ADA/ANSI COMPLIANT BARRIER-FREE SHOWER STALLS .ada/ansi compliant barrier-free shower stalls For

  • View
    214

  • Download
    0

Embed Size (px)

Text of ADA/ANSI COMPLIANT BARRIER-FREE SHOWER STALLS .ada/ansi compliant barrier-free shower stalls For

  • 1 Aquatic 8101 E. Kaiser Blvd. Anaheim, CA 92808 (800) 877-2005 FAX (714) 998-5340 www.aquaticbath.com

    InstallationDataAccessible Showers with Pre-leveled Base

    Fax on Demand # 2907

    Items Included

    Shower

    Tools Needed

    ADA/ANSI COMPLIANT BARRIER-FREE SHOWER STALLSFor roll-in showers with a flat threshold, build up or recess the bathroom floor 3/4 less the thickness of the finished floor. For beveled thresholds, build up or recess the bathroom floor 3/4 less the thickness of the finished floor, ensuring that the finished floor meets the base of the bevel at the threshold.

    It is recommended that the bathroom floor outside ADA clear floor space be designed with a floor drain to alleviate any water over spray that may escape the shower stall.

    3/16Drill Bit

    3-1/2Drill Bit

    1Drill Bit

    Phillips Screw Bit#8 X 1 Pan Head Screws

    100% Mildew ResistantSilicone Sealant

    1/4 x 3/8 SquareNotched Trowel

    Product illustration may not be representative of your unit.

    3/16 Drill Bit

    3-1/2 Drill Bit

    1 Drill Bit

    Phillips Screw Bit

    #8 X 1 Pan Head Screws

    100% Mildew Resistant Silicone Sealant

    Square Notched Trowel(For use on non-level floor applications only.)

    Level

    Hammer

    Tape Measure

    Drill

    Aquatic products may be specified as Lasco Bathware.

  • 2 Aquatic 8101 E. Kaiser Blvd. Anaheim, CA 92808 (800) 877-2005 FAX (714) 998-5340 www.aquaticbath.com

    InstallationDataAccessible Showers with Pre-leveled Base

    Fax on Demand # 2907

    NOTICE: Please inspect the unit thoroughly before installation to make sure it has not been damaged during transportation. Under no circumstances should a damaged unit be installed. Neither Aquatic nor the distributor will be responsible for removal or reinstallation costs should a replacement be necessary due to installation of a damaged unit.

    PRE-INSTALLATION PLANNING

    1. Unitmustbeplacedwithinbathroomareabeforecompletionofdoorframingor,ifpreferred,studsmaybeomittedorknocked-outtopermitunitplacement.

    2. ReviewjobprintandAquaticrough-indimensions;verifyallkeydimensionsagainstactualjobconditions.

    3. Makesureframed-inalcoveisofpropersize,squareandplumb;checkfloorforlevelness.

    4. If alcove floor is not completely level, foundationmaterials[industrialplaster,mortarmix]aremandatoryunderthebottomofeachunittosolidifyforwheelchairsupport.

    5. Iffire-ratedalcoveisrequired,approvedfinishmaterialmustbeinplacepriortounitinstallationtomeetfiresafetyrequirementsoflocalbuildingcodeand/orFHA/HUDMinimumPropertyStandards.NOTE: Finished alcove must have interior dimensions shown on rough-in diagram to permit installation of unit.

    6. Provide6(150mm)flooropeningfor2(50mm)IPSanddrainconnection.

    7. Toavoidobstruction,makesurethatsupplylinesandvalveplumbingarenotstrappedtostudsanddonotprojectintoalcove.Also,drainpipemustnotprojectabovefloorlevelpriortoinstallation.

    8. Makesureallplumbingiscompleteandtocode.

    9. Topreventscuffingwhileinstallingunit,covertheentirebottomoftheunitwithapieceofcardboardorotherprotectivematerial.

    10.Fasten drain fitting to unit before installing[seemanufacturersinstructions].Fastenersforwoodframing112galvanizedroofingnailsor#10x112self-tappingwasherheadscrews;forconcreteorblockwalls1concretenailsandnailingtool;forsteelstuds(18ga.)drillflangesandstudswith532carbidebitanduse#12x1sheetmetalscrews.

    INSTALLATION PROCEDURE

    For non-level alcove floor applications, prepare a foundation material mix (industrial plaster, mortar mix) and spread throughout the alcove floor with a square notched tile trowel. The foundation materials should spread around the drain and extend to the perimeter of the shower floor.

    6Dia.

    Rough In

    Rough CenterOverall Width

    OverallDepth

    1

    Foundation Material

    Square Notched Trowel

    2

    Note: If fire-rated alcove is required, approved finish materials must be in place prior to unit installation to meet fire safety requirements of local building codes and/or FHA/HUD Minimum Property Standards.

    Check dimension of alcove; make sure walls are square and plumb and floor is level. For completely level floor, proceed to Step 3.

  • Aquatic 8101 E. Kaiser Blvd. Anaheim, CA 92808 (800) 877-2005 FAX (714) 998-5340 www.aquaticbath.com 3

    Aquatic 8101 E. Kaiser Blvd. Anaheim, CA 92808 (800) 877-2005 FAX (714) 998-5340 www.aquaticbath.com

    InstallationDataAccessible Showers with Pre-leveled Base

    Fax on Demand # 2907

    3 4

    5

    Mark fitting locations. (Refer to measurements from step 3.) Using a hole saw (fine tooth or abrasive grit cutting edge), make necessary openings for filler and valves, drilling from inside (smooth side) out.

    If mounting fittings from stable reference points (back wall studs, floor) measure the locations of spout and valves. Note measurements.

