Apeda Paking Study

ANNEXURE – I B

SPECIFICATIONS OF CONSUMER PACKS

A Flexible Pouches : ( 500 grams, 1 kg and 2 kg ) Material of Pouch : Laminate of polyester/LDPE Thickness : Polyester – 12 micron LDPE - 50 micron The material shall be either extrusion laminated, or in the case of adhesive lamination, food grade, odour freeadhesive should be used. Type of Pouch : a) Pillow Pouch or b) Side gusseted pouch Dimensions of pouch : As indicated in Annexure I – A. Bond Strength : 250 gm /15 mm (minimum) Heat Seal Strength : 2kg / 15 mm ( minimum) Seal width : 5 mm ( minimum ) Note : 1 . While the above is indicative type of laminate that is recommended, any other flexible film or laminatecomparable to the the barrier, strength and printing properties and low temperature stability of the abovelaminate would also be accepted. 2 . Tolerance a) Permissiable lower level Polyester film ( -5% ) (minus 5 percent ) Polyethylene film ( -10 % ) ( minus 10 percent )

b) Upper Level

A higher specification ( positive tolerance ) always could be acceptable, but however should not lead to high rigidity, flex crack,,reduced bond strength or seal strength. A higher specification may add to the cost. 3. The laminate material could be transparent/opaque/coloured as per the requirements of the importer. 4.. All the materials used shall be of food grade and pass the prescribed Indian standard/standards if any and as demanded by the importing countries. 5. Printing requirements shall conform to as prescribed by the importing countries.

6. General observations :

a) The pouches shall be clean and without any specs.b) The pouches shall be 3 sides or 4 sides sealed, or gusseted.c) The seal width shall be minimum 5 mm, particularly the top seal (for filled pouches ).d) The pouches shall be either reverse or surface printed. In the case of surface print, the print shall be

compatible with the product and shall not lift or smudge. The print shall be legible and easy to read. B. Plastic Punnet ( 500 grams ) Material : Food grade, odourless PET ( polyethylene terephthalate) Design : As per drawings no.3 Dimensions : As indicated in Annexure – I A. Approx. Wt.(gms) : 25.00 Note : The lid should sit firmly on the tray and should be lockable type.

ANNEXURE – II C1

SPECIFICATION DETAILS OF TRANSPORT PACK Product : Precut frozen fruits and vegetables . Type of Consumer Pack : a) Flexible Pillow Pouch. b) Flexible gusseted pouch Capacity of Consumer Pack : 500 grams., 1 kg., 2 kg. Material of Construction : 3 - ply corrugated fibre board* External Dimensions (mm) : a) 400 x 300 x 315 b) 500 x 400 x 200 Style of Box : a) RSC (0201) b) Telescopic (0312) Type of Flutes : ‘B’/narrow Direction of Flutes : Vertical Grammage (g/m2 ) : 190 / 150 /190. (outer to innner ) ( indicative ) Burst Factor of Kraft Paper : Min 25 Bursting Strength of Board ( kg/cm2 ) : Min 15 No. of pieces per Box : Not more than two Manufacturer’s Joint : By gluing Compression Strength of box (kgf) : Min 300 Cobb (30 minutes) (g/m2) : Max. 60 * Outer ply with waterproof coating or plastic film lamination.Note : Dimensions of the box are modular to Euro pallets. However, any

other dimensions or box styles to suit importers requirements could also be used.

ANNEXURE – II – C2SPECIFICATION DETAILS OF TRANSPORT PACK.

Product : Precut frozen fruits and vegetables . Type of Consumer Pack : Plastic Punnet with Lid Capacity of Consumer Pack : 500 grams. Material of Construction : 3 - ply corrugated fibre board * External Dimensions (mm) : 500 x 300 x 200 Style of Box : a) RSC 0201 b) Telescopic 0312 Type of Flutes : ‘B’/narrow Direction of Flutes : Vertical Grammage (g/m2) : 190 / 150 /190. (outer to innner ) (indicative ) Burst Factor of Kraft Paper : Min 25 Bursting Strength of Board (kg/cm2) : Min 15.0 No. of Pieces per box : Not more than two Manufacturers Joint : By gluing. Compression Strength (kgf) : Min 300 Cobb (30 minutes) (g/m2) : Max. 60 * Outer ply with water proof coating or plastic film lamination.Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirements could also be used.

ANNEXURE – II D SPECIFICATION DETAILS FOR PRESSURE SENSITIVE TAPE AND REINFORCEMENT STRAP

a) Pressure sensitive Tape

Material : BOPP or PVC ( biaxially oriented Polypropylene ) or

( Polyvinyl Chloride ) Width : 50 mm ( minimum ) Adhesion Property : To pass as per IS : 3676 – 1986 ( For further specification details refer IS : 2880 – 1987 ) b) Reinforcement Strap Material : PP or HDPE (Polypropylene or high density polyethylene) Width : 12mm (minimum ) Thickness : 0.50 mm ( minimum ) Breaking Load : 80 kg / 12 mm width Elongation : 25 % ( maximum )

ANNEXURE – III ASPECIFICATION DETAILS FOR DIRECT BULK PACK

PRODUCT : Okra / Beans / Bitter gourd / Acid lime CAPACITY : 10 kg.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 200 3) STYLE OF BOX : RSC (0201) ** 4) TYPE OF FLUTES : B/B 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 5 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : 250/120/120/120/120 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 14.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) : 400.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 16.00 15) DIAMETER AND POSITION : 20 mm. 3 holes each on the two sides. OF HOLES 1 hole each on the two ends.

4 holes each on top & bottom. * Outer ply of White duplex board ** Or any other suitable style which provides equal strength and performance

ANNEXURE – III BSPECIFICATION DETAILS FOR DIRECT BULK PACK

PRODUCT : Okra / Beans / Bitter gourd / Acid lime CAPACITY : 10 kg. 1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 200 3) STYLE OF BOX : Telescopic (0300) ** 4) TYPE OF FLUTES : Lid / Tray : B(narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid / Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid / Tray : 11.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 400.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 16.00 15) DIAMETER AND POSITION : 3 holes each on the two sides. OF HOLES 1 hole each on the two ends. 4 holes each on top & bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE – III CSPECIFICATION DETAILS FOR DIRECT BULK PACK


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 200 3) STYLE OF BOX : Telescopic (0306) ** 4) TYPE OF FLUTES : Lid / Tray : B(narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3

