africa, India,Middle East, Singapore,
China, Thailand,
and Taiwan models only)or
2)
B High quality
C
Standard quality
Optical digital cord(not supplied)
OPTICALDIGITAL OUT
L
R
AUDIOOUTPUT
Audio cable (not supplied)
-
8/11/2019 bdv 7200 en
23/84
23GB
GettingS
tarted
To enjoy TV sound, select TV function for connection Bor AUDIO
function forconnectionC.
Connect the system, TV and other equipment as follows.You cannot
enjoy the audio and video of the connected equipment on the
TVthrough this system when the system is off or in standby
mode.
* This connection is unnecessary for connectionA(HDMI
connection).
Select one of the following connection methods according to the
jack type of theequipment.
Note
Connecting the other equipment
SystemSignal flow
TV
: Audio signal
: Video signal
Equipment(Set-top box, VCR, PlayStation, ordigital satellite
receiver, etc.)
Video out*
A B,C
CB
A
CB
A
-
8/11/2019 bdv 7200 en
24/84
24GB
Getting
Started
When you make connectionAThis connection can transmit both video
and audio signals.
Video signals from the HDMI (IN 1/2) jacks are output to the
HDMI (OUT) jack only whenthe HDMI1 or HDMI2 function is
selected.
To output an audio signal from the HDMI (IN 1/2) jacks to the
HDMI (OUT) jack, you mayneed to change the audio output setting.
For details, see [Audio Output] in [AudioSettings] (page 58).
You can change the audio input of an equipment that is connected
to the HDMI (IN 1) jackto the TV (DIGITAL IN OPTICAL) jack. For
details, see [HDMI1 Audio Input mode] in [HDMISettings] (page 61).
(Europe models only.)
When you make connectionB,C
Connect the system so that video signals from the system and
other equipment areoutput to the TV, and audio signals from the
equipment are output to the system.
If you make either connection above, set [Control for HDMI] in
[HDMI Settings] of [SystemSettings] to [Off] (page 60).
You can enjoy equipment sound by selecting TV function for
connectionBor AUDIOfunction for connectionC.
A High quality
B
C
Standard quality
Note
Note
HDMI cable*(not supplied)
*High Speed HDMI cable
OPTICAL
DIGITAL OUT
L
R
AUDIOOUTPUT
HDMI OUT
Optical digital cord(not supplied)
Audio cable (not supplied)
-
8/11/2019 bdv 7200 en
25/84
25GB
GettingS
tarted
Rear of the main unit
Be sure to fully extend the FM wire
antenna (aerial). After connecting the FM wire antenna
(aerial), keep it as horizontal as possible.
If you have poor FM reception, use a75-ohm coaxial cable (not
supplied) toconnect the main unit to an outdoor FMantenna
(aerial).
Step 3: Preparing forNetwork Connection
To connect the system to your network,perform [Easy Network
Settings]. Fordetails, see Step 5: Performing the EasySetup (page
27).
Select the method based on your LAN(Local Area Network)
environment. If you use a wireless LAN
The system has built-in Wi-Fi, and youcan connect the system to
the networkby making the network settings.
If you use a wired LANUse a LAN cable to connect to the LAN(100)
terminal on the main unit.
We recommend that you use a shieldedand straight interface cable
(LAN cable).
Connecting the antenna(aerial)
Note
Tip
FM wire antenna (aerial)(supplied)
or
Tip
Tip
Broadband router
LAN cable (not supplied)
-
8/11/2019 bdv 7200 en
26/84
26GB
Getting
Started
Before performing the networksettings
When your wireless LAN router (accesspoint) is Wi-Fi Protected
Setup (WPS)-compatible, you can easily set thenetwork settings with
the WPS button.
If not, check the following information inadvance, and record it
in the spaceprovided below. The network name (SSID*) that
identifies your network.**
If security is set on your wireless
network, the security key (WEP key,WPA key).**
* SSID (Service Set Identifier) is a namethat identifies a
particular wirelessnetwork.
** You need to check the settings of yourwireless LAN router to
get theinformation about SSID and security key.For details: visit
the following website:
For customers in Europe and
Russia:http://support.sony-europe.com/
For customers in other
countries/regions:http://www.sony-asia.com/section/support
refer to the operating instructionssupplied with the wireless
LAN router
consult the manufacturer of thewireless LAN router
About wireless LAN securitySince communication via the
wirelessLAN function is established by radiowaves, the wireless
signal may besusceptible to interception. To protectwireless
communication, this systemsupports various security functions.
Besure to correctly configure the securitysettings in accordance
with yournetwork environment.
x No SecurityAlthough you can easily make settings,anyone can
intercept wirelesscommunication or intrude into yourwireless
network, even without anysophisticated tools. Keep in mind
thatthere is a risk of unauthorized access or
interception of data.
x WEPWEP applies security tocommunications to prevent
outsidersfrom intercepting communications orintruding into your
wireless network.WEP is a legacy security technology thatenables
older devices which do notsupport TKIP/AES to be connected.
x WPA-PSK (TKIP), WPA2-PSK(TKIP)
TKIP is a security technology developedin response to the
deficiencies of WEP.TKIP assures a higher security level
thanWEP.
x WPA-PSK (AES), WPA2-PSK (AES)AES is a security technology that
uses anadvanced security method distinct fromWEP and TKIP. AES
assures a highersecurity level than WEP or TKIP.
Step 4: Setting up theWireless System
The main unit transmits sound to thesurround amplifier that is
connected tothe surround speakers. To activatewireless
transmission, perform thefollowing Steps.
1 Connect the AC power cord (mainslead) of the main unit.
Before connecting the AC power
cord, make sure all connections inStep 2: Connecting the
System(page 20)are secure.
-
8/11/2019 bdv 7200 en
27/84
27GB
GettingS
tarted
2 Press "/1to turn on the system.
3 Connect the AC power cord (mainslead) of the surround
amplifier.
When wireless transmission isactivated, the
LINK/STANDBYindicator turns green.If the LINK/STANDBY indicator
doesnot turn on, see Wireless sound(page 70).
