Austr TiLite Order Form V2 - seatingdynamics.com.au · TiLite® OF_AERO_T_0143RevB Effective anuary 1 2014 (New Items in Red) ALUMINUM RIGID FRAME Austr TiLite Order Form Page. 1

TiLite® OF_AERO_T_0143RevB

Effective January 1, 2014 (New Items in Red) ALUMINUM RIGID FRAME

Australian TiLite Order FormPage 1 of 7

ATFS1 ❑TiLite Aero T (Full Adjustability. 265 Pound (120kg) Weight Limit.)

TiFIT: TAILORED INDIVIDUALIZED FRAMESEAT WIDTH A Measure from outside of seat tube at back post to the outside of the opposite seat tube at back post.

ATSW1 ❑ 12” (30.5cm) ❑ 13” (33cm) ❑ 14” (35.5cm) ❑ 15” (38cm) ❑ 16” (40.5cm)❑ 17” (43cm) ❑ 18” (46cm) ❑ 19” (48cm)

ATSW2 ❑ 20” (51cm)

SEAT DEPTH B Measure from front of back post to the front edge of seat sling. Front edgeof seat sling will be .5”(1cm) behind bend at front of chair frame, unless Glide™ or a 90º Front Angle is ordered, in which case front edge of seat sling begins approximately 1” behind the bend.

ATSD1 ❑ 12” (30.5cm) ❑ 13” (33cm) ❑ 14” (35.5cm) ❑ 15” (38cm) ❑ 16” (40.5cm) ❑ 17” (43cm) ❑ 18” (46cm) ❑ 19” (48cm)

ATSD2 ❑ 20” (51cm). ATSD3 ❑ Custom Frame Depth: __________” Frame Depth Longer or Shorter Than Seat Depth

(A Custom Frame Depth of 20”(51cm) is $475.)

FRONT SEAT HEIGHT C Measure from floor to top of seat tube at beginning of bend. AERO T adjusts up and down in 1/2” (1cm) increments.

ATFSH1 ❑ 15” (38cm) ❑ 15.5” (39cm) ❑ 16” (40.5cm) ❑ 16.5” (42cm) ❑ 17” (43cm) ❑ 17.5” (44.5cm) ❑ 18” (46cm) ❑ 18.5” (47cm) ❑19” (48cm) ❑ 19.5” (49.5cm) ❑ 20” (51cm) ❑ 20.5” (52cm) ❑ 21” (53cm)

REAR SEAT HEIGHT D Measure from floor to top of seat tube at back post. AERO T adjusts up and down in 1/2” (1cm) increments.

ATRSH1 ❑ 13” (33cm) ❑ 13.5” (34cm) ❑ 14” (35.5cm) ❑ 14.5” (37cm) ❑ 15” (38cm) ❑ 15.5”(39cm) ❑ 16” (40.5cm)❑ 16.5” (42cm) ❑ 17” (43cm) ❑ 17.5” (44.5cm) ❑ 18” (46cm) ❑ 18.5” (47cm)❑ 19” (48cm) ❑ 19.5” (49.5cm) ❑ 20” (51cm) ❑ 20.5” (52cm) ❑ 21” (53cm)

REAR SEAT HEIGHT RANGES

20” (451)22” (501)24” (540)25” (559)26” (590)

Rear Wheel Size Rear Seat Height

13”- 19” (33-48cm)14”- 20” (35.5-51cm)15”- 21” (38-53cm)15.5”- 21” (39-53cm)15.5”- 21” (39-53cm)

SEAT TO Footrest E/Footrests Measure from front edge of seat sling to top rear of Footrest.

STANDARD FOOTRESTS Measurement must be at least 2” (5cm) shorter than Front Seat Height C.❑ 13.5” (34cm) ❑ 14” (35.5cm) ❑ 14.5” (37cm) ❑ 15” (38cm) ❑ 15.5” (39cm) ❑ 16” (40.5cm) ❑ 16.5” (42cm) ❑ 17” (43cm) ❑ 17.5” (44.5cm) ❑ 18” (46cm)❑ 18.5” (47cm) ❑ 19” (48cm)

ATFTR3 ❑ Angle Adjustable Footrest ATFTR1 ❑ Titanium Footrest w/Flat ABS Cover ATFTR2 ❑ Titanium Open Loop Footrest ATFTR12 ❑ Titanium Flip-Back Footrest (Not available with ABS Cover with 2” (5cm)

Sides or Front Roller.)

HIGH MOUNT FOOTRESTS ❑ 7” - 9” (18cm-23cm) ❑ 9” - 11” (23cm-28cm) ❑ 11” - 13” (28cm-33cm) Set at___________(Use 1/2” increments)

ATFTR4 ❑ Angle Adjustable High Mount Footrest

ATFTR14 ❑ ABS Cover w/2” (5cm) Sides (Not available with Flip-Back Footrest.)