7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid / Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid / Tray : 11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 400.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 16.00 15) DIAMETER AND POSITION : 20 mm. 3 holes each on the two sides. OF HOLES 1 hole each on the two ends. 4 holes each on the top &bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE - III DSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 200 3) STYLE OF BOX : Telescopic (0312) ** 4) TYPE OF FLUTES : Lid : B(narrow), Tray : B/B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : Lid / Tray : 3/5 7) GRAMMAGE (G/ M.SQ.) : Lid : 250/150/150 (OUTER TO INNER) Tray : 250/120/120/120/120 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid / Tray : 11/ 14 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 400.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 16.00

15) DIAMETER AND POSITION : 20 mm. 3 holes each on the two sides. OF HOLES 1 hole each on the two ends. 4 holes each on the top & bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE – III ESPECIFICATION DETAILS FOR DIRECT BULK PACKS

PRODUCT : Okra / Beans / Bitter gourd / Papaya / Pineapple CAPACITY : 5 - 7 kg.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 200 3) STYLE OF BOX : RSC (0201) ** 4) TYPE OF FLUTES : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 350.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20 mm. 2 holes each on the two sides. OF HOLES 1 hole each on the two ends. 4 holes each on the top &bottom. * Outer ply of White duplex board. ** Or any other suitable style which provides equal strength and performance.

ANNEXURE – III FSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 200 3) STYLE OF BOX : Telescopic (0300) **

4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid / Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11/ 11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 350.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20 mm. 2 holes each on two sides. OF HOLES 1 hole each on two ends. 4 holes each on top & bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE – III GSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 200 3) STYLE OF BOX : Telescopic (0306) ** 4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid / Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11/ 11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 350.00

13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20 mm. 2 holes each on the two sides. OF HOLES 1 hole each on the two ends. 4 holes each on top & bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE – III HSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 200 3) STYLE OF BOX : Telescopic (0312) ** 4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid / Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 350.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20 mm. 2 holes each on both the sides. OF HOLES 1 hole each on both the ends. 4 holes each on top &bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE - III ISPECIFICATION DETAILS FOR DIRECT BULK PACKS

PRODUCT : Bitter gourd / Cucumber/ Acid lime/ Chikoo CAPACITY : 4 - 6 kg.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 150 3) STYLE OF BOX : RSC (0201) ** 4) TYPE OF FLUTES : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 350.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 10.00 15) DIAMETER AND POSITION : 20.00 mm. 2 holes each on the two sides. OF HOLES 1 hole each on the two ends. 2 holes each on top & bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance.

ANNEXURE – III JSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 150 3) STYLE OF BOX : Telescopic (0300) ** 4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid/Tray : 250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid /Tray: 11.00 / 11.00 9) NO. OF PIECES PER BOX : Not more than two 10) MANUFACTURER’S JOINT : By gluing

11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 350.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 10.00 14) DIAMETER AND POSITION : 20.00 mm. 2 holes each on the two sides. OF HOLES 1 hole each on the two ends. 2 holes each on top &bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE – III KSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 150 3) STYLE OF BOX : Telescopic (0306) ** 4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid/Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid /Tray: 11.00 / 11.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 350.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 10.00 15) DIAMETER AND POSITION : 20.00 2 holes each on the two sides. OF HOLES 1 hole each on the two ends. 2 holes each on top & bottom.ends. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE - III L

SPECIFICATION DETAILS FOR DIRECT BULK PACKS PRODUCT : Bitter gourd / Cucumber/ Acid lime/ Chikoo CAPACITY : 4 - 6 kg.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 150 3) STYLE OF BOX : Telescopic (0312) ** 4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid/Tray : 250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid /Tray: 11.00 / 11.00 9) NO. OF PIECES PER BOX : Not more than two 10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 350.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 10.00 14) DIAMETER AND POSITION : 20.00 mm. OF HOLES 2 holes each on the two sides. 1 hole each on the two ends. 2 holes each on top & bottom.* Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE – III MSPECIFICATION DETAILS FOR DIRECT BULK PACKS

PRODUCT : Okra / Beans / Bittergourd / Papaya CAPACITY : 8 kg.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 150 3) STYLE OF BOX : RSC (0201) ** 4) TYPE OF FLUTES : B/B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 5 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : 250/120/120/120/120 8) BURST FACTOR OF PAPER (KRAFT) : 20.00

9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 16.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two sides. OF HOLES 1 hole each on the two ends. 4 holes each on the top & bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE - III NSPECIFICATION DETAILS OF DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 150 3) STYLE OF BOX : Telescopic (0300) ** 4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid/Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 16.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two sides. OF HOLES 1 hole each on the two ends. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE – III OSPECIFICATION DETAILS OF DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 150 3) STYLE OF BOX : Telescopic (0306) ** 4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid/Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11/11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 16.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two sides. OF HOLES 1 hole each on the two ends. 4 holes each on the top & bottom* Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE – III PSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 150 3) STYLE OF BOX : Telescopic (0312) ** 4) TYPE OF FLUTES : Lid/Tray : B/B (narrow) 5) DIRECTION OF FLUTES : 6) NO. OF PLIES : Lid/Tray: 3/5 7) GRAMMAGE (G/ M.SQ.) : Lid : 250/150/150

(OUTER TO INNER) Tray : 250/120/120/120/120 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11/14 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 16.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two sides. OF HOLES 1 hole each on the two ends. 4 holes each on top & bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE - III QSPECIFICATION DETAILS OF DIRECT BULK PACKS

PRODUCT : Pomegranate CAPACITY : 5 kg. (approx. 12 nos.)

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 105 3) STYLE OF BOX : RSC (0201) ** 4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid/Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 250.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20.00 mm. 3 holes on the two sides. OF HOLES 1 hole on the two ends. 3 holes on top & bottom. * Outer ply of White duplex board.

** Or any other suitable style which provides equal strength and performance

ANNEXURE – III RSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 105 3) STYLE OF BOX : Telescopic (0300) ** 4) TYPE OF FLUTES : Lid/Tray : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid/Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 250.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two sides. OF HOLES 1 hole each on the two ends. 3 holes each on the top &bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

:

ANNEXURE - III SSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 105 3) STYLE OF BOX : Telescopic (0306) ** 4) TYPE OF FLUTES : Lid/Tray : B 5) DIRECTION OF FLUTES : Vertical

6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid/Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two sides. OF HOLES 1 hole each on the two ends. 3 holes each on top &bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE - III TSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 105 3) STYLE OF BOX : Telescopic (0312) ** 4) TYPE OF FLUTES : Lid/Tray : B (narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : Lid/Tray : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : Lid/Tray : 11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 250.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00

15) DIAMETER AND POSITION : 20.00 mm 3 holes on the two sides. 1 hole on the two ends. 3 holes each on top & bottom.* Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE - III USPECIFICATION DETAILS FOR DIRECT BULK PACKS