About the LINK/STANDBYindicator
The LINK/STANDBY indicator showswireless transmission status as
follows.
About the standby mode
The surround amplifier enters standbymode automatically when the
main unitis in standby mode or wirelesstransmission is
deactivated.The surround amplifier turns on
automatically when the main unit isturned on and wireless
transmission isactivated.
To specify the wirelessconnection
If you use multiple wireless products oryour neighbors use
wireless products,interference may occur. To prevent this,you can
specify the wireless connection
to link the main unit to the surroundamplifier (Secure Link
function). Fordetails, see Further Settings for theWireless System
(page 53).
Step 5: Performing the
Easy SetupFollow the Steps below to make thebasic adjustments
and network settingsfor the system.Displayed items vary depending
on thearea.
1 Insert two R03 (AAA) batteries(supplied) by matching the
3and
#ends on the batteries to themarkings inside the
compartment.
2 Turn on the TV.
Turns greenThe system is turned on, wirelesstransmission is
activated and surroundsignals are being received.
Turns orangeThe system is turned on, wirelesstransmission is
activated with the Secure Linkfunction, and surround signals are
beingreceived.
Flashes green or orange slowlyWireless transmission is
deactivated.
Turns redThe surround amplifier is in standby modewhile the
system is in standby mode orwireless transmission is
deactivated.
Turns offThe surround amplifier is turned off.
Flashes redThe surround amplifiers protection is active.
"/1
LINK/STANDBY indicator
-
8/11/2019 bdv 7200 en
28/84
28GB
Getting
Started
3 Connect the calibration mic to theA.CAL MIC jack on the rear
panel.
(BDV-N9200W/BDV-N9200WL/
BDV-N7200W/BDV-N7200WL
only)
Set up the calibration mic at ear
level using a tripod, etc. (notsupplied). The calibration
micshould aim the TV screen. The frontof each speaker should face
thecalibration mic, and there should beno obstruction between
thespeakers and the calibration mic.
4 Press [/1to turn on the system.
5 Switch the input selector on yourTV so that the signal from
thesystem appears on the TV screen.
The [Easy Initial Settings] for OSDlanguage selection
appears.
6 Perform [Easy Initial Settings].Follow the on-screen
instructions
to make the basic settings using
B/V/v/band .
For details about [Auto Calibration],see Calibrating the
AppropriateSpeaker Settings Automatically(page 46).
(BDV-N9200W/BDV-N9200WL/BDV-N7200W/BDV-N7200WL only)
7 After completing the [Easy InitialSettings], pressV/vto select
[Easy
Network Settings], then press .
The [Easy Network Settings] displayappears.
8 Follow the on-screen instructionsto make the network
settingsusing B/V/v/band .
If the system cannot connect to thenetwork, see Network
connection(page 72)or Wireless LANconnection (page 72).
To recall the [Easy NetworkSettings] display
1 Press HOME.The home menu appears on the TVscreen.
2 Press B/bto select [Setup].
3 Press V/vto select [Easy NetworkSettings], then press .
Step 6: Selecting thePlayback Source
Press FUNCTION repeatedly.
When you press FUNCTION once, thecurrent function appears in the
toppanel display, then each time you pressFUNCTION, the function
changescyclically as follows.
BD/DVD tUSB tFMtHDMI1tHDMI2tTVtSCR MtBTtAUDIO
B/V/v/b
BD/DVDDisc or network device to be played by thesystem
USBUSB device that is connected to the (USB)
port (page 14)
-
8/11/2019 bdv 7200 en
29/84
29GB
GettingS
tarted
Some functions may be changed via theTV screen by pressing
FUNCTION, V/v,and .
You can also press BLUETOOTH and
MIRRORING on the remote control toselect BT and SCR M
functionrespectively.
Step 7: EnjoyingSurround Sound
After performing the previous Steps andstarting playback, you
can easily enjoypre-programmed sound fields that aretailored to
different kinds of soundsources. They bring the exciting
andpowerful sound into your home.
The sound field can be selected only when
[Sound Effect] is set to [Sound Field On](page 59). When [Sound
Effect] is set toother than [Sound Field On], the soundfield
setting does not apply.
Press SOUND FIELD repeatedly during
playback.
You can also press CLEARAUDIO+,GAME and NIGHT to select
respective
sound field.
To enjoy 2-channel source such as a CD inmulti-channel output,
we recommendyou to select [ClearAudio+].
If you set the sound field to [ClearAudio+]and play Internet
content of the BerlinPhilharmonic, the [Philharmonic Hall]mode
(page 30) is automatically selected(only for areas that are offered
theservice).
When the speaker layout is set to [All
Front] and you play back multi-channelsource, select
[ClearAudio+], [Movie],[Game] or [Night] to enjoy virtualsurround
sound.
FMFM radio (page 44)
HDMI1/HDMI2Equipment that is connected to the HDMI(IN 1) or HDMI
(IN 2) jack(page 23)
TVEquipment (TV, etc.) that is connected to the
TV (DIGITAL IN OPTICAL) jack, or a TVcompatible with the Audio
Return Channelfunction that is connected to the HDMI (OUT)
jack (pages 22,23)
SCR M[Screen mirroring]Screen mirroring-compatible device
(pages 35, 37)
BT[Bluetooth AUDIO]
BLUETOOTH device that supports A2DPAUDIOEquipment that is
connected to the AUDIO IN
(L/R) jacks (pages 22, 23)
Tip
Note
Selecting the sound field
ClearAudio+You can enjoy the sound with Sony-recommended sound
field. Sound field isautomatically optimized according toplayback
content and function. 2-channel source: The system will
recreate
5.1 channel speaker output. Multi-channel source: The system
outputs
sound from the speakers as it was recorded.
MovieThe system provides the optimized sound forwatching
movies.
MusicThe system provides the optimized sound forlistening to
music.
Digital Music Enhancer[Digital Music]This is a technology
developed by Sony toenhance the sound quality of compressedaudio
files by restoring high frequency range
sound after compression process.
GameThe system provides the optimized sound forplaying video
games.
NightSuitable for watching movies at night byreducing loud
sounds while maintaining cleardialog.