THE ULTIMATE RIDE.®

Seating Dynamics Pty LimitedUnit 3A / 6 Boundary RoadNORTHMEAD NSW 2152ph: 1300 845 483 | ph: 02 8838 3100 | fax: 02 9012 0087

THE TITANIUM EXPERTS.®

Please Email order to [email protected] or Fax 02 9012 0087

RTS: Phone:Email:SHIP TO INFORMATIONName: Ship Via:Address:City: State: Zip:Phone: Fax:

DEALER INFORMATION TiLite INFORMATIONClient Name:Dealer: PO:Contact No:

TiLite Information Promo Code:Ship Date: Order #:

V2




TiFIT: TAILORED INDIVIDUALIZED FRAME SEAT BACK TYPE/PUSH HANDLES/SEAT BACK HEIGHT F Measure from top of back post to top of seat tube at rear of frame.

SEAT BACK TYPE ATSB1 ❑ Folding Aluminum Adjustable Height ATSB2 ❑ Folding Titanium Adjustable Height with New Rounded Rigidizer Bar (Titanium back will match Frame Finish. Not available with Bolt-On Push Handles.)

TISHAFT™ BACK RELEASE BARS ATSB3 ❑ Aluminum ATSB4 ❑ Titanium ATSB5 ❑ Carbon Fiber

PUSH HANDLES ATSB6 ❑ Integrated Push Handles ATSB7 ❑ Integrated Fold-Down Push Handles (Requires Tension Adjustable by Straps Back Upholstery.) ATSB8 ❑ Bolt-On Push Handles (Requires 4” (10cm) Deep Backrest Rigidizer Bar. Not available with Ti Back.) ATSB9 ❑ Bolt-On Height-Adjustable Push Handles (Requires 4” (10cm) Deep Backrest Rigidizer Bar. Not available with Ti Back.)

SEAT BACK HEIGHT F

AVAILABLE ON ALL BACKS ATSB11 ❑ Backrest that Locks when Folded (Not available with .) ATSB12 ❑ 4” (10cm) Deep Backrest Rigidizer Bar (Not available with new Titanium Rounded Rigidizer Bar.) ATSB13 ❑ Custom Height Backrest Rigidizer Bar (The Standard Rigidizer Bar height is 5” (12.5cm) above the Seat Sling for a short, 6” (15cm) for a medium and 10” (25.5cm) for a tall. Custom Height Rigidizer Bar must be at least 4-1/2” (11.5cm) above Maximum Height is 3” (7.5cm) less than Lowest Seat Back Height.) Set at:___________(Use 1/4” increments.)

SEAT BACK ANGLE G Measure angle from front of back post to floor. ATSBA1 Folding Back ❑ 80° ❑ 83° ❑ 86° ❑ 89° ❑ 92° ❑ 95° ❑ 98° ❑ 101°

CENTER OF GRAVITY H Measure from front of back post at the seat tube to the center of the rear axle. If no center of gravity is selected, chair will ship with the center of gravity in the rearward-most position. ATCOG1 ❑ 1” (2.5cm) ❑ 1.25” (3cm) ❑ 1.5” (4cm) ❑ 1.75” (4.5cm) ❑ 2” (5cm) ❑ 2.25” (5.5cm) ❑ 2.5” (6 cm) ❑ 2.75” (7cm) ❑ 3” (7.5cm) ❑ 3.25” (8cm) ❑ 3.5” (9cm) ❑ 3.75” (9.5cm) ❑ 4” (10cm) ❑ 4.25” (10.5cm) ❑ 4.5” (11.5cm) ❑ 4.75” (12cm) ❑ 5” (12.5cm) ❑ 5.25” (13cm) ❑ 5.5” (14cm) ❑ 5.75” (14.5cm) ❑ 6” (15cm) ATAMP1 ❑ Amputee Adapter (Available in Black anodize only.)

FRONT SEAT WIDTH (SEAT TAPER) T Measure from inside of front frame tube to inside of opposite front frame tube. ATFSW1 ❑ No Taper (2” (5cm) Narrower than Rear Seat Width A.) ATFSW2 ❑ 1” (2.5cm) Taper (3” (7.5cm) Narrower than Rear Seat Width A. Includes Tension Adjustable by Straps Seat Upholstery.) ATFSW4 ❑ 2” (5cm) Taper (4” (10cm) Narrower than Rear Seat Width A. Includes Tension Adjustable by Straps Seat Upholstery.) ATFSW6 ❑ 3” (7.5cm) Taper (5” (12.5cm) Narrower than Rear Seat Width A. Includes Tension Adjustable by Straps Seat Upholstery.)

