Access Control( Hardware )

June 25, 2010

Created by Castaly / Andy Chen

Access Control

• Guideline

• Introduction

• GV-Reader Series

• GV-Controller Series

• Accessories

• Advance Section

• Summary

• FAQ

• Guideline for Access Control

AS-HAS-H

Access Control

IntroductionIntroduction

• What is access control?

– Access Control is any mechanism by which a system grants or revokes the right to access some data, or perform some action. Normally, a user must first login to a system, using some Authentication system. Next, the Access Control mechanism controls what operations the user may or may not make by comparing the UserID to an Access Control database.

Introduction

• In order to install an Access Control System, you will need the hardware items below.– GV-Controller– GV-Readers / GV-GF

Fingerprint Reader

Introduction

AS-H01AS-H01

Access Control

System StructureSystem Structure

• System Structure for Access Control

AS-H02AS-H02

Access Control

GV-Reader SeriesGV-Reader Series

What’s Reader?

• Data Reader

• A input device

• A combination of readers or tags

• GV-Reader Series Products– GV-Reader 1251– GV-Reader 1352 V2– GV-GF1900– GV-GF1901– GV-GF1902– GV-AS100

What’s Reader?

• GV-Reader 1251– Support Wiegand 26 / RS485

Interface– Frequency: 125KHz– Type of Card: E– Card / Tag distance: 4 cm / 3 cm– Temperature: -20 ~ 65 C

What’s Reader?

• GV-Reader 1352V2– Support Wiegand 26 / RS485

Interface– Frequency: 13.56MHz– Type of Card: M / F– Card / Tag distance: 5 cm / 4 cm– Temperature: -20 ~ 65 C

What’s Reader?

GV-Reader 1251

GV-Reader 1352V2

CommunicationWiegand 26 /

RS-485Wiegand 26 /

RS-485

Frequency 125 KHz 13.56 MHz

Card / Tag Type E M / F

Distance between

Card & Reader4 / 3 (cm) 5 / 4 (cm)

Temperature-20 ~ 65°C /

-4 ~ 149°F

-20 ~ 65°C /

-4 ~ 149°F

What’s Reader?

• GV-GF Enrolled Installation

What’s Reader?

• GV-GF1900–Wigand 26 – Frequency: 13.56MHz– Type of GV-Card: F– Temperature: 0 ~ 65 C – Sensing Area: 12 mm x 16 mm– Sensor: Capacitive– No output– Operate Mode: Card + Finger

What’s Reader?

• GV-GF1901–Wigand 26 / RS485– Frequency: 13.56MHz– Type of GV-Card: F– Temperature: 0 ~ 65 C – Sensing Area: 13.2 mm x 18.5

mm– Sensor: Capacitive– Support 1 output ( 240V,

2.5A )– 1900 Fingerprints– Operate Mode: Card + Finger

or Finger Only mode

What’s Reader?

• GV-GF1902–Wigand 26 / RS485– Frequency: 13.56MHz– Type of GV-Card: F– Temperature: 0 ~ 65 C – Sensing Area: 17 mm x 20 mm– Sensor: Optical– Support 1 output ( 240V,

2.5A )– 1900 Fingerprints– Operate Mode: Card + Finger

or Finger Only mode

What’s Reader?

What’s Reader?

GV-GF1900 GV-GF1901 GV-GF1902

產品差異

Communication Wiegand 26Wiegand 26

RS-485

Wiegand 26

RS-485

Frequency 13.56 MHz 13.56 MHz 13.56 MHz

Card / Tag Type F F F

Temperature0 ~ 65°C / 32 ~

149°F0 ~ 65°C / 32 ~ 149°F 0 ~ 65°C / 32 ~ 149°F

Finger 感應介面 電容式 電容式 光學式

Finger 感應面積 12x16(mm) 12x16(mm) 17x20(mm)

I / O 介面 None 1 Port (240V/2.5A) 1 Port (240V/2.5A)

Support Mode Card + Finger ModeFinger only Mode

Card + Finger Mode

Finger only Mode

Card + Finger Mode

優點 1. 感應速度快 2. 不受光線干擾

1. 感應速度快 2. 不受光線干擾

1. 指紋偵測面積較大2. 無手汗症 & 乾手症感應不良的狀況

缺點

1. 對於手汗症 & 乾手症感應較差2. 無 RS-485 介面3. 無 output 輸出

1. 對於手汗症 & 乾手症感應較差

1. 光線干擾問題2. 感應速度較慢

AS-H03AS-H03

Access Control

GV-Controller SeriesGV-Controller Series

Access Control

• GV-AS200 Controller

• GV-AS400 Controller

• GV-AS100 Controller

• GV-ASBox

• GV-AS200 Controller

GV-AS200

• GV-AS200 Controller– Two to four doors controller– Support 4 Wiegand card reader

26~40 bits– Support up to 8 card readers via

RS485– 4 Inputs / 3 outputs for each door • Inputs: Sensor, Button, Fire, Tamper• Outputs: Alarm, Door, Urgent

GV-AS200

• GV-AS200 Controller–What if there is a

disconnection between GV-AS200 controller and GV-ASManager, can GV-AS200 controller still be operated?• 65536 event buffer• 10000 access card information

–What happens to GV-AS200 controller if connection is back?