PRODUCT : Snakegourd CAPACITY : 5 kg.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 200 x 120 3) STYLE OF BOX : RSC (0201) ** 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 250.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two ends. OF HOLES 4 holes each on top & bottom. * Outer ply of White duplex board** Or any other suitable style which provides equal strength and performance

ANNEXURE - III VSPECIFICATION DETAILS FOR DIRECT BULK PACKS

PRODUCT : Drumstick CAPACITY : 7 kg.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 600 x 250 x 135 3) STYLE OF BOX : RSC (0201) ** 4) TYPE OF FLUTES : B (Narrow)

5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two ends. OF HOLES 4 holes each on the top &bottom. * Outer ply of White duplex board ** Or any other suitable style which provides equal strength and performance

ANNEXURE - III WSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 600 x 250 x 110 3) STYLE OF BOX : RSC (0201) ** 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 3 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : 250/150/150 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 250.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00

14) NO. OF VENTILATION HOLES : 14.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two ends. OF HOLES 4 holes each on top & bottom. * Outer ply of White duplex board ** Or any other suitable style which provides equal strength and performance

ANNEXURE - III XSPECIFICATION DETAILS FOR DIRECT BULK PACKS


1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 600 x 250 x 200 3) STYLE OF BOX : RSC (0201) ** 4) TYPE OF FLUTES : B/B (narrow/narrow) 5) DIRECTION OF FLUTES : Vertical 6) NO. OF PLIES : 5 7) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : 250/120/120/120/120 8) BURST FACTOR OF PAPER (KRAFT) : 20.00 9) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 14.00 10) NO. OF PIECES PER BOX : Not more than two 11) MANUFACTURER’S JOINT : By gluing 12) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 400.00 13) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 14) NO. OF VENTILATION HOLES : 16.00 15) DIAMETER AND POSITION : 20.00 mm 3 holes each on the two ends. OF HOLES 2 holes each on the two ends. 4 holes each on top & bottom. * Outer ply of White duplex board ** Or any other suitable style which provides equal strength and performance ANNEXURE - IV

SPECIFICATION DETAILS FOR PRESSURE SENSITIVE TAPE AND REINFORCEMENT STRAP PRESSURE SENSITIVE TAPE : Material : BOPP or PVC (Biaxally Oriented Polypropylene ) OR

(Polyvinyl Chloride) Width : 50 mm (minimum) Adhesion Property : To pass as per IS 3676-1986. (For further specification details refer IS 2880-1987) REINFORCEMENT STRAP : Material : PP (Polypropylene) Width : Min. 12 mm Thickness : Min. 0.50 mm Breaking Load : 80 kg / 12 mm width Elongation : Max 25%

ANNEXURE V-ASPECIFICATION DETAILS FOR DIRECT BULK PACK

PRODUCT : Apples – Direct bulk (with slotted partitions) CAPACITY : Appx. 16 Kg. (80 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply. EXTERNAL DIMENSIONS (MM) : 400 x 330 x 370 STYLE OF BOX : ** Telescopic - 0320 TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 25 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 12.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 500 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box,

DIAMETER AND POSITION OF as shown in drawing no. 13 HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE V-BSPECIFICATION DETAILS FOR DIRECT BULK PACK

PRODUCT : Apples – Direct bulk (with moulded pulp trays) CAPACITY : Appx. 16 kg. (80 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply EXTERNAL DIMENSIONS (MM) : 520 x 315 x 300 STYLE OF BOX : ** Telescopic - 0320 TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 25 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 12.0 NUMBER OF PIECES PER BOX : Not more than two. MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 500 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends box, DIAMETER AND POSITION OF as shown in drawing no. 12.HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE - VI

SPECIFICATION DETAILS FOR PARTITIONS & SEPARATOR PLATESDIRECT BULK PACK FOR APPLES

MATERIAL OF CONSTRUCTION : Corrugated Fibre board - 3 ply. TYPE OF FLUTES : B (narrow)

DIRECTION OF FLUTES FOR PARTITIONS : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER : 150/150/150 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 6.50

ANNEXURE - XII

SPECIFICATION OF CONSUMER PACKS

A) Flexible Pouches : (250 grams, 500 grams) Material of pouch : LDPE or PP Thickness (microns) : 37.5 or 25 Type of pouch : Pillow pouch Seal width : 5 mm (minimum) Note : 1) Tolerance

a) Permissiable Lower Level Polyethylene film (- 1.0%) Polypropylene film (- 10%) b) Upper Level

A higher specification (positive tolerance) always could be acceptable, but however should not lead tohigh rigidity, flex crack or reduced seal strength. A higher specification may add to the cost.

2) The material could be transparent/opaque coloured as per the requirements of

the importer.

3) The materials used shall be food grade and pass the prescribed Indian Standard / Standards if any, and as demanded by the importing countries.

4) Printing requirements shall conform to as prescribed by the importing countries. 5) General Observations : a) The pouches shall be clean and without any foreign particle b) The pouches shall be 3 sides or 4 sides sealed or gusseted. c) The seal width shall be minimum 5mm, particularly the top seal (for filled pouches) d) The pouches shall be either reverse or surface printed. In the case of surface print, the print shall be compatible with the product and shall not lift or smudge. The print shall be legible and easy to read. B) Plastic Punnet : (250 grams, 500 grams) Material : Food grade, odourless PET (Polyethylene Terepthalate) Design : As per prototypes Note : The lid should sit firmly on the tray and should be lockable type. C) Woven Net bag – String pull type Material : HDPE (High Density Polyethylene) OR PA (Polyamide) Weight Per Mt. Sq. : 45 min. D) Stretch film Material : Food grade, odourless, stretchable. LDPE : (Low Density Polyethylene) film

OR LLDPE : (Linear Low Density Polyethylene) film OR PVC : (Polyvinyl Chloride) film Thickness : 15.00 (micron) F) EPS Tray Material of : (EPS) Expanded Polystyrene Construction Density g/cc : 0.08 Thickness : Not more than 5mm.

ANNEXURE XV-A

SPECIFICATION DETAILS OF TRANSPORT PACK FOR CONSUMER PACK PRODUCT : Okra / Beans / Snow peas / Snap peas TYPE OF CONSUMER PACK : a) Flexible Pouch b) Woven net bag CAPACITY OF CONSUMER PACK : 250 grams, 500 grams.