Push Handles (Selected Above) Short Medium Tall Set at: (Use 1/2” increments)

None / Bolt-On ❑ 8.5”- 11.5” (21.5-29cm) ❑ 12”- 16.5” (30.5-42cm) ❑ 16.5”- 20.5” (42-52cm) Set at:__________Integrated ❑ 10.5”- 12.5” (26.5-32cm) ❑ 13.5”- 16.5” (34-42cm) ❑ 17.5”- 20.5” (44.5-52cm) Set at:__________Integrated Fold-Down ❑ 13”- 15.5” (33-39cm) ❑ 14.0”- 18.5” (35.5-47cm) ❑ 18.5”- 21” (47-53cm) Set at:__________




TiFIT: TAILORED INDIVIDUALIZED FRAME FOOTREST WIDTH I Select a Standard Front End below. ATFE1 STANDARD FRONT END I Find your Rear Seat Width A in the chart below and select one of the options to the right. Measure from inside of front frame tube to inside of opposite front frame tube.

12” (30.5cm)13” (33cm)14” (35.5cm)15” (38cm)16” (40.5cm)17” (43cm)18” (46cm)19” (48cm)20” (51cm)

❑ 10” (25.5cm)❑ 11” (28cm)❑ 12” (30.5cm)❑ 13” (33cm)❑ 14” (35.5cm)❑ 15” (38cm)❑ 16” (40.5cm)❑ 17” (43cm)❑ 18” (46cm)

❑ 8” (20cm)❑ 9” (23cm)❑ 10” (25.5cm)❑ 11” (28cm)❑ 12” (30.5cm)❑ 13” (33cm)❑ 14” (35.5cm)❑ 15” (38cm)❑ 16” (40.5cm)

REAR SEAT WIDTH A(Outside Measurement)

No Taper(2” (5cm) Narrower

than Rear Seat Width)

2” Taper(4” (10cm) Narrower


4” Taper(6” (15cm) Narrower


❑ 8” (20cm)❑ 9” (23cm)❑ 10” (25.5cm)❑ 11” (28cm)❑ 12” (30.5cm)❑ 13” (33cm)❑ 14” (35.5cm)

FOOTREST WIDTH I

ATFE2 V-FRONT END V Measure from inside of front frame tube to inside of opposite front frame tube 2-1/2” (6cm) above Footrest. (Titanium Footrests have 1” (2.5cm) of adjustment up and down.)

❑NO V-Front Taper ❑ 8” (20cm) ❑ 8.5” (21.5cm) ❑ 9” (23cm) ❑ 9.5” (24cm) ❑ 10” (25.5cm) ❑ 10.5” (26.5cm) ❑ 11” (28cm) ❑ 11.5” (29cm) ❑ 12” (30.5cm) ❑ 12.5” (32cm) ❑ 13” (33cm) ❑ 13.5” (34cm) ❑ 14” (35.5cm) ❑ 14.5” (37cm) ❑ 15” (38cm) ❑ 15.5” (39cm) ❑ 16” (40.5cm) ❑ 16.5” (42cm) ❑ 17” (43cm) ❑ 17.5” (44.5cm)

REAR WHEEL SPACING J/PLUGS Measure from outside of seat back post to inside of rear tire. .5” Rear Wheel Spacing not available with 0° or 2° Camber K. ATRWS1 ❑ .75” (2cm) ❑ 1” (2.5cm) ❑ 1.25” (3cm) ❑ 1.5” (4cm) ❑ 1.75” (4.5cm) ❑ 2” (5cm) ATCBR9 ❑ Additional Spacers to Increase Rear Wheel Spacing ATCBR11 ❑Zero Play Aluminum Camber Plugs (Not available with more than 6° of Camber K.)

CAMBER K/CAMBER TUBES ATCBR1 ❑ 0° ❑ 2° ❑ 4° ❑ 6° ❑ 8° ❑ 12° (More than 6° of Camber K is not available with Zero Play Aluminum Camber Plugs or Carbon Fiber Camber Tube.) ATCBR2 ❑ 15° ❑ 18° ATCBR3 ❑ Titanium Camber Tube ATCBR6 ❑ Carbon Fiber Camber Tube (Not available with more than 6° of Camber K.) ATCBR5 ❑Additional Aluminum Camber Tube ATCBR4 ❑Additional Titanium Camber Tube ATCBR7 ❑Additional Carbon Fiber Camber Tube (Not available with more than 6° of Camber K.)

FRONT ANGLE L Measure from frame front to floor. ATFA1 ❑ 70° ❑ 80° ❑ 85° (Not available with 6” Front Wheels.) ❑ 90° (Not available with 5” or 6” Front Wheels.)

