A100 User Guide

7/27/2019 A100 User Guide

1/200

TOSHIBA

Satellite A100/

Satellite Pro A100

Portable Personal Computer

Users Manual


2/200

ii Users Manual

Copyright

2006 by TOSHIBA Corporation. All rights reserved. Under the copyrightlaws, this manual cannot be reproduced in any form without the prior written

permission of TOSHIBA. No patent liability is assumed, with respect to the useof the information contained herein.

TOSHIBA Satellite A100/Satellite Pro A100 Portable Personal Computer UsersManual

First edition December 2006

Copyright authority for music, movies, computer programs, data bases and other

intellectual property covered by copyright laws belongs to the author or to the

copyright owner. Copyrighted material can be reproduced only for personal use or

use within the home. Any other use beyond that stipulated above (including con-version to digital format, alteration, transfer of copied material and distribution on

a network) without the permission of the copyright owner is a violation of copy-

right or authors rights and is subject to civil damages or criminal action. Please

comply with copyright laws in making any reproduction from this manual.

Disclaimer

This manual has been validated and reviewed for accuracy. The instructions anddescriptions it contains are accurate for the TOSHIBA Satellite A100/SatellitePro A100 Portable Personal Computer at the time of this manuals production.However, succeeding computers and manuals are subject to change withoutnotice. TOSHIBA assumes no liability for damages incurred directly or indi-rectly from errors, omissions or discrepancies between the computer and themanual.

Trademarks

IBM is a registered trademark, and IBM PC and PS/2 are trademarks of Interna-tional Business Machines Corporation.Intel, Intel SpeedStep and Intel Core and Centrino are trademarks or registered

trademarks of Intel Corporation or its subsidiaries in the United States and other

countries/regions.

Windows and Microsoft are registered trademarks of Microsoft Corporation.Photo CD is a trademark of Eastman Kodak.Memory Stick is a registered trademark and i.LINK is a trademark of SonyCor-

poration.


3/200


4/200

iv Users Manual

Place the AC adapter in a ventilated area, such as a desk top or on the floor,when you use it to run the computer or to charge the battery. Do not coverthe AC adapter with papers or other items that will reduce cooling; also, donot use the AC adapter while it is inside a carrying case.

Use only the AC adapter and batteries that are approved for use with thiscomputer. Use of another type of battery or AC adapter may risk fire orexplosion.

Before you connect the computer to a power source, ensure that the voltagerating of the AC adapter matches that of the available power source. 115 V/60 Hz in most of North and South America and some Far Eastern countriessuch as Taiwan. 100 V/50 Hz in eastern Japan and 100 V/60 Hz in westernJapan. 230 V/50 Hz in most of Europe, the Middle East, and the Far East.

If you use an extension cable with your AC adapter, ensure that the totalampere rating of the products plugged in to the extension cable does notexceed the ampere rating of the extension cable.

To remove power from the computer, turn it off, remove the battery, and dis-connect the AC adapter from the electrical outlet.

To help avoid the potential hazard of electric shock, do not connect or dis-connect any cables or perform maintenance or reconfiguration of this prod-uct during an electrical storm.

When setting up the computer for work, place it on a level surface.


5/200

Users Manual v

FCC information

Product Name:Satellite A100/Satellite Pro A100Model number:PSAAK

FCC notice Declaration of Conformity Informa-tionThis equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential instal-lation. This equipment generates, uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to cor-rect the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING: Only peripherals complying with the FCC class B limits maybe attached to this equipment. Operation with non-compliant peripheralsor peripherals not recommended by TOSHIBA is likely to result in inter-

ference to radio and TV reception. Shielded cables must be used betweenthe external devices and the computers external monitor port, USB port,

serial port, parallel port, PS/2 mouse/keyboard port and microphonejack. Changes or modifications made to this equipment, not expressly

approved by TOSHIBA or parties authorized by TOSHIBA could void theusers authority to operate the equipment.

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation.


6/200


7/200


8/200


9/200

Users Manual ix

Pursuant to FCC CFR 47, Part 68:

When you are ready to install or use the modem, call your local telephone com-pany and give them the following information:

The telephone number of the line to which you will connect the modem

The registration number that is located on the device

The FCC registration number of the modem will be found on either thedevice which is to be installed, or, if already installed, on the bottom of thecomputer outside of the main system label.

The Ringer Equivalence Number (REN) of the modem, which can vary. Forthe REN of your modem, refer to your modems label.

The modem connects to the telephone line by means of a standard jack called the

US:AGSMDO1BATHENS.Type of service

Your modem is designed to be used on standard-device telephone lines. Connec-tion to telephone company-provided coin service (central office implementedsystems) is prohibited. Connection to party lines service is subject to state tariffs.If you have any questions about your telephone line, such as how many pieces ofequipment you can connect to it, the telephone company will provide this infor-mation upon request.

Telephone company procedures

The goal of the telephone company is to provide you with the best service it can.In order to do this, it may occasionally be necessary for them to make changes intheir equipment, operations, or procedures. If these changes might affect yourservice or the operation of your equipment, the telephone company will give younotice in writing to allow you to make any changes necessary to maintain unin-terrupted service.

If problems arise

If any of your telephone equipment is not operating properly, you should imme-diately remove it from your telephone line, as it may cause harm to the telephonenetwork. If the telephone company notes a problem, they may temporarily dis-continue service. When practical, they will notify you in advance of this discon-nection. If advance notice is not feasible, you will be notified as soon as possible.When you are notified, you will be given the opportunity to correct the problemand informed of your right to file a complaint with the FCC. In the event repairs

are ever needed on your modem, they should be performed by TOSHIBA Corpo-ration or an authorized representative of TOSHIBA Corporation.


10/200


11/200


12/200


13/200


14/200


15/200


16/200


17/200

Users Manual xvii

Toshiba Samsung TS-L462D

TEAC DW-224ER

Location of the required label

PRODUCT IS CERTIFIED BY THEMANUFACTURER TO COMPLY WITHDHHS RULES 21 CFR SUBCHAPTERJ APPLICABLE AT THE DATE OFMANUFACTURE.

MANUFACTURED:

TOSHIBA SAMSUNG STORAGE

TECHNOLOGY CORPORATION 580,HORIKAWA-CHO, SAIWAI-KU,KAWASAKI-SHI, KANAGAWA, 212-0013, JAPAN


COMPLIES WITH FDA RADIATIONPERFORMACE STANDARS, 21C CFRSUBCHAPTER J,

MANUFACTURED:

HITACHI-LG Data Storage20, YOIDO-DONG, YOUNG-DUNGPO-GU,SEOUL, KOREA


18/200


19/200


20/200

xx Users Manual

Pioneer DVR-K17


COMPLIES WITHFDA RADIATIONPERFORMANCE STANDARDS, 21CFR SUBCHAPTER J.

MANUFACTURED:

Manufactured byPIONEER CORPORATION 4-1.

Meguro 1-chome, Meguro-kuTOKYO 153-8654, JAPAN


21/200

Users Manual xxi

CAUTION: This appliance contains a lasersystem and is classified as a CLASS 1 LASERPRODUCT. To use this model properly, readthe instruction manual carefully and keep thismanual for your future reference. In case of anytrouble with this model, please contact yournearest AUTHORIZED service station. To

prevent direct exposure to the laser beam, donot try to open the enclosure.

VORSICHT: Dieses Gert enthlt ein Laser-System und ist als LASERSCHUTZKLASSE 1

PRODUKT klassifiziert. Fr den richtigen

Gebrauch dieses Modells lesen Sie bitte dieBedienungsanleitung sorgfltig durch undbewahren diese bitte als Referenz auf. Falls

Probleme mit diesem Modell auftreten, benach-richtigen Sie bitte die nchste autorisierteService-Vertretung. Um einen direkten Kon-takt mit dem Laserstrahl zu vermeiden darf dasGert nicht geffnet werden.

ADVARSEL: Denne mrking er anbragt udv-endigt p apparatet og indikerer, at apparatetarbejder med laserstrler af klasse 1, hviketbetyder, at der anvendes laserstrlier afsvagesteklasse, og at man ikke p apparatets ydersidekan bilve udsat for utilladellg kraftig strling.

APPARATET BOR KUN BNES AF FAGFOLK

MED SRLIGT KENDSKAB TIL APPARATERMED LASERSTRLER!

Indvendigt i apparatet er anbragt den her gen-givne advarselsmkning, som advarer imod atforetage sdanne indgreb i apparatet, at mankan komme til at udstte sig for laserstrling.