1) MATERIAL OF CONSTRUCTION : 3 – ply Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 400 x 140 3) STYLE OF BOX : a) RSC (0201) b) Telescopic (0312) 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : * 250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 9) NO. OF PIECES PER BOX : Not more than two

10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 16.00 14) DIAMETER AND POSITION : 20 mm - Drawing nos. 10 & 11. OF HOLES 3 holes each on the two sides, 1 hole each on the two ends. 4 holes each on top & bottom. * Outer ply of White duplex board Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirement could also be used.

ANNEXURE XV-B

SPECIFICATION DETAILS OF TRANSPORT PACK FOR CONSUMER PACK PRODUCT : Okra / Beans/Snow peas / Snap peas TYPE OF CONSUMER PACK : a) Plastic punnet with lid b) Plastic punnet stretch wrapped CAPACITY OF CONSUMER PACK : 250 grams.

1) MATERIAL OF CONSTRUCTION : 3 – ply Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 400 x 95 3) STYLE OF BOX : One piece tuck-in-type 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : * 250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 9) NO. OF PIECES PER BOX : One 10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 19.00 14) DIAMETER AND POSITION : As shown in drawing nos. 12 & 13 OF HOLES * Outer ply of White duplex board Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirement could also be used.

ANNEXURE XV-C

SPECIFICATION DETAILS OF TRANSPORT PACK FOR CONSUMER PACK PRODUCT : Okra / Beans / Snow peas / Snap peas TYPE OF CONSUMER PACK : a) Plastic punnet with lid b) Plastic punnet stretch wrapped CAPACITY OF CONSUMER PACK : 500 grams.

1) MATERIAL OF CONSTRUCTION : 3 – ply Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 400 x 135 3) STYLE OF BOX : One piece tuck-in-type 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : * 250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 9) NO. OF PIECES PER BOX : One 10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 19.00 14) DIAMETER AND POSITION : As shown in drawing nos. 12 & 13 OF HOLES * Outer ply of White duplex board Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirement could also be used.

ANNEXURE XV-DSPECIFICATION DETAILS OF TRANSPORT PACK FOR CONSUMER PACK PRODUCT : Okra / Beans / Snow peas / Snap peas TYPE OF CONSUMER PACK : a) Plastic punnet with lid b) Plastic punnet stretch wrapped CAPACITY OF CONSUMER PACK : 250 grams.

1) MATERIAL OF CONSTRUCTION : 3 – ply Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 100 3) STYLE OF BOX : a) Telescopic (0306) b) Telescopic (0312) 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : * 250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00

8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 9) NO. OF PIECES PER BOX : Not more than two 10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 16.00 14) DIAMETER AND POSITION : 20 mm - drawing nos. 14 & 15 OF HOLES 3 holes each on the two sides 1 holes each on the two sides. 4 holes each on top and bottom. * Outer ply of White duplex board Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirement could also be used.

ANNEXURE XV-ESPECIFICATION DETAILS OF TRANSPORT PACK FOR CONSUMER PACK PRODUCT : Asparagus TYPE OF CONSUMER PACK : EPS tray stretch wrapped CAPACITY OF CONSUMER PACK : 400 grams.

1) MATERIAL OF CONSTRUCTION : 3 ply Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 500 x 300 x 100 3) STYLE OF BOX : a) Telescopic (0306) b) Telescopic (0312) 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : *250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 9) NO. OF PIECES PER BOX : Not more than two 10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 16.00 14) DIAMETER AND POSITION : 20 mm Drawing nos. 14 & 15 OF HOLES 3 holes each on the two sides 1 hole each on the two ends 4 holes each on top and bottom * Outer ply of White duplex board Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirement could also be used.

ANNEXURE XV-FSPECIFICATION DETAILS OF TRANSPORT PACK FOR CONSUMER PACK PRODUCT : Asparagus TYPE OF CONSUMER PACK : Flexible pillow pouch CAPACITY OF CONSUMER PACK : 200 grams.

1) MATERIAL OF CONSTRUCTION : 3 ply Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 60 3) STYLE OF BOX : a) Telescopic (0300) 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : *250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 9) NO. OF PIECES PER BOX : Not more than two 10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 16.00 14) DIAMETER AND POSITION : 20 mm Drawing no. 16. OF HOLES 3 holes each on the two sides 1 hole each on the two ends 4 holes each on top and bottom * Outer ply of White duplex board Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirement could also be used.

ANNEXURE XV-GSPECIFICATION DETAILS OF TRANSPORT PACK FOR CONSUMER PACK PRODUCT : Asparagus TYPE OF CONSUMER PACK : Stretch wrapped in bunches CAPACITY OF CONSUMER PACK : 200 grams.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 380 x 240 x 80 3) STYLE OF BOX : Telescopic (0300)

4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : *250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 9) NO. OF PIECES PER BOX : Not more than two 10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 16.00 14) DIAMETER AND POSITION : 20 mm. Drawing no. 16. OF HOLES 3 holes each on the two sides 1 hole each on the two ends 4 holes each on top andbottom * Outer ply of White duplex board Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirement could also be used.

ANNEXURE XV-HSPECIFICATION DETAILS OF TRANSPORT PACK FOR CONSUMER PACK PRODUCT : Lychees / Strawberries TYPE OF CONSUMER PACK : Plastic punnet stretch wrapped, punnet stretch wrapped & EPS tray stretch wrapped. CAPACITY OF CONSUMER PACK : 250 grams.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 300 x 65 3) STYLE OF BOX : One piece tuck-in-type 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : * 250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 9) NO. OF PIECES PER BOX : One 10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 12) COBB (30 MINUTES)

(G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 19.00 14) DIAMETER AND POSITION : As shown in drawing no. 17 OF HOLES * Outer ply of White duplex board Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirement could also be used.

ANNEXURE XV-ISPECIFICATION DETAILS OF TRANSPORT PACK FOR CONSUMER PACK PRODUCT : Strawberries TYPE OF CONSUMER PACK : Bamboo basket CAPACITY OF CONSUMER PACK : 250 grams.

1) MATERIAL OF CONSTRUCTION : Corrugated fibre board * 2) EXTERNAL DIMENSIONS (MM) : 400 x 400 x 80 3) STYLE OF BOX : One piece tuck-in-type 4) TYPE OF FLUTES : B (Narrow) 5) DIRECTION OF FLUTES : Vertical 6) GRAMMAGE (G/ M.SQ.) (OUTER TO INNER) : * 250/150/150 7) BURST FACTOR OF PAPER (KRAFT) : 20.00 8) BURSTING STRENGTH OF BOARD (KG/CM.SQ.) : 11.00 9) NO. OF PIECES PER BOX : One 10) MANUFACTURER’S JOINT : By gluing 11) COMPRESSION STRENGTH OF BOX (KGF) (MIN) : 300.00 12) COBB (30 MINUTES) (G/M.SQ.) (MAX.) : 60.00 13) NO. OF VENTILATION HOLES : 19.00 14) DIAMETER AND POSITION : As shown in drawing no. 18 OF HOLES * Outer ply of White duplex board Note : Dimensions of the box are modular to Euro pallets. However, any other dimensions or box styles to suit importers requirement could also be used.