FRAME STYLE TILITE SPECIAL EDITIONS If selecting one of the TiLite Special Editions you must still fill out the entire order form. Edition options will override inconsistent selections. Options cannot be added or deleted.

ATP1 ❑ SuperLite Edition ATFTR2 Titanium Open Loop Footrest ATSB2 Folding Titanium Back ATSB5 Carbon Fiber TiShaft™ Back Release Bar ATCBR6 Carbon Fiber Camber Tube (Not available with a Power Adaptable Frame. When a Power Adaptable Frame is selected, a Aluminum Camber Tube will be used.). ATFK2 TiLite Slipstream Single-Sided Fork ATTS1 Titanium Fork Stems

ATRFR1 ❑ Reinforced Frame (Reinforced Frame required with a Power Assist or Power Add-on System. Not available with Carbon Fiber Camber tube or Slipstream Single-Sided Fork.) (No charge when 20” (51cm) Rear Seat Width A and 20” (51cm) Seat Depth B are selected.)

I

J

K

V

OR




FRAME FINISHES Natural Aluminum ATFF1 ❑ Light Satin (Finished with clear powder coat.) ATFF26 ❑ Satin ATSCBT ❑ Satin Finish Buffing Pads ATFF2 ❑ Polished Z2FF3 ❑Tattoos (Tattoos on front frame tubes. Frame finished in Satin. Click on the images below to view the Tattoos online.) $315

Z2FF31 ❑ The King of Rock Z2FF32 ❑Aloha

Z2FF33 ❑ Snow Leopard Z2FF34 ❑ Wood Grain

High Gloss Paint ATFF8 ❑ Super Wet Black ATFF9 ❑ Sunburst Yellow ATFF10 ❑ TiLite Red ATFF11 ❑ Military Green ATFF12 ❑ Orange Crush ATFF29 ❑ Neon Pink ATFF28 ❑ Neon Green Metallic Paint ATFF14 ❑ Ocean Blue Metallic ATFF15 ❑ Tangerine Metallic ATFF16 ❑ Salsa Red Metallic ATFF30 ❑ Acid Green Metallic Pearlescent Paint ATFF17 ❑Midnight Blue Pearl ATFF18 ❑ White Pearl Matte Paint ATFF19 ❑ Black Lava ATFF20 ❑ Deep Blue Ice ATFF27 ❑ Titanium Grey Candy Paint ATFF22 ❑ Ruby Red ATFF23 ❑ Azure Blue ATFF25 ❑ Electric Plum

COLOR ANODIZE PACKAGE (Color Anodize Package includes: Aluminum Camber Tube (Anodized Color not available with Power Adaptable Frame), Camber Clamp, Footrest Clamp and Caster Fork. If no anodize color is selected, the default will be black.) ATANO1 ❑ Black ATANO5 ❑ Sapphire ATANO3 ❑ Red Pepper ATANO6 ❑ Burnt Orange ATANO7 ❑ Sub-Lime ATANO8 ❑ Ultraviolet

CUSTOM CONFIGURATION OPTIONS FRONT WHEELS ATFW1 ❑ 3”x.75” Micro-Caster (Not available with Slipstream Fork.) ATFW2 ❑ 3”x.75” Light-Up Micro-Caster (Not available with Slipstream Fork.) ATFW24 ❑ 3”x1.5” LiteSpeed Billet Aluminum Wheel w/Soft Roll Tire ❑Silver Hub OR ❑Black Hub ATFW14 ❑ 4”x.75” Plastic Wheel w/Poly Tire (Not available with Slipstream Fork.) ATFW3 ❑ 4”x.75” Light-Up Micro-Caster (Not available with Slipstream Fork.) ATFW25 ❑ 4”x.75” LiteSpeed Billet Aluminum Wheel w/Poly Tire ❑Silver Hub OR ❑Black Hub ATFW26 ❏ 4”x1.5” LiteSpeed Plastic Wheel w/Soft Roll Tire ATFW27 ❑ 4”x1.5” LiteSpeed Billet Aluminum Wheel w/Soft Roll Tire ❑Silver Hub OR ❑Black Hub ATFW6 ❑ 5”x1” Plastic Wheel w/Poly Tire (Not available with 90º Front Angle L or Slipstream Fork.) ATFW28 ❏ 5”x1.5” LiteSpeed Plastic Wheel w/Soft Roll Tire (Not available with 90º Front Angle L.) ATFW29 ❑ 5”x.75” LiteSpeed Billet Aluminum Wheel w/Poly Tire ❑Silver Hub OR ❑Black Hub (Not available with 90º Front Angle L.) ATFW30 ❑ 5”x1.5” LiteSpeed Billet Aluminum Wheel w/Soft Roll Tire ❑Silver Hub OR ❑Black Hub (Not available with 90º Front Angle L.) ATFW9 ❑ 6”x1” Plastic Wheel w/Poly Tire (Not available with 85º or 90º Front Angle L or Slipstream Fork.) ATFW34 ❑ 6”x1” LiteSpeed Billet Aluminum Wheel w/Poly Tire ❑Silver Hub OR ❑Black Hub (Not available with 85º or 90º Front Angle L or Slipstream Fork.) ATFW31 ❑ 6”x1.25” LiteSpeed Billet Aluminum Wheel w/Pneumatic Tire ❑Silver Hub OR ❑Black Hub (Not available with 85º or 90º Front Angle L or Slipstream Fork.) ATFW32 ❑ 6”x1.5” LiteSpeed Plastic Wheel w/Soft Roll Tire (Not available with 85º or 90º Front Angle L or Slipstream Fork.) ATFW33 ❑ 6”x1.5” LiteSpeed Billet Aluminum Wheel w/Soft Roll Tire (Not available with 85º or 90º Front Angle L or Slipstream Fork.)