    INSTALLATION PROCEDURE, CONT.

    Check for level.

    6

    7 8

    Fasten panel to framing at every stud and eight inches vertically through nailing flange..

    Cover the entire bottom of the unit with a piece of cardboard or other protective material. Pre-drill pilot holes.

    Place the unit directly on level floor (or on top of foundation materials) with drain fitting over and onto waste pipe with threshold firmly on the floor. Assure waste pipe protrudes well into drain fitting. Maintain proper floor slope towards drain.

  • 4 Aquatic 8101 E. Kaiser Blvd. Anaheim, CA 92808 (800) 877-2005 FAX (714) 998-5340 www.aquaticbath.com

    InstallationDataAccessible Showers with Pre-leveled Base

    Fax on Demand # 2907

    CLEAN-UP

    1. Do not remove warranty/maintenance adhered label.Leaveonunitforowner/occupantpercoderequirement.

    2. Prevent staining.Removealldebrisbeforeplumbingleaktest.Usespongewithwarmwaterandliquiddetergent.Rinse,drainandwipeclean.Donotuseabrasivecleanserssuchasscouringpowders,steelwool,metalscrapers,sandpaperoranythingelsethatmightmar,dullorscratchthefinish.

    3. Plasterandlaxespaintmayberemovedwithwarmwater,liquiddetergentandbrittlebrushorplasticscraper.Glues,tarsandenamelsmayberemovedwithacetoneorpaintthinner.Do not useturpentineorlaquerthinner.Do not useexcessiveheatoranycausticsolventsorchemicals.

    4. Dullareasandlightscratchesmayberemovedbybuffingwithalightcoloredautomotiverubbingcompoundandbuffingpad.Entireunitcanbewaxedwithlightcoloredautomotivewax.Do not wax bottom of unit.

    5. Seeusermaintenancelabelformoredetails.

    USER MAINTENANCE INSTRUCTIONS

    IMPORTANT! Use only recommended cleaners and procedures described herein. Use of other materials and methods may damageyour bath fixture and void the warranty.

    1. Fornormalcleaning:Neveruseabrasivecleanerssuchasscouringpowdersorpads,steelwool,scrapers,sandpaperoranythingelsethatcouldscratchordullthesurfaceofyourAquaticunit.Instead,usewarmwaterandliquiddetergentsornon-abrasivecleansers,especiallythosebathroomcleanersrecommendedforcleaningfiberglass.

    2. TokeepyourAquaticbathfixturesparklingclean:Applyacoatofgoodqualityautomotivepastewaxorpolishandbufftoahighshinewithasoftclothortowel.Repeateverysixmonthsforeasiercleaningandlonglastingprotection.

    NOTE:DONOTWAXtextured,slip-resistantstandingsurfaceoftheunitbottom.Thiscouldresultingreaterriskofslippingandpersonalinjury.

    3. Torestoreascratchedordullunit:Useanautomotivepolishingcompoundappliedwithacleancottonrag.Rubscratchesanddullareasvigorously.Wipeoffresidues.Followwithautomotivewaxtreatmentdescribedabove.

    4. Toremoveadhesive:Try3-MNaturalCleaner,De-Solv-Itorsimilarmaterials.Ifresiduesremain,saturateasmall,white,cottonragwithnailpolishremover(naphthaoracetone)andrubvigorouslyuntiltheadhesivedissolvesanddisappears.Thesesolventsarehighlyflammableandmustbeusedsparinglyandwithcaution.Donotsmokeorpermitotherstodoso.Makesureallnearbyheatingdevices(includingpilotlights)areextinguished.Donotallowsolventtogodownthedrain.Makesurenottocontactplasticdraingratesorothersyntheticmaterials.

    5. RubberMats:Ifyouusearubberanti-skidmat,makesuretoremoveitfromtheunitaftereachusetoavoidharmtothesurfacefinish.

    6. HardWater:Waterincertainregions,ifnotwipedupafterbathing/showering,maycausefadingofsomebathfixturecolors.ThisisanaturaloccurrencebeyondAquaticscontrol.(SeeWarranty)

    CAUTION: When using any cleaning or polishing materials, make sure to read and follow all package instructions carefully. Wear rubber gloves at all times and avoid contact with eyes, skin, clothing, rugs and furnishings. Make sure all residues are rinsed off thoroughly.

    1521 No. Cooper, Ste. 500Arlington, TX 76011PH: 800-945-2726, 817-801-8300FAX: 866-544-5353

    Customer Service | Technical Services | Warranty Services

    LITID2907

  • Aquatic 8101 E. Kaiser Blvd. Anaheim, CA 92808 (800) 877-2005 FAX (714) 998-5340 www.aquaticbath.com 5

    Aquatic 8101 E. Kaiser Blvd. Anaheim, CA 92808 (800) 877-2005 FAX (714) 998-5340 www.aquaticbath.com

    Elementos incluidos

    Regadera

    Herramientas necesarias

    Informacin de instalacinRegaderas accesibles con base nivelada

    Fax informativo a pedido # 2907

    CABINA DE REGADERA SIN OBSTCULOS CONFORME A ANSI Y ADA (LEY PARA ESTADOUNIDENSES CON DISCAPACIDAD)

    Para regaderas adaptadas para silla de ruedas con borde plano, eleve el piso del bao o haga un receso en piso del bao de manera que quede 3/4 (1.9 cm) ms bajo que el grosor del piso terminado. Para bordes biselados, eleve el piso del bao o realice un receso en el piso del bao de manera que quede 3/4 (1.9 cm) ms bajo que el grosor del piso ter