GV-AS200

• GV-AS200 Controller– Not support GV-GFV1901, GV-

GFV1902 RS485 interface– GV-GF can ONLY use Wiegand

interface– Connect to ASManager via RS485

or TCP/IP• RS485 must connect to GV-Hub, GV-Com or GV-Net I/O card v3.1

– Connect Card Reader to AS200 Controller via Wiegand or RS485

GV-AS200

• GV-AS400 Controller

GV-AS400

• GV-AS400 Controller– A four doors controller– Support 8 Wiegand card reader

26~64 bits– Support up to 8 GV-Readers /

GV-GF via RS485– 16 Inputs / 16 outputs • Max voltage / current difference

between 1~8 outputs and 9~16 outputs

GV-AS400

• GV-AS400 Controller– Connect up to 4 GV-I/O box• GV-IOBox 4,8,16• Max 80 inputs / 80 outputs

– GV-Reader / GV-GF can connect up to 8 via RS485 connection• Only compatible with

GeoFinger1901/1902

– Not support Security mode

GV-AS400

• GV-AS400 Controller–What does it mean when ” low

battery” error message shows up in GV-ASKeypad?• AS400 remains 10 hours after the

battery stops working.

GV-AS400

• GV-AS100

GV-AS100

• GV-AS100– One door controller– Support 1 Wiegand interface

( 26~64 bits )– 65536 event buffer – Support 1000 Card information– 3 inputs and 2 outputs– No support tag

GV-AS100

• GV-AS100– Program Mode

*227 Access the card manager function

*276 Access Security Mode

*347 Display system information

*738 Access Parameter Setting

*737 Restores GV-AS100 to factory default

GV-AS100

• GV-AS100– Program Mode

*837 Test numeral keys to see if they can be displayed properly

* Used to cancel the selection or go back to previous page

0 Used to go to the next page

# Used to save the data that was modified or programmed in the system and quit.

GV-AS100

• GV-AS100 With GV-ASBox– Support Doors 1 door to 2

doors– The card information 1000 to

40000– The internet connection

RS485 to TCP/IP– I/O 3 IN / 2 Out to 11 IN / 10

Out

GV-AS100GV-ASBox

• GV-AS100 With GV-ASBox–Wigand interface 2 in total– RS485 interface 1 in total– GV-GF 4 in total ( ASBox )

GV-AS100GV-ASBox

• GV-AS100 With GV-ASBox–Web Setting Switch• When this switch is on, you

can modify advance setting of GV-AS100 through the web interface. When the switch is off, advance setting are not accessible.

– Briefly went through web interface of GV-AS100 with GVAS- box. ( Very similar to AS400 )

GV-AS100GV-ASBox

AS-H04AS-H04

Access Control

AccessoriesAccessories

Accessories

• GV-Keypad

• GV-Battery

GV-Keypad

• GV-Keypad– Load default in AS200 and

ASBox– Upgrade Firmware– Setting Parameter, such as ID,

local time– Display System information,

such as memory status, IP address, firmware version…etc

GV-Battery

• GV-Battery– Act as UPS– 4 hours max Life span– Can be used in GV-AS200

Controller and other GeoVision device.

– Recommended third party battery• Yuasa NPH 5-12• GP1245 ( CSB )

• GV-Battery–Minimum Requirement for the

third-party battery• Voltage 12v with suggested 5A• Must have Terminal for Power

cable connection• The size of Battery

approximately around the below– Length 3.54”– Width 2.75”– Height 3.93”

GV-Battery

AS-H05AS-H05

Access Control

Advance Section – DemoAdvance Section – Demo

1) How to connect GV-Reader via RS-485?

2) How to connect GV-Reader via Wiegand?

3) How to setup I/O in GV-AS 200 controller?

4) How to setup I/O in GV-AS400 controller?

5) How to setup I/O in GV-AS100 with ASBox controller?

6) How to add / delete a card in GV-AS100?

6) How to enable / disable a card in GV-AS100?

7) How to restore Factory Default in GV-AS100?

Advance Section - Demo

Access Control

SummarySummaryAS-H06AS-H06

• Review All different Hardware’s features

Summary

• Review All different Hardware’s features

Summary

Access Control

FAQFAQ