FRONT FORKS ATFK1 ❑ TiLite Standard Fork ATFK2 ❑ TiLite Slipstream Single-Sided Fork (Not available with Reinforced Frame.) ATGL1 ❑ Out-Front Glide® Suspension Forks (Black anodize only.) Rider’s Weight: ❑ 125 lbs (56.5kg). ❑ 125-180 lbs. (56.5-81.5kg) ❑ 180-265 lbs. (81.5-120kg) ATGL2 ❑ Out-Front Glide® Single-Sided Suspension Forks (Black anodize only.) Rider’s Weight: ❑ 125 lbs (56.5kg). ❑ 125-180 lbs. (56.5-81.5kg) ❑ 180-265 lbs. (81.5-120kg) ATTS1 ❑ Titanium Fork Stems




CUSTOM CONFIGURATION OPTIONS REAR WHEELS (See Rear Seat Height Ranges Chart on Page 1 for Rear Seat Height D limitations.) ATRW14 TiLite SHADOWTM (Not available with Titanium Quick Release Axles.) ❑ 20”(451) ❑ 22”(501) ❑ 24”(540) ❑ 25”(559) (Requires 15” (38cm) minimum Seat Depth B.) ❑ 26”(590) (Requires 15” (38cm) minimum Seat Depth B.) ATRW13 Golz TWIN-STAR Exchange (Not available with Titanium Quick Release Axles.) ❑ 24”(540) ❑ 25”(559) (Requires 15” (38cm) minimum Seat Depth B.) ❑ 26”(590) (Requires 15” (38cm) minimum Seat Depth B.) ATRW7 Spinergy SPOX ❑ Black ❑ Red ❑ Yellow ❑ Blue ❑ White ❑ 22”(501) - Std. Hub ❑ 24”(540) - Std. Hub ❑ 25”(559) - Std. Hub (Requires 15” (38cm) minimum Seat Depth B.) ❑ 26”(590) - Sport Hub (Requires 15” (38cm) minimum Seat Depth B. Not available with Titanium Quick Release or Quad Release Axles.) ATRW8 Spinergy LX ❑ Black ❑ Red ❑ Yellow ❑ Blue ❑ White ❑ Go Green ❑ Bright Orange ❑ Flamingo Pink ❑ 22”(501) - Std. Hub ❑ 24”(540) - Std. Hub ❑ 25”(559) - Std. Hub (Requires 15” (38cm) minimum Seat Depth B.)

❑ 26”(590) - Sport Hub (Requires 15” (38cm) minimum Seat Depth B. Not available with Titanium Quick Release or Quad Release Axles.) ATRW15 Topolino CarbonCore (Not available with Titanium Quick Release Axles or Solid Treaded Tires.) ❑ 24”(540) ❑ 25”(559) (Requires 15” (38cm) minimum Seat Depth B.) ATRW11 Mags (Not available with Short Tabs, Titanium Quick Release Axles, Quad Release Axles or Spoke Guards.) ❑ 22”(501) ❑ 24”(540) ATRW0 Omit Rear Wheels (Must choose Wheel Size below and Tire Type on page 6.) ❑ 20”(451) ❑ 22”(501) ❑ 24”(540) ❑ 25”(559) ❑ 26”(590)

AXLES ATAXL1 ❑ Stainless Quick Release ATAXL2 ❑ Titanium Quick Release (Not available with SHADOW, TWIN-STAR Exchange, 26”(590) Spinergy SPOX, 26”(590) Spinergy LX, Topolino CarbonCore, Mag Rear Wheels) ATAXL3 ❑ Quad Release (Not available with Mags or 26”(590) Spinergy Spox or LX Rear Wheels.)