ANNEXURE – III

SPECIFICATION DETAILS OF CONSUMER PACKS FORAPPLES, STRAWBERRIES, AND CHERRIES.

A. APPLES a) Tubular extruded plastic net

Material : HDPE (High Density Polyethylene) Stretch width : 200 – 400 mm

b) Woven plastic bag Material : HDPE (High Density Polyethylene) Or PA (Polyamide) Weight per Mtr. Sq. : 45 (min.) c) EPS Tray Material of construction : Expanded polystyrene (EPS) Density (g/cc) : 0.08 Thickness : Not more than 5 mm. d) Stretch Film Material : Food grade, odourless, stretchable LDPE ( Low Density Polyethylene) film Or LLDPE (Linear Low Density Polyethylene) film Or PVC (Polyvinyl Chloride) film. Thickness : 15.00 (microns) e) Moulded Pulp Tray Material : Recyclable waste paper Design : As per sample – 6 cavities f) CFB Tray MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply. EXTERNAL DIMENSIONS (MM) : a) 433 x 333 x 95 b) 500 x 400 x 95 STYLE OF BOX : ** One piece, tuck-in-tray type. TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 11.0 NUMBER OF PIECES PER BOX : One MANUFACTURER’S JOINT : Nil COMPRESSION STRENGTH

OF BOX (KGF) (MIN.) : 250 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES : As shown in drawing no. 6-A * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance B. STRAWBERRIES / CHERRIES a) Plastic Punnet Material of construction : Food grade, odourless PET (Polyethylene Terephthalate) Design : As per prototypes. b) Stretch Film Material : Food grade, odourless, stretchable LDPE ( Low Density Polyethylene) film Or LLDPE (Linear Low Density Polyethylene) film Or PVC (Polyvinyl Chloride) film. Thickness : 15.00 (minimum) (microns) c) EPS Tray Material of Construction : Expanded Polystyrene (EPS) Density (g/cc) : 0.08 Thickness : Not more than 5 mm.

ANNEXURE IV-ASPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples – Transport pack for Consumer packs Consumer Pack - Extruded Plastic tubular net CAPACITY : Appx. 8 Kg. (40 nos.)

MATERIAL OF CONSTRUCTION : * Corrugated fibre board – 5 ply. EXTERNAL DIMENSIONS (MM) : 425 x 320 x 195 STYLE OF BOX : ** RSC – 0201 TYPE OF FLUTES : B/B (narrow/narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/120/120/120/120. BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20 BURSTING STRENGTH OF BOARD (KG/CM.SQ) (MIN.) : 14.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box,DIAMETER AND POSITION OF as shown in drawing no. 1HOLES* Outer ply of White duplex board** Or any other suitable style which provide equal strength and performance

ANNEXURE IV- BSPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples – Transport pack for Consumer packs Consumer Pack - Extruded Plastic tubular net CAPACITY : Appx. 8 Kg. (40 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply. EXTERNAL DIMENSIONS (MM) : 430 x 325 x 195 STYLE OF BOX : ** Telescopic - 0300 TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OF BOARD (KG/CM.SQ) (MIN.) : 11.0 NUMBER OF PIECES PER BOX : Two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400

COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box, DIAMETER AND POSITION OF as shown in drawing no. 2HOLES * Outer ply of White duplex board.* * Or any other suitable style which provide equal strength and performance

ANNEXURE IV-CSPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples – Transport Pack for Consumer Packs Consumer Pack - Extruded tubular Plastic Net CAPACITY : Appx. 8 Kg. (40 nos.) MATERIAL OF CONSTRUCTION : *Corrugated Fibre board. Tray - 5 ply, Lid - 3 ply. EXTERNAL DIMENSIONS (MM) : 430 x 325 x 195 STYLE OF BOX : ** Telescopic - 0306 TYPE OF FLUTES : 3 ply-B (narrow), 5 ply -B/B(narrow/narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) : 3 ply - 250/150/150 OUTER TO INNER (INDICATIVE) : 5 ply - 250/120/120/120/120 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OF : 3 ply - 11.0BOARD (KG/CM.SQ) (MIN.) : 5 ply - 14.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES , : One slot on each of the ends of the box, DIAMETER AND POSITION OF as shown in drawing no. 3HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE IV-DSPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples – Transport pack for Consumer packs Consumer Pack -Woven net bag, String pull type CAPACITY : Appx. 10 Kg. (48 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board box – 5 ply

EXTERNAL DIMENSIONS (MM) : 495 x 295 x 195 STYLE OF BOX : ** RSC - 0201 TYPE OF FLUTES : B/B (narrow/narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/120/120/120/120 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 14.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box, DIAMETER AND POSITION OF as shown in drawing no. 4HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE IV-ESPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples - Transport Pack for Consumer packs Consumer pack -Woven net bags string pull type CAPACITY : Appx. 10 Kg.(48 nos.) MATERIAL OF CONSTRUCTION : *Corrugated Fibre board box–3 ply EXTERNAL DIMENSIONS (MM) : 500 x 300 x 195 STYLE OF BOX : ** Telescopic - 0300 TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 11.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400 COBB (30 MINUTES)

(G/M.SQ.) (MAX.) : 120 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box,DIAMETER AND POSITION OF as shown in drawing no. 5HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE IV-FSPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples - Transport Pack for Consumer packs Consumer pack - Woven net bag, string pull type CAPACITY : 10 Kg. (48 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board box. Tray – 5 ply, Lid – 3 ply, EXTERNAL DIMENSIONS (MM) : 500 x 300 x 195 STYLE OF BOX : ** Telescopic - 0306. TYPE OF FLUTES : 3 ply-B (narrow), 5 ply-B/B (narrow/narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) : 3 ply - 250/150/150 OUTER TO INNER (INDICATIVE) 5 ply - 250/120/120/120/120 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OF : 3 ply - 11.0BOARD (KG/CM.SQ) (MIN.) : 5 ply - 14.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box, DIAMETER AND POSITION OF as shown in drawing no. 6.HOLES* Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE IV-GSPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples - Transport Pack for Consumer packs Consumer Pack - EPS Tray, stretch wrapped CAPACITY : Appx. 7 Kg. (36 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply. EXTERNAL DIMENSIONS (MM) : 500 x 400 x 195

