Vertically Integrated INNOMAG pumps are made and assembled in
our factory in the USA
Slide 3
TB-Mag Series -Thrust Balancing Highest Quality Components
Slide 4
About Innomag: The Company Cont. Fast prototyping Fast lead
times Close cooperation with vendors Highly Experienced Engineering
design team
Slide 5
About Innomag Pump testing Pump Testing All wet-ends run tested
Disassembled and Inspected Hydrostatic tested to 450 psi (31 bar)
50Hz and variable speed testing available.
Slide 6
TB-Mag Series - Overview ASME/ANSI and ISO models. Continuous
duty process pumps
Slide 7
TB-mag Series - Construction and features Thrust balanced
Solids handling unique to mag-drives Permeation protected magnets
Single piece impeller Totally open suction, lowest NPSHr
Construction and Features
Slide 8
TB-Mag Series -Thrust Balancing By creating distinct pressure
zones in the pump, we can use those pressures to regulate &
control the forces on the impeller As the impeller moves forward,
the pressure surrounding the inner magnet is reduced. This creates
a restoring force. For momentary excursions, the impeller will
bounce back. For prolonged changes, impeller will seek new
equilibrium position Thrust Balancing
Slide 9
TB-Mag Series - Thrust Balancing Close up Thrust Balancing
Slide 10
TB-Mag Series - Solids Handling 2D View Solids Handling Wear
rings create a clearance of only 0.005 (.127mm), anything larger
cant hurt the magnets or lock up the bearings.
Slide 11
TB-Mag Series - Solids Handling Intro TB-mags can handle solids
up to 30% If it can travel through the vanes of the impeller, the
pump can handle it Solids must be softer than SiC Start-up and
shut-down must be evaluated Erosion must still be considered
Superior Solids Handling
Slide 12
TB-Mag Series - Tru-Seal Permeation Protection All
fluoroplastics are inherently permeable. While the fluoroplastics
are extremely chemical resistant, the magnets are not. Magnets are
covered with a stainless can, welded air tight, before being
encapsulated in plastic. This patented process is the best
permeation protection available. Greatly extends the impeller life
due to fluorine or chlorine ions that permeate the plastic and
attack the magnets. Lifespan for an unprotected impeller is between
6- 14 months. 2 piece impellers do not save you money as failures
usually result in damage to both the impeller AND magnet assembly,
completely negating the benefits of a 2 piece impeller. Tru-Seal
Permeation Protection INNOMAG Single Piece Impeller
Slide 13
TB-Mag Series - Cantilevered Design Unique Design Fully open
suction Lowest NPSHr Better Efficiencies INNOMAGCOMPETITION
Cantilevered Shaft Design
Slide 14
U-Mag Series - Features Sub-ANSI model Thrust forward design
Universal flanges for complete compatibility Virgin PFA option for
semiconductor, pharmaceutical, or other high purity industry Same
chemical compatibility as TB-mag with double welded impeller Low
Cost Features The U-Mag Series
Slide 15
U-Mag Series - Construction U-Mag Construction Mates NEMA
C-faced or IEC D-flange motors directly (no spacer plates
required). Universal foot supports entire pump load. Fully bonded
ETFE or optional High Purity PFA liner - minimum of 1/8 (3 mm)
thick and rated to full vacuum. Fully open suction for lowest
NPSHr. Optional High Purity PFA Universal chemical resistance with
fluoroplastic ETFE as standard.
Slide 16
U-Mag Series - PFA PFA High purity fluoroplastic Ultra low
contaminants, tested to less than 2 PPB. Excellent for semi-
conductor, LCD and circuit board manufacturing
Slide 17
Applications - Semiconductor Industry High purity standards
require PFA material on process/recycle streams Acids and other
etching solutions(HF, HCL, etc.) Acetone Hydrogen Peroxide MEK,
methanol, peroxide, TMAH Xylene Caustic Semiconductor/PCB
Industry
Slide 18
Case Studies - Fortune 500 Customers I Some INNOMAG electronics
customers
