Air Purifying Respirators page 8 Head, Eye & Face Protection page …fairpowerage.com/upload_file/catelogue_pdf/147_small_MSA... · 2019-01-28 · Portable Instruments page 29 Fixed

Note: This Bulletin contains only a generaldescription of the products shown. While usesand performance capabilities are described,under no circumstances shall the products beused by untrained or unqualified individualsand not until the product instructions includ-ing any warnings or cautions provided havebeen thoroughly read and understood. Onlythey contain the complete and detailed infor-mation concerning proper use and care ofthese products.

Offices and representatives worldwideFor further information:

Supplied Air Respirators page 3

Air Purifying Respirators page 8

Head, Eye & Face Protection page 13

Hearing Protection page 22

Fall Protection page 23

Portable Instruments page 29

Fixed Gas and Flame Detection page 35

Thermal Imaging page 27

MSA (India ) LimitedEcostationLevel-16 (Floor)Plot No.7, Block BPSalt Lakes, Sector VKolkata - 700 091 - IndiaPhone: +91-33-2367-2260 to 64Fax: +91-33-2367-2265E-mail: [email protected]

Fixed Gas and Flame Detection

Thermal Imaging

Portable Instruments

MSA IndiaSafety Solutions

Head, Eye & Face Protection

Hearing Protection

Fall Protection

Air Purifying Respirators

Supplied Air Respirators

MSA - The Safety CompanyA Worldwide Partner To Rely On

Registered & Head Office, KOLKATA Central Logistics Hub, NAVIMUMBAI

MSA India ServiceMSA India is now equipped to provide com-prehensive service plan to ensure that yourequipments and systems are reliable, econom-ical and always ready for use. With ServiceCentres in Mumbai and Kolkata our customerscan be given active, prompt and efficient sup-port by trained, qualified and MSA CertifiedService Engineers working on-site all overIndia.

For product repair questions or concerns, youmay contact [email protected]

About MSAEstablished in 1914, MSA is the world's leadingmanufacturer of sophisticated safety productsdesigned to protect people throughout theworld. The Company was founded by Two Vi-sionary Mining Engineers with a dream toPROTECT the Life of Miners.

With headquarters located in Cranberry, USA,MSA employs approximately 4,500 associatesand maintains operations that extend aroundthe world. These resources include manufac-turing operations on five continents and morethan 30 international locations that help pro-tect lives in more than 140 countries.

MSA in IndiaMSA India was established in 1965 with theaim of supplying safety equipments to Indianmines. From then till today MSA has diversifiedits safety business into almost all the manufac-turing industry segment present in India and istoday one of the most preferred safety brandin India.

MSA India is now a 100% owned affiliate com-pany of MSA International Pittsburgh with itslatest state-of-the-art corporate office at theECOSTATION in 2nd para. The company has un-dertaken a major re-vamping process tostreamline its Sales, Distribution and Market-ing functions with a focus on providing theWorld Standard products at local affordableprices.

With "The Central Logistics Hub" (CLH) in NaviMumbai and "The Technical Support Centre",Navi Mumbai and Ecostation in Kolkata, ourcompany is ready to cater to the growing needof its customers in India.

Our MissionMSA's mission is to see to it that men andwomen may work in safety and that they, theirfamilies and their communities may live inhealth throughout the world. Our vision is tobe the leading innovator and provider of qual-ity products, related technologies and servicesthat protect people's health, safety and the en-vironment in all key markets MSA serves.

1

Total ProtectionIntegrated Safety Solutions




Hearing Protection

Fall Protection


Permanent Gas Detection

This catalog gives you an overview on MSA’s productportfolio in India:

Personal ProtectiveEquipment &Gas Detection

Fire Service

Utilities

Construction

Government

Transportation

Oil, Gas, Petrochem

Mining

General Industries

MSA’s comprehensive product portfolio ranges from simple to complexhigh-techn solutions. The great breadth of technologies, products andservice we offer is unique to the market.

MSA products are designed to ensure the integrated system compati-bility of individual safety and gas detection products. MSA’s ownsoftware integrates perfectly into our range of hardware.

Thermal Imaging

2

Supplied Air RespiratorsIndependent of the Ambient Atmosphere

MSA offers various Supplied Air Respirators (SAR) that function inde-pendently of the ambient air.

The self contained breathing apparatus system, including the AirGo andAirMaXX models, is independent of the ambient atmosphere, meaningthe user is not tied to a specific location. They offer a wide variety of fea-tures and applications.

MSA offers the monitoring systems alpha Personal Network with tele-metric capabilities and the personal alert safety system motionSCOUT.

MSA’s chemical oxygen apparatus are ideal for escape/ or working ap-plications wherever outbreaks of toxic gases, particles or the suddenoccurrence of oxygen deficiency are to be expected.

The Airline system is designed for applications of extended duration;e.g. in confined spaces. This system connects to an external air supply,offering cost effective protection. If you have to be prepared for situa-tions where sudden oxygen deficiency can occur, an MSA compressedair escape device is an option well worth considering.

3

Breathing Apparatus

AirXpressIn building the AirXpress, an SCBA system made for tight budgets, MSA has concentrated onthose features most essential for safety and performance. To meet the specialised demandsof industry and emergency response, the MSA AirXpress comes in two configurations: AirX-press Industrial and AirXpress Fire.

The AirXpress first-stage pressure reducer is the same one used in all MSA systems. Thispatented and choice component distinguishes itself through reduced parts and low mainte-nance, which translates into reduced cost of ownership. Like all other MSA SCBA systems, allcomponents on the AirXpress are designed to last long in rugged circumstances. They areEN 137:2006 approved to withstand high temperatures, flames and rough handling plusthey are intrinsically safe and ATEX-approved for zone 0 environments.

AirXpress Fire• BD Backplate: word-renowned design• AutoMaxx-AS demand valve• Gauge cap• Pneumatic systems based on the alpha platform• Padded harness, with reflective logo on the

shoulder strap• Integrated transponder for storage control


4

Part Number Description

I01AX0020001 AirXpress FIRE backplate with AutoMaXX DV, 3S PS MaXX Mask withLight Weight Steel Cylinder and HBA 10 valve

I01AX0020002 AirXpress FIRE Backplate with AutoMaXX DV, 3S PS MaXX Mask with-out Cylinder & Without Valve

I01AX0020003 AirXpress FIRE backplate with AutoMaXX DV, 3S PS MaXX Mask withCarbon Composite Cyl and HBA-10 Valve

I01AX0020004 AirXpress FIRE Backplate with AutoMaXX DV, 3S PS MaXX Mask withCarbon Composite Cyl and MSA Valve

I01AX0020005 AirXpress FIRE Backplate with AutoMaXX DV, 3S PS MaXX Mask with6Ltr Steel cylinder and MSA Valve

I01AX0020006AirXpress FIRE with 2nd Man connection backplate with AutoMaXXDV, 3S PS MaXX Mask with Light Weight Steel Cylinder with HBA-10valve

10111838 AirXpress Fire Version with AutoMaxx Demand Valve Back Plate

10109407 AirXpress Fire Version with AutoMaxx Demand Valve Back Plate with2nd Coneection

AirGo SeriesWhen you are looking for a strength carrier for firefighting and for a wide range of mainte-nance or rescue operations, the AirGo Series of Breathing Apparatus is ready for deploy-ment. Its rugged reliability, flexibility and great value make it a popular choice for firebrigades, plant, sub-surface or offshore use. Weight is distributed evenly and kept close toyour body to reduce stress and fatigue.

The AirGo SCBA is specifically designed for emergency response and escape. On ships orindustrial facilities, fire fighting where such units are mandatory, the AirGo is an obviouschoice. The lung governed demand valve AutoMaXX-AS is fixed to the medium pressureline. The nofrills system keeps costs at a minimum without sacrificing safety. The alpha Sin-gle Line pneumatic system integrates warning signal, second connection and gauge in aneasily accessible manifold at your chest. The optional alpha Personal Network offers ex-tended electronic and telemetric monitoring and communication capability. The vital pneu-matic and carrier components are the same as those used in the highend MSA BA Sets,making AirGo a fully-fledged device for the toughest applications including firefighting.Various harness options ranging from very low cost com harness to high cost Pro harnessavailable with the set Approved as per EN137 Class 2.

AirMaXXThe AirMaXX SCBA combines premium eronomic features with advanced technology to pro-vide the best experience in SCBA wearability available today. The ergonomically designedand optimally balanced AirMaXX backplate is adjustable to fit all body sizes. This works inconjunction with the premium S-swing shoulder pads and swivelling hip belt to distributeweight evenly while increasing freedom of movement. Stress and fatigue are reduced asyou perform your job without restrictions. The AirMaXX stays with you even when you areturned upside down.

The alpha Single Line pneumatic system integrates warning signal, second connection andgauge in an easily accessible manifold at your shoulder. The optional alpha Personal Net-work offers further electronic and telemetric monitoring and communication capability. Ifyou are using your SCBA frequently, for long periods at a time or require absolute concen-tration in your work, the AirMaXX is the system of choice. Approved as per EN137.


10060803 AirMaXX SL Back Plate

10084767 AirMaXX CL S with ICU Back Plate

10023688 AutoMaXX AS Demand Valve


5


10086572 AirGo Compact with AutoMaXX Demand Valve Back Plate

10086571 AirGo Pro SL Black Plate

10091546 Airgo pro CL with ICU, bumper, retainer and long strap

I01AG0010017 AirGOPRO SL SCBA set with AutoMaXX-AS D. Valve,3S-PS-MaXXMask with 6.8Lt CFK cylinder and valve and carrying case

alphaSCOUT & alphaMITTERThe alphaMITTER, a short-range transmitter on the SCBA back plate sends air pressure datato the alphaSCOUT every second. Because the wireless alphaSCOUT is independent of theback plate, the number of units needed by a brigade can be reduced by up to 75% - a dramatic saving in investment.