Tip
-
8/11/2019 bdv 7200 en
30/84
30GB
Getting
Started
To select the sound field from theoption menu
1 Press OPTIONS and V/vto select[Sound Field], then press .
2 Press V/vto select the sound field,
then press .
To select the pre-programmedmusic equalizer
Press MUSIC EQ repeatedly duringplayback.You can select the
sound to suit yourpreference.Each time you press the button,
thesetting changes cyclically as
follows.[Standard]t[Rock]t[Hiphop]t[Electronica]
You can also select the music equalizerfrom the option menu.
Follow steps 1and 2 above. Select [Music] in step 2.Then, press
V/vand to select thesetting.
You can bring the exciting and powerfulsound of movie theaters
and concerthalls into your home by selecting one ofthe following
sound fields.
Press CONCERT HALL to select
[Philharmonic Hall : On].The system reproduces the
soundcharacteristics of a Berlin philharmonichall. This mode can
reproducehi-resolution sound.
Press CINEMA STUDIO to select
[Cinema Studio 9.1ch : On].
This system reproduces the soundcharacteristics of the cinema
productionstudio. This setting can expand a sourcesound up to 9.1
channels to which avertical component is applied, and givea
dimension of presence and depth.
Press MUSIC ARENA to select [Music
Arena : On].
You can enjoy Live Music Concert filledwith great excitement
created by Sonyunique Audio DSP technology. (DigitalMusic
Arena)
To select the advanced soundfield from the option menu
1 Press OPTIONS and V/vto select[Cinema Studio 9.1ch], [Music
Arena]
or [Philharmonic Hall], then press .
2 Press V/vto select [On], then press.
The advanced sound fields areautomatically set to [Off] when
youperform the following. Turn off the system. Press any of the
sound field buttons
(page 17).
Selecting the advancedsound field
Note
-
8/11/2019 bdv 7200 en
31/84
31GB
Playback
To select the football mode
Press FOOTBALL repeatedly while
watching a football match broadcast.
You can experience a feeling ofpresence in the stadium when
watching
the football match broadcast. [Football : Narration On]: You
can
enjoy an immersive feeling of being ina football stadium through
enhancedstadium cheers.
[Football : Narration Off]: You canenjoy a more immersive
feeling ofbeing in a football stadium byminimizing the volume level
ofnarration in addition to the
enhancement of cheers. [Football Off]: The football mode is
turned off.
We recommend you to select the footballmode when watching a
football matchbroadcast.
If you hear unnatural sound in the contentwhen [Football :
Narration Off] is selected,
[Football : Narration On] isrecommended.
The football mode is automatically set to[Football Off] when you
perform thefollowing. Turn off the system. Press any of the sound
field buttons
(page 17). This feature does not support monaural
sound.
You can also select the football modefrom the option menu.
If 5.1 channel audio stream is available,we recommend you to
select it on your TVor set-top box.
Playing a Disc
For playable discs, see Playable Discs(page 73).
1 Switch the input selector on yourTV so that the signal from
the
system appears on your TV
screen.
2 Press Z, and place a disc on thedisc compartment until it
clicks.
3 Press Zto close the disc lid.Playback starts.If playback does
not startautomatically, select in the
[Video], [Music], or[Photo] category, and press .
Some BD-ROMs with BD-LIVE Logo*have bonus content and other data
thatcan be downloaded for enjoyment.
*
1 Connect the USB device to the(USB) port (page 33).
For local storage, use a 1 GB or
larger USB memory.
Note
Tip
Playback
Enjoying BONUSVIEW/BD-LIVE
-
8/11/2019 bdv 7200 en
32/84
32GB
2 Prepare for BD-LIVE (BD-LIVEonly).
Connect the system to a network(page 25).
Set [BD Internet Connection] to[Allow] (page 59).
3 Insert a BD-ROM withBONUSVIEW/BD-LIVE.
The operation method differsdepending on the disc. Refer to
theoperating instructions of the disc.
To delete data in the USB memory, select[Delete BD Data] in
[Video], and press
. All data stored in the buda folder will bedeleted.
You can enjoy Blu-ray 3D Discs with the
3D logo*.
*
1 Prepare for Blu-ray 3D Discplayback.
Connect the system to your3D-compatible TV using a HighSpeed
HDMI cable (page 22).
Set [3D Output Setting] and [TVScreen Size Setting for 3D]
in[Screen Settings] (page 56).
2 Insert a Blu-ray 3D Disc.The operation method differsdepending
on the disc. Refer to theoperating instructions supplied withthe
disc.
Refer also to the operating instructions ofyour 3D-compatible
TV.
You can check the playbackinformation, etc., by pressing
DISPLAY.The displayed information differsdepending on the disc type
and systemstatus.
Example: when playing a BD-ROM
A Output resolution/Video frequency
B Title number or name
C The currently selected audio settingD Available functions (
angle,
audio, subtitle)
E Playback informationDisplays play mode, playing status
bar, disc type, video codec, bit rate,
repeat type, elapsed time, total
playing time
F Chapter number
G The currently selected angle
Tip
Enjoying Blu-ray 3D
Tip
Displaying the playbackinformation
-
8/11/2019 bdv 7200 en
33/84
33GB
Playback
Playing from a USBDevice
You can play video/music/photo files
on a connected USB device.For playable types of files,
seePlayableTypes of Files (page 74).
1 Connect the USB device to the(USB) port.
Refer to the operating instructionsof the USB device
beforeconnecting.
2 Press HOME.The home menu appears on the TV
screen.
3 Press B/b to select [Video],[Music], or [Photo].
4 Press V/vto select [USBdevice], then press .
Do not remove the USB device during
operation. To avoid data corruption ordamage to the USB device,
turn the systemoff before connecting or removing the USBdevice.
Enjoying Music from aBLUETOOTH Device
BLUETOOTH wireless technology is ashort-range wireless
technology thatenables wireless data communicationbetween digital
devices. BLUETOOTHwireless technology operates within arange of
about 10 meters.
