phtruck.comphtruck.com/download/hvd/catalogs/IndividualDCV... · 6 3 pos. flow adjustment on C2 only A 3 pos. Detent C1, C2 and Center B Infinite position friction lock w/ center

Stackable, Load Sense Directional ControlsBulletin HY14-2101/US

bul 2101.p65, dd

Pulsar VPL Series (Non-compensated)

1 Parker Hannifin CorporationHydraulic Valve DivisionElyria, Ohio, USA

General Description

Stackable, Load Sense Directional Control Valve

The Pulsar VPL Series valve can be equipped formanual operation, hydraulic or electro-hydraulicremote control, or all three together. This flexibility ofconfiguration provides freedom in terms of componentlocation and plumbing arrangements.

The non-compensated valve is fully interchangeablewith today's compensated products. Combinationstacks are available combining VPL with VP/VPOSeries Products.

(Please consult factory for further details.)

Features/Benefits

• Interchangeable spools Allows for reduced inventory.

• Relief with anti-cavitation check Allows for shockand over pressure protection.

• Adjustable flow stops Provides greater control offlow.

• Three position detent and infinite friction lock Provides manual flow control.

• Integral load sense logic Better circuit efficiency.

• Intrinsically safe rating on solenoids May be appliedin certain hazardous environments.

• Internal pilot supply Reduces external plumbing.

Technical Information

Electrical Specifications

Standard & Marine Solenoids

Coil resistance 12 VDC - 28.0 ohms at 21°C (70°F)24 VDC - 65.0 ohms at 21°C (70°F)

Operating voltage 12±3 VDC; 24±3 VDC

Current draw 430 mA at 12 VDC and 21°C (70°F)370 mA at 24 VDC and 21° C (70°F)

PWM frequency 33 Hz

Connectors WeatherPack (std.); Hirschmann,Flying Leads

Intrinsic Safety Approvals

MSHA IA-627-0, IA-14238-0,XP Cert. No. 4111-0

CENELEC NEMKO 90.114 - Eex ib IIA, T4,

Imax = 300 mA, 12 VDC,

Leq = 2.25 mH, Ceq = 0

NEMKO 90.114 - Eex ib IIA, T4,

Imax = 250 mA, 9 VDC,

Leq = 2.25 mH, Ceq = 0

NEMKO 90.227 - Eex m II T4

CSA Class I, Groups C and D

SpecificationsOperating Pressure

Pressure supply port 350 Bar (5000 PSI)Cylinder ports 400 Bar (5800 PSI)Tank ports 14 Bar (200 PSI)

Maximum Inlet Flow 190 LPM (50 GPM)

Spool Flow Ratings 6, 10, 17, 34, 53, 98 LPM15 Bar (220 PSI) Drop (1.5, 2.5, 4.5, 9, 14, 26 GPM)

Spool/Cylinder Closed, Vented-open,Port Configuration Open (motor)

Spool Deadband 25% of stroke

Recommended Filtration SAE Class 5 (17/14-ISO 4406)

Fluid Temp. Range -40°C to 90°C (-40°F to 195°F)

Max. Fluid Temp. 121°C (250°F)

Ambient Temp. Range -40°C to 88°C (-40°F to 190°F)

Fluid Viscosity Range 323 to 1.1 cSt (1500 to 30 SUS)

Seal Material Nitrile

Mounting Attitude Unrestricted

Weight (approx.) 4.5 kg (10.0 lbs.) work segment

Step Response: 0%-100% 300 milliseconds100%-0% 150 milliseconds

Hydraulic Control (VWL) 24.1 Bar (350 PSI) PilotDeadband 5.5 Bar (80 PSI)Fullstroke 15.2Bar (220 PSI)

Hydraulic Control (VKL) 14.5 Bar (210 PSI) PilotDeadband 3.5 Bar (50 PSI)Fullstroke 10.3 Bar (150 PSI)

Handle Torque 0.6 - 2.5 Nm (5 - 22 lb/in)


bul 2101.p65, dd


Pulsar VPL Series (Non-compensated)Ordering Information

Code Description0 None (VWL, VKL, VML only)1 12 V Pulsar, 12” flying leads

3 12 V Pulsar with Weather Pack connector, 12” leads

5 24 V Pulsar, 12” flying leads7 24 V Pulsar with Weather Pack connector, 12” leads

A 12 V Marine (Nemko), 100” flying leads

B 24 V Marine (Nemko), 100” flying leadsJ 12 V Hirschmann, Large (DIN 43 - GDM Series)

K 24 V Hirschmann, Large (DIN 43 - GDM Series)

L 12 V Hirschmann, Small (G Series)M 24 V Hirschmann, Small (G Series)

N 12 V Pulsar with 36” flying leads

P 12 V Pulsar with 36” leads, Weather Pack connectorQ 24