Ask your MSA sales representative for more information.

alphaBASEForthe base station you can choose between several sender/receivers. The alphaBASE stan-dard works in combination with any Pc. An external aerial with magnetic foot can optionallybe used for vehicle mounted applications. A battery-powered version of the alphaBASE orthe alphaBASE standard can also be used with the xplore TABLET PC. The combination bat-tery-powered alphaBASE and xplore TABLET PC allow full freedom of movement for mobileapplications.

MotionSCOUT – Personal Alert Safety Systemmotion SCOUT The next generation of standalone personal alertsafety systems motion SCOUT detects the cessation of bodily movement and activates anautomatic alarm. For enhanced safety the alarm can be activated manually as well. Withhighly visible LEDs and an alarm volume of at least 95 dB it helps to locate the person indanger.

The sensitive, electronic motion sensor recognises all normal body movements. A bicolourLED clearly shows the readiness of the unit. Maintenance-free and durable [IP 67] it guaran-tees a great cost-performance-ratio.

motion SCOUT is extremely simple to use and can be easily affixed to the shoulder strap orhip belt.

Respiratory Protection Enhancements & Monitoring

Performance & Ergonomics


6


Please contact MSArepresentative forexact configuration

Back plate with Telemetry options with alphaMITTER

10058212 alphaSCOUT TM –Telemetry Module (complete set incl. long-dis-tance radio,batteries, alphaTAG)

10058214 alphaBASE Standard (incl. power supply, direct and external aerialwith magnetic foot and software)

10126876 DVD : Sotware alphaCONTROL

10086118 Alpha HUD

10068805 xplore TABLET

10065875 TAGwriter (incl. USB cable)


10088033 motionSCOUT T [temperature sensor]

10088031 motionSCOUT Personal Alert Safety System

Accessories and Spares

SCBA Accessories

Other Supplied Air Equipments


7


10031422 3S PS MaXX Full Face Mask

10031385 Ultra Elite PS MaXX Full Face Mask

276830 Light Weight Cylinder with Cylinder Valve (4073934)

276831 Light Weight Steel Sylinder with Cylinder Valve (HBA-10)

276820 CARBON COMPOSITE CYLINDER W/O VALVE 6.8 ltr * 300 bar

4073934 Cylinder Valve

4090700 Integrated Control Unit (ICU)

10049021 CARRYING CASE FOR BA Set

10045764 Respihood Complete

276822 CARBON COMPOSITE CYLINDER 6.8 ltr x 300 bar With MSA valve

L150010 Self Locking Wheel operated valves for Breathable air cylinder, HBA-10


10020421 S-CAP-AIR 15 w/o Cylinder

9013792 3 Ltr 200 Bar Steel Cylinders required for S-CAP AIR w/o Valve

10064644 ESCAPE HOOD, S-CAP in Carton

10064645 ESCAPE HOOD, S-CAP in Wall Box

276824 3ltr 300 bar carbon composite cylinder for S cap air

Ambient-Air-Dependant Protection

Filtered respiratory protection is dependent on the ambient atmos-phere. Local regulations concerning the use of filtering devices must beobserved.

In order to use filtering respirators, the type, properties and compositionof the hazardous agent in the ambient air must be known. The oxygencontent in the inhalation air must be sufficient (for example according toGerman regulations: at least 17 vol %).

When using particle filters, no hazardous gases may be present; whenusing gas filters, no hazardous particles. In case of doubt, a combined filter must be used.

The most frequently used filters are of the ABEK type, which protectagainst many hazards at the same time, due to the wide range of pro-tection that they provide. Based on EN 14387, these filters have an application range covering the code letters A, B, E and K. Benefits forthe user include: safe selection, no mix-ups, economical procurement,simpler stockkeeping.

High-grade multiple range filters have an even greater sphere of appli-cation, e. g. the combined filter 93 ABEK CO NO Hg/St or 93 A2B2E2K2Hg/St.


8

Air Purifying RespiratorsProtection Against Gases & Particles

3S Basic PlusThe 3S Basic Plus is provided for use with respiratory protective filters [screw-type filterswith thread to EN 148-1], assisted and non-assisted fresh air breathing apparatus, air-linesystems and Powered-Air-Purifying-Respirators.

It is not approved for use by fire departments or as face piece in combinationwith compressed-air breathing apparatus [certified to EN 136, Class 2].

The 3S Basic Plus faceblank is made of a skin-compatible and largely age-resistant naturalrubber formulation. It offers the same good properties the 3S mask series is known for. Theacrylic [PMMA] lens is scratch-resistant and almost unbreakable. Moreover it offers a goodfield of vision. The visor is fitted with a white lens frame and is easy to replace.

Full Face Masks


D2055790 3S Basic Plus Full Face Mask

Half Face Masks

Advantage® 400 Series Half Mask RespiratorsThe Advantage 420 Half-Mask Respirator is uniquely designed to incorporate user-friendly features including maximum comfort, improved donning and fit, enhancedsafety, and reduced maintenance cost. The Advantage 420 Respirator has a Patent-pending UniBond over-molded one-piece silicone facepiece, helping to eliminate pos-sible leak paths which may be present in other competitive silicone half-maskrespirators. All plastic MSA Advantage cartridges as well as metal MSA Comfo®threaded cartridges can be used with the Advantage 420 Respirator.

Maximum Comfort• Head harness and facepiece integrate well with other PPE• Drop-down harness position allows respirator to be removed while retaining headprotection• One-piece ComforTop cradle headband eliminates pressure points when head pro-tection is worn Improved Donning and Fit• AnthroCurve II multi-ethnic face seal based upon new proposed NIOSH test panel im-proves fit-testing among diverse workforce• Patent-pending lock-down harness position allows a personal fit without further useradjustments

Part Number Description10102183 Advantage 420 Half Face Respirator medium

9


10

Advantage® 200 LS Half Mask RespiratorThe Advantage 200 LS Respirator's Lighter and Softer facepiece is made from a clearblue formulation of thermoplastic rubber to give workers more comfort and stabilitythan ever.

Extensive anthropometric research led to the Advantage Respirator's unique design.MSA's engineers examined facial form data of over 8,000 people and, with CAD technol-ogy, developed the Anthrocurve! Sealing Surface, which instantly conforms to eachwearer's uniquefacial characteristics.

The unmatched fit and comfort start with a soft, pliable combination of rubber andplastic that provide a virtually customized fit. These are key components in the patentedMultiFlex® System that equalizes pressure on the faceseal area, while delivering excep-tional stability, so the respirator will not collapse during wear.

Part Number Description815444 Advantage 200 Half Face Respirators

Respiratory FiltersMSA offers a wide range of filters, for protection against organic or inorganic gases &vapours according to the required protection range. Gas filters are available in Class 1 & 2,Single or multiple range filters (ABEK). Combined filters can be used for protection againstorganic & inorganic gases & vapours, according to the required the protection range asagainst solid & liquid particles.

The service time of respiratory filters depends on the conditions of use. For gas or combinedfilters that are used against gases, the end of a filter's service life can usually be detected byodour, taste or irritation during inhalation. Some filters have a specified maximum servicetime [CO filter cartridges, combined filters 89 Hg/St].

For particle filters or combined filters that are used against particles, the end of service timecan be detected by an increase in inhalation resistance. With combined filters - dependingon the predominant protective function - both criteria must be observed. Particle filtersmust only be used once against radioactive contaminants, spores, bacteria, virus and prote-olytic enzymes.

Part Number Description10098113 Gas Filter 90 AB

10115320 Gas Filter 90 K

10098114 Gas Filter 90 ABEK

10098112 Gas Filter 90 ABEK2

10097996 Combined Filter 92 ABEK2/St

10097232 93 ABEK2Hg/St combined filter

10115315 Comb. Filter 93ABEK-CO-NO-Hg/St

Respirator CartridgesDesigned for easy installation, Advantage cartridges use the latest bayonet-style mountingdesign. Featuring a low lug height and lead-in connectors, the cartridges lock into placewith a single twist. An advanced engineering design makes negative pressure fit-testingeasier to perform.

The complete Advantage line of particulate, chemical and combination cartridges are ap-proved under 42 CFR Part 84. The Occupational Safety and Health Administration (OSHA) re-quires fit tests to ensure proper fit for workers who use respirators.

Filter cartridges protect against dusts, particles and mists. Chemical cartridges protectagainst gases and vapors. Combination cartridges deliver protection from both particulateand gaseous contaminants. All cartridges are interchangeable between the Advantage 200and 3000 respirators and are color-coded. Most are incinerable.


11

Advantage® 3000 RespiratorEnhances worker performance through a design that allows even lower breathing resist-ance, a standard nosecup that reduces fogging and a soft, pliable silicone facepiece. Ascratch resistant, wraparound lens engineered to be optically correct eliminates distortionfor superior visibility and peripheral vision. Advantage 3000 uses the same cartridges andfilters as the Advantage 200LS respirator.

Pre-adjustable straps deliver a consistent fit, time after time. The preset upper straps pre-vent uncomfortable snags during donning and doffing and provide a tighter, more secureseal. Wearers can choose the new European-style Advantage harness, which dons like acatcher’s mask.

Exceeds the performance requirements of ANSI Z87.1. Designed to meet the National Insti-tute for Occupational Safety and Health (NIOSH) and EN standards.