Supported BLUETOOTH versionand profiles
Profile refers to a standard set ofcapabilities for various
BLUETOOTHproduct capabilities. For details on thesupported
BLUETOOTH version andprofiles, see BLUETOOTH Section(page 77).
Depending on the specifications of theBLUETOOTH device, the
functions may
differ even though the device supportsthe same profile as this
system.
The audio playback on this system maybe delayed from that on the
BLUETOOTHdevice because of the characteristics ofthe BLUETOOTH
wireless technology.
Note
About the BLUETOOTHwireless technology
Note
-
8/11/2019 bdv 7200 en
34/84
34GB
Pairing is an operation whereBLUETOOTH devices register with
eachother beforehand. Once a pairingoperation is performed, it does
not needto be performed again.
1 Place the BLUETOOTH devicewithin 1 meter from the main
unit.
2 Press BLUETOOTH.You can also select [BluetoothAUDIO] from
[Input] in home
menu.3 Set the BLUETOOTH device inpairing mode.
For details on setting theBLUETOOTH device in pairing mode,refer
to the operating instructionssupplied with the device.
4 Select your systems name (forexample, BDV-N9200W) on the
devices display.Perform this step within 5 minutes,otherwise
pairing will be canceled.
If passkey is required on theBLUETOOTH device, enter
0000.Passkey may be called Passcode,PIN code, PIN number
orPassword.
You can change the systems nameappears on your device by
using[Device Name] in [System Settings](page 62).
5 Once pairing is completed, thedevice is automatically
connected
to the system.
Device name appears on the TVscreen.
You can pair up to 9 BLUETOOTHdevices. If the 10th BLUETOOTH
deviceis paired, the least recently connecteddevice will be
replaced by the newone.
6 Start playback on the BLUETOOTHdevice.7 Adjust the volume.
Adjust the volume of theBLUETOOTH device first, if thevolume
level is still too low, adjustthe volume level on the main
unit.
To cancel pairing operation
Press HOME or FUNCTION.
You can connect to a BLUETOOTHdevice from this main unit.Check
the following before playing
music: The BLUETOOTH function of the
BLUETOOTH device is turned on. The pairing has been
completed
(page 34).
1 Press BLUETOOTH.
To connect to the most recentconnected BLUETOOTH device, pressN.
Then proceed to Step 5.
2 Press OPTIONS.3 Select [Device List], then press .
A list of paired BLUETOOTH devicesappears.
4 Press V/vrepeatedly to select thedevice you want, then press
.
5 Press Nto start playback.
Pairing this system with aBLUETOOTH device
Note
Tip
Note
Connecting to a BLUETOOTHdevice from this system
Note
-
8/11/2019 bdv 7200 en
35/84
35GB
Playback
6 Adjust the volume.Adjust the volume of theBLUETOOTH device
first, if thevolume level is still too low, adjustthe volume level
on the main unit.
Once the main unit and the BLUETOOTHdevice are connected, you
can controlplayback by pressing N, X, x, m/Mand ./>.
You can connect to the system from apaired BLUETOOTH device in
functionsother than BT, if you set [BluetoothPower Setting] in
[External Input Settings]to [On] (page 62).
You can enable or disable the reception ofAAC audio from
BLUETOOTH device(page 62).
To disconnect the BLUETOOTHdevice
Press HOME, FUNCTION or RETURN.
To delete a paired BLUETOOTHdevice from the device list
1 Follow Steps 1 to 3 above.
2 Press V/vrepeatedly to select thedevice, then press
OPTIONS.
3 Press V/vrepeatedly to select[Remove], then press .
4 Press B/brepeatedly to select [OK],then press .
Using Screen mirroring
Screen mirroring is a function todisplay the screen of a mobile
device onthe TV by Miracast technology.
The main unit can be connected directlywith a Screen
mirroring-compatibledevice (e.g. smartphone, tablet). Youcan enjoy
the display screen of thedevice on your large TV screen. Nowireless
router (or access point) isrequired to use this feature.
1 Press MIRRORING.
2 Follow the on-screen instructions.Activate the Screen
mirroringfunction from your device.For details on how to activate
thefunction, refer to the operatinginstructions supplied with
yourdevice.
When using Screen mirroring, the qualityof picture and sound may
sometimes bedeteriorated due to interference fromother network.
Some network functions may not beavailable during Screen
mirroring.
Make sure that the device is compatiblewith Miracast.
Connectivity with allMiracast compatible devices is
notguaranteed.
Depending on the usage environment,
the quality of the picture and sound maybe deteriorated.
You can also wirelessly mirror your entireXperia smartphone
screen on a large TVscreen by using One-touch mirroringfunction
(NFC) (page 37).
Note
Tip
Note
Tip
-
8/11/2019 bdv 7200 en
36/84
36GB
Connecting to a RemoteDevice by One-touchFunction (NFC)
What is NFC?NFC (Near Field Communication) is atechnology
enabling short-rangewireless communication betweenvarious devices,
such as mobile phonesand IC tags. Thanks to the NFC function,data
communication can be achievedeasily just by holding the device
near
the (N-Mark) on the
NFC-compatible devices.
The system only can recognizes andconnects to one NFC-compatible
deviceat a time.
Depending on your remote device, youmay need to turn on the NFC
function onyour remote device in advance. Fordetails, refer to the
operating instructions
of the remote device. To use the NFC function, be sure to
set
[NFC] to [On] (page 61).
By holding an NFC-compatible remote
device near to the N-Markon the mainunit, the main unit and
remote deviceproceed to complete pairing and theBLUETOOTH
connection automatically.
1 Download and install the NFCEasy Connect application.
NFC Easy Connect is a freeapplication for Android remotedevices
that can be obtained onGoogle Play. Search for theapplication using
the keyword NFCEasy Connect on the site, or access
the download site directly byreading the two-dimensional
codebelow.Note that NFC Easy Connect is freebut data communication
fees whendownloading are chargedseparately.
Two-dimensional code* for direct
access
* Use a two-dimensional code readerapplication.
Note
Connecting to a remotedevice by One-touchlistening function
(NFC)
Compatible remote devicesRemote devices with a built-in
NFCfunction(OS: Android 2.3.3 4.x.x excludingAndroid 3.x)
-
8/11/2019 bdv 7200 en
37/84
37GB
Playback
The application may not be availablein some
countries/regions.