CLASS 1 LASTER PRODUCT

LASERSCHUTZKLASSE 1

PRODUKTTO EN 60825

ADVERSEL: USYNLIGLASERSTRLING VED BNING,NR SIKKERHEDSAF-BRYDERER UDE AF FUNKTION.UNDG UDSTTELSE FORSTRLING


22/200


23/200


24/200


25/200

Users Manual xxv

Shut Down mode (Boot mode) ......................................3-7Sleep mode....................................................................3-7

Hibernation mode ............................................................3-9

Starting Hibernation Mode ............................................3-10Automatic Hibernation Mode ........................................3-11

Restarting the computer ...............................................3-11

System Recovery Options ............................................3-12

Chapter 4 Operating Basics

Using the Touch Pad .......................................................4-1

Using the USB diskette drive..........................................4-2

Connecting 3 1/2" diskette drive ....................................4-2Disconnecting 3 1/2" diskette drive................................4-3

Using optical media drives .............................................4-3

Loading discs.................................................................4-4Removing discs .............................................................4-7

AV Button function (Provided with some models)..........4-8

Writing CDs on CD-RW/DVD-ROM drive........................4-9Before writing or rewriting..............................................4-9When writing or rewriting .............................................4-10Disclaimer (CD-RW/DVD-ROM drive) .........................4-11

Writing CD/DVDs on DVD Super Multi (+-R DL) drive.4-11

Important message (DVD Super Multi (+-R DL) drive) 4-11Before writing or rewriting............................................4-12

When writing or rewriting .............................................4-14Disclaimer (DVD Super Multi (+-R DL) drive) ..............4-15TOSHIBA Disk Creator ................................................4-15Data Verification ..........................................................4-16When Using Ulead DVD MovieFactory for TOSHIBA..4-17

Media care ......................................................................4-20

CD/DVDs .....................................................................4-20Diskettes......................................................................4-20


26/200


27/200


28/200


29/200


30/200


31/200

Users Manual xxxi

Preface

Congratulations on your purchase of the TOSHIBA Satellite A100/Satellite ProA100 computer. This powerful, lightweight notebook computer is designed to

provide years of reliable, high-performance computing.

This manual tells how to set up and begin using your Satellite A100/Satellite ProA100 computer. It also provides detailed information on configuring your com-

puter, basic operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if youre new to portable computing, firstread over theIntroduction and The Grand Tourchapters to familiarize yourselfwith the computers features, components and accessory devices. Then read Get-ting Startedfor step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the preface tolearn how this manual is organized, then become acquainted with this manual by

browsing through its pages. Be sure to look over the Special Features section oftheIntroduction, to learn about features that are uncommon or unique to thecomputers and carefully readHW Setup and Passwords. If you are going to

install PC cards or connect external devices such as a printer, be sure to readChapter 8, Optional Devices.

Manual contentsThis manual is composed of ten chapters, eight appendixes, a glossary, and anindex.

Chapter 1,Introduction, is an overview of the computers features, capabilities,

and options.Chapter 2, The Grand Tour, identifies the components of the computer and

briefly explains how they function.

Chapter 3, Getting Started, provides a quick overview of how to begin operatingyour computer and gives tips on safety and designing your work area.

Chapter 4, Operating Basics, includes tips on care of the computer and on usingthe Touch Pad, optical media drive, external diskette drive, Wireless LAN,LANs, Audio/Video controls, and internal modem.

Chapter 5, The Keyboard, describes special keyboard functions including thekeypad overlay and hot keys.


32/200


33/200

Users Manual xxxiii

Preface

Key operation

Some operations require you to simultaneously use two or more keys. We iden-tify such operations by the key top symbols separated by a plus sign (+). Forexample, Ctrl + C means you must hold down Ctrl and at the same time press C.If three keys are used, hold down the first two and at the same time press thethird.

ABC When procedures require an action such as clicking an icon or enteringtext, the icons name or the text you are to type in is represented in thetype face you see to the left.

Display

ABC Names of Windows or icons or text generated by the computer thatappears on its display screen is presented in the type face you see to theleft.

Messages

Messages are used in this manual to bring important information to your atten-tion. Each type of message is identified as shown below.

CAUTION:Pay attention! A caution informs you that improper useof equipment or failure to follow instructions may cause data loss ordamage your equipment.

NOTE:Please read. A note is a hint or advice that helps you makebest use of your equipment.

Terminology

This term is defined in this document as follows:

Start The word "Start " refer to the " "button in Microsoft Windows

VisataTM.


34/200

Users Manual xxxv

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and with-stand the rigors of portability. However, certain precautions should be observed

to further reduce the risk of personal injury, damage to the computer or imparedperformance.

Be certain to read the general precautions below and to note the cautionsincluded in the text of the manual.

Stress injury

Carefully read theInstruction Manual for Safety & Comfort. It contains informa-tion on prevention of stress injuries to your hands and wrists than can be caused

by extensive keyboard use. Chapter 3, Getting Started, also includes informationon work space design, posture and lighting that can help reduce physical stress.

Heat injury

Avoid prolonged physical contact with the computer. If the computer is usedfor long periods, its surface can become very warm. While the temperaturewill not feel hot to the touch, if you maintain physical contact with the com-

puter for a long time (if you rest the computer on your lap, or if you keepyour hands on the palm rest, for example) your skin might suffer low-heatinjury.

If the computer has been used for a long time, avoid direct contact with themetal plate supporting the I/O ports. It can become hot.

The surface of the AC adaptor can become hot when in use. This conditiondoes not indicate a malfunction. If you need to transport the AC adaptor, dis-connect it and let it cool before moving it.

Do not lay the AC adaptor on a material that is sensitive to heat. The mate-rial could be damaged.


35/200

General Precautions

xxxvi Users Manual

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to strong impact.Excessive pressure or impact can cause damage to computer components or oth-erwise cause malfunctions.

PC card overheating

Some PC cards can become hot with prolonged use. Overheating of a PC cardcan result in errors or instability in the PC card operation. Also be careful whenyou remove a PC card that has been used for a long time.

Mobile phone

Use of mobile phones can interfere with the audio system. Computer operation isnot impaired but it is recommended that a distance of 30 cm be maintained

between the computer and a mo-bile phone in use.


36/200

Users Manual 1-1

INTROD

UCTION

Chapter 1

IntroductionThis chapter provides an equipment checklist, and it identifies the computersfeatures, options and accessories.

CAUTION: Some of the features described in this manual may notfunction properly if you use an operating system that was not pre-

installed by TOSHIBA.

Equipment checklistCarefully unpack your computer. Save the box and packing materials for futureuse.

Hardware

Check to make sure you have all the following items:

Satellite A100/Satellite Pro A100 Portable Personal Computer

Universal AC adaptor and power cord

Modular cable (Provided with some models)


37/200


38/200


39/200


40/200


41/200


42/200

Users Manual 1-7

Introduction

INTRODUCT

ION

Communications

LAN The computer is equipped with a LAN card that sup-ports Ethernet LAN (10 Mbit/s, 10BASE-T)or FastEthernet LAN (100 Mbit/s, 100BASE-TX). It is prein-

stalled as a standard device in some markets. (depend onmodel you purchased)

Wireless LAN Some computers in this series are equipped with a Wire-less LAN mini card that is compatible with other LANsystems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radiotechnology that complies with the IEEE 802.11 Stan-

dard (Revision A, B and G). Automatic Transmit Rate Select mechanism in thetransmit range of 54, 48, 36, 24, 18, 12, 9 and 6Mbit/s (Revision B/G, A/B/G combo type).

Automatic Transmit Rate Select mechanism in thetransmit range of 11, 5.5, 2 and 1 Mbit/s (RevisionB).

Frequency Channel Selection (5 GHz: Revision A/

2.4 GHz: Revision B/G). Roaming over multiple channels.

Wired Equivalent Privacy (WEP) data encryption,based on the 128 bit encryption algorithm (Atherosmodule type).

Advanced Encryption Standard (AES) data encryp-tion, based on 256 bit encryption algorithm (Atherosmodule type).


43/200

Introduction

1-8 User Manual

INTRODUCTION

Security

Software

Modem Some computers in this series are equipped with aninternal modem. The internal modem provides capabil-ity for data and fax communication. It supports V.90(V.92). Refer to V.90 section inAppendix C. The speed

of date transfer and fax depends on analog telephoneline conditions. It has a modem jack for connecting to atelephone line. It is preinstalled as a standard device insome markets. Both of V.90 and V.92 are supported onlyin USA, Canada and France. Only V.90 is available inother regions.

Wireless Communi-cation Switch

This switch turns the Wireless LAN function on and off.(Provided with some models)

Security lock slot Connects an optional security lock to anchor the com-puter to a desk or other large object.

Operating System WindowsVistaTM is available. Refer to the preinstalledsoftware section at the front of this chapter.

TOSHIBA Utilities A number of utilities and drivers are preinstalled tomake your computer more convenient to use. Refer tothe Utilities section in this chapter.

Plug and Play When you connect an external device to the computer orwhen you install a component, Plug and Play capabilityenables the system to recognize the connection and

make the necessary configurations automatically.