Part Number Description10028995 Advantage 3000 Full Face Respirators

Part Number Description815355 GMA cartridge for Advantage Respirator (Pack of 02)

815357 GMC cartridge for Advantage Respirator (Pack of 02)

815359 GME cartridge for Advantage Respirator (Pack of 02)

815361 MERSORB CARTRIDGES FOR ADVANTAGE (Pack of 02)

815362 GMA P100 CARTRIDGES FOR ADVANTAGE RESPIRATOR (Pack of 02)

815364 GMC P100 cartridge for Advantage Respirator (Pack of 02)

815366 GME P100 cartridge for Advantage Respirator (Pack of 02)

815368 MERSORB P100 Cartridge for Advantage Respirator (Pack of 02)

815392 Reusable Snap on cover for N95 (Pack of 02)

815394 N95 Snap on Prefilter (Pack of 10)

815397 R95 Snap on Prefilter (Pack of 20)

815401 Reusable Snap on Cover for R95 (Pack of 02)

818344 FLEXI-FILTER P100

815356 GMB cartridge For Advantage Respirator (Pack of 02)

697384 TOWELETTE,INDIVID. PKGD.

697383 TOWELETTES, 100/BX

697382 TOWELETTES,CANISTER OF 220


12

Powered Air Purifying Respirators (PAPRs)OptimAir 3000The OptimAir 3000 PAPR system allows you to breathe normally while you work. Your com-fort,well-being and ability to perform effectively are greatly enhanced. Filters also lastlonger. The microprocessorcontrolled, variable-speed motor guarantees an optimumamount of air in your headtop (mask or hood) – even as your breathing rate changes duringmore strenuous tasks. In many situations it is not even necessary to maintain an airtightseal. The pressure differential causes airflow to travel continuously from your face to theoutside environment, preventing unfiltered air from entering your headtop.


10049557 OptimAir 3000 PAPR (Standard Blower 130/ min, with comfort belt.Standard charger, standard battery)

10051810 OptimAir Mask with Hose

10051806 OptiHood Full

10049631 OptiHood Hose

Part Number Description10049632 Particle Filter (Pack of 10)

10049637 A2 TABTEC Filter (Pack of 10)

10049635 ABEK Filter (Pack of 10)

Accessories and Spares

Escape Devices

miniSCAPEminiSCAPE is a one-time use escape device fitting into the pocket of any work clothing orcarried at the belt. In case of emergency it can be donned very quickly and is immediatelyoperational. Using the TabTec filter, it offers an ABEK-5 protection.

S-CapIt has been proven that most victims during dramatic circumstances due to a fire do not getinjured by heat or flames but from smoke and gases. S-CAP is an escape hood especiallydesigned to protect persons endangered by smoke and gases generated by fires. The mostdangerous of them is carbon monoxide. S-CAP provides an effective protection for eyes,head and especially the respiratory tract, and thus persons can rescue themselves with littlerisk.

Part Number Description10038560 miniSCAPE

Part Number Description10064644 ESCAPE HOOD, S-CAP in Carton

10064645 ESCAPE HOOD, S-CAP in Wall Box

Versatility. Reliability. Comfort.

Due to their importance and sensitivity, the protection of the head, face,and in many working environments is a paramount consideration.

Whether required for the special, most demanding requirements of fire-fighters, rescue teams and policemen or the wide field of industrial use,MSA provides a huge selection of the best head protection, integratedor attached face shields, advanced systems for communication andhearing protection as well as fashionable protective eyewear.

These products are extremely reliable, comfortable and designed towork perfectly in conjunction with all MSA equipment, e.g. respiratoryprotectors.

Furthermore, a complete range of accessories is available to suit yourindividual needs.


13

Safety & Sight in Perspective

V-Gard® Protective Caps and Hatsfrom MSA consist of a polyethylene shell and suspension system working together as a pro-tection system.V-Gard headwear features advanced styling in either cap or hat styles, V-Gard Caps and Hats meet or exceed the applicable requirements for a Type I helmet (topimpact) as outlined in ANSI Z89.1 1997,Class E and G.

Head Protection

14


9100920 Spare Suspension STAZ-ON, PERFORATED SWEATBAND,FOR HDPESHELL

9100820 Spare Suspension FAS TRAC II Perforated SWEAT BAND ,FOR HDPESHELL

Spares

Part Number DescriptionL150009 Chin Strap For V Gard (For China Make FasTrac n SOS)

9100001 D CHIN STRAP,2 POINTS, attached to Shell

9100008 D CHIN STRAP,2 POINTS, attached to suspension

Add Ons



10154322 MSA CAP V GARD HDPE WHITE WITH STAZON SUSPENSION,Perfo-rated SWEAT BAND

10154323 MSA CAP V GARD HDPE YELLOW STAZON SUSPENSION,PerforatedSWEAT BAND

10154324 MSA CAP V GARD HDPE ORANGE WITH STAZON SUSPENSION,Perfo-rated SWEAT BAND

10154325 MSA CAP V GARD HDPE RED WITH STAZON SUSPENSION,PerforatedSWEAT BAND

10154326 MSA CAP V GARD HDPE BLUE WITH STAZON SUSPENSION,PerforatedSWEAT BAND

10154327 MSA CAP V GARD HDPE GREEN WITH STAZON SUSPENSION,Perfo-rated SWEAT BAND

10154341 MSA CAP V GARD HDPE RED WITH SUSPENSION FAS TRAC II WITHPerforated SWEAT BAND

10154342 MSA CAP V GARD HDPE BLUE WITH SUSPENSION FAS TRAC II WITHPerforated SWEAT BAND

10154343 MSA CAP V GARD HDPE GREEN WITH SUSPENSION FAS TRAC II WITHPerforated SWEAT BAND

10154328 MSA CAP V GARD HDPE WHITE WITH SUSPENSION FAS TRAC II WITHPerforated SWEAT BAND

10154329 MSA CAP V GARD HDPE YELLOW WITH SUSPENSION FAS TRAC IIWITH Perforated SWEAT BAND

10154330 MSA CAP V GARD HDPE ORANGE WITH SUSPENSION FAS TRAC IIWITH Perforated SWEAT BAND


15

Vented V gard 500 Caps provide cooling vents for improved air circulation and comfort. Vented V gard 500 Capsmeet or exceed all applicable requirements for a Type I helmet (top impact) as outlined inANSI Z89.1-2003. Non-vented meets Class E and Vented meets Class C.

Part Number Description10034018 Vented V gard 500 Caps With 4 Point Fas Trac Ratchet Suspension (White)

10034019 Vented V gard 500 Caps With 4 Point Fas Trac Ratchet Suspension (Blue)

10034020 Vented V gard 500 Caps With 4 Point Fas Trac Ratchet Suspension (Yellow)

10034022 Vented V gard 500 Caps With 4 Point Fas Trac Ratchet Suspension (Red)

10034023 Vented V gard 500 Caps With 4 Point Fas Trac Ratchet Suspension (Green)

10034026 Vented V gard 500 Caps With 4 Point Fas Trac Ratchet Suspension (Orange)

Spare suspension for V gard 500

Part Number Description10034966 4-POINT FAS TRAC SUSPENSION (Spare) for Vented V gard 500 caps

Part Number Description81391 Chin Strap for V Gard Advance

ADD Ons

Part Number Description475369 V Gard Hat Non-Slotted WHITE w/Fas-Trac Suspension

475368 V Gard Hat Non-Slotted BLUE w/Fas-Trac Suspension

475370 V Gard Hat Non-Slotted GREEN w/Fas-Trac Suspension

475371 V Gard Hat Non-Slotted RED w/Fas-Trac Suspension

496075 V Gard Hat Non-Slotted ORANGE w/Fas-Trac Suspension

475366 V Gard Hat Non-Slotted YELLOW w/Fas-Trac Suspension

Full brim hatsThese V-Gard® Protective Hats are the best-selling in North America. Polyethylene shell andself-adjusting crown straps provide comfortable, lightweight protection.

Part Number Description697259* VersaLite Helmet Light with 2 AA alkaline batteries

697261** Stealthlite Helmet Light (batteries not included)

814322 Light holder for slotted cap, no metal parts

Helmet LightsMSA offers two helmet lights that fit into our special cap adapters, Both of the lights are FMand CSA-approved for intrinsic safety, and are non-incendive.

The V-Gard Accessory System is a full line of frames, visors and chin protectorsthat meet many global standards, including ANSI/ISEA Z87.1-2010, CSA Z94.3,EN166 and AS/NZS 1337, as well as many local standards.Convenient. Compliant. Compatible. That's the V-Gard Accessory Systemfrom MSA.Introducing the V-Gard Accessory System – frames, visors,and chin protectors designed for MSA V-Gard Helmets.Reliable accessories offering the same high standards ofprotection as the V-Gard Helmet. And for those who preferother MSA helmets (such as the Skullgard® Helmet), auniversal version of the V-Gard Frame fits any MSA slottedor non-slotted helmet.

16


V-Gard Accessory System

FramesThe V-Gard Accessory System offers helmet-mounted frames for various work conditionsand MSA helmets. The sloped design allows liquids, chips and other materials to slide offthe frame and away from the line of sight. Each frame, whether used with or without debriscontrol, meets the applicable requirements for ANSI/ISEA Z87.1-2010, EN 166, CSA Z94.3and AS/NZS 1337, as well as many local standards.