STYLE OF BOX : ** Telescopic - 0300 TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 11.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of DIAMETER AND POSITION OF the box, as shown in drawing no. 7HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE IV-HSPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples - Transport Pack for Consumer packs Consumer pack - EPS Tray, stretch wrapped CAPACITY : Appx. 7 Kg. (36 nos.) MATERIAL OF CONSTRUCTION : * Corrugated fibre board. Tray – 5 ply, Lid – 3 ply. EXTERNAL DIMENSIONS (MM) : 500 x 400 x 195 STYLE OF BOX : ** Telescopic – 0306. TYPE OF FLUTES : 3 ply - B(narrow), 5 ply -B/B(narrow/narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) : 3 ply - 250/150/150 OUTER TO INNER (INDICATIVE) : 5 ply - 250/120/120/120/120 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OF : 3 ply - 11.0BOARD (KG/CM.SQ) (MIN.) 5 ply - 14.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400 COBB (30 MINUTES)

(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box, DIAMETER AND POSITION OF as shown in drawing no. 8.HOLES* Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE IV-ISPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples - Transport Pack for Consumer packs Consumer pack - Moulded pulp trays CAPACITY : Appx. 14 Kg. (72 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply. EXTERNAL DIMENSIONS (MM) : 470 x 400 x 195 STYLE OF BOX : ** Telescopic - 0300 TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 11.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box,DIAMETER AND POSITION OF as shown in drawing no. 9HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE IV-J SPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Apples - Transport Pack for Consumer packs Consumer pack - Moulded pulp trays CAPACITY : Appx. 14 Kg. (72 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board. Tray – 5 ply, Lid – 3 ply.EXTERNAL DIMENSIONS (MM) : 470 x 400 x 195 STYLE OF BOX : ** Telescopic – 0306. TYPE OF FLUTES : B(narrow) - 3 ply, B/B (narrow/narrow) -5 ply

DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) : 3 ply – 250/150/150 OUTER TO INNER (INDICATIVE) 5 ply – 250/120/120/120/120 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OF : 3 Ply - 11.0BOARD (KG/CM.SQ) (MAX.) 5 Ply - 14.0 NUMBER OF PIECES PER BOX : Not More than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 400 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box,DIAMETER AND POSITION OF as shown in drawing no. 10HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE V-ASPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Strawberries -Transport Pack for Consumer Packs Consumer pack - Woven basket stretch wrapped CAPACITY : 1 Kg. MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply EXTERNAL DIMENSIONS (MM) : 400 x 400 x 80 STYLE OF BOX : ** One piece, tuck-in-type, tray. TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 11.0 NUMBER OF PIECES PER BOX : One MANUFACTURER’S JOINT : Nil COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 250 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : 19 holes as shown in drawing no. 16 DIAMETER AND POSITION OF

HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE V-BSPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Strawberries – Transport Pack for Consumer Packs Consumer Packs - (a) Punnet (b) Tray with stretch wrap. CAPACITY : 2 Kg. MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply. EXTERNAL DIMENSIONS (MM) : 400 x 300 x 65 STYLE OF BOX : ** One piece, tuck-in-tray type. TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20.0 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 11.0 NUMBER OF PIECES PER BOX : One MANUFACTURER’S JOINT : Nil COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 250 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : 19 holes as shown in drawing no. 15DIAMETER AND POSITION OFHOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE VISPECIFICATION DETAILS OF TRANSPORT PACKS

PRODUCT : Cherries – Transport pack for Consumer packs Consumer pack - punnet, tray stretch wrapped, EPS tray stretch wrapped CAPACITY : 1.2 to 1.6 Kg. MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply. EXTERNAL DIMENSIONS (MM) : 400 x 300 x 65 STYLE OF BOX : ** One piece, tuck-in-type tray. TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical

GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 20 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 11.0 NUMBER OF PIECES PER BOX : One MANUFACTURER’S JOINT : Nil COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 250 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60

NO. OF VENTILATION HOLES, : 19 holes as shown in drawing no. 14DIAMETER AND POSITION OFHOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE - VII

SPECIFICATION DETAILS FOR PARTITIONS & PLATES MATERIAL OF CONSTRUCTION : Corrugated Fibre board - 3 ply. TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES FOR PARTITIONS : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER : 150/150/150 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 6.50

ANNEXURE - VIII

SPECIFICATION DETAILS FORPRESSURE SENSITIVE TAPE & REINFORCEMENT STRAP

A) PRESSURE SENSITIVE TAPE Material : BOPP or PVC (biaxially oriented Polypropylene or Polyvinyl chloride) Width : 50 mm Adhesion property to pass as per IS: 3676 - 1986 (For further specification details refer IS 2880 – 1978) B) REINFORCEMENT STRAP Material : PP (Polypropylene) Width : Min. 12 mm Thickness : Min. 0.50 mm Breaking load : 80 kg / 12 mm width Elongation : Max 25%

ANNEXURE IX-ASPECIFICATION DETAILS FOR DIRECT BULK PACK

PRODUCT : Apples – Direct bulk (with slotted partitions) CAPACITY : Appx. 16 Kg. (80 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply. EXTERNAL DIMENSIONS (MM) : 400 x 330 x 370 STYLE OF BOX : ** Telescopic - 0320 TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150

BURST FACTOR OF PAPER (KRAFT) (MIN.) : 25 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 12.0 NUMBER OF PIECES PER BOX : Not more than two MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 500 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends of the box, DIAMETER AND POSITION OF as shown in drawing no. 13 HOLES * Outer ply of White duplex board.** Or any other suitable style which provide equal strength and performance

ANNEXURE IX-BSPECIFICATION DETAILS FOR DIRECT BULK PACK

PRODUCT : Apples – Direct bulk (with moulded pulp trays) CAPACITY : Appx. 16 kg. (80 nos.) MATERIAL OF CONSTRUCTION : * Corrugated Fibre board – 3 ply EXTERNAL DIMENSIONS (MM) : 520 x 315 x 300 STYLE OF BOX : ** Telescopic - 0320. TYPE OF FLUTES : B (narrow) DIRECTION OF FLUTES : Vertical GRAMMAGE (G/M.SQ.) OUTER TO INNER (INDICATIVE) : 250/150/150 BURST FACTOR OF PAPER (KRAFT) (MIN.) : 25 BURSTING STRENGTH OFBOARD (KG/CM.SQ) (MIN.) : 12.0 NUMBER OF PIECES PER BOX : Not more than two. MANUFACTURER’S JOINT : By gluing COMPRESSION STRENGTHOF BOX (KGF) (MIN.) : 500 COBB (30 MINUTES)(G/M.SQ.) (MAX.) : 60 NO. OF VENTILATION HOLES, : One slot on each of the ends box, DIAMETER AND POSITION OF as shown in drawing no. 12.HOLES * Outer ply of White duplex board.** Or any other suitable style which provide qual strength and performance