44/200


45/200


46/200


47/200


48/200

Users Manual 1-13

Introduction

INTRODUCT

ION

Options

TOSHIBADVD-RAM Utility

TOSHIBA DVD-RAM Utility has the function of Phys-ical Format and Write-Protect to DVD-RAM. This util-ity is contained the setup module of TOSHIBA DiscCreator.

You can boot TOSHIBA DVD-RAM Utility from themenu bar as follows: [Start]-[All Programs]-[TOSHIBA]-[CD&DVD Applications]-[DVD-RAMUtility].

TOSHIBAConfigFree

ConfigFree is a suite of utilities to allow easy control ofcommunication device and network connections. Con-figFree also allows you to find communication prob-lems and create profiles for easy switching between

location and communication networks.You can boot ConfigFree from the menu bar as follows:[Start] - [All Programs] - [TOSHIBA]-[Networking]-[ConfigFree].

Windows MobilityCenter

This section describes the Windows Mobility Center.Mobility Center is a utility for accessing several mobilePC settings quickly in one window. A default maximum

of eight tiles are provided by the operating system, andan additional two tiles are added to your Mobility Cen-ter.

Lock Computer: This can be used to lock your com-puter without turning it off. This has the same func-tion as the Lock button at the bottom of the right

pane in the start menu.

TOSHIBA Assist: This can be used to open

TOSHIBA Assist if it is already installed in yourcomputer.


49/200


50/200

Users Manual 2-1

THEGRAND

TOUR

Chapter 2

The Grand TourThis chapter identifies the various components of your computer. Become famil-iar with each component before you operate the computer.

Front with the display closed

Figure 2-1 shows the computers front with its display panel in the closed posi-tion.

Figure 2-1 Front of the computer with display closed

Display latch This latch secures the LCD panel in its closed position.Slide the latch to open the display.

Volume control Use this dial to adjust the volume of the system speaker

and headphones.Microphone jack A standard 3.5 mm mini microphone jack enables con-

nection of a monaural microphone or other device foraudio input.

Headphone jack A standard 3.5 mm mini headphone jack enables connec-tion of a stereo headphone (16 ohm minimum) or otherdevice for audio output. When you connect headphones,the internal speaker is automatically disabled.

DISPLAYLATCH VOLUMECONTROL

HEADPHONEMICROPHONESYSTEM INDICATORS


51/200

The Grand Tour

2-2 Users Manual

THEGRANDTOUR

Left sideFigure 2-2 shows the computers left side.

Figure 2-2 The left side of the computer

System

Indicators

Four LEDs let you monitor the DC IN, Power status,Main battery and Disk. Details are in the System indica-tors sections.

External monitor port This 15-pin port lets you connect an external moni-tor.

Fan vent Provides air flow for the fan.

CAUTION:Be careful not to block the fan vent. Also be careful tokeep foreign objects out of the vents. A pin or similar object candamage the computers circuitry.

Video-out jack Plug a 4-pin S-Video connector into this jack.

i.LINK (IEEE 1394)

Port

Connect an external device, such as a digital video

camera to this port for high-speed data transfer.Some models are equipped with a i.LINK port.(Provided with some models)

Note: When multiple IEEE1394 devices are connected to a PC, thedevices may not correctly be identified. This problem may occur

when WindowsVistaTMis restarted while the devices are connectedor when the power to the IEEE1394 devices is turned on before the

PC is turned on. If it occurs, disconnect the IEEE1394 cables and

then reconnect them

FANVENT

I.LINK (IEEE 1394) PORT

PC CARD

SLOTVIDEO-OUTJACK

EXTERNALMONITOR PORT


52/200

Users Manual 2-3

The Grand Tour

THEGRANDTO

UR

PC Card Slot The PC card slot can accommodate one 5 mm PCcard (Type II). The slot supports 16-bit PC cardand 32-bit CardBus PC card.

CAUTION:Keep foreign objects out of the PC card slot. A pin or

similar object can damage the computers circuitry.


53/200


54/200


55/200


56/200

Users Manual 2-7

The Grand Tour

THEGRANDTO

UR

UndersideFigure 2-5 shows the underside of the computer. Make sure the display is closed

before turning over your computer.

Figure 2-5 The underside of the computerBattery pack The battery pack powers the computer when the AC

adaptor is not connected. The Batteries section in Chap-ter 6,Power and Power-Up Modes, describes how toaccess the battery pack. Additional battery packs can be

purchased from your TOSHIBA dealer to extend thecomputers battery operating time.

Battery pack

cover latch

Slide this latch to release the battery pack.

This latch moves only when the computer is upsidedown.

Battery lock Slide the battery pack lock to unlocked position to freethe battery latch.

Memory module

cover

This cover protects two memory module sockets. Oneor two modules are preinstalled.

MEMORY

MODULE

COVER

BATTERY

PACK

BATTERYPACK

LOCK

BATTERY

RELEASE LATCH


57/200


58/200


59/200


60/200


61/200

The Grand Tour

2-12 Users Manual

THEGRANDTOUR

The figures below show the positions of the keypad overlay indicators and theCapsLock indicator.

When the F10 key indicator glows the keypad overlay lets you control the cursor.

When the F11 key indicator glows the keypad overlay lets you enter numbers.

Figure 2-8 Keypad overlay indicators

When the CapsLock indicator glows the keyboard is in all-caps mode.

Figure 2-9 CapsLock indicator

Keyboard indicator

Arrow mode When the Arrow mode indicator lights green, you canuse the keypad overlay (white labeled keys) as cursorkeys. Refer to theKeypad overlay section in Chapter 5,The Keyboard.

Numeric mode You can use the keypad overlay (white labeled keys) fornumeric input when the Numeric mode indicator

lights green. Refer to theKeypad overlay section inChapter 5, The Keyboard.

Caps Lock This indicator glows green when the alphabet keys arelocked in uppercase.

ARROWMODE

NUMERICMODE

CAPS LOCK

INDICATOR


62/200


63/200

The Grand Tour

2-14 Users Manual

THEGRANDTOUR

Optical Media driveCD-RW/DVD-ROM drive, DVD Super Multi (+-R DL) drive. An ATAPI inter-face controller is used for CD/DVD-ROM operation. When the computer isaccessing a CD/DVD, an indicator on the drive glows.

Region codes for DVD drives and mediaCD-RW/DVD-ROM, DVD-ROM, DVD Super Multi (+-R DL) drive and mediaare manufactured according to the specifications of six marketing regions. Whenyou purchase DVD-Video, make sure it matches your drive, otherwise it will not

play properly.

Writable discs

This section describes the types of writable CD/DVD discs. Check the specifica-tions for your drive to for the type of discs it can write. Use TOSHIBA Disc Cre-ator to write compact discs. Refer to Chapter 4, Operating Basics.

CDs

CD-R discs can be written only once. The recorded data cannot be erased orchanged.

CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi

speed CD-RW discs or high-speed 4- to 10-speed discs. The write speed ofthe ultra-speed CD-RW discs (Ultra-speed is CD-RW/DVD-ROM driveonly) is maximum 24-speed.

DVDs

DVD-R, DVD+R and DVD+R DL discs can be written only once. Therecorded data cannot be erased or changed.

DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

Code Region1 Canada, United States

2 Japan, Europe, South Africa, Middle East3 Southeast Asia, East Asia4 Australia, New Zealand, Pacific Islands, Central America,

South America, Caribbean5 Russia, Indian Subcontinent, Africa, North Korea, Mongolia6 China


64/200


65/200

The Grand Tour

2-16 Users Manual

THEGRANDTOUR

AC adaptorThe AC adaptor converts AC power to DC power and reduces the voltage sup-

plied to the computer. It can automatically adjust to any voltage from 100 to 240volts and to a frequency of either 50 or 60 hertz, enabling you to use the com-

puter in almost any region.

To recharge the battery, simply connect the AC adaptor to a power source and thecomputer. See Chapter 6Power and Power-Up Modes for details.

Figure 2-11 The AC adaptor(2-pin plug)

Figure 2-12 The AC adaptor(3-pin plug)

CAUTION: Use of the wrong adaptor could damage your computer.TOSHIBA assumes no liability for any damage in such case. Theoutput rating for the computer is 19 volts DC.

CAUTION:Please use only the AC adaptor supplied with the com-puter or an AC adaptor certified by TOSHIBA.


66/200


67/200


68/200


69/200

Getting Started

3-4 Users Manual

GETTINGSTARTED

LightingProper lighting can improve legibility of the display and reduce eye strain.

Position the computer so that sunlight or bright indoor lighting does notreflect off the screen. Use tinted windows, shades or other screen to elimi-nate sun glare.

Avoid placing the computer in front of bright light that could shine directlyin your eyes.