2 Start the NFC Easy Connectapplication on the remote
device.
Make sure that the applicationscreen is displayed.
3 Hold the remote device near tothe N-Mark on the main unit
(page 36)until the remote device
vibrates.
Vibration cue is provided when theremote device is recognized by
themain unit. Follow the on-screen
instructions displayed on theremote device, and complete
theprocedure for BLUETOOTHconnection.When the BLUETOOTH
connectionis established, the blue LEDindicator on the top panel
stopsflashing. The playback time appearsin the top panel
display.
For some remote devices, this functionmay be available without
downloadingNFC Easy Connect. In this case, theoperation and
specifications of the remotedevice may differ from the description
inthis manual.
If pairing and the BLUETOOTH connection
fail, do the following. Relaunch NFC Easy Connect and move
the remote device slowly over theN-Mark.
Remove the case from the remote deviceif using a commercially
available remotedevice case.
To listen to music
Start playback of an audio source on the
remote device. For details on playbackoperations, refer to the
operatinginstructions of your remote device.
If the volume level is low, adjust thevolume of the remote
device first. If thevolume level is still too low, adjust thevolume
level on the main unit.
To stop playbackThe playback will be stopped when youperform any
of the following items. Hold the remote device near to the
N-Mark on the main unit again. Stop the music player of the
remote
device. Turn off the main unit or the remote
device. Change the function.
Disable the BLUETOOTH function onthe remote device.
By holding a One-touch mirroring-
compatible Xperia near to the N-Markon the main unit, you can
wirelesslymirror your entire Xperia smartphonescreen on a big
screen TV. You canwatch videos or browse together withyour family
and friends. No wirelessrouter (or access point) is required touse
this function.
Note
Note
Tip
Tip
Connecting to an Xperiasmartphone by One-touchmirroring function
(NFC)
Compatible Xperia smartphonesXperia with the One-touch
mirroringfunction
-
8/11/2019 bdv 7200 en
38/84
-
8/11/2019 bdv 7200 en
39/84
-
8/11/2019 bdv 7200 en
40/84
40GB
To play remote files by operatingthe system (Renderer) via a
DLNAcontroller
You can operate the system with aDLNA-certified controller (a
mobilephone, etc), when playing files stored
on a DLNA server.
For details on operation, refer to theoperating instructions of
the DLNAcontroller.
Do not operate the system with thesupplied remote control and a
DLNA
controller at the same time.
The system is compatible with the PlayTo function of Windows
Media Player 12that comes standard with Windows 7.
You can acquire content informationusing Gracenote technology
and searchfor related information.
1 Connect the system to a network(page 25).
2 Insert a disc with content aboutwhich you want to search.
You can perform a video searchfrom a BD-ROM or DVD-ROM, and
amusic search from a CD-DA (musicCD).
3 Press B/bto select [Video] or[Music].
4 Press V/vto select [VideoSearch] or [Music Search].
The content information (such as
title, cast, track, or artist), [PlaybackHistory] and [Search
History] aredisplayed. [Playback History]
Displays a list of previously playedBD-ROM/DVD-ROM/CD-DA(music
CD) titles. Select a title toacquire content information.
[Search History]Displays a list of previous searches
performed via the [Video Search]or [Music Search] function.
To search for further relatedinformation
Select an item in the lists, then select theservice for
searches.
TV SideView is a free mobile applicationfor the remote device
(smartphone, etc).By using the TV SideView with thissystem, you can
easily enjoy the systemby the operation on your remote device.You
can launch a service or applicationdirectly from the remote device
andview the disc information during the
disc playback. The TV SideView also canbe used as a remote
control andsoftware keyboard.Before you use the TV SideView
devicewith this system for the first time, besure to register the
TV SideView device.Follow the on-screen instructions on theTV
SideView device for registration.
The registration will be possible only whenhome menu appears on
the TV screen.
Note
Tip
Searching for video/musicinformation
Controller
Renderer(This system)Server
Using the TV SideView
Note
-
8/11/2019 bdv 7200 en
41/84
41GB
Playback
Available Options
Various settings and playbackoperations are available by
pressingOPTIONS. The available items differ
depending on the situation.
Common options
[Video] only
[Sound Field]Changes the sound field setting(page 29).
[Cinema Studio 9.1ch]Turns on or off the Cinema Studio 9.1
channelmode (page 30).
[Music Arena]Turns on or off the Digital Music Arena mode(page
30).
[Philharmonic Hall]Turns on or off the Philharmonic Hall
mode(page 30).
[Football]Selects the football mode (page 31).
[Repeat Setting]Sets repeat playback.
[3D Menu][Simulated 3D]: Adjusts the simulated 3D
effect.[3D Depth Adjustment]: Adjusts the depth of3D images.[2D
Playback]: Sets playback to 2D image.
[Play/Stop]Starts or stops playback.
[Play from start]Plays the item from the beginning.
[Change Category]Switches among the [Video], [Music]
and [Photo] category in BD/DVD (for disc
only), USB function or DLNA server. This item
only available when the display list is available
for the category.
[A/V SYNC]Adjusts the time gap between picture andsound (page
42).
[3D Output Setting]Sets whether or not to output 3D video
automatically.
Note
3D video from the HDMI (IN 1) or HDMI (IN 2)jack is output
regardless of this setting.
[Video Settings][Picture Quality Mode]: Selects the
picturesettings ([Direct], [Brighter Room], [TheatreRoom], [Auto],
[Custom1] and [Custom2]).
You can customize the following picture
settings according to your preference andsaved them in
[Custom1]/[Custom2] settings. [Texture Remaster]: Adjusts the
sharpness
and detail of the edges. [Super Resolution]: Improves the
resolution. [Smoothing]: Reduces on-screen banding by
smoothing gradations on flat areas. [Contrast Remaster]:
Automatically arranges
the black and white levels so that the screenis not too dark and
the image is modulated.
[Clear Black]: Adjusts the display of the darkelements of the
image. All shading is not
suppressed; it allows beautifully reproducedblack tones.