Part Number Description10115822 V-Gard UNIVERSAL FRAME FOR CAPS, WITH DEBRIS CONTROL

10124426 V-Gard UNIVERSAL FRAME FOR CAPS, ET, WITHOUT DEBRIS CON-TROL

V-Gard Frames for Slotted MSA Caps

V-Gard Universal Frames for Slotted or Non-Slotted MSA Caps


10115730 V-Gard FRAME FOR MSA SLOTTED CAPS, WITH DEBRIS CONTROL

10121266 V-Gard FRAME FOR MSA SLOTTED CAPS, WITHOUT DEBRIS CON-TROL3

10121267 V-Gard FRAME FOR MSA SLOTTED CAPS, ET, WITHOUT DEBRIS CON-TROL

V-Gard Frames for MSA Full-Brim Hats

Part Number Description10116627 V-Gard FRAME FOR HATS

10116628 V-Gard FRAME FOR HATS, ET

HeadgearV-Gard Headgear is a brow guard that in combination with the wide range of V-Gard Visorscomprehensive face protection system. Featuring a durable and stylish HDPE frame and thechoice of over 20 visors it is ideal for many applications. With the unique 3-point visor loadsystem visors are fitted or removed easily and quickly. Adjustable to all head sizes and withtwo comfort sweatbands all day comfort is for sure.

Part Number Description10127061 V-Gard Headgear Standard, without visor

10127062 V-Gard Headgear Elevated Temperature, without visor

10127065 Replacement sweatband brow, 5 pcs


17

Visors

Part Number Description10115836 CLEAR, PC, SIDE CONTOURS PC 8" (20.3 cm) x 17" (43.2 cm) x .04" (1.02 mm).

10115863 CLEAR, PC, SIDE CONTOURS PC,CLR,MEDxSTDxLTW 9.5" (24.1 cm) x 17" (43.2cm) x .04" (1.02 mm).

10115839 CLEAR, PC, SIDE CONTOURS, AF/AS 8" (20.32 cm) x 17" (43.2 cm) x .06" (1.52mm).

10115854 GREEN TINT, PC MOLDED, AF/AS10.375" (26.4 cm) x 17" (43.2 cm) x .098" (2.5mm).


10115844 CLEAR PC, MOLDED, AF/AS 9.25" (23.5 cm) x 17" (43.2 cm) x .098" (2.5 mm).

10115845 GREEN TINT PC, MOLDED, AF/AS 9.25" (23.5 cm) x 17" (43.2 cm) x .098" (2.5mm).

10115850 GREEN TINT PC, REFLECTIVE COATING, MOLDED 9.5” (24.1 cm) x 17.75" (45.09cm) x .07” (1.78 mm).

V-Gard Visors for Chemical and Splash ApplicationsThese propionate visors are for chemical and splash applications, and are ideal for use inmanufacturing plants, laboratories and other industrial applications that demand face pro-tection against impact hazards, abrasive particles, splash and spray.1 Molded V-Gard Visorsare manufactured with hand-polished molds for unsurpassed, distortion-free optical clarity.

V-Gard Visors for Elevated Temperature Applications These PC visors help keep workers comfortable in environments such as steel/smeltingplants where they are exposed to high levels of heat and/or excessive glare. Our V-Gard Vi-sors are engineered for heavy duty use and are thicker than most visors in the marketplace,which not only helpsensure impact resistance, but also reduces heat warping.

V-Gard Visors for General Purpose Applications These visors are made of durable polycarbonate or mesh, and help protect wearers from fly-ing debris, splash or spray1. All V-Gard Visors for generalpurpose can be worn with cap-mounted earmuffs.

Part Number Description10115855 CLEAR PROPIONATE, MOLDED 8" (20.3 cm) x 17" (43.2 cm) x .098" (2.5 mm).

10115851 CLEAR PROPIONATE, MOLDED 9.25" (23.5 cm) x 18" (45.7 cm) x .098" (2.5 mm).

18


V-Gard Visors for Welding Applications These PC visors help protect against damage from impact and infrared (IR) radiation. De-signed for welding, metal pouring, gas soldering, and light cutting/brazing, they’re engi-neered for heavy-duty use. They are thick to help prevent warping from heat or weldspatter.


10115859 SHADE 3 IR, PC, MOLDED 8” (20.3 cm) x 17.25” (43.8 cm) x .07” (1.8mm).

10115861 SHADE 5 IR, PC, MOLDED 8” (20.3 cm) x 17.25” (43.8 cm) x .07” (1.8mm).

V-Gard Visors for Arc Flash Applications These PC visors are engineered to help protect against impact and dangerous arc flash haz-ards. Perfect for electrical workers and electricians workingwith high-voltage connections.Rated to 12.9 cal/cm2 when tested to ASTM F2178-2008 (ref. NFPA 70E-2012, Hazard RiskCategory 2), and when worn with a V-Gard Hard Hat (PN 475358) and V-Gard Frame (PN10121266).


10115847 ARC, PC, MOLDED 9.25” (23.5 cm) x 18” (45.7 cm) x .065” (1.7 mm).).

Accessories

Part Number Description10115827 STANDARD CHIN PROTECTOR

10117496 Slot adaptors (2 pair)

10116539 Debris control for V-Gard Cap Frames

10117495 Heavy duty rubber strap for V-Gard Universal Cap or Hat Frames.

MSA offers a wide range of Eye Protectors & Soft frame Goggles to effectively fit most facialcontours. Large, one-piece, .060-inch-thick polycarbonate lens provides wide, undistortedfield of vision. Optional Anti-Fog Coated Lenses are available for work involving high humid-ity, temperature changes or greater worker exertion. The scratch-resistant coating is unaf-fected by most regularly used industrial chemicals.

Industrial Protective Eyewear is designed for protection against impact hazards and/or fly-ing particles, dust, sparks, and glare. Industrial Protective Eyewear provides excellent side-and front-impact protection while still being comfortable to wear. All MSA Eye protectorsconforms / approved to applicable requirements of EN166 & ANSI Z87.1-2003.

Eye Protection

Part Number Description1000700 FL 250 HC Clear Frame Clear Lens

1000701 1900-HC Clear Frame, Clear HC Lens

1000703 1900-HC Black Frame Smoke Lens

1000704 1071-HC Black Frame, Clear HC Lens

1000705 1071-HC Black Frame, Smoke Lens

1000706 1090-AF Black Frame Clear Lens

1000708 2047-W None Clear Frame, Clear Lens

1000716 1090-HC Black Frame, Clear HC

1000722 GIV-2000 None Clear Frame, Clear Lens

1000725 1090-HC Black Frame, Smoke Lens Spectacle

1000726 5500-HC Slate Frame, Smoke Lens

1000727 5500 Clear Lens Spectacle

1000728 5400-TA 30 HC Over Spectacle

1000732 GIV-2000 AF Clear Frame, Clear Lens

1000737 1860-HC Clear Frame, Clear Lens

1000738 1860-HC Grey Frame, Smoke HC Lens

1000769 GIV 2400 AF Grey Frame, Clear Lens

1000779 GIV-2100 None Clear Frame, Clear Lens

1000788 1262-AF Clear Lens

1000789 1262-AF Smoke Lens


19

Comfort & Performance by Design

Guarding people against the daily hazards of noise is of paramount con-cern in countless industries. The challenge is to balance personal attenu-ation devices with comfort and the ability of communication andlistening to music, so that workers will wear their hearing protectors allthe time.

The most important factors to consider when selecting hearing protec-tion are the right performance and wearer comfort.

Whether working in noisy environments, for just a few minutes, or forseveral hours – hearing protection is always needed. A worker whotakes off his hearing protection because he does not feel 100% comfort-able is a worker at risk.

MSA offers a wide range of passive and electronic ear muffs as well asear plugs for DIY (Do-It-Yourself ) use, construction, industry, police andother applications. All products are comfortable hearing protectors, de-signed to prevent the wearer from feeling isolated.

All products are comfortable hearing protectors, designed to preventyou from feeling isolated, thereby encouragaing you to use them andso protecting your hearing for the rest of your life. Noise Reduction Rat-ing (NRR) is third-party tested in accordance with ANSI S3.19-1974 andEN352-3. Also meets CSA Z94.2.

Hearing Protection

20

21

Comfort & Performance by Design

Sound Control®Sound Control Cap Models are designed for easy attachment to slotted MSA Caps and helpto reduce the effects of excessive noise. HPE, EXC, XLS, Economuff headband & cap modelsare designed specifically for very high noise levels and these powerful muffs are ideal for airfields, power plants and other areas with intense noise. Light weight & comfortable earpads ensures all day wearing without fatigue & durable design provide protection in dirtyenvironment. Noise Reduction Rating may vary depending on various MSA models.

Hearing Protection

Hearing Protection

Part Number Description10004291 Economuff 20 DB

10061229 EARMUFF, EXC, HEADBAND 26 DB

10061271 EARMUFF,HPE,HDBAND 31 Db

10061535 Passive Hear Protn Xls For Slotted Caps

LEFT/RIGHTThe left/RIGHT ear muffs are different from all existing hearing protectors. Individual muffs,especially designed for the left and right ear, compensate for the asymmetric position of theearson the head. The revolutionary headband design and the thinner, more flexible sealingrings ensure anoptimal fit for wearer comfort. Large muffs provide more room for the ear to guarantee theright protection for all shapes and sizes of ears.Unique to the market left/RIGHT considers the anatomical individuality of the users. Theleft/RIGHT concept offers various options depending onthe application and individual preferences.All options can be combined: low, medium or high attenuation; headband or helmetmounted;yellow, blue, white or grey. Right protection for the right purpose.