PNEUMATIC REAR TIRES ATRAT1 ❑ Treaded (Not available with 25”(559) Rear Wheels.) ATRAT2 ❑ Airless Inserts (Not available with Topolino Rear Wheels.) ATRAT3 ❑ 25”(559) Primo Treaded (Standard with 25”(559) Rear Wheels.) ATRAT4 ❑ Primo ATRAT16 ❑ 20”(451) Kenda® Grey High Pressure (110psi) ATRAT5 24”(540), 25”(559) and 26”(590) Kenda® High Pressure (110psi) ❑ Grey ❑ Red ❑ Blue ATRAT6 ❑ 24”(540) Grey Knobby (Available with Shadow Rear Wheels Only.) ATRAT7 ❑ 26”(590) Black Knobby (Available with Shadow,Spinergy SPOX, or Spinergy LX Rear Wheels Only.) ATRAT8 ❑24”(540), 25”(559) and 26”(590) Schwalbe® Marathon Plus Evolution ATRAT17 ❑24”(540) and 25”(559) Speedrun SOLID REAR TIRES ATRAT10 ❑ 20”(451) Street Tread ATRAT11 ❑ 22”(501) Pyramid ATRAT18 ❑ 24”(540) and 25”(559) Herringbone Tread (Not available with Topolino Rear Wheels.) ATRAT15 ❏ 24”(540) and 25”(559) Treaded (Not available with Topolino Rear Wheels.)

HANDRIMS Handrims by OUT-FRONT® ATRIM1 ❑ Aluminum – Silver Anodized ATRIM21 ❑ Aluminum – Black Anodized Titanium (Not available with Mags, 20”(451) or 22”(501) Rear Wheels, or 24”(540) Knobby tires.) ATRIM12 ❏ Satin Finish ATRIM13 ❏ Polished Finish The Natural-Fit® (Original, Larger Profile) (Not available with 22”(501) Mags.) ATRIM14 ❑ Standard Grip (Not available with Short Tabs.) ATRIM15 ❑Super Grip (Not available with Short Tabs.) ATRIM16 ❑Without Thumb Grip The Natural-Fit® LT (Reduced Weight, Smaller Profile) (Not available with 22”(501) Mags.) ATRIM17 ❑ Standard Grip (Not available with Short Tabs.) ATRIM18 ❑Super Grip (Not available with Short Tabs.) ATRIM19 ❑Without Thumb Grip ATRIM10 ❑ The Surge (All-In-One Oval with Gription™ Strip, Larger Profile) (Not available with 22”(501) Mags.)




CUSTOM CONFIGURATION OPTIONS ATRIM11 ❑ The Surge LT (All-In-One Oval with Gription™ Strip, Smaller Profile) (Not available with 22”(501) Mags.) ATRIM20 ❑ Q-Grip (Exclusive High-Friction, Anti-Slip Coating) (Not available with 20”(451), Rear Wheels or Mags.) Additional Handrims ATRIM9 ❑Spinergy FlexRim (Available only on 24”(540) and 25”(559) Spinergy LX Rear Wheels. Please allow an additional 2-3 weeks delivery.) ATRIM5 ❑ Plastic Coated – Black ATRIM6 ❑ Projections - 8 Vertical Projections (Not available with 20”(451), 22”(501) or 26”(590) Rear Wheels or Mags.) ATRIM0 ❑ Omit Handrims Tab Length ATRIM7 ❑ Long Tabs ATRIM8 ❑ Short Tabs (Not available with Mags or The Natural-Fit® Handrims with Thumb Grip.)

WHEEL LOCKS Wheel Locks by OUT-FRONT® ATWLK7 ❑ Compact Composite Push to Lock (Available with .75” to 1.5” (2 to 4cm) Rear Wheel Spacing J only.) ATWLK8 ❑ Compact Composite Pull to Lock (Available with .75” to 1.5” (2 to 4cm) Rear Wheel Spacing J only.) ATWLK10 ❑ Extension Handles for Compact Composite Push/Pull to Lock ATWLK9 ❑ Composite Scissor Lock Additional Wheel Locks ATWLK3 Uni-Lock Set At: ❑ Push OR ❑ Pull ATWLK4 ❑ Extension Handles for Uni-Lock

BACK UPHOLSTERY ATBUP2 ❑ Velcro Adjustable (Not available with Fold-Down Push Handles.) Tension Adjustable by Straps (Required with Aluminum Fendered Side Guards and Fold-Down Push Handles.)