[Pause]Pauses playback.
[Top Menu]Displays the BDs or DVDs Top Menu.
[Menu/Popup Menu]Displays the BD-ROMs Pop-up Menu or
DVDsmenu.
[Title Search]Searches for a title on BD-ROMs/DVD VIDEOsand
starts playback from the beginning.
[Chapter Search]Searches for a chapter and starts playbackfrom
the beginning.
[Audio]Selects the audio format/track.
[Subtitle]Selects the subtitle language whenmultilingual
subtitles are recorded onBD-ROMs/DVD VIDEOs.
[Angle]Switches the viewing angles when multi-angles are
recorded on BD-ROMs/DVDVIDEOs.
-
8/11/2019 bdv 7200 en
42/84
42GB
[Music] only
[Photo] only
(A/V SYNC)
When the sound does not match the
pictures on the TV screen, you canadjust the delay between the
pictureand sound for the following functions.The setting method
differs dependingon the function.
When the BD/DVD, USB,HDMI1 or HDMI2 function isselected
1 Press OPTIONS.The option menu appears on the TVscreen.
2 Press V/vto select [A/V SYNC],then press .
3 PressB/bto adjust the delay, thenpress .
You can adjust from 0 ms to 300 ms
in 25 ms increments.
When the TV function isselected
1 Press OPTIONS.AV.SYNC appears in the top paneldisplay.
2 Press or b.
3 PressV/vto adjust the delay, thenpress .
You can adjust from 0 ms to 300 msin 25 ms increments.
4 Press OPTIONS.The option menu in the top paneldisplay turns
off.
[IP Content NR Pro]Adjusts the video quality for Internet
content.
[Video Search]Displays information on the BD-ROM/DVD-ROM based
on Gracenote technology.
[Number Entry]Inputs numbers. Use B/V/v/bto select the
number.
[Track Search]Searches the track number during music
CDplayback.
[Add Slideshow BGM]Registers music files in the USB memory
asslideshow background music (BGM).
[Music Search]Displays information on the audio CD(CD-DA) based
on Gracenote technology.
[Visualizer]/[Colour Pattern]Changes the visualizer color effect
on the TVscreen (page 50).
[Slideshow]
Starts a slideshow.[Slideshow Speed]Changes the slideshow
speed.
[Slideshow Effect]Sets the effect when playing a slideshow.
[Slideshow BGM] [Off]: Turns off the function. [My Music from
USB]: Sets the music files
registered in [Add Slideshow BGM]. [Play from Music CD]: Sets
the tracks on
CD-DAs.
[Change Display]Switches between [Grid View] and [List
View].
[Rotate Left]Rotates the photo counterclockwise by90
degrees.
[Rotate Right]Rotates the photo clockwise by 90 degrees.
[View Image]Displays the selected picture.
Adjusting the delay betweenthe picture and sound
-
8/11/2019 bdv 7200 en
43/84
-
8/11/2019 bdv 7200 en
44/84
-
8/11/2019 bdv 7200 en
45/84
45GB
Tuner/Othe
rOperations
Each time you press DISPLAY, the display inthe top panel display
changes cyclically asfollows:FrequencytPreset
numbertDecodingstatus*
* Appears when [Sound Effect] is set to[Dolby Pro Logic], [DTS
Neo:6 Cinema], or[DTS Neo:6 Music] (page 59).
Receiving Radio DataSystem (RDS)
(Europe models only)The system offers RDS feature whichenables
you to view additionalinformation from radio stations.
Simply select a station from the FM
band.
The station name appears on the TVscreen.
RDS may not work properly if the stationyou are tuned to is not
transmitting theRDS signal properly, or if the signalstrength is
weak.
Not all FM stations provide RDS service,nor do they provide the
same type ofservices. If you are not familiar with theRDS system,
check with your local radio
stations for details on RDS services in yourarea.
Using the Control for
HDMI Function forBRAVIA Sync
This function is available on TVs with theBRAVIA Sync
function.By connecting Sony equipment that iscompatible with the
Control for HDMIfunction via an HDMI cable, operation
issimplified.
To use the BRAVIA Sync function, be sureto turn on the system
and all connectedequipment after completed the HDMIconnection.
Control for HDMI - Easy Setting
You can set the systems [Control forHDMI] function automatically
by
enabling the corresponding setting onthe TV.For details about
the Control for HDMIfunction, see [HDMI Settings](page 60).
System Power Off
You can turn the system off in sync withthe TV.
The system does not turn off automaticallywhile playing music or
when FM functionis selected.
One-Touch Play
When you press Non the remotecontrol, the system and TV turn on,
andthe TVs input is switched to the HDMI
input which the system is connected.
Tip
Note
Other Operations
Note
Note
-
8/11/2019 bdv 7200 en
46/84
46GB
System Audio Control
You can enjoy the sound from TV orother equipment by a simple
operation.
You can use the System Audio Controlfunction as follows: When
the system is turned on, the
sound of the TV or other equipmentcan be output from the
speakers of thesystem.
When sound from the TV or otherequipment is output via the
speakersof the system, you can switch thesound to output from the
TV speakersby pressing SPEAKERS TVyAUDIO.
When sound from the TV or otherequipment is output via the
speakersof the system, you can adjust thevolume and turn off the
sound of thesystem by operating the TV.
Audio Return Channel
You can enjoy TV sound via the systemby using just one HDMI
cable. For detailsof the setting, see [Audio ReturnChannel] (page
61).
Language Follow
When you change the language for theon-screen display of the TV,
thesystems on-screen display language isalso changed after turning
off and onthe system.
Routing Control
When you perform One-Touch Play onthe connected equipment, the
systemturns on and sets the systems functionto HDMI1 or HDMI2
(depending onthe HDMI input jack in use), and yourTVs input is
automatically set to theHDMI input to which the system
isconnected.
Calibrating theAppropriate SpeakerSettings Automatically
[Auto Calibration]
(BDV-N9200W/BDV-N9200WL/
BDV-N7200W/BDV-N7200WL
only)
D.C.A.C. DX (Digital Cinema AutoCalibration DX) brings you the
idealsound experience by automaticallyadjusting the setting of the
speakers
distance, location, and acoustic.