Part Number Description10087399 left/RIGHT– HIGH headband model yellow

10087421 left/RIGHT– HIGH headband model White

10087422 left/RIGHT– HIGH helmet mounted model yellow

10087424 left/RIGHT– HIGH helmet mounted model White

Hearing Protection

22

Electronic ProtectionHow can users be encouraged to wear hearing protectors when working in harmful noise ?There are countless sources of noise directly linked to machinery and industrial processes :electrical machinery, tractors, industrial ventilation systems, diesel engines, chainsaws,wood working equipment, heavy industrial machinery, pumps and compressors, ... it is im-portant that the hearing protection used provides sufficient noise attenuation to protectthe user, but not so much that users are isolated from their auditory environment. Excessiveprotection can prevent users from hearing their workmates, alarms and other importantsignals.The challenge presented by electronic hearing protection devices is the necessity of balanc-ing the requirements of hearing protection with user comfort, ease of communication andthe desire to listen to music. left/RIGHT is a range of hearing protectors with built in electronic functions that offers pro-tection, communication and pleasure.

Part Number DescriptionSOR85502 WW CutOff helmet mounted

SOR45000 WW CutOff Headband

10111789 left/RIGHT CutOff Pro Headband Yellow

10108383 left/RIGHT CutOff Pro Headband Blue

10111823 left/RIGHT CutOff Pro Helmet mounted Yellow

10111826 left/RIGHT CutOff Pro Helmet Mounted Blue

Others

Part Number Description10094605 Hygiene kits ,LEFT/RIGHT ELECT. EARMUFFS

Fall Protection

Guarding people against the daily hazards of noise is of paramount con-cern in countless industries. The challenge is to balance personal attenu-ation devices with comfort and the ability of communication andlistening to music, so that workers will wear their hearing protectors allthe time.

With over 40 years of experience, MSA now offers a new wide range ofhearing protectors with built-in electronics - from basic functions tohigh-specification communication devices.

All products are comfortable hearing protectors, designed to preventyou from feeling isolated, thereby encouragaing you to use them andso protecting your hearing for the rest of your life. Noise Reduction Rating (NRR) is third-party tested in accordance with ANSI S3.19-1974and EN352-3. Also meets CSA Z94.2.

Durable & Versatile

23

Fall Protection

Durable & Versatile

Workman® Full Body HarnessThe Workman Harness provides comfortable protection, due to its lightweight componentsand durable webbing. The vest-style harness, with optional hip D-Rings for work position-ing, fits a wide range of body types and sizes. Color-contrasting thigh and torso straps sim-plify donning.

Features include:• Economical• Abrasion-resistant, strong, durable webbing• Yellow polyester webbing for high visibility• Web retainer collars to keep excess webbing neat• Easy to don and adjust• Choice of Qwik-Fit™ or Tongue-Buckle leg straps for easy adjustment


10115527 WKM Light Full Body Harness EN 361

10115542 MSA Workman Premier Full Body Harness, medium, Qwik-fit legstraps, D-ring

24

MSA Energy-Absorbing LanyardsMSA energy-absorbing lanyards are lightweight with a lowprofile body. The shock ab-sorber includes a clear, durable protective cover over the labels to increase service lifeand allow for easy inspection.

Features include:• Tear-tape design to keep fall arrest forces below 900 lbf.• Choice of single or twin-leg configurations• Choice of adjustable or tie-back configurations Meets ANSI Z359.1-1992 (R1999), ANSI

A10.32, applicable OSHA regulations, and is certified to CSA Z259.11-05 E4

Restraint LanyardsRestraint lanyards are primarily used for travel restriction andwork positioning. Lanyards for travel restriction are used torestrain a worker from reaching a fall hazard. Lanyards for workpositioning are used for stabilizing a worker at an elevation.They can be ordered in fixed or adjustable lengths. Each lanyardcomes with a forged steel, zinc-plated self-locking snaphookattached to each end. Meets ANSI and OSHA standards.

Part Number Description10115742 Single Leg EA LAN,Web,2m,adj,StScCara-StScaf

10115751 Twin Leg EA LAN,Web,2m,adj,StScCara-StScaf

10115778 Twin Leg EA LAN,Rope,1.5M,StScCara-StScaf

10115800 MSA Workman Restraint Lanyard, webbing, 2 m adjustable length,aluminium screwgate carabiner

10115796 MSA Workman Restraint Lanyard, webbing, 1.5 m fixed length,aluminium screwgate carabiner

Self-Retracting LanyardsMSA has set a new standard in the mechanical fall protection market with the Self-Retract-ing Lanyard (SRL). Never before has the market seen such a state-of-the-art device with somany standard features. With its solid design and fast-acting brake mechanism, you can beconfident that the SRL's will be there for you when you need it most.

All MSA SRL's feature:• A durable, engineered thermoplastic housing to increase service life.• Rugged, impact-absorbing protective bumpers for added durability.• A field-replaceable lifeline option is available most of the MSA SRL Models. In the event

that the webbing should become damaged, this option provides a field-replaceable web lifeline, eliminating costly returns to the manufacturer.

• A 400-pound working capacity as a standard feature.• No annual factory recertification required due to high-quality construction. This not only

reduces the cost of ownership, but also eliminates down time.• Some MSA SRL's offers an integral load indicator lets you know when it is time to remove

the product from service.• SRL connector with integral swivel.• Meets ANSI Z359.1-1992 (R1999), ANSI A10.32 and all applicable OSHA standards, and is

CSA certified.

Fall Protection

Part Number Description10120723 MSA Workman SRL, 9 m, stainless-steel cable

10119078 MSA Workman PFL EN, cable, 3.6 m, steel snaphoo, A-PFL-E-12G-0-6-N

10119082 Aptura SRL, 25 mm nylon web, 9 m, steel snaphook

25

Workman® TripodEasy to Use. Durable. Versatile. You asked for improved ease of use—the Workman Tripoddelivers! You asked for a minimum of two attachment points on the tripod head—the Work-man Tripod includes four attachment points!

Easy to UseThe Workman Tripod is very easy to use. A simple setup procedure makes the process quickand promotes correct use. Features that improve ease of use include:• Legs automatically lock in the open position for added safety.• A maximum height indicator provides quick and easy identification of the maximum leg extension length.

• There is no need for a separate pulley/bracket assembly, which makes hoist attachment easier and faster.

• Accessories can attach to any leg for faster set up.• Aluminiumleg and head design reduces weight, improving portability.• Telescoping legs (up to 8 ft. high) do not tangle when the unit is collapsed, for easier transportation and storage.

DurableA tripod needs to hold up well under use, and the Workman Tripod does. Built for durability,the unit features:• Skid-resistant feet with built-in leg base support strap that improves stability and strengthens the entire system.

• Cut-resistant pin retention chains that enable an extended service life.• An internal leg-locking mechanism prevents accidental disengagement during use and re

duces the possibility of damage to the mechanism during use or while in storage.

VersatileAnd as if ease-of-use and durability weren’t enough, the Workman Tripod offers great versa-tility:• The leg base support strap also serves as a convenient carrying strap.• Tripod legs feature 4-inch incremental adjustments with easy-to-insert ball detent pins.• The unit is “backwards compatible” with the MSA Lynx® Hoist and Lynx Rescuer, eliminat

ing the need to purchase new equipment or undergo costly upgrades.

Part Number Description10116521 MSA Workman Tripod

10016569 Side Mount Lynx Hoist with Emergency Drive and Air Drive Adapter,50' Galvanized Cable

506232 Bracket for Lynx Rescuer to mount to Tripod, 10M (30')/ 16M (50')

10011744 Lynx Rescuer Self Retracting Lanyard with Emergency Rescue 16M(50'), 3/16" diameter, stainless steel cable.

506473 Pulley/Bracket Assembly for Lynx Tripod

506222 Split Mount Pulley

Fall Protection

26

Thermal Imaging

For the Toughest Demands

MSA’s state-of-the-art Thermal Imaging Cameras (TIC) are invaluabletools for fire fighters and police, e.g. for fast and safe navigation insmoke filled rooms or dark environments.

All TIC models feature the same ergonomic design, robust componentsand extreme durability. The image quality is best-in-class. But the MSATIC models each feature different resolutions in order to ensure the opti-mal price-performance ratio for each application.

The practical modular system allows all four types of camera to be en-hanced with a Video Transmission System or a Video Capture. The VideoTransmission System gives the back-up team a clear view of what ishappening on the fire ground in real time. Furthermore a unique VideoCapture for documentation purposes is easily adaptable to all fourcameras.

27

Evolution® 5600 TICMSA Thermal Imaging Cameras are used by many of North America's largest fire departments. For big city performance with value-driven features, choose MSA's Evolution 5600 Thermal Imaging Camera with high resolution and detailed image quality. This versatile TIC provides detailed images (with a focal plane array of 120 x120, nominal 15,000 pixels) over a wide temperature range, in addition to safety andother exclusive offerings of MSA's Evolution Series cameras.

MSA's highly functional Heat Seeker and QuickTemp functions deliver unmatched performance and superior image quality at all temperatures, employing an easy-to-use, timetested design. User-friendly features and enhanced TIC performance help tomaintain low lifetime costs.

Most TICs trade image quality for a wider tem-perature range to keep the camera operating inhigh heat environments. However, the Evolu-tion 5600 TIC provides refined image qualityover comparable competitive TICs in Low Sensi-tivity mode. Only MSA thermal imaging cam-eras deliver High Sense image quality at up to3200 F, the temperature range that most oftenmatches that of structural fires.

