Automation and Network Solutions EtherNet/IP Profile Switch Sales Presentation

Automation and Network Solutions

EtherNet/IP Profile SwitchSales Presentation


OpenRail One platform, one thousand possibilities

OpenRail One platform, one thousand possibilities


Open Rail Overview

Managed switch family – available as RS (rail switch) or MS (modular switch)

Rail Switches available with 4, 8, 16 or 24 ports

• RS20 – all ports are 10/100mbps• RS30 – 2 additional gigabit ports

(total of 10, 18 or 26 ports)• RS40 – all gigabit ports

Modular Switches available with8, 16 or 24 ports

• MS20 – all ports are 10/100mbps• MS30 – adds 1 slot for 2 gigabit

ports (total of 10, 18 or 26 ports)• Many different media modules

available


What is the EtherNet/IP Profile Switch?

A new firmware (version 3.0) puts EtherNet/IP functionality into all managed Open

Rail switches (RS20/30/40 and MS20/30)

Functionally, nothing in the switch changes – this is just an added feature

This allows users to integrate the switch directly into the RSLogix5000 I/O tree

This makes it much easier for customers to configure and monitor their managed

switches

Integrating this information into an HMI is easier than ever before

Generating network alarms becomes simple

All existing Open Rail switches can be flashed up to this firmware level (send an e-

mail to [email protected])

Nothing special to order – it’s embedded in every switch

Available in March

Sample files for RSLogix5000 and RSView Studio can be found at

http://samplecode.rockwellautomation.com(search Title – Hirschmann) or at

ftp.hirschmann-usa.com/EthernetIP


Screenshot from RSLogix5000 sample

file

Hirschmann Add-On Instruction

(v16 required)

Switches in the I/O tree


Screenshots from sample RSView Studio file

Main switch screen

Templates are available for

various switches

Diagnostics screen


Switch information screen

IGMP Config screen

Port Enable/Disable

screen

Port information screen


One more thing…

It’s free!

There is no additional cost for this functionality. If you buy the switch, it’s

there. If you already have a switch, just download and install the firmware.


Available Resources

Sample files• http://samplecode.rockwellautomation.com (Search Title –

Hirschmann)• ftp.hirschmann-usa.com/EthernetIP

EtherNet/IP Step by Step presentation


Additional Technical Information

3.1 release (June) will add support for MACH, PowerMICE and Octopus switch families

Other protocols are supported• ProfiNet at 3.0 release• ModBus TCP – future release

Sample files make use of the Add-On Instruction feature in RSLogix5000, which requires version 16

Version 16 is not required for the EtherNet/IP functionality to work – only to take advantage of our samples


Another New Offering: -E Firmware

-E is ideal for customers who want some features of managed switches (IGMP Snooping, etc.) but don’t want to have to configure the switch

A switch with –E firmware has different factory default settings so that it can be installed in most EtherNet/IP applications with no configuration

Good for small, isolated networks All management features are still available, -E just changes

some factory defaults so management may not be required


-E Settings

These settings are factory default for the –E firmware • IGMP Snooping – Enabled (version 2)• IGMP Querier Mode – Enabled• EtherNet/IP – Enabled• IP address via DHCP• Address Conflict Detection – On• Dip switches are physically set so that they are disabled (all

configuration done via software)• RSTP – Off• All TX ports set to Autonegotiate

***These are the settings that are changed from standard factory default***


Questions???

Documents

Automation and Network Solutions EtherNet/IP Profile Switch Sales Presentation