If possible, use soft, indirect lighting in your computer work area. Use alamp to illuminate your documents or desk, but be sure to position the lampso that it does not reflect off the display or shine in your eyes.

Work habitsA key to avoiding discomfort or injury from repetitive strain is to vary youractivities. If possible, schedule a variety of tasks into your work day. If you mustspend long periods at the computer, finding ways to break up the routine canreduce stress and improve your efficiency.

Sit in a relaxed posture. Good positioning of your chair and equipment asdescribed earlier can reduce tension in your shoulders or neck and ease backstrain.

Vary your posture frequently.

Occasionally stand up and stretch or exercise briefly.

Exercise and stretch your wrists and hands a number of times during the day.

Frequently, look away from the computer and focus your eyes on a distantobject for several seconds, for example 30 seconds every 15 minutes.

Take frequent short breaks instead of one or two long breaks, for example,two or three minutes every half hour.

Have your eyes examined regularly and visit a doctor promptly, if you sus-

pect you might be suffering from a repetitive strain injury.A number of books are available on ergonomics and repetitive strain injury orrepetitive stress syndrome. For more information on these topics or for pointerson exercises for such stress points as hands and wrists, please check with yourlibrary or book vendor. Also refer to the computers Instruction Manual forSafety & Comfort.


70/200


71/200


72/200

Users Manual 3-7

Getting Started

GETTINGSTARTED

Starting up for the first timeWhen you first turn on the power, the computers initial screen is the MicrosoftWindows VistaTM Startup Screen Logo.

Follow the on-screen directions.

Turning off the powerThe power can be turned off in one ofthree modes, either Shut Down(Boot )Mode, Hibernation Mode or Sleep Mode.

Shut Down mode (Boot mode)When you turn off the power in Shut Down mode, no data will be saved and the

computer will boot to the operating systems main screen the next time it isturned on.

1. If you have entered data, either save it to the hard disk or to other storagemedia.

2. Make sure all disk/disc activity has stopped before removing the CD/DVD

or floppy diskette...

3. Click Start then click the arrow button ( ) located in the power man-

agement buttons( ) and select Shut Down from the menu.

4. Turn off any peripheral devices connected to your computer.

Sleep mode

If you do have to interrupt your work, you are able to turn off the power withoutexiting from your Software by placing the computer into Sleep Mode. In this

Make sure the Hard Disk Drive indicator is off. If you turn off the

power while a disk(disc) is being accessed, you can lose data or

damage the disk. Never turn off the power while an application is running. Doing so

could cause loss of data.

Never turn off the power, disconnect an external storage device or

remove storage media during data read/write: Doing so can cause

data loss.

Do not turn the computer or peripheral devices back on immediately -

wait a short period to avoid any potential damage.


73/200


74/200

Users Manual 3-9

Getting Started

GETTINGSTARTED

1. Click Start then click the power button ( ) located in the power man-

agement button( ), or click the arrow button ( ) and selectsleep from the menu.

2. Close the computers LCD display panel. Please note that this feature mustbe enabled - please refer to the Power options (to access it, clickStart fol-lowed by Control Panel followed by System and Maintenance andthen click the Power Options).

3. Press the power button. Please note that this feature must be enabled -please refer to the Power options (to access it, clickStart followed byControl Panel followed by System and Maintenance and then click-the Power Options) .

When you turn the power back on, you can continue where you left when you

shut down the computer.

Sleep Mode limitations

Sleep Mode will not funation under the following conditions:

Power is turned back on immediately after shutting down.

Memory circuits are exposed to static electricity or electrical noise.

Hibernation modeThe Hibernatlon Mode feature saves the contents of memory to the hard diskdrive when the computer is turned off so that, the next time it is turned on, the

When the computer is in Sleep Mode, the power indicator will

blink orange.

If you are operating the computer on the battery power, you can

lengthen the overall operating time by turning it off into Hiberna-

tion Mode - Sleep Mode will consume more power while the com-

puter is off.


75/200

Getting Started

3-10 Users Manual

GETTINGSTARTED

previous state is restored. Please note that the Hibernation Mode feature does not

save the status of any peripheral devices connected to the computer.

Benefits of Hibernation ModeThe Hibernation Mode feature provides the following benefits:

Saves data to the hard disk drive when the computer automatically shutsdown because of a low battery condition.

You can return to your previous working environment immediately whenyou turn on the computer.

Saves power by shutting down the system when the computer receives noinput or hardware access for the time period set by the System Hibernste fea-

ture. Allows the use ofthe panel power off feature.

Starting Hibernation Mode

To enter Hibernation Mode, follow the steps below.

1. Click Start.

2. Click the narrow button ( ) in the power managment buttons

( ).

3. Select Hibernation from the menu.

Save your data. While entering Hibernation Mode, the computer

saves the contents of memory to the hard disk drive. However, for

safety sake, it is best to save your data manually. Data will be lost if you remove the battery or disconnect the AC

adaptor before the save is completed. Wait for the Hard Disk Drive

indicator to go out.

Do not install or remove a memory module while the computer is

in Hibernation Mode. Data will be lost.

You can also enable Hibernation Mode by pressingFn+F4 -

please refer to Chapter 5. The Keyboard, for futher details.


76/200

Users Manual 3-11

Getting Started

GETTINGSTARTED

Automatic Hibernation ModeThe Computer can be configured to enter Hibernation Mode automatically whenyou press the power button or close the lid. In order to define these settings, youcan follow the steps as described below:

1. Click Start and click the Control Panel.

2. Click System and Maintenance and clickPower Options.

3. Click Choose what the power buttons do orChoose what closingthe Iid does.

4. Enable the desired Hibernation Mode settings forwhen I press thepower button and When I close the lid.

5. Click the Save changes button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer will take amoment to save the current data in memory to the hard disk drive. During thistime, the Hard Disk Drive indicator will glow.Affer you turn off the computr, and the content of memory has been saved to the

hard disk drive, turn off the power to any peripheral devices.

Restarting the computerCertain conditions require that you reset the computer, for example if:

You change certain computer settings.

An error occurs and the computer does not respond to your keyboard com-mands.

If you need to restart the computer, there are three ways this can be achieved:

1. Click Start, then click the narrow( ) in the power managment but-

ton( ) and select Restsrt from the menu.

2. Press Ctrl + Alt + Del to display the menu window, then select Restart-from the Shut down options.

3. Press the power button and hold it down for five seconds. Once the com-

puter has turned itself off, wait between ten and fifteen seconds before turn-ing the power on again by pressing the power button.

Do not turn the computer or devices back on immediately. Wait a

moment to let all capacitors fully discharge.


77/200

Getting Started

3-12 Users Manual

GETTINGSTARTED

System Recovery OptionsAbout 1.5GB hidden partition is allocated on the hard disk drive for the SystemRecovery Options. This partition stores files which can be used to repair the sys-

tem in the event of a problem.

System Recovery Options

The System Recovery Options feature is installed on the hard disk when shippedfrom the factory. The System Recovery Options menu includes some tools torepair startup problems, run diagnostics or restore the system.You can see the more information about Startup Repair in Windows Help andSupport content.

The System Recovery Options can also be run manually to repair problems.1. Turn off the computer.

2. While holding the F8 key, turn the computer on again.3. The Advanced Boot Options menu will be displayed.

Use the arrow keys to select Repair Your Computerand press Enter.

Follow the on-screen instructions from this point onward.

Restoring the preinstalled software from the ProductRecovery disc

If preinstalled files are damaged, use the Product Recovery disc to restore them.To restore the operating system and all preinstalled software, follow the steps

below.You can not use System Recovery Options if restoring the pre-installed software

without System Recovery Options.1. Load the Product Recovery disc in the drive and turn off the computer's

power.

2. Switch on the computer and, when the In Touch with Tomorrow TOSHIBAprompt appears, press the F12 key to display the Boot Menu.

3. Use the up or down cursor key to select the CD-ROM/DVD drive in the dis-play menu.

The Window Vista Complete PC Backup feature can be used on

WindowsVistaTM Business Edition and Ultimate Edition.


78/200

Users Manual 3-13

Getting Started

GETTINGSTARTED

4. Follow the on-screen instructions.

When you reinstall the Windows operating system, the hard disk

will be reformatted and all data will be lost.

Drivers / utilities or when installing, you can setup the respective

drivers / utilities from the following folder. C:\TOSAPINS\***.


79/200


80/200

Operating Basics

4-2 Users Manual

OPERATINGBASICS

Using the USB diskette driveA 3 1/2" diskette drive connects to the computers USB port. It accommodates1.44-megabyte or 720-kilobyte diskettes. Refer to Chapter 2, The Grand Tour,

for more information.

Connecting 3 1/2" diskette driveTo connect the drive, plug the diskette drive connector into a USB port. Refer toFigure 4-2.

Note:Make sure the connector is right side up and properly alignedwith the socket. Do not try to force the connection, doing so candamage the connecting pins.