For the Toughest Demands

High Sense image detail with Heat Seekerenhancing the heat source with red isotherm

Thermal Imaging

Part Num-ber Description

10085464 Evolution 5600 complete with Heat Seeker Plus, Standard Charger

10097334Evolution 5800 complete with User selectable palettes,2X Digital Zoom, Heat Seeker,Quick Temp and User’s (camera only)

Ask your MSA sales representative for more information.

28

Total Protection Whatever the Demands


Portable measuring instruments and personal monitors can begrouped into three application areas:

Combustible GasesThere are three elements required to ignite combustible gases:1. Fuel or flammable gas2. Heat or a source of ignition3. Oxygen to support combustion

This is known as the fire triangle. If you remove any one of the elements,combustion will not occur. The percentage of combustible gas in the airis also important.

According to the ATEX manufacturer directive 94/9/EC and the user di-rective 99/92/EC, any personal monitor for flammable gases, if used as asafety device to reduce the risk of explosion, has to be performance approved.

Any manufacturer seeking ATEX EC certification must demonstrate that their product conforms to EN 61779 (or EN 50054) as a minimumrequirement for gaining ATEX approval. All MSA combustible gas detectors are designed to comply fully with ATEX standards and cantherefore be used as safety devices.

OxygenInstruments to monitor oxygen deficiency or enrichment (measure-ment in vol.% range), to warn of the danger of asphyxiation or to moni-tor the inerting of tanks and containers.

Toxic GasesIn order to recognise and measure toxic substances in the ambient air(typically in ppm – parts per million), multi-gas instruments such as ALTAIR 5X are used.

29


Gas Detection You Can Rely On

ALTAIR® 5X Multigas Detector Features & BenefitsThe ALTAIR 5X Detector allows for an industry-first LEL,O2, CO, H2S, and SO2 60-second span calibration and10-second bump test time.

Features include:• The ALTAIR 5X Detector is equipped with an internal integral pump.• The ALTAIR 5X Detector is powered by the fast MSA XCell® Sensor family including the introduction of 3 new sensors.• 4-year expected sensor life on LEL, O2, CO, H2S, SO2, IR, and standard 3-year instrumentwarranty.• 3-year expected sensor life on NH3, Cl2, and standard 2-year warranty.• The ALTAIR 5X Detector provides an industry-exclusive end-of-sensor-life-warning.• MotionAlert™ feature - “man-down” alarm• InstantAlert™ feature - manual alarm•The ALTAIR 5X Detector is durable, providing industry - leading impact resistance.

Multigas Instruments


10116924 Altair 5X MONO DISPLAY with O2 (0-30%), CO, H2S, LEL 100%without 10 ft. S.Line & 1 ft. probe

10116926 Altair 5X MONO DISPLAY with O2 (0-30%), CO, H2S, LEL 100%with 10 ft. S.Line & 1 ft. probe

10116928 Altair 5X COLOUR DISPLAY with O2 (0-30%), CO, H2S, LEL 100%,with 10 ft. S.Line & 1 ft. probe)

10116929 Altair 5X COLOUR DISPLAY with O2 (0-30%), CO, H2S, LEL 100%,SO2 (0-20 ppm) with 10 ft. S.Line & 1 ft. probe

A-Alt5X-A-N-0-0-0-0 Altair 5X MONO DISPLAY with LEL 100% without S.Line & probe -ATO - A-Alt5XAN00000T00Q

A-ALT5X-A-N-K-0-0-0 Altair 5X MONO DISPLAY with LEL 100%, O2 (0-30%)withoutS.Line & probe ATO Matrix : A-Alt5XANK0000T00Q

A-Alt5X-A-N-K-B-1-0Altair 5X MONO DISPLAY with O2 (0-30%), CO, H2S, LEL 100%,CL2, without 10 ft. S.Line & 1 ft. probe ATO MATRIX: A-Alt5XANKB100T00Q

A-Alt5X-A-N-K-D-1-0Altair 5X MONO DISPLAY with O2 (0-30%), CO, H2S, LEL 100%,NH3, without 10 ft. S.Line & 1 ft. probe ATO Matrix : A-Alt5XANKD100T00Q

A-Alt5X-B-N-K-C-2-0Altair 5X with COLOR DISP, LEL 100% , O2(0-30%), NO2 (0-20ppm), CO sensor without 10 ft. S.Line & 1 ft. probe ATO MATRIX:A-Alt5XBNKC200T00Q

A-Alt5X-A-N-K-0-1-BAltair 5X MONO DISPLAY with O2 (0-30%), CO, H2S, LEL 100%,CO2 (IR) 0-10% Vol. w/o 10 ft. S.Line & 1 ATO MATRIX:A-Alt5XANK01B0T00Q

A-ALT5X-C-N-K-0-1-0ALTAIR 5X wireless with LEL METHANE O-100% LEL, O2 (0-30%),CO,H2S W/O Sampling Line & probe ATO Matrix :A-ALT5XCNK0100E00Q)

10042621 Sampling Probe Straight Airline 1ft. For Altair 5X

10040665 Sampling Line, Altair 5 10ft.

30

Protection for Man & Environment

ALTAIR 4X Multigas Detector with MSA XCell™ Sensor TechnologyMSA’s ALTAIR 4X Multigas Detector with new MSA XCell Sensor Technology offers many per-formance advantages: faster response time, four-year sensor life, increased stability, andless than 60-second calibration time. The ALTAIR 4X Multigas Detector operates with onlyMSA XCell Sensors for LEL, O2, two-toxic H2S/CO, or individual H2S and CO sensors.

The ALTAIR 4X Multigas Detector is compatible with the ALTAIR 4 QuickCheck® Station andthe ALTAIR 4 Galaxy® Test Stand (Galaxy System software upgrade is required), and providesexclusive optional MotionAlert™ and InstantAlert™ features.

Built on Durability • Full three-year warranty• Rugged housing• Withstands 20-foot drop• Easy to operate• Agency certified IP67 rating

Powered by Performance • Four-year sensor life, 60% longer than the industry average• MSA exclusive instrument end-of-sensor life warning• 24-hour run time, 71% longer than the industry average• Fast, high-performing sensors• MSA exclusive MotionAlert™ & InstantAlert™ Features• 50% less calibration gas used per minute than the industry average

Revolutionizing Sensor Technology • Sensor response and clear times under 15 seconds, 38% faster than the industry average• Span calibration time of 60 seconds• Typical cost savings of over 50% on calibration gas, replacement sensors and maintenance• Greater signal stability and repeatability under changing or extreme environmental

conditions• Two-tox CO/H2S sensor with virtually no cross-channel interference• The digital output of the sensors makes them much less susceptible to RF interference


10110704 ALTAIR 4X with LEL(0-100%), O2(0-30%), CO(0-1999ppm) andH2S(0-200ppm)

10110703 ALTAIR 4X with LEL(0-100%) and O2(0-30%)

10110701 ALTAIR 4X with CO(0-1999ppm) and O2(0-25%)

10110702 ALTAIR 4X with LEL (0-100%)

10047596 Universal Pump Probe (ATEX for Altair 4X)


31

Sirius® Multigas DetectorThe Sirius Multigas Detector provides users outstanding multifunctional capabilities byintegrating a high performance photoionization (PID) detector into a 4-gas detector.Users are able to simultaneously monitor for volatile organic compounds while meas-uring for combustible, toxic and oxygen-deficient atmospheres within one reliable,easy-to-use unit.

Features include:• MSA's innovative PID design (patent pending) provides users with superior PID performance including humidity resistance, stable zero readings and fast response times.

• Interchangeable rechargeable and disposable battery options can keep the instrument running practically 24 hours a day, 7 days-a-week.

Photoionization Detectors

ALTAIR Pro Single-Gas DetectorInnovative ALTAIR Pro toxic gas and oxygen detectors with replaceable sensor and batterydisplay gas concentration or percent oxygen on a large, clear, backlit LCD. The ALTAIR ProSingle-Gas Detector provides worry-free performance and stands up to the roughesthandling in even the toughest industrial environments. Its rubberized armor housing andone-button operation provide the durability and simplicity you expect from MSA.

Features include:• Ease-of-use (1-button operation).• Distinctive alarm system.• Alarm check, bump check, fresh air zero, and calibration made easy.• Easily replaceable, commercially available battery.• Replaceable sensors.• Built-in IR communication (event & data-logging).• Rugged design.• Water- and dust-resistant.

Single Gas Instruments

Part Number Description10074135 Altair Pro CO

10074136 Altair Pro H2S

10074137 Altair O2

10076716 Altair Pro Chlorine

10076730 Altair Pro Ammonia

10076736 Altair Pro SO2

Part Number DescriptionA-SIRIUS-A0100A01100010T0Q SIRIUS PID with O2 Sensor

A-SIRIUS-AL100A01100010T0Q SIRIUS PID with LEL and O2 Sensor

A-SIRIUS-AL111A01100010T0Q SIRIUS PID with LEL, O2, CO and H2S Sensor


32


ALTAIR Pro Remote Oxygen Detector (O2-R)The remote oxygen version for the ALTAIR Pro Single-Gas Detector is a unique design in thesafety industry. This O2 sensor is attached remotely at the end of a ten-foot cable, ratherthan inside the instrument’s casing. This design allows the user to lower the sensor into a re-mote location and monitor the O2 level from ten feet away.

Part Number Description10076733 Altair Pro O2 (Remote)

ALTAIR Single-Gas DetectorThe ALTAIR Single-Gas Detector featuring sensor options for carbon monoxide, hydrogensulfide and oxygen will operate for over two years. This long lifespan, coupled with theunit’s high performance, results in one of the most cost-effective monitors on the market.Advanced design offers superior dust and water protection and high resistance to RFI. Thetriple-alarm system featuring two bright LEDs, a piercing audible alarm, and a vibratingalarm ensures that no alarm condition goes unnoticed.