The system outputs a loud test soundwhen [Auto Calibration]
starts. Youcannot turn the volume down. Giveconsideration to
children and neighbors.
Before [Auto Calibration], make sure that all the speakers are
connected to the
main unit and surround amplifier. the surround amplifier is
turned on and
you have installed the surroundamplifier in an appropriate
location toensure wireless connection with it.
1 Press HOME.The home menu appears on the TVscreen.
2 Press B/bto select [Setup].
3 Press V/vto select [AudioSettings], then press .4 Press V/vto
select [Auto
Calibration], then press .
The [Select speaker layout.] displayappears.
Note
-
8/11/2019 bdv 7200 en
47/84
47GB
OtherOperations
5 Press V/vto select settingaccording to your speakers
placement, then press .
[Standard]: The surroundspeakers are installed in the
rearposition.
[All Front]: All speakers areinstalled in the front
position.
The confirmation display for [AutoCalibration] appears.
6 Connect the calibration mic to theA.CAL MIC jack on the rear
panel.
Set up the calibration mic at earlevel using a tripod, etc.
(not
supplied). The calibration micshould aim the TV screen. The
frontof each speaker should face thecalibration mic, and there
should beno obstruction between thespeakers and the calibration
mic.
7 Press V/vto select [OK].To cancel, select [Cancel].
8 Press .[Auto Calibration] starts.The system adjusts the
speakersettings automatically.Be quiet during the measurement.
While [Auto Calibration] is in progress,do not operate the
system.
9 Confirm the result of [AutoCalibration].The distance and level
for eachspeaker appear on the TV screen.
If measurement fails, follow themessage then retry
[AutoCalibration].
If no center speaker is detected, the[Centre Speaker] will
be
automatically set to [Off].
10 Press V/vto select [OK] or[Cancel], then press .
x The measurement is OK.Disconnect the calibration mic,
thenselect [OK]. The result is
implemented.x The measurement is not OK.Follow the message, then
select[OK] to retry.
Setting the Speakers
[Speaker Settings]To obtain optimum surround sound, setthe
speakers distance from yourlistening position.
1 Press HOME.The home menu appears on the TVscreen.
2Press B/bto select [Setup].
3 Press V/vto select [AudioSettings], then press .
4 Press V/vto select [SpeakerSettings], then press .
The [Select speaker layout.] displayappears.
5 Press V/vto select settingaccording to your speakersplacement,
then press .
[Standard]: The surroundspeakers are installed in the
rearposition.
[All Front]: All speakers areinstalled in the front
position.
All settings are reset to default
settings each time you change thespeaker layout setting.
Note
Note
Note
-
8/11/2019 bdv 7200 en
48/84
48GB
6 Press B/bto select [OK] or[Cancel], then press .
7 Press V/vto select the item, thenpress .
8 PressV/vto adjust the parameter.9 Press B/band to confirm
the
settings.
Check the following settings.
x [Centre Speaker]
[On]: The center speaker is connected.[Off]: The center speaker
is notconnected.
x [Distance]
When you move the speakers, be sureto set the parameters of the
distancefrom the listening position to thespeakers.You can set the
parameters from 0.0 to7.0 meters.
[Front Left/Right] 3.0 m: Set the frontspeaker distance.[Centre]
3.0 m: Set the center speakerdistance. This setting is only
availablewhen [Centre Speaker] is set to [On].[Surround Left/Right]
3.0 m: Set thesurround speaker distance.[Subwoofer] 3.0 m: Set the
subwooferdistance.
x [Level]You can adjust the sound level of thespeakers. You can
set the parametersfrom 6.0 dB to +6.0 dB. Be sure to set[Test Tone]
to [On] for easy adjustment.
[Front Left/Right] 0.0 dB: Set the frontspeaker level.[Centre]
0.0 dB: Set the center speakerlevel. This setting is only available
when
[Centre Speaker] is set to [On].[Surround Left/Right] 0.0 dB:
Set thesurround speaker level.
[Subwoofer] 0.0 dB: Set the subwooferlevel.
x [Relocation] (BDV-N9200W/
BDV-N9200WL/BDV-N7200W/
BDV-N7200WL only)
You can correct the speaker positionvirtually to improve the
surround effect.
[On]: You can hear sound from avirtually relocated speaker
positiondetermined by [Auto Calibration].[Off]: You can hear sound
from theactual speaker position.
This setting is only reflected afterperforming [Auto
Calibration]. You cannot select this function when the
speaker layout is set to [All Front].
x [Test Tone]
The speakers will emit a test tone toadjust [Level].
[Off]: The test tone is not emitted from
the speakers.[On]: The test tone is emitted from eachspeaker in
sequence while adjustinglevel. When you select one of the[Speaker
Settings] items, the test tone isemitted from each speaker in
sequence.Adjust the sound level as follows.
1 Set [Test Tone] to [On].
2 PressV/vto select [Level], then press.
3 Press V/vto select the speaker typeyou want, then press .
4 Press B/bto select the left or rightspeaker, then press V/vto
adjust the
level.
5 Press .
6 Repeat Steps 3 to 5.
Note
-
8/11/2019 bdv 7200 en
49/84
49GB
OtherOperations
7 Press RETURN.The system returns to the previousdisplay.
8 Press V/vto select [Test Tone], thenpress .
9 Press V/vto select [Off], then press.
The test tone signals are not output fromthe HDMI (OUT)
jack.
The test tone is not emitted from thecenter speaker if [Centre
Speaker] is set to[Off].
To adjust the volume of all the speakers atthe same time, press
2+/.
Using the Sleep Timer
You can set the system to turn off at a
preset time, so you can fall asleeplistening to music.
Press SLEEP.
Each time you press SLEEP, the minutesdisplay (the remaining
time) in the toppanel display changes by 10 minutes.
When you set the sleep timer, theremaining time appears
every
5 minutes.When the remaining time is less than2 minutes, SLEEP
flashes in the toppanel display.