ANNEXURE – XIII

RECOMMENDED SPECIFICATIONS FOR CONSUMER PACKSWALNUT KERNELS

A) Flexible Pouches for Packaging of Walnut Kernels

100 gm & 200 gm. Materials : Flexible laminates / Co-extruded films. a) Laminates : 1. 12 micron PET / 50 micron LDPE

2. 12 micron metallised PET / 50 micron LDPE 3. 10 micron PET / 9 micron Aluminium Foil /

50 micron LDPE. The materials shall be either extrusion laminated or in case of adhesive lamination, food grade odour freeadhesives should be used. (The adhesive should preferably be solventless).

b) Co-extruded Films : 1. 20 micron LD – 7.5 micron Tie – 25micron PA – 7.5 micron Tie – 30 micron LD.

The LD layer could also be LLD or LD – HD, LLD – HD or EAA. PET - Polyester LDPE – Low density polyethylene LD – Low density polyethylene PA – Polyamide (Nylon) LLD – Linear low density polyethylene HD – High density polyethylene EAA – Ethylene acrylic acid

contd .....

Dimensions : 200gms 100gms L x W (mm) (Indicative) Flat Pillow Pouch 250x140 190x120 Stand Up Pouch 215x140 170x115 65 mm bottom 50 mm bottom gusset width gusset width Performance : Bond strength : 250 gm /15 mm width (minimum). (in case of laminates only) Heat Seal Strength : 2 kg /15 mm width (minimum). Seal Width : 10 mm (minimum) Dart Impact : 350 (minimum) gf at 50% failure

Note :(1) While the above are indicative types of laminates and co-extruded films

that are recommended, any other flexible laminates or co-extruded films comparable to the barrier andstrength properties of above type of laminates or co-extruded films would also be acceptable.

(2) a) Thickness tolerance – (lower level permissible) Polyester films (-5%) (minus 5 percent) Polyethylene film (-10%) (minus 10 percent) Polypropylene film (-10%) (minus 10 percent) BOPP film (-5%) (minus 5 percent) Aluminium foil (-5%) (minus 5 percent) Co-extruded films (-10%) (minus 10 percent)

contd ......

b) Thickness tolerance – (Upper Level)

A higher specification (positive tolerance) always could be acceptable. However, it should not lead tohigh rigidity, flex crack, reduced bond strength or seal strength. A higher specification may also add tothe cost.

(3) The laminate / co-extruded film could be transparent/opaque/coloured

as per the requirement of the importer. (4) All the materials used shall be of food grade quality and pass the prescribed Indian Standards / Standards if any, and, as demanded by the importing countries. (5) Labelling and printing requirements shall conform to as prescribed by

the importing country. (6) General requirements : a) The pouches shall be clean and without specs. b) The pouches shall be 3 sides or 4 sides sealed. c) The seal width shall be minimum 5 mm, particularly the top seal (for filled pouches). d) The pouches shall be either reverse or surface printed. In the case of surface print, the print shall be compatible with the product and shall not lift or smudge . The print shall be legible and easy to read. e) The pouch shall not fail either on the body or along the seals when subjected to normal drop tests. f) All the pouches should be flushed with nitrogen gas at the time of sealing to retain the freshness of the product.

contd .....

B) Plastic Container for 100 gms. and 200 gms. Walnut Kernels

Material : Food Grade PET (Polyethylene Terephthalate) Brimful Capacity 100 gms : 340 ml 200 gms : 600 ml Dimensions 100 gms. 200 gms. (Indicative) Diameter : 65 mm. 65 mm. Height : 100 mm. 150 mm. Shape : As per export requirements. Wall thickness : 0.3 mm to 0.4 mm (minimum ) Tagger : Aluminium foil with heat seal lacquer Closure : Roll on cap Closure material : HIPS or HDPE (High impact polystyrene or High density polyethylene) The plastic containers should be nitrogen gas flushed to retain freshness of the product.

C) Composite Containers For 100 gms and 200 gms Walnut Kernels Material of Construction

a) Body : Paperboard, internally laminated with Aluminium foil / PE

Total wall thickness : 1.0 mm (minimum)Thickness of Al foil / PE : 0.050 mm (minimum)

(Thickness of PE: 0.025 mm to 0.0375 mm) b) Components : Tinplate or Plastic

i) Tinplate : Prime E-25 Thickness : 0.20 mm (nominal)

Lacquer : Internal - single epoxy (minimum 4.8g/m2 ) External - gold lacquered ii) Plastic : HDPE / HIPS (food grade) -

(High density polyethylene / High impact polystyrene)

Thickness : 0.10 mm minimum

Dimensions 100 gms. 200 gms.(Indicative) Height : 48 mm 98 mm Diameter : 86 mm 86 mm.

Contd ....

Construction : Shape - round Seaming - either double seaming or adhesive seaming. Seams should be leakproof.

Type of closure : Friction lid / lever lid . The container should be preferably provided with easy open ring pull type lid (full aperture open). Tagger of aluminium foil should be used The composite container should be leakproof and flushed with nitrogen gas to retain the freshness of the product

contd......

D) Metal Containers : For 100 gm & 200 gm of Walnut Kernels

Material of Construction : Tinplate prime Tin coating Inside : E 25 Outside : E 25

Thickness of tinplate : 0.30 mm (nominal)

Lacquer a) Internal : Min. 4.8 g/m2

(single coat epoxy lacquer) b) External : Printed design / decorative lacquer Dimensions 100 gms. 200 gms.(Indicative) Height : 48 mm 98 mm. Can be changed Diameter : 86 mm 86 mm. ) as per export requirement. Construction a) Shape : Round / Rectangular (depends on export requirement) b) Seaming : All dry seams, double seaming Vertical body seam should be welded. Components a) Material : Tinplate prime E-25 b) Thickness : Same as body c) Lacquer : Single epoxy lacquer – food grade (internal) : (minimum 4.8g/m2 ) (external) : Gold lacquered / printed Types of closures : Friction lid / lever lid. The container should be preferably provided with easy open ring pull type lid (Full

aperture open). An additional plastic cap over the lid should be provided.

contd ......

Tagger : Optional (for friction lid and lever lid closure) Labels : Printed, attractive, wrap around label, laminated or varnished. Alternatively, it is preferable to use printed tinplate.