Features include:• Factory-calibrated detector with warranted two-year service life (1080 alarm minutes)• Maintenance-free; no sensor or battery changes necessary• Bump check confirmed with checkmark on instrument LCD, displayed for 24 hours• Event recorder stores 25 latest events automatically in instrument memory• Built-in IR communications enables interface FiveStar® Link® Software• Built-in gas delivery adapter for gas response tests (No cal cap to lose)• Rated to IP67 for dust and water ingress

Part Number Description10092521 ALTAIR Single Gas H2S

10092522 ALTAIR Single Gas CO

10092523 ALTAIR Single Gas O2

33


Calibration Accessories Regulators & Tubes

Part Number Description467895 Fixed Flow Regulator, 0.25 LPM, Model RP

710288 Demand Regulator

10030325 Tubing, 40 cm (16") (not used for NH3, Cl2 or ClO2)

10080534 Tubing, 40 cm (16"), Tygon (NH3, Cl2, ClO2 only)

ALTAIR 4X Multigas Detector Parts List

Part Number Description10040002 Clip, Suspender Style, black

711302 Sensor, CO

711303 Sensor, H2S

10046946 Sensor, O2 (Oxygen)

10080220 Sensor, HCN (Hydrogen Cyanide)

10080221 Sensor, Cl2 (Chlorine)

10080223 Sensor, SO2 (Sulfur Dioxide)

10080224 Sensor, NO2 (Nitrogen Dioxide)

10080225 Sensor, NH3 (Ammonia)

10016798 Sensor, O2 - Remote Version

10080222 Sensor, ClO2 (Chlorine Dioxide)

10071375 Sensor Gasket

10067102 Horn Gasket

10074132 Battery - CR2636267 Screws, Case


10069894 SS Suspender Clip

10047596 Universal Pump Probe (ATEX)

10089321 Calibration assembly (cap, tube, connector)

10086638 European Power Supply

10088099 MSA Link Software CD-ROM

10082834 JetEye IR adapter with USB connector

10106722 XCell Ex Combustible sensor

10106729 XCell O2 sensor

10106725 XCell CO/H2S duo-tox sensor

10110030 Front Housing with integrated dust filters(Charcoal)

10110029 Front Housing with integrated dust filters(Phosphorescent)

10045035 58L Quad gas Mix Cl, 45 % CH4, 15% O2, 60 ppm CO, 20 ppm H2S

10110061 LCD frame assembly (frame, LCD, zebra strips, screws)

10106621 Main board with battery pack

10111202 Charger, 5 units, ALTAIR 4X, EN Plug

10111204 Charger, 10 units, ALTAIR 4X, EN Plug

ALTAIR® Pro Single-Gas Detector Parts List

Replacement Parts & Accessories


34


Monitoring of hazardous gases and vapours in plants and large areas isnecessary in all branches of industry. Directives and regulations coveringthe protection of plant and personnel as well as the monitoring of im-missions require suitable gas detection equipment. In addition toportable instruments for personnel monitoring, permanently installeddetection systems (detectors and controllers) are used for continuousmonitoring.

MSA is one of the few suppliers of permanent gas detection technologythat develops and manufactures a complete range of sensors, con-trollers and monitors and integrates them into system solutions. This isthe way to develop optimum systems that can meet all customer re-quirements at an excellent performance-price ratio - an unbeatable casefor safety and flexibility.

Whether stand-alone, or integrated into existing control and monitor-ing systems, MSA offers made-to-measure solutions.

MSA's portfolio on Permanent Gas and Flame Detection Systems includes:• Controllers• Detectors• Sensors• Monitors• Fire and Gas Detection Systems

Alongside the extensive range of the products mentioned above, MSAalso provides a high level of customised service including: project plan-ning and development, installation support and commissioning, main-tenance and system modification.

Complete Safety Solutions

35

State-of-the-Art Detection Technology

47K SeriesCost effective passive catalytic sensors to detect potentially hazardous concentrations offlammable gas and vapour in air up to 100% LEL.Available as Standard (ST), Poison Resistant (PRP), High Temperature (HT) versions with acomplete range of accessories and junction boxes to meet virtually all industrial applica-tions. Series 47K sensors used in combination with MSA Controllers fully meet the require-ments of ATEX Directive 94/9/EC, including performance approval, and being SIL 2 capablethey can be used as part of a safety related system.For more information, please see leaflet 07-240.2.ATEX II 2G Ex d IIC T3/T4/T6, II 2D Ex tD A21 IP6X T85°C/T135°C/T200°Cincluding performance approval, SIL 2

36


Prima XIThe PrimaX I gas transmitter detects a wide range of toxic gases and oxygen using anelectrochemical sensor technology.Innovative enclosure design, ease of use, fast installation and being suitable for both indoorand outdoor installations make the PrimaX I transmitter your choice for versatile gas detec-tion. The large display with clear plain text provides information at a glance. Calibration iseasily performed using the built-in keypad or via HART digital protocol. The plug-in replace-ment sensors and an integral backplate enable fast and easy installation.PrimaX I comes as general purpose or intrinsically safe design in a robust anti-static, rein-forced nylon housing with standard 4–20 mA output and optional HART capability. SIL 2compliance is approved by TUV. For more information, please see leaflet 07-710.2.ATEX II 1G Ex ia IIC T4 Ga, II 2D Ex ia IIIC T130 °C Db IP54, SIL 2

Prima XPThe PrimaX P gas transmitter is suited to a wide range of indoor and outdoor applicationsfor the detection of combustible gases (catalytic combustion sensor), toxic gases or oxygen(electrochemical sensors).The PrimaX P features an innovative custom designed enclosure with integral 4-way keypadfor ease of use. The large LCD with clear plain text provides information at a glance and theadditional LEDs give a clear status indication. The plug-in replacement sensors and an inte-gral backplate enable fast and easy installation.PrimaX P comes as flameproof design in a coated aluminium enclosure with standard 4–20mA output and optional HART and relays capability. SIL 2 compliance is approved by TUV.For more information, please see leaflet 07-710.2.ATEX II 2G Ex d ia [ia] IIC T4 Ga, II 2D Ex tb ia [ia] IIIC T130 °C Db IP67, SIL 2

Prima XIRThe PrimaX IR offers hydrocarbon detection in LEL range using infrared absorptiontechnology through the patent-pending PrimaX IR dual source design. A redun-dantIR source provides reliability and uninterrupted monitoring should a source failureoccur. The 316 stainless steel, IP67-rated, rugged housing protects the PrimaX IRfrom environmental extremes. Standard 4–20 mA output with HART capability of-fers user-friendly set-up, calibration diagnostics, and maintenance. A unique envi-ronmental guard with patent-pending clamshell design provides convenientinstallation in tight locations.For more information, please see leaflet 07-715.2.ATEX II 2G Ex d IIC T4 Gb, II 2D Ex tb IIIC T130°C Db IP67, SIL 2

37

ULTIMA® MOS-5 and ULTIMA® MOS-5EULTIMA MOS-5 and MOS-5E detect ppm levels of hydrogen sulphide (H2S),providing status indication and alarm outputs. Their performance is based on theirmetal oxide semiconductor sensor with unique technical parameters. High tolerancefor a broad range of temperatures, humidity levels, as well as short-term high H2Sconcentrations and very low cross sensitivity to common gases make thesedetectors ideal for installation in harsh environments.The ULTIMA MOS-5 provides analogue 4–20 mA and 3 relay outputs in a stainlesssteel housing. The ULTIMA MOS-5E incorporates analogue 4–20 mA and three opencollector outputs in an aluminum housing. HART and Modbus communicationenable complete status and control capability in the control room.For more information, please see leaflets 07-481.2 and 07-482.2.ATEX II 2GD EEx d IIB+H2 T5, SIL 2 and SIL 3, IP66,HART registered (ULTIMA MOS-5) ATEX II 2G EEx d e m IIC T4, SIL 3, IP66/67 (ULTIMA MOS-5E)

ULTIMA® XL/XT SeriesThe cost-effective fixed installation gas monitors ULTIMA XL and XT with HART fieldcommunications protocol use well proven catalytic, electrochemical and infraredtechnologies for detection of combustible and toxic gases and for oxygen deficiency.The interchangeable smart sensors can be changed under power without declassifyinga hazardous area. With the non-display ULTIMA XL/XT gas monitors the user has multiplecalibration options: the handheld HART communicator, a controller or laptop which com-municates via a dedicated HART Software and local internal LEDs and push-buttons.ULTIMA XL is explosion-proof with a stainless steel enclosure, while ULTIMA XT uses ageneral purpose, water and corrosion resistant polycarbonate housing.For more information, please see leaflet 07-704.2. ATEX II 2 (2) G Ex d (ib) IIC T6, II 3 (2) G ExnA (ib) IIC T6, IP66 (ULTIMA XL)

ULTIMA® X SeriesThe ULTIMA XE and XIR provide continuous monitoring of combustible and toxic gasesand oxygen deficiency using catalytic, electrochemical and infrared sensor technologies.They are suitable for almost all applications in virtually any type of industry.A large easy to read LCD shows the gas reading and gas type as well as clear text statusmessages. The ULTIMA X series is powered from 24 VDC with a 4–20 mA output signaland optional on board status LED’s and/or output relays. Smart sensor technology allowssensor disconnect and replacement under power in hazardous locations.ULTIMA XE gas monitors are also available with HART field communications protocol.The ULTIMA XA comes in a rugged plastic general purpose enclosure. It is available with4–20 mA analogue output or with optional HART protocol.For more information, please see leaflets 07-703.2 and 07-705.2.ATEX II 2G EEx d IIC T4, including performance approval,SIL 2 (ULTIMA XE)ATEX II 2G EEx d IIC T5/T6, including performance approval