Figure 4-2 Connecting the USB diskette drive

Note:If you connect the diskette drive after turning on the computer,it will take about 10 seconds for the computer to recognize the drive.

Do not disconnect and reconnect before 10 seconds has elapsed.


81/200


82/200

Operating Basics

4-4 Users Manual

OPERATINGBASICS

Loading discsTo load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7.

1. a. When the power is on, press the DVD-ROM eject button to open thedrawer slightly.

Figure 4-3 Pressing the DVD-ROM eject button

b. Pressing the eject button will not open the drawer when the DVD-ROMdrives power is off. If the power is off, you can open the drawer byinserting a slender object (about 15 mm) such as a straightened paperclip into the eject hole just to the right of the eject button.

Figure 4-4 Manual release with the eject hole

EJECTBUTTON

EJECT HOLE


83/200

Users Manual 4-5

Operating Basics

OPERATINGBASICS

2. Grasp the drawer gently and pull until it is fully opened.

Figure 4-5 Pulling the drawer open

3. Lay the CD/DVD, label side up, in the drawer.

Figure 4-6 Inserting a CD/DVD

Note: When the drawer is fully opened, the edge of the computer willextend slightly over the CD/DVD tray. Therefore, you will need toturn the CD/DVD at an angle when you place it in the tray. After

seating the CD/DVD, however, make sure it lies flat, as shown in fig-ure 4-6.

CAUTIONS: 1. Do not touch the laser lens. Doing so could cause mis-alignment.

2. Do not keep foreign matter from entering the drive. Check

the back edge of the tray to make sure it carries no debrisbefore closing the drive.


84/200


85/200

Users Manual 4-7

Operating Basics

OPERATINGBASICS

Removing discsTo remove the CD/DVD, follow the steps below and refer to figure 4-8.

CAUTION:Do not press the eject button while the computer is

accessing the DVD-ROM drive. Wait for the optical media driveindicator to go out before you open the drawer. Also, if the CD/DVDis spinning when you open the drawer, wait for it to stop before youremove it.

1. To pop the drawer partially open, press the eject button. Gently pull thedrawer out until it is fully opened.

CAUTIONS: 1. When the drawer pops open slightly, wait a moment tomake sure the CD/DVD has stopped spinning before pull-

ing the drawer fully open.

2. Turn off the power before you use the eject hole. If theCD/DVD is spinning when you open the drawer, the CD/

DVD could fly off the spindle and cause injury.

2. The CD/DVD extends slightly over the sides of the drawer so you can graspit. Hold the CD/DVD gently and lift it out.

Figure 4-8 Removing a CD/DVD

3. Push the center of the drawer to close it. Press gently until it locks intoplace.


86/200

Operating Basics

4-8 Users Manual

OPERATINGBASICS

AV Button function (Provided with some models)This section describes a button function.

Figure 4-9 AV Button

*Windows Media Player 11

Windows mode

Icon AV ButtonDVD

(WinDVD8)*CD/DVD

(WMP)

CD/DVD Detect andactivate media

Detect andactivate media

Play/Pause Play/Pause Play/PauseStop Stop Stop

Previous Previous chapter Previous tune

Next Next chapter Next tune


87/200


88/200

Operating Basics

4-10 Users Manual

OPERATINGBASICS

Be sure to close all other software programs except the writing software.

Do not run software such as a screen saver which can put a heavy load on theCPU.

Operate the computer at full power. Do not use power-saving features.

Do not write while virus check software is running. Wait for it to finish, thendisable virus detection programs including any software that checks filesautomatically in the background.

Do not use hard disk utilities, including those intended to enhance HDDaccess speed. They may cause unstable operation and damage data.

Write from the computers HDD to the CD. Do not try to write from shareddevices such as a LAN server or any other network device.

Writing with software other than TOSHIBA Disk Creator has not been con-

firmed. Therefore, operation with other software cannot be guaranteed.

When writing or rewriting

Please observe/consider the following when you write or rewrite to a CD-R/RW,DVD-R/-RW/-RAM or DVD+R/+RW disc.

Do not perform any of the following actions when writing or rewriting:

Change users in the Windows VistaTM operating system. Operate the computer for any other function, including using a mouse or

TouchPad or closing/opening the LCD panel. Start a communication application such as a modem. Apply impact or vibration to the computer. Install, remove or connect external devices such as PC card, USB

devices, an external display, i.Link devices or optical digital devices. Use the audio/video control button to reproduce music or voice. Open the drive.

Do not use shut down/log off and Sleep/Hibernation while writing or

rewriting. Make sure writing or rewriting is completed before going into Sleep/

hibernation. Writing is completed if you can open the drive tray.

Set the computer on a level surface and avoid places subject to vibra-tionsuch as airplanes, trains or cars. Do not use an unstable surface suchas a stand.

Keep mobile phones and other wireless communication devices away-from the computer.

Always copy data from the hard disk drive to the CD. Do not usecutand-paste as the original data will be lost if there is a write error.


89/200


90/200

Operating Basics

4-12 Users Manual

OPERATINGBASICS

Before writing or rewriting Based on TOSHIBAs limited compatibility testing, we suggest the follow-

ing manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM/+R DL/-R DL disc.

However, in no event does TOSHIBA guarantee the operation, quality orperformance of any disc. Disc quality can affect write or rewrite success

rates.

Note: This drive cannot use discs that allow writing of 8 speeds ormore (DVD-R, DVD+R), 6 speeds or more(DVD-RW) and 8 speedsor more(DVD+RW).

If the disc is poor in quality, dirty or damaged, writing or rewriting errorsmay occur. Be careful to check the disc for dirt or damage before you use it.

CD-R: TAIYO YUDEN CO., LTD.MITSUBISHI KAGAKU MEDIA CO.,LTDRICOH Co., Ltd.

CD-RW:(High-Speed,

MultiSpeed)

MITSUBISHI KAGAKU MEDIA CO.,LTDRICOH Co., Ltd.

CD-RW:(Ultra-Speed)

MITSUBISHI KAGAKU MEDIA CO.,LTD.

DVD-R DVD Specifications for Recordable Disc for GeneralVersion 2.0TAIYO YUDEN CO., LTD.Hitachi Maxell Ltd.Matsushita Electric Industrial Co., Ltd.

DVD+R MITSUBISHI KAGAKU MEDIA CO.,LTDRICOH Co., Ltd.DVD-RW DVD Specifications for Recordable Disc for Version 1.1

VICTOR COMPANY OF JAPAN, LIMITEDMITSUBISHI KAGAKU MEDIA CO.,LTD

DVD+RW MITSUBISHI KAGAKU MEDIA CO.,LTDRICOH Co., Ltd.

DVD-RAM DVD Specifications for DVD-RAM Disc for Version2.0, Version 2.1 or Version 2.2

Matsushita Electric Industrial Co., Ltd.Hitachi Maxell Ltd.

DVD+R DL MITSUBISHI KAGAKU MEDIA CO.,LTD.DVD-R DL MITSUBISHI KAGAKU MEDIA CO.,LTD.


91/200

Users Manual 4-13

Operating Basics

OPERATINGBASICS

The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVD-RAM is affected by the quality of the disc and the way it is used.

There are two types of DVD-R discs: authoring and general use discs. Donot use authoring discs. Only general use discs can be written to by a com-

puter drive. We can support only format 1 of DVD-R DL. Therefore you can not do the

additional writing. If your data is under DVD-R(SL) capacity, we suggest touse DVD-R(SL) media.

You can use DVD-RAM discs that can be removed from a cartridge andDVD-RAM discs designed without a cartridge. You cannot use a disc with a2.6 GB single-sided capacity or 5.2 GB double-sided capacity.

Other DVD-ROM drives for computers or other DVD players may not be

able to read DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs. Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in

whole or in part.

Data deleted (erased) from a CD-RW and DVD-RW, DVD+RW and DVD-RAM disc cannot be recovered. Check the content of the disc carefully

before you delete it. If multiple drives that can write data to discs are con-nected, be careful not to delete data from the wrong drive.

In writing to a DVD-R/-R DL/-RW, DVD+R/+R DL/+RW or DVD-RAM

disc, some disc space is required for file management, so you may not beable to write the full capacity of the disc.

Since the disc is based on the DVD standard, it will be filled with dummydata if the written data is less than about 1 GB. Even if you write only asmall amount of data, it might take time to fill in the dummy data.

DVD-RAM formatted by FAT32 cannot be read in Windows 2000 withoutDVD-RAM Driver Software.

When multiple drives that can write data to discs are connected, be careful

not to write to the wrong drive. Be sure to connect the universal AC adaptor before you write or rewrite.

Before you enter sleep/hibernation mode, be sure to finish DVD-RAM writ-ing. Writing is finished if you can eject DVD-RAM media.