The tinplate containers should be nitrogen gas flushed to retain freshness of the product.

ANNEXURE - XIVSPECIFICATIONS FOR TRANSPORT PACKS FOR

CONSUMER PACKS OF WALNUT KERNELS.

A) BOX Material of Construction : Corrugated fibreboard No. of Plies : Five External dimensions (mm) :

a) Flexible Pouches of100 grams. & 200 grams -Pillow & Stand-up pouches : 500 x 400 x 230

b) PET Containers 100grams & 200 grams : 500 x 300 x 330 c) Composite Containers 100 grams & 200 grams : 600 x 500 x 235 d) Tinplate Containers

100 grams & 200 grams : 600 x 500 x 235 Style of Box : RSC (regular slotted container) Type of Flutes : B/B (narrow/narrow) Direction of Flutes : Vertical Grammage (g/m2) Outer to Inner : 180/120/150/120/150 Bursting Strength (kg/cm2) : Min: 14.0

contd...

Burst factor : 20.0 (min.) No. of pieces per box : Maximum two Manufacturer’s joint : By gluing

Compression strength(Kgf) : Min : 400 Cobb (g/m2) 30 minutes : 120 (max.) B) SLOTTED PARTITIONS & PLATES Slotted partitions and plates are suggested to be used in transport packs containing PET, Composite andTinplate Containers. Slotted Partitions & Plates Material of Construction : Corrugated fibre board No. of Plies : Three Type of Flute : B (narrow) Grammage (g/m2) : 150/150/150

ANNEXURE –XV

SPECIFICATION DETAILS FOR MOULDED VACUUM PACK A) BARRIER BAG FOR 5KG WALNUT KERNELS Material of Construction: *

a) LaminatesØ LLDPE/ Polyester / LD-HD

Ø Polyester/ Met. Polyester/ LD-HD

Ø Polyester/ Al.Foil/ LD-HD

b) Co-Extruded films

Ø LLDPE – TIE – NYLON – TIE – LLDPE

Ø LLD/ TIE/ PA/ EVOH/ TIE

Total Thickness : 140 microns Seal width : 10 mm Water Vapour Transmission Rate : 1.0g/m2/24 Hrs (at 38 deg C, 90% RH)(Maximum)

Oxygen Transmission Rate : 30Cc/m2/24 Hrs at 1 atm (Maximum) *The types of materials recommended are laminates and 5-layered co-extruded structures. Any other laminates /5 layered co-extruded films having properties as given above can be used. The note, general requirements of Annexure - XIII also apply in this case.

contd...

B) OUTER BOX FOR 2 POUCHES (5Kg x 2 ) Material of construction : 5-ply corrugated fibreboard Style of Box : RSC (regular slotted container) Dimensions of box (External) mm : 455 x 255 x 245 Types of Flutes : B/B (narrow/narrow) Direction of flutes : Vertical. Grammage (g/m2) : 180/120/150/120/150 Bursting strength : 12.50(min) kg/cm2

Burst factor (min.) : 20.0 No. of pieces per box : Not more than two. Compression strength kgf : 300(min) Type of adhesive : Starch or any other suitable neutral adhesive. Cobb (30 minutes) g/m2 : 120(max) less if stored in cold storage contd .... C) OUTER BOX FOR 2 POUCHES (10 Kg x 2) Material of Construction : 5-ply corrugated fibreboard Style of Box : RSC (Regular Slotted Container) Dimensions of box

(External) mm : 490 x 255 x 365 Type of Flutes : B/B (narrow/narrow) Direction of Flutes : Vertical Grammage (g/m2) : 180/150/150/150/150 Bursting Strength(min.) (kg/cm2) : 18.0 Burst Factor (min.) : 20.0 No. of Pieces per box : Not more than two Compression Strength Kgf (min.) : 550 Type of adhesive : Starch or any other neutral adhesive Cobb (30 minutes) (g/m2)(max) : 120 – Less if stored in cold storage.

ANNEXURE – XVISPECIFICATION DETAILS FOR BAG-IN-BOX SYSTEM

A) BARRIER BAG FOR 5KG WALNUT KERNELS Material of Construction: *

a) Laminates

Ø LLDPE/ Polyester / LD-HD

Ø Polyester/ Met. Polyester/ LD-HD

Ø Polyester/ Al.Foil/ LD-HD b) Co-Extruded films

Ø LLDPE – TIE – NYLON – TIE – LLDPE

Ø LLD/TIE/ PA/ EVOH/ TIE

Total Thickness : 140 microns Seal width (minimum) : 10 mm Water Vapour Transmission Rate : 1.0g/m2/24 Hrs (at 38 deg C, 90% RH)(Maximum) Oxygen Transmission Rate : 30cc/m2/24 Hrs at 1 atm (Maximum)

* The types of materials recommended are laminates and 5-layered co-extruded structures. Any other laminates/ 5 layered co-extruded films having properties as given above can be used. The note , general requirements Annexure –XIII also apply in this case.

contd....

B) BOX FOR 5 KG WALNUT KERLELS Material of construction : 3 ply corrugated fibreboard. Style of Box : RSC (regular slotted container) - End opening Dimensions of box (External) mm : 440 x 245 x 120 Type of Flutes : B (narrow) Direction of flutes : Vertical. Grammage (g/m2) : 150/150/150 Bursting strength (min) kg/cm2 : 8.00 Burst factor (min.) : 20.0 No. of pieces per box : Not more than two. Compression strength kgf (min.) : 300 Type of adhesive : Starch or any other suitable neutral adhesive. Cobb (30 minutes) (g/m2) : 120(max) Less if stored under cold storage

contd ......

C) SLEEVE PASTED INSIDE THE 5KG BOX Material of construction : 3 ply corrugated fibreboard. Types of Flutes : B(narrow) Direction of flutes : Vertical Bursting strength (min) kg/cm2 : 7.00 Type of adhesive : Starch or any other suitable neutral adhesive.

D) OUTER TRANSPORT PACK ( 5kg x 2) Material of construction : 5-ply corrugated fibreboard Style of Box : RSC (regular slotted container) Dimensions of box (Ext) mm : 455 x 255 x 245 Types of Flutes : B/B (narrow/narrow) Direction of flutes : Vertical. Grammage (g/m2) : 180/120/150/120/150 Bursting strength : 12.50(min) (kg/cm2) Burst Factor (min.) : 20.0 contd. ....

No. of pieces per box : Not more than two. Compression strength kgf : 300(min) Type of adhesive : Starch or any other suitable neutral adhesive. Cobb ( 30 minutes) g/m2 : 120(max) less if stored in cold storage

Documents

Apeda Paking Study