38


FlameGard 5 SeriesDesigned with advanced ultraviolet (UV) and infrared (IR) sensing technology, theFlameGard 5 Series represents the state-of-the-art in secure flame monitoring.The FlameGard 5 MSIR, a multi-spectral infrared detector designed to detect hydrocarbonfires, features breakthrough Neural Network Technology (NNT) for reliable discriminationbetween actual flames and nuisance false alarm sources within a distance of up to 70 m.FlameGard 5 UV/IR is designed to detect hydrocarbon fires within 15 m, FlameGard 5UV/IR-H2 is optimized to detect hydrogen based flames, and FlameGard 5 UV/IR-E withstainless steel housing and Ex e wiring compartment enables high level of resistance inharsh environments. The FlameGard 5 Series flame detectors provide standard 4–20 mAoutput with optional relays or HART and Modbus digital communication. Suitable for a widerange of applications in the production, transport and processing.For more information, please see leaflets 07-471.2, 07-472.2, 07-473.2 and 07-475.2.ATEX II 2G Ex d IIC T5 Gb, II 2D Ex tb IIIC T100 °C Db, SIL 3, HART registered (MSIR, UV/IR)ATEX II 2G Ex d e IIC T4/T5 Gb, II 2D Ex tb IIIC T135 °C /100 °C Db, IP6X (UV/IR-E)

ULTIMA® OPIR-5The ULTIMA OPIR-5 open path hydrocarbon gas transmitter provides continuous monitor-ing of methane and propane gas concentrations based on advanced infrared sensor tech-nology features. The dual detection range enables sensitivity to both small (ppm•m) andlarge (LEL•m) gas leaks.The ULTIMA OPIR-5 includes continuous self-check monitoring for fail to safe operation.Automatic gain control compensates for dirty optics, rain, and fog. The result is precision ac-curacy with exceptional reliability in harsh environments and improved false alarm rejectionwith an optical path length of up to 150 m.Standard analogue output 4–20 mA with HART capability, relays and RS485 Modbus allowto connect ULTIMA OPIR-5 to standard industrial controllers.For more information, please see leaflet 07-483.2.ATEX II 2G D Ex d IIB+H2 T4 Gb, II 2D Ex tb IIIC T135 °C Db IP66/67

UltraSonic IS-5 and UltraSonic EX-5The UltraSonic IS-5 and EX-5 are non-concentration based gas detectors used to detectleaks from high-pressure systems with a maximum coverage radius of 20 meters. They re-spond to the airborne ultrasound generated from gas releases in open ventilated areas,where traditionalmethods of detection may be difficult.The intrinsically safe UltraSonic IS-5 is suited for installations restricted to low power (< 1W). The explosion-proof UltraSonic EX-5 features the Senssonic™ patented self-test for fullfailsafe operation and a three digit LED display showing actual ultrasonic level value (in dB)and alarm indication. Standard 4–20 mA output with HART capability and output relays cancontrol additional action in case of alarm or fault condition.For more information, please see leaflets 07-491.2 and 07-492.2.ATEX II 2G EEx ia IIC T4, SIL 1 and SIL 2 (UltraSonic IS-5)ATEX II 2G EEx d e ib IIB+H2 T6, SIL 2 and SIL 3 (UltraSonic EX-5)

39

9010/9020 LCD and 9020-4 LCDThe control system 9010/9020 LCD provides maximum flexibility, simple operation, highreliability and superb performance at considerably reduced costs. In combination with thelarge range of MSA gas sensors, the 9010/9020 LCD excels in a variety of industrial applica-tions, there could be a presence of dangerous gas concentrations.The 9010 LCD control module processes signals from one gas sensor while the 9020 LCDprocesses signals from two independent gas sensors. The system is also available as a singleor dual channel wall mount and in ABS hous ings or as 19” rack version with up to5 or 10 modules.The 9020-4 LCD is identical to the 9020 but is configured as a four-channel IP65 controller tosuit marine and industrial applications.For more information, please see leaflets 07-516.2 and 07-517.2.ATEX II (1)G (2)G, MED 96/98/EC

Controllers

GasGard XLThe GasGard XL is a multi-channel wall mount controller for monitoring toxic, oxygen andflammable gases in industrial plants. It can be easily configured to accept up to eight re-mote gas sensors, depending on the number of individual plug-in input cards installed. Thelarge, easy-to-read, multi-language LCD graphic display allocates real time information ontarget gas levels and events, allowing full system diagnosis, supported by individual LEDsper channel, relays and internal buzzer. For more information, please see leaflet 07-515.2.ATEX II (1)G (2)G, SIL 2, MED 96/98/EC

SUPREMATouchSUPREMATouch is a gas and fire warning system for large area measuring and monitoringin industries and small or medium size plants. It can be used with a wide range ofdetectors including flammable and toxic gas, oxygen, smoke, fire and heat and manualcall points.The SUPREMATouch includes a large colour touchscreen display for easier and userfriendlyoperation, enhanced processing power and addressable fire and detectorcapability. Latest hardware and software technology permits simple planning,installation, configuration, integration and operation.The compact, modular design of the SUPREMATouch allows it to be economically tailoredfor each application and be extended and adapted any time to meet changing sensorand alarm requirements.Designed around standard industrial 19” racks, SUPREMATouch provides signal processingfor up to 256 inputs and 512 outputs and the ability to distribute the system over up to8 racks using satellites to minimise installation cost.For more information, please see leaflet 07-500.2.ATEX II (1)G (2)G, SIL 3, MED 96/98/EC


40


CHILLGARD RTThe CHILLGARD RT is a single or multipoint gas warning system suitable for all industrial re-frigeration systems or chillers be it production or research operations, food cold storage ormeat packing operations. It allows precise monitoring of the smallest refrigerant concentra-tions and detection of leak locations.The instrument works for months with very little deviation from the zero point. Due to itsexcellent detector stability, unlike other products, the zero point adjustment can be re-duced to once a year. The CHILLGARD RT generates the signals required to initiate audibleand visible alarms. For more information, please see leaflet 07-523.2.

CHILLGARD M-100The CHILLGARD M-100 refrigerant sensor is designed to detect the presence of the mostcommon halogenated refrigerants in cold storage facilities, mechanical equipment roomsand other refrigerant applications. This compact sensor can be mounted almost anywhereto detect potential leaks of halogenated refrigerants. Easy installation ensures fast and prac-tical integration into existing automated systems. For more information, please see leaflet07-526.2.

Monitors

CHEMGARDThe CHEMGARD gas monitor can monitor more than 60 gases in the TLV range, such ashydrocarbons, solvents, alcohols, alkanes and toxics.The photoacoustic infrared sensing technology provides precise, low cost and high per-formancemonitoring. It is extremely stable and highly selective to the gas of interest and can operateformonths with virtually no zero drift.An optional multi point sequencer can be included in the CHEMGARD to allow either 4 or8 points to be sampled. The monitor provides 3 freely adjustable alarm levels and relay out-puts foreach alarm level.For more information, please see leaflet 07-524.2.

41

My Notes

MSA - The Safety Company

MSA - The Safety CompanyWorldwide Locations

Central Region Home Office -IndorePiyush BosePhone: +91-9893655522Email: [email protected]@msasafety.com

Southern Region - Hyderabad/Bangalore

Ashok GopuPhone: +91 – 9393323939Email: [email protected]@msasafety.com [email protected]

www.MSAsafety.com

India Offices

With MSA’s worldwide presence we deliver the right safety solution tothe right place, at the right time, supported by highly skilled personnelat local MSA offices.

Nearly 5,000 MSA staff are at work throughout the world to ensure thatyou always get the best safety solution.

We are always ready to assist you in choosing the right option and tohelp you purchase the right equipment. Whatever information andadvice you require on our products and services, we are always therefor you.

Simply contact MSA India for assistance.

Northern Region Home office - Delhi / LucknowKrishan SrivastavaPhone : +91-9990255764/ +9711196516Email: [email protected]@[email protected]

Western Region Home Office -VadodraChintan L. BhattPhone: +91 - 9624777669Email: [email protected]@msasafety.com

42

Central Logistics Hub Mumbai2nd Floor, KMK House, Plot No. - 52, PanvelIndustrial Co-Operative Estate LtdPanvel, Navi Mumbai - 410206Maharashtra, IndiaOffice Phone : +91 22 65295486 / 2Email: [email protected]@msasafety.com

MSA (INDIA) LimitedEcostationLevel-16 (Floor) Plot No.7, Block BP,Salt Lake, Sector V,Kolkata 700091 IPhone : +91 33 2367 2260 to 64Fax : +91 33 2367 2265Email : [email protected]

Southern Region - Chennai1st Floor, Alsa TowerPlot # 186-187, KilpaukPoonamallee High RoadChennai - 600 010Phone: +91-44-2532-5185Fax: +91-44-2665-0342Email: [email protected]@msasafety.com

For Sales enquiry : [email protected] Service Enquiry: [email protected]

Documents

Air Purifying Respirators page 8 Head, Eye & Face Protection page …fairpowerage.com/upload_file/catelogue_pdf/147_small_MSA... · 2019-01-28 · Portable Instruments page 29 Fixed