Upload
haquynh
View
235
Download
0
Embed Size (px)
Citation preview
Watch your fingers when adjusting clamps. They may become pinched resulting in injury.Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. May injure your fingers.
Before assembly, please make sure that all the items listed below are present.
Snare Pad x 1
Drum Key
Drumstick x 2
ASSEMBLY INSTRUCTIONS
Caution !
Inside This Package
[CYMBAL PADS] box
[DRUM PADS] box
[ACCESSORIES] box
Cymbal Pad x 2 [Hi-Hat Crash (Crash with choke) ]
Tom Pad x 3
Hexagon Key x4
Cymbal Holder (S)
Instruction Manual Assembly Instructions
AC Adaptor
Cymbal Pad x 1( Ride)
Cymbal Holder(L) _Left Cymbal Holder(L) _Right
[HI-HAT PEDAL] box
HI-Hat Control Pedal
Connection Cable X 9[DRUM MODULE] box
Drum Module
[PEDAL] box
Kick Pad
[BASS DRUM PEDAL] box
Foot Pedal
Beater
Assembly
Pillar(L1) Pillar(L2)
Side Arm(L1)Side Arm(L2)
Center Pipe( 2) Center Pipe(1)
Side Arm(R)
Pillar(R1)
Pillar(R2)
Clamp Clamp Clamp
Clamp Holder clamp
Cymbal holder clamp Holder clamp Holder clampHolder clamp
Cymbal holder clampCymbal holder clamp
Setting up the frame of the digital drum set [1] Loosen wing nut on the clamp. [2] Attach Center Pipe (1) to the clamp on the Pillar(L1). [3] Tighten wing nut on the clamp. [4] Loosen wing nut on the clamp. [5] Attach Center Pipe (2) to the clamp on the Pillar(L1). [6] Tighten wing nut on the clamp. [7] Loosen wing nut on the clamp. [8] Attach the Pillar(R1) to the Center Pipe (1) and Center Piper (2). [9] Tighten wing nut on the clamp.
Pillar (L1)
[1] [3]
[2] Center Pipe (1)
[5] Center Pipe (2)
[4] [6]
[10] Loosen wing nut on the clamp. [11] Attach the Side Arm (L1) to the clamp on the Pillar (L1) . [12] Tighten wing nut on the clamp.
[13] Loosen wing nut on the clamp. [14] Attach the Pillar (L2) to the Side Arm (L1) . [15] Tighten wing nut on the clamp.
[16] Loosen wing nut on the clamp. [17] Attach the Side Arm (R) to the clamp on the Pillar (R1) [18] Tighten wing nut on the clamp.
[19] Loosen wing nut on the clamp. [20] Attach the Pillar (R2) to the clamp on the Side Arm(R) . [21] Tighten wing nut on the clamp.
[22] Loosen wing nut on the screw on the clamp. [23] Attach the Side Arm (L2) to the clamp on the Pillar (L1). [24] Tighten wing nut on the clamp.
[7] [9]
[8]
Pillar (R1)Center Pipe (1)
Center Pipe (2)
[7] [9]
Pillar (L2)
[14]
[13] [15]
Pillar (L1)
[23]
[22] [24]
Side Arm(R)
[17]
[16] [18]
Pillar (R1)
Pillar (L1)
[11]
[10] [12]
Side Arm (L1)
Pillar (L1)
Side Arm(L1)
Pillar (R2)
[19],[21]
Side Arm(R)
Side Arm(L2)
[8]
[20]
Center Pipe(1)
Side Arm(R)
[1] Loosen wing nut on the holder clamp which is on the
center pipe(1) side arm(L2)and side arm(R) .
[2] Attach hexagon Key to the holder clamp on center pipe(1)
side arm(L2) side arm(R) .
[3] Tighten wing nuts.Repeat for each hexagon Key.
Attaching hexagon Key to rack
Wing Nut
Felt Washer
2 Attaching cymbals
[1] Remove wing nut and felt washer from cymbal tilter.
[2] Place cymbal pad on tilter assembly.
Re-attach the felt washer and wing nut. Tighten wing nut.
Cymbal Pad
Move Out
Wing Nut
Felt Washer
Side Arm(L1)
Pillar(L1)
Pillar(R1)
Ride
Hi-Hat
Crash[1]
[1]
[2]
[1] Loosen wing nuts on the drum pads.
[2] Attach drum pads to the hexagon Key on center pipe(1)
side arm(L2) side arm(R) and tighten wing nuts.
Repeat for each pad.
Attaching pads to rack
Holder Clamp Holder Clamp
Holder Clamp
Holder Clamp
Side Arm(L2)
[2]
[1],[3]
[1],[3]
[1],[3]
[1],[3]
[2]
[2]
[2]
Side Arm(R)
Center Pipe(1)
Side Arm(L2)
[2] [2]
[2][2]
Center Pipe(1)
Side Arm(R)
Side Arm(L2)
hexagon Key
hexagon Key
Attaching cymbals
[1] Loosen wing nut on the holder clamp on pillar(L1) pillar(R1) and side arm(L1) .[2] Insert each cymbal holder into pillar(L1) pillar(R1) side arm(L1) and tighten wing nuts.
1 Attaching cymbal holders
Side Arm(L1)
Pillar(L1)
Pillar(R1)
Cymbal Holder (S)
Cymbal Holder(L) _Left
[2][2]
[2]
[1] Loosen wing nut on the clamp which is on side arm(L1).
[2] Insert the drum module to the clamp .
[3] Tighten wing nut on the clamp .
Attaching module
Side Arm(L1)
[2]
[1],[3]
[1][1]
[1]
Cymbal Holder(L) _Right
Cymbal Holder(L) _Left Cymbal Holder(L) _Right
Wing Nut
Felt Washer
Cymbal Tilter
Cymbal Holder (S)
Wing Nut
Felt Washer
Move Out
[1]
Move Out
[1]
Cymbal Tilter
Cymbal Tilter
[1]
[1]
[2]
Beater
[5]
[6]
[3]
DD512_G02
Attaching the Kick Trigger
[1] Attach the Rod to the holders.
[2] Attach the Kick Pedal to the Kick Pad.
[3] Tighten the wing screw on the Kick Pedal.
[4] Loosen the screw.
[5] Attach the Beater to the Kick Pedal.
[6] Position the Beater from the center of the pedal, tighten the screw.
Attaching the Kick Trigger
Pedal /Bass drum pedal
Drum Pad
Bass drum pedal
[1] Place the pedal on the floor on your left side.
[2] Place the bass drum pedal on the floor in the center of rack.
[3] Please connect the clearly marked cables from the pads to
the correct inputs on the drum module, and you are ready to
play!
To Kick
Tom 3To
Tom 1To
Cymbal Pad
To Crash
Hi-HatTo
Drum Module
RideTo
Tom 2To
SnareTo
To Hi-Hatcontrol
Hi-Hat Pedal
[2][1]
Attaching the Drum Throne ___(Optional)
[1] Attach the standard-gauge tubing to the round seat.
[2] Tighten the wing nut on the round seat.
[3] Open the legs.
[4] Remove the wing nut and screw attached to the
Double-Braced Legs.
[5] Attach the standard-gauge tubing to the
Double-Braced Legs.
[6] Reattach the wing nut and screw.
[7] Tighten the wing nut and screw.
,
Attaching the Drum Throne
Round Seat
[Stool box] (Optional)
Standard-gauge tubing
Double-Braced Legs
[1]
[2]
[3] [3]
[3]
[4]
[5]
[6] [7]
Headphones
[HEADPHONES] (Optional)
[4]