ATBUP3 ❑ Padded Nylon ATBUP5 ❑AIR Breathable Upholstery (Not available with Ultrasuede Backrest Stripe.) ATUPC3 Ultrasuede Backrest Stripe ❑ Black ❑ Sapphire ❑ Red Pepper ❑ Burnt Orange ❑ Sub-Lime ❑ Ultraviolet ❑ Espresso ATUPC3 ❑ TiLite NiteLite Reflective Backrest Stripe (Not available with AIR Breathable Back Upholstery.) ATBUP0 ❑ Omit Back Upholstery

SEAT UPHOLSTERY ATSUP1 ❑ Tension Adjustable Bolt On (Not available with a Tapered Seat T. Black only.) ATSUP7 ❑ iSleeve™ Under Seat Smartphone Holder (Not available with 12” (30.5cm) or 13” (33cm) Rear Seat Width A or Seat Depth B.) ATSUP2 ❑ Tension Adjustable by Straps (Standard with Front Seat Width Seat Taper T of 1” (2.5cm), 2” (5cm) or 3” (7.5cm). Black upholstery only.) ATSUP3 ❑ G10 Solid Seat (Not available with 10” (25.5cm) or 11” (28cm) Rear Seat Width A.) ATSUP0 ❑ Omit Seat Upholstery

SEAT CUSHIONS ATCSH1 Foam Cushion ❑ 2” (5cm) ❑ 3” (7.5cm) ❑ 4” (10cm)

SIDE GUARDS ATSDG1 ❑ Cloth (Not available with Ride Designs Corbac Back Support.) Aluminum ATSDG2 ❑Rigid Removable ❑ Small OR ❑ Std ATSDG3 ❑Quad Removable w/Hole ❑ Small OR ❑ Std ATSDG4 ❑Fold Down Rigid ❑ Small OR ❑ Std ATSDG6 ❑ Fendered Adjustable (Available with 24” and 25” Rear Wheels. Requires Rear Seat Height D of 15” to 18.5” (38cm to 47cm).) Carbon Fiber ATSDG7 ❑Rigid Removable ❑ Small OR ❑ Std ATSDG8 ❑Quad Removable w/Hole ❑ Small OR ❑ Std ATSDG9 ❑Fold Down Rigid ❑ Small OR ❑ Std ATSDG12 ❑ Fendered Removable Available on Aluminum and Carbon Fiber Non-Fendered Side Guards ATSDG13 ❑Side Guards Custom Cut to Profile of Rear Wheels (Not available with Cloth.)

ARMRESTS (Desk Arms come with built-in Side Guards.) ATARM1 Swing Away Tubular ❑ 9” to 12” (23-30.5cm) OR ❑ 11” to 14” (28-35.5cm) (Not Available with Height Adjustable Push Handles.) ATARM4 Swing Away - Flip Back Tubular ❑ 6” to 9” (15-23cm) OR ❑ 9” to 12” (23-30.5cm) ATARM2 Removable Height Adjustable Desk Arm with Rigid Side Guard (Requires 14” (35.5cm) minimum Seat Depth B.) ❑ Standard Length Pad (10” (25.5cm)) OR ❑ Full Length Pad (14” (35.5cm)) ❑ 9” to 12” (23-30.5cm) OR ❑ 12” to 15” (30.5-38cm) ATARM3 Removable Height Adjustable Desk Arm with Rigid Side Guard and Transfer Loop (Requires 15” minimum Seat Depth B.) ❑ Standard Length Pad (10” (25.5cm)) OR ❑ Full Length Pad (14” (35.5cm)) ❑ 9” to 12” (23-30.5cm) OR ❑ 12” to 15” (30.5-38cm) Available on all Armrests ATARM5 ❑ Covered in Black Ultrasuede




CUSTOM CONFIGURATION OPTIONS SEAT BELTS TWBLT1 ❑ Velcro Adjustable, Black Nylon Webbing NB205 ❑ Bodypoint® 2” (5cm) Push-Button Buckle (Auto-Style. Med & Large) HB205 ❑ Bodypoint® 1” (2.5cm) Wide Push-Button Buckle Padded (Auto-Style. Med & Large) HB205 ❑ Bodypoint® 1.5” (4cm) Wide Push-Button Buckle Padded (Auto-Style. Med & Large) HB215 ❑ Bodypoint® 1.5” (4cm) Wide Plastic Side Release Padded EB205 ❑ Bodypoint® Evoflex Pelvic Stabilizer HW320 ❑ Bodypoint® Optional Band Clamp Mounting Hardware ❑ XSmall ❑ Small ❑ Medium ❑ XLarge ❑ XLarge