Be sure to close all other software programs except the writing software.

Do not run software such as a screen saver, which can put a heavy load onthe CPU.

Operate the computer in the full-power mode. Do not use power-saving fea-tures.


92/200

Operating Basics

4-14 Users Manual

OPERATINGBASICS

Do not write while virus check software is running. Wait for it to finish, andthen disable virus detection programs including any software that checksfiles automatically in the background.

Do not use hard disk utilities, including those intended to enhance HDD

access speed. They may cause unstable operation and data damage. Write from the computers HDD to the CD/DVD. Do not try to write from

shared devices such as a LAN server or any other network device.

Writing with software other than TOSHIBA Disk Creator is not recom-mended.

When writing or rewritingPlease observe/consider the following when you write or rewrite to a CD-R/RW,

DVD-R/-R DL/-RW/-RAM or DVD+R/+R DL/+RW disc. Do not perform any of the following actions:

Change users in the Windows VistaTM operating system.

Operate the computer for any other function, including use of a mouseor Touch Pad, closing/opening the LCD panel.

Start a communication application such as a modem.

Apply impact or vibration to the PC.

Install, remove or connect external devices, including the following: PCcard, USB devices, external display, i.LINK devices, optical digitaldevices.

Use the Audio/Video control button to reproduce music or voice.

Open the CD-RW/DVD-ROM or DVD Super Multi (+-R DL) drive.

Do not use shut down/log off and sleep/hibernation while writing or rewrit-ing.

Make sure writing or rewriting is completed before going into sleep/hiberna-

tion. Writing is completed if you can open the CD-RW/DVD-ROM or DVDSuper Multi (+-R DL) drive tray.

Set the computer on a level surface and avoid places subject to vibrationsuch as airplanes, trains, or cars. Do not use an unstable surface such as astand.

Keep mobile phones and other wireless communication devices away fromthe computer.

Always copy data from the HDD to the DVD-RAM. Do not use cut-and-

paste. The original data will be lost if there is a write error.


93/200

Users Manual 4-15

Operating Basics

OPERATINGBASICS

Disclaimer (DVD Super Multi (+-R DL) drive)TOSHIBA does not bear responsibility for the following:

Damage to any CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/DVD-RAM disc that may be caused by writing or rewriting with this product.

Any change or loss of the recorded contents of CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/DVD-RAM disc that may be caused by writing orrewriting with this product, or for any business profit loss or business inter-ruption that may be caused by the change or loss of the recorded contents.

Damage that may be caused by using third party equipment or software.Given the technological limitations of current optical disc writing drives,you may experience unexpected writing or rewriting errors due to disc qual-ity or problems with hardware devices. Also, it is a good idea to make two or

more copies of important data, in case of undesired change or loss of therecorded contents.

TOSHIBA Disk CreatorNote the following limitations when you use TOSHIBA Disk Creator.

DVD-Video cannot be created using TOSHIBA Disk Creator.

DVD-Audio cannot be created using TOSHIBA Disk Creator.

You cannot use TOSHIBA Disk Creator Audio CD for Car or Home CDPlayer function to record music to the DVD-R/-R DL/-RW or DVD+R/+RDL/+RW disc.

Do not use the Exact Copy function of TOSHIBA Disk Creator to copyDVD-Video and DVD-ROM with copyright protection.

DVD-RAM disc cannot be backed up with the Exact Copy function ofTOSHIBA Disk Creator.

You cannot back up a CD-ROM or CD-R/RW to DVD-R/-R DL/-RW or

DVD+R/+R DL/+RW using the Exact Copy function of TOSHIBA DiskCreator.

You cannot back up DVD-ROM, DVD-Video or DVD-R/-R DL/-RW orDVD+R/+R DL/+RW to CD-R/RW using the Exact Copy function ofTOSHIBA Disk Creator.

TOSHIBA Disk Creator record in packet format.

You might not be able to use the Exact Copy function of TOSHIBA DiskCreator to back up a DVD-R/-R DL/-RW or DVD+R/+R DL/+RW disc that

was made with other software on a different DVD-R/-R DL/-RW orDVD+R/+RW recorder.


94/200

Operating Basics

4-16 Users Manual

OPERATINGBASICS

If you add data to a DVD-R/-R DL and DVD+R/+R DL disc that you havealready recorded to, you might not be able to read the added data under somecircumstances. It cannot be read in 16-bit operating systems, such as Win-dows 98 SE and Windows ME. In Windows NT 4, you will need ServicePack 6 or later to read added data. In Windows 2000, you will need ServicePack 2 or later to read it. Some DVD-ROM and CD-RW/DVD-ROM drivescannot read added data regardless of the operating system.

TOSHIBA Disk Creator does not support recording to DVD-RAM discs. Torecord to a DVD-RAM, use Explorer or other utility.

When you back up a DVD disc, be sure the source drive supports recordingto DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs. If the source drivedoes not support recording to DVD-R/-RW or DVD+R/+RW discs, it mightnot be backed up correctly.

When you back up a DVD-R, DVD-RW, DVD+R or DVD+RW, be sure touse the same type of disc.

You cannot partially delete any data written to a CD-RW, DVD-RW orDVD+RW disc.

Only DVD Super Multi (+-R DL) Drive

When TOSHIBA Disk Creator launched, it is possible that the disc tray ofthe DVD drive with the disc loaded is unable to be ejected even the "Eject"

button is pressed. To solve this problem, please click on the "eject" button( ) on the TOSHIBA Disk Creator main screen, or right click on the iconof the DVD drive where the disc loaded, select "Eject" of the pop-up menuunder "My Computer" or "Explore".

Data VerificationTo verify that data is written or rewritten correctly, follow the steps below beforeyou write or rewrite a Data CD/DVD.

1. Click the Options button ( ) on the TOSHIBA Disk Creator Assist toopen the Options panels.

2. Select the Data in the left-side menu.

3. Mark the Verify data written to the disc after burning check box in the DataOptions.

4. Click the OK button.


95/200

Users Manual 4-17

Operating Basics

OPERATINGBASICS

When Using Ulead DVD MovieFactory forTOSHIBA

How to make a DVD-Video

Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder:

1. Click Start->All Programs ->DVD MovieFactory for TOSHIBA->Ulead DVD MovieFactory for TOSHIBA Launcherto launch DVDMovieFactory.

2. Insert a DVD-RW or DVD+RW disc in Burner.

3. Click Video Disc -> Burn Video to Disc to launch Direct Recording

dialog box, choose DVD-Video/+VR to invoke Straight Capture toDisc Page.

4. Choose DVD-Video format.

5. Confirm the capture source is DV.

6. Press Capture button.

Simplified steps for making a DVD-Video from adding video source:

1. Click Start->All Programs ->DVD MovieFactory for TOSHIBA->Ulead DVD MovieFactory for TOSHIBA Launcherto launchDVD MovieFactory.

2. Click Video Disc -> New Project to invoke 2nd Launcher, choose yourproject type, then invoke DVD MovieFactory.

3. Add source from HD Disk by clickAdd Video files button to invokebrowser dialog box.

4. Choose the source video then go to Next page to apply Menu.

5. After choose the menu template, press Next button to go to Burning

Page.6. Choose the output type then press Burn button.

How to learn more about Ulead DVD MovieFactory

Please refer to the Help and Manual files for additional Ulead DVD MovieFac-tory information.

Important information for use

Note the following limitations when you write Video DVD:


96/200

Operating Basics

4-18 Users Manual

OPERATINGBASICS

1. Editing digital video.

Log in with Administrator rights to use DVD MovieFactor.

Make sure that your computer is running on AC power when using DVDMovieFactory.

Operate the computer at Full Power. Do not use power-saving features.

While you are editing DVD, you can display preview. However, if anotherapplication is running, the preview might not display properly.

DVD MovieFactory cannot edit or play copy protected content.

Do not enter sleep or hibernation mode while using DVD MovieFactory.

Do not operate DVD MovieFactory immediately after turning on the com-puter. Please wait until all Disc Drive activity has stopped.

When recording to a DV-Camcorder, to ensure you capture all of yourdata, let the camcorder record for a few seconds before you begin record-ing your actual data.

CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CDfunctions are not supported in this version.

While recording video to DVD, please close all other programs.

Do not run software like a screen saver because it can put a heavy load onthe CPU.

Do not support mp3 decode and encode.2. Before recording the video to DVD.

When you record DVD disc, please use only discs recommended by theDrive manufacturer.

Do not set the working drive to a slow device like a USB1.1 hard diskdrive or it will fail to write DVD.

Do not perform any of the following actions:

Operate the computer for any other function, including using a mouse toTouchPad or closing/Opening the LCD panel.

Bump or cause vibration to the computer.

Use the Mode control button and Audio/Video control button to repro-duce music or voice.

Open the DVD drive.