To check the remaining time
Press SLEEP once.
To change the remaining time
Press SLEEP repeatedly.
Deactivating the Buttonson the Main Unit
(Child Lock)
You can deactivate the buttons on themain unit (except for "/1)
for preventingmisoperation, such as child mischief.
Touch and hold xon the main unit formore than 5 seconds.LOCKED
appears in the top paneldisplay.The child lock function is
activated andthe buttons on the main unit are locked.
(You can operate the system by usingthe remote control.)To
cancel, touch and hold xfor morethan 5 seconds until UNLOCK
appearsin the top panel display.
Changing the Brightness
You can change the brightness of thefollowing items:
Illumination LED on the speakers
(BDV-N9200WL/BDV-N7200WL only) Top panel display Indicator of
the soft-touch buttons LED indicator on the top panel
Press DIMMER.
Each time you press the button, thebrightness of the item is
changed.You can adjust the brightness in3 levels.*
* For top panel display, the brightness for[Dimmer : 1], [Dimmer
: 2] and[Dimmer : 3] settings are the same.
You can adjust the brightness of the
Illumination LED on the speakers evenwhen the main unit is
turned off. Be sure toturn on the speaker illuminationbeforehand
(page 51).
Note
Tip
Tip
-
8/11/2019 bdv 7200 en
50/84
50GB
Enjoying theVisualization on the TVScreen
You can enjoy the visualizer effectwhich simulates the beat of
the playedback sources to the colorful designs andgraphics. You can
stream the effectsduring music playback (only forBD/DVD, USB, FM,
TV, BT andAUDIO functions) and built-in sounddemonstration.
Press VISUALIZER repeatedly.(BDV-N9200W/BDV-N7200W/
BDV-N5200W only)
Press COLOUR PATTERN repeatedly.
(BDV-N9200WL/BDV-N7200WL only)
The visualization appears on the TVscreen and synchronizes with
the beatof the music. Each time you press thebutton, the color
effect changes
cyclically as follows:
[RAINBOW]t[PASSION]t[OCEAN]t[FOREST]t[Off]
The visualizer effect may becomeunsmooth when you play back High
BitrateAudio content more than 15 Mbps.
To avoid the information appears on theTV screen and overlaps
with thevisualization, set [Auto Display] in[System Settings] to
[Off] (page 61).
You can also select the visualizer effect byusing the option
menu.
Enjoying SpeakerIllumination
(BDV-N9200WL/BDV-N7200WL
only)You can experience a more REALimmersive feeling just like
you are in astadium, live stage or inside the movieby turning on
the illumination on thespeakers. You can select the front
andsurround speakers illumination patternaccording to your
preference.
The illumination LED light is bright, be sureto avoid looking
directly at the LED light. Ifthe illumination is glaring, you can
turn offthe speaker illumination or adjust thebrightness of the
illumination LED(page 49).
We recommend you to use the speakersunder the following
conditions.
Place the speakers about 0.5 meter awayfrom the wall.
Better illumination effect when placed infront of a
brightly-colored wall.
Press SPEAKER ILLUMINATION
repeatedly.
Note
Tip
Note
Tip
IMMERSIVE[Immersive Colour]
During video playback, the illumination colorchanges depending
on the color of the TVscreen.During music playback or photo play
(withMP3 files are played back), the illuminationcolor changes
depending on thevisualization color (page 50)andsynchronizes with
the beat of the music.During photo play (MP3 files are not
playedback), the lighting color is blue.
AMBIENT
[Ambient Colour]The illumination LED lights up in blue.
-
8/11/2019 bdv 7200 en
51/84
51GB
OtherOperations
When the main unit is turned off
You can press SPEAKER ILLUMINATIONto turn on or off the
illumination LED ofthe front speakers. The illumination LEDlights
up in blue.
Saving Power in Standby
ModeCheck that you have made the followingsettings: [Control for
HDMI] in [HDMI Settings] is
set to [Off] (page 60). [Quick Start Mode] is set to [Off]
(page 61). [Remote Start] is set to [Off] (page 63). [NFC] is
set to [Off] (page 61).
Browsing Websites
1 Prepare for Internet browsing.Connect the system to a
network(page 25).
2 Press HOME.The home menu appears on the TVscreen.
3 Press B/bto select [Network].4 Press V/vto select
[Internet
Browser], then press .
The [Internet Browser] display
appears.
Some websites may not display correctly,or not function.
To enter a URL
Select [URL entry] from the optionsmenu.Enter the URL using the
software
keyboard, then select [Enter].
To set the default start page
While the page you want to set isdisplayed, select [Set as start
page] fromthe options menu.
To return to the previous page
Select [Previous page] from the options
menu.When the previous page does notappear even if you select
[Previouspage], select [Window List] from theoptions menu and
select the page youwant to return to from the list.
To quit Internet Browser
Press HOME.
REAR IMMERSIVE OFF[Immersive Colour (Rear Off)]The illumination
of the surround speakers areturned off. The illumination pattern of
thefront speakers is same as [Immersive Colour]setting.
REAR AMBIENT OFF
[Ambient Colour (Rear Off)]The illumination of the surround
speakers areturned off. The illumination pattern of thefront
speakers is same as [Ambient Colour]setting.
OFF[Off]The illumination of all speakers are turnedoff.
Note
-
8/11/2019 bdv 7200 en
52/84
52GB
You can check website information bypressing DISPLAY. The
displayinformation differs depending on thewebsite and page
status.
A Page title
B Page address
C CursorMove by pressing B/V/v/b. Place
the cursor on the link you want to
view, then press . The linked
website is displayed.
D SSL iconAppears when the linked URL is
secured.
E Signal strength indicatorAppears when the system is
connected to a wireless network.
F Progress bar/Loading iconAppears when the page is being
read, or during file download/
transfer.
G Text input fieldPress , then choose [Input] from
the options menu to open the
software keyboard.
H Scroll barPress B/V/v/bto move the page
display left, up, down, or right.
Various settings and operations areavailable by pressing
OPTIONS.The available items differ depending onthe situation.
Internet Browser display Available options
[Browser Setup]Displays the Internet