CALF STRAP ATCLF2 Velcro Adjustable ❑ Xtra Small (Recommended for 6”- 9” (15-23cm) Footrest Widths) ❑ Small (Recommended for 9”- 12” (23-30.5cm) Footrest Widths) ❑ Medium (Recommended for 11”- 15” (28-38cm) Footrest Widths) ❑ Large (Recommended for 14”- 17” (35.5-43cm) Footrest Widths) ❑ Xtra Large (Recommended for 16”- 19” (40.5-48cm) Footrest Widths) ATCLF3 Bodypoint® Padded Velcro Adjustable ❑ Medium (Recommended for 12”- 15” (30.5-38cm) Footrest Widths) ❑ Large (Recommended for 16”- 20” (40.5-51cm) Footrest Widths) ATCLF1 ❑ Buckle Adjustable, Black Nylon Webbing

BACK PACK ATBCK1 ❑ Small - Black Nylon ATBCK2 ❑ Large - Black Nylon

SEAT POUCH ATPCH1 ❑ Small - SDL Bag ATPCH2 ❑ Large - Black Nylon

SPOKE GUARDS ATGRD1 ❑ Clear with TiMotion Logo (Not available with Mag Rear Wheels.) ATGRD2 ❑ Scooter Frog (Not available with Mag Rear Wheels.) ATGRD3 ❑ Color Spectrum (ROYGBIV) on Black (Not available with Mag Rear Wheels.) ATGRD4 ❑ Purple Party (Not available with Mag Rear Wheels.)

ANTI-TIPS ATTIP1 ❑ Rear Aluminum - Black ATTIP7 ❑ Black Aluminum Single Mount on ❑ Left Side or ❑ Right Side ATTIP2 ❑ User Friendly Rear Flip-Up ATTIP8 ❑ User Friendly Flip-Up Single Mount on ❑ Left Side or ❑ Right Side

ACCESSORIES ATUEST1Upper Extremity Support Tray ❑ 12” to 14” (30.5-36cm) OR ❑ 13” to 15” (33-38cm) Seat Widths A (Requires Armrests.) ATGS1 ❑ GRIP Solutions Lap Board ATLUG1 ❑ Luggage Carriers ATMPCT2 Neoprene Impact Guards with Ultrasuede Stripe ❑ Black ❑ Sapphire ❑ Red Pepper ❑ Burnt Orange ❑ Sub-Lime ❑ Ultraviolet ❑ Espresso ATMPCT2 ❑ TiLite NiteLite Neoprene Impact Guards with Reflective Stripe ATCAT1 ❑Catch-All ATCH1 ❑Crutch Holder ATHS1 ❑TiLite 9 Piece SAE Round Handle Folding Hex Key Set

DESIGNS UNLIMITEDTiLite’s 2GX offers hundreds of different frame combinations! But sometimes even that’s not enough. If you would like to customize your TiLite, check out the Designs Unlimited Studio at tilite.com. There you will find drawings and pricing for hundreds of creative solutions to customers’ customization requests. We call these “D.U.’s.” Designs Unlimited customization may add an additional 2 to 3 weeks to the ship time of your chair.

GENERALTiLite manufactures a wide variety of wheelchairs to meet the varied needs of wheelchair users. The final selection of a particular model, its options and accessories, and its measurements rests solely with the wheelchair user and advising healthcare professional. TiLite wheelchairs must be fitted by a qualified healthcare professional.

Get the latest order forms at tilite.com Prices, standard features, options and accessories are subject to change without notice. All rights reserved. Trademarks are identified by symbols™ and ®. TiLite, the TiLite logo, Ti, the Ti logo, The Titanium Experts, TiShaft and The Ultimate Ride are registered trademarks of TiSport, LLC. Adobe® , Acrobat®, Acrobat Professional® and Reader® are registered trademarks of Adobe Systems Inc. Bodypoint® is a registered trademark of Bodypoint Inc. Frog Legs® is a registered trademark of Frog Legs, Inc. Kenda® is a registered trademark of Kenda Rubber Industrial Co Ltd. Ride Designs® and Corbac® are registered trademark of Aspen Seating, LLC. ROHO®, Low Profile® and Quadtro Select® are registered trademarks of ROHO Inc. Schwalbe® is a registered trademark of Ralf Bohle GmbH. Supracor®, Stimulite® and Corbee® are registered trade-marks of Supracor, Inc. The Natural-Fit® is a registered trademark of Three Rivers Holdings, LLC. Varilite® is a registered trademark of Cascade Designs, Inc.

Documents

Austr TiLite Order Form V2 - seatingdynamics.com.au · TiLite® OF_AERO_T_0143RevB Effective anuary 1 2014 (New Items in Red) ALUMINUM RIGID FRAME Austr TiLite Order Form Page. 1