Install, remove or connect external devices, including the following: PCcard, SD card, USB device, external display, i.LINK. devices, optical dig-

ital devices. Please verify your disc after recording important data.


97/200

Users Manual 4-19

Operating Basics

OPERATINGBASICS

DVD-R/+R/+RW disc cannot be written in VR format.

Not support to output VCD and SVCD format.

3. About Straight to Disc.

Not support to record on DVD-R/+R disc.

Not support to record DVD+VR format by HDV.

HDV support to burn DVD-Video only.

DVD-VR format not support to add Menu.

4. About recorded DVDs.

Some DVD-ROM drives for personal computers or other DVD playersmay not be able to read DVD-R/+R/-RW/-RAM discs.

When playing your recorded disc on your computer, please use WinDVD

software application. If you use an over-used rewritable disc, the full formatting might be

locked. Please use a brand new disc.


98/200

Operating Basics

4-20 Users Manual

OPERATINGBASICS

Media careThis section provides tips on protecting data stored on your CD/DVDs and dis-kettes.

Handle your media with care. The following simple precautions will increase thelifetime of your media and protect the data stored on them:

CD/DVDs1. Store your CD/DVDs in the container they came in to protect them and

keep them clean.

2. Do not bend the CD/DVD.

3. Do not write on, apply a sticker to, or otherwise mark the surface of the CD/

DVD that contains data.4. Hold the CD/DVD by its outside edge or the edge on the center hole. Fin-

gerprints on the surface can prevent the drive from properly reading data.

5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavyobjects on your CD/DVDs.

6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth.Wipe from the center out, do not wipe in a circular direction around the CD/DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do

not use benzine, thinner or similar cleaner.

Diskettes1. Store your diskettes in the container they came in to protect them and keep

them clean. If a diskette is dirty, do not use cleaning fluid. Clean it with asoft damp cloth.

2. Do not slide back the diskettes protective metal covering or touch the dis-kettes magnetic surface. Fingerprints may prevent the diskette drive fromreading data from the diskette.

3. Data may be lost if the diskette is twisted; bent; or exposed to direct sun-light, extreme heat or cold.

4. Do not place heavy objects on your diskettes.

5. Do not eat, smoke, or use erasers near your diskettes. Foreign particlesinside the diskettes jacket can damage the magnetic surface.

6. Magnetic energy can destroy the data on your diskettes. Keep your diskettes

away from speakers, radios, television sets and other sources of magneticfields.


99/200

Users Manual 4-21

Operating Basics

OPERATINGBASICS

Using the microphoneYour computer has a built-in microphone that can be used to record monauralsounds into your applications. It can also be used to issue voice commands to

applications that support such functions.(Built-in microphone is provided withsome models)

Since your computer has a built-in microphone and speaker, feedback may beheard under certain conditions. Feedback occurs when sound from the speaker is

picked up in the microphone and amplified back to the speaker, which amplifiesit again to the microphone.

This feedback occurs repeatedly and causes a very loud, high-pitched noise. It isa common phenomenon that occurs in any sound system when the microphoneinput is output to the speaker (throughput) and the speaker volume is too loud ortoo close to the microphone. You can control throughput by adjusting the volumeof your speaker or through the Mute function in the Master Volume panel. Referto your Windows documentation for details on using the Master Volume panel.

Modem(provided with some models)This section describes how to connect and disconnect the internal modem to andfrom a telephone jack.

Note: The internal modem does not support voice functions. All dataand fax functions are supported.

CAUTIONS: 1. In case of a lightning storm, unplug the modem cablefrom the telephone jack.

2. Do not connect the modem to a digital telephone line. A

digital line will damage the modem.


100/200

Operating Basics

4-22 Users Manual

OPERATINGBASICS

Region selectionTelecommunication regulations vary from one region to another, so you willneed to make sure the internal modems settings are correct for the region inwhich it will be used.

To select a region, follow the steps below.

1. Click start, point to All Programs, point to TOSHIBA, point to Net-working and clickModem Region Select Utility.

Note:Do not use the Country/Region Select function in the Modemsetup utility in the Control Panel if the function is available. If youchange the Country/Region in the Control Panel, the change maynot take effect.

2. The Region Selection icon will appear in the Windows Task Bar.

Figure 4-10 The Region Selection icon (Windows VistaTM)

3. Click the icon with the primary mouse button to display a list of regions thatthe modem supports. A sub menu for telephony location information willalso be displayed. A check will appear next to the currently selected regionand telephony location.

4. Select a region from the region menu or a telephony location from the sub-menu.

When you click a region it becomes the modems region selection, andthe New Location for telephony will be set automatically.

When you select a telephony location, the corresponding region is auto-matically selected and it becomes the modems current region setting.


101/200

Users Manual 4-23

Operating Basics

OPERATINGBASICS

Properties menuClick the icon with the secondary mouse button to display the following menu.

Figure 4-11 The menu list (Windows VistaTM)

SettingYou can enable or disable the following settings:

AutoRun Mode

The Region Select utility starts automatically when you start up the operat-ing system.

Open the Dialing Properties dialog box after selecting region.

The dialing properties dialog box will be displayed automatically after you

select the region.Location list for region selection.

A submenu appears displaying location information for telephony.

Open dialog box, if the modem and Telephony Current

Location region code do not match.

A warning dialog box is displayed if current settings for region code andtelephony location are incorrect.

Modem Selection

If the computer cannot recognize the internal modem, a dialog box is displayed.Select the COM port for your modem to use.

Dialing Properties

Select this item to display the dialing properties.

CAUTION:If you are using the computer in Japan, the Telecommu-

nications Business Law requires that you select Japan region mode.It is illegal to use the modem in Japan with any other selection.


102/200

Operating Basics

4-24 Users Manual

OPERATINGBASICS

Connecting

To connect the internal modem cable, follow the steps below.

1. Plug one end of the modular cable into the modem jack.

2. Plug the other end of the modular cable into a telephone jack.

Figure 4-12 Connecting the internal modem

CAUTION:Do not pull on the cable or move the computer while thecable is connected.

Note:If you use a storage device such as a DVD-ROM drive, CD-RW/DVD-ROM drive or HDD connected to a 16-bit PC card, youmight experience the following modem problems:

1. Modem speed is slow or communication is interrupted.

2. Skips may occur in sound.

Disconnecting

To disconnect the internal modem cable, follow the steps below.

1. Pinch the lever on the connector in the telephone jack and pull out the con-nector.

2. Disconnect the cable from the computer in the same manner.

TELEPHONE

JACK

MODEM JACK


103/200

Users Manual 4-25

Operating Basics

OPERATINGBASICS

Wireless communicationsThe computers wireless communication function supports Wireless LAN only.

Wireless LANThe Wireless LAN is compatible with other LAN systems based on DirectSequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radiotechnology that complies with IEEE802.11 wireless LAN standard (Revision A,B or G).

Supported features. It supports the following features:

Automatic Transmit Rate Select mechanism in the transmit range of 54, 48,36, 24, 18, 12, 9 and 6 Mbit/s (Revision A and G, Revision B/G, A/B/G

combo type). Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5,

2 and 1 Mbit/s (Revision B).

Frequency Channel Selection (Revision A: 5 GHz, Revision B/G: 2.4GHz)

Roaming over multiple channels

Wired Equivalent Privacy (WEP) data encryption, based on the 128 bitencryption algorithm (Atheros module type).

Advanced Encryption Standard (AES) data encryption, based on 256 bitencryption algorithm (Atheros module type).

It may not be possible to make a network connection to a specified network nameusing the ad hoc network function. If this occurs, the new network(*) will have to

be configured for all computers connected to the same network in order to reen-able network connections.* Please be sure to use new network name.

Security

Be sure to enable WPA (encryption) function. Otherwise your computer willallow the illegal access by outsider through wireless LAN to cause illegalinstruction, eavesdropping, and loss or destruction of stored data. TOSHIBAstrongly recommends the customer to enable the WPA function.

TOSHIBA is not liable for the eavesdropping of data due to the use of Wire-less LAN and the damage thereof.


104/200

Operating Basics

4-26 Users Manual

OPERATINGBASICS

Wireless communication switch

You can enable or disable Wireless LAN functions, with the on/off switch. Notransmissions are sent or received when the switch is off. Slide the switch towardthe left of the computer to turn it on and toward the right of the computer to turn

it off.CAUTION: Set the switch to off in airplanes and hospitals. Checkthe indicator. It will stop glowing when the wireless communication

function is off.

Turn the computer off when you enter an airplane and check the carriers regula-tions before you use a computer on board.

Wireless communication Indicator

The wireless communication indicator indicates the status of the wireless com-munication functions.

If you used the Task Bar to disable Wireless LAN, restart the computer or followthe procedures below to enable the system to recognize Wireless LAN. ClickStart, open Control Panel, clickSystem and Maintenance, clickSys-tem, clickDevice Manager, double-clickNetwork Adapters, and rightclickthe wireless device then choose Enable.

Indicator status Indication

Indicator off Wireless communication switch is set to off.Automatic power down because of overheating.Power malfunction

Indicator glows Wireless communication switch is on.Wireless LAN is turned on by an application.


105/200

Users Manual 4-27

Operating Basics

OPERATINGBASICS

LANThe computer has built-in support for Ethernet LAN (10 megabits per second,10BASE-T) or Fast Ethernet LAN (100 megabits per second, 100BASE-TX).(depend on model you purchased) This section describes how to connect/disconnect to a LAN.

CAUTION:Do not install or remove an optional memory modulewhile Wake-up on LAN is enabled.

Note: The Wake-up on LAN function consumes power even when thesystem is off. Leave the AC adaptor connected while using this fea-ture.

Connecting LAN cableCAUTION: The computer must be configured properly before con-necting to a LAN. Logging onto a LAN using the computers default

settings could cause a malfunction in LAN operation. Check withyour LAN administrator regarding set-up procedures.

If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX),be sure to connect with a category 5 cable, CAT5, or higher.

If you are using Ethernet LAN (10 megabits per second, 10BASE-T), connectwith a category 3 cable, CAT3, or higher.

To connect the LAN cable, follow the steps below.

1. Turn off the power to the computer and to all external devices connected tothe computer.

2. Plug one end of the cable into the LAN jack. Press gently until you hear thelatch click into place.

Figure 4-13 Connecting the LAN cable

LAN JACK


106/200

Operating Basics

4-28 Users Manual

OPERATINGBASICS

3. Plug the other end of the cable into a LAN hub connector. Check with yourLAN administrator before connecting to a hub.

Disconnecting LAN cableTo disconnect the LAN cable, follow the steps below.

Note:Make sure theLAN active is out before you disconnect thecomputer from the LAN.

1. Pinch the lever on the connector in the computers LAN jack and pull outthe connector.

2. Disconnect the cable from the LAN hub in the same manner. Check withyour LAN administrator before disconnecting from the hub.

Cleaning the computerTo help ensure long, trouble-free operation, keep the computer free of dust anduse care with liquids around the computer.

Be careful not to spill liquids into the computer. If the computer does getwet, turn the power off immediately and let the computer dry completely

before you turn it on again.

Clean the computer using a slightly damp (with water) cloth. You can useglass cleaner on the display. Spray a small amount of cleaner on a soft, cleancloth and wipe the screen gently with the cloth.

CAUTION:Never spray cleaner directly onto the computer or letliquid run into any part of it. Never use harsh or caustic chemical

products to clean the computer.


107/200

Users Manual 4-29

Operating Basics

OPERATINGBASICS

Moving the computerThe computer is designed for rugged durability. However, a few simple precau-tions taken when moving the computer will help ensure trouble-free operation.

Make sure all disk activity has ended before moving the computer. Checkthe Disk indicator on the computer.

If a CD/DVD is in the drive, remove it. Also make sure the drawer issecurely closed.

Turn off the power to the computer.

Disconnect the AC adaptor and all peripherals before moving the computer.

Close the display. Do not pick up the computer by its display panel.

Close all port covers.

Use the carrying case when transporting the computer.

When carrying your computer, be sure to hold it securely so that it does notfall or hit anything.

Do not carry your computer by holding protruded portions.

Heat dispersal

To protect from overheating, the CPU has an internal temperature sensor. If thecomputers internal temperature rises to a certain level, the cooling fan is turnedon or the processing speed is lowered. You can select whether to control the CPUtemperature by turning on the fan first, then if necessary, lowering the CPUspeed. Or, by lowering the CPU speed first, then if necessary, turning on the fan.Use the Cooling Methoditem of theBasic Setup window in TOSHIBA PowerSaver.

When the CPU temperature falls to a normal range, the fan is turned off and theCPU operation returns to standard speed.

Note:If the CPU temperature reaches an unacceptably high levelwith either setting, the system automatically shuts down to preventdamage. Data in memory will be lost.


108/200

Users Manual 5-1

THEKEYBOARD

Chapter 5

The KeyboardThe computers keyboard layouts are compatible with a 101/102-key enhancedkeyboard. By pressing some keys in combination, all the 101/102-key keyboardfunctions can be executed on the computer.

The number of keys on your keyboard depends on which country/regions key-board layout your computer is configured with. Keyboards for numerous lan-

guages are available.There are five types of keys: typewriter keys, keypad overlay, function keys, softkeys and cursor control keys.

Typewriter keysThe typewriter keys, produce the upper- and lowercase letters, numbers, punctu-ation marks, and special symbols that appear on the screen.

There are some differences, however, between using a typewriter and using acomputer keyboard:

Letters and numbers produced in computer text vary in width. Spaces, whichare created by a space character, may also vary depending on line justifi-cation and other factors.

The lowercase l (el) and the number 1 (one) are not interchangeable on com-puters as they are on a typewriter.

The uppercase O (oh) and the 0 (zero) are not interchangeable.

The Caps Lock function key locks only the alphabetic characters in upper-case while the shift lock on a typewriter places all keys in the shifted posi-tion.

The Shift keys, the Tab key, and the BkSp (backspace) key perform thesame function as their typewriter counterparts but also have special com-

puter functions.


109/200

The Keyboard

5-2 Users Manual

THEKEYBOARD

F1 ... F12 function keysThe function keys, not to be confused with Fn, are the 12 keys at the top of yourkeyboard. These keys are dark gray, but function differently from the other dark

gray keys.

F1 through F12 are called function keys because they execute programmedfunctions when pressed. Used in combination with the Fn key, keys marked withicons execute specific functions on the computer. See the section, Soft keys: Fnkey combinations, in this chapter. The function executed by individual keysdepends on the software you are using.

Soft keys: Fn key combinationsThe Fn (function) is unique to Toshiba computers and is used in combinationwith other keys to form soft keys. Soft keys are key combinations that enable,disable or configure specific features.

Note: Some software may disable or interfere with soft-key opera-tions. Soft-key settings are not restored by the Resume feature.

Emulating keys on enhanced keyboardThe keyboard is designed to provide all the features of the 101-key enhancedkeyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has anumeric keypad and scroll lock key. It also has additional Enter, Ctrl and Altkeys to the right of the main keyboard. Since the keyboard is smaller and hasfewer keys, some of the enhanced keyboard functions must be simulated usingtwo keys instead of one on the larger keyboard.

Your software may require you to use keys that the keyboard does not have.Pressing the Fn key and one of the following keys simulates the enhanced key-

boards functions.

Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated,the keys with white markings on the bottom edge become numeric keypad keys(Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay sec-


110/200

Users Manual 5-3

The Keyboard

THEKEYBOARD

tion in this chapter for more information on how to operate these keys. Thepower on default for both settings is off.

Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power ondefault is off.

Press Fn + Enterto simulate Enteron the enhanced keyboards numeric key-

pad.

Press Fn + Ctrl to simulate the enhanced keyboards right Ctrl key.

Press Fn + Alt to simulate the enhanced keyboards right Alt key.

Hot keysHot keys (Fn + a function or Esc key) let you enable or disable certain featuresof the computers.

Sound mute: Pressing Fn + Esc in a Windows environment turns sound on oroff. When you press these hot keys, the current setting will be displayed as anicon.


111/200

The Keyboard

5-4 Users Manual

THEKEYBOARD

Instant security: Press Fn + F1 to enter "Lock computer" mode. To restor yourdesktop, you need to log on again.

Power Plan: Pressing Fn + F2 changes the power settings.

Sleep: Pressing Fn + F3 switches the system to Sleep mode.

Hibernation: Pressing Fn + F4 switches the system to Hibernate mode.

Output: Pressing Fn + F5 changes the active display device.


112/200


113/200

The Keyboard

5-6 Users Manual

THEKEYBOARD

TOSHIBA Zooming Utility (enlarge): Pressing Fn + 2 enlarges the icon sizeon the desktop or the font sizes within one of the supported application windows.


114/200

Users Manual 5-7

The Keyboard

THEKEYBOARD

Fn Sticky keyYou can use the Toshiba Accessibility Utility to make the Fn key sticky, that is,you can press it once, release it, and they press an F number key.

To start the Toshiba Accessibility Utility, click start, point to All Programs, pointto TOSHIBA, point to Utilities and click Accessibility.

Windows special keysThe keyboard provides two keys that have special functions in Windows: oneactivates the Start menu and the other has the same function as the secondarymouse button.

This key activates the Windows Start menu.

This key has the same function as the secondary mouse button.

Keypad overlayYour computers keyboard does not have an independent numeric keypad, but itsnumeric keypad overlay functions like one.

The keys in the center of the ke

Documents

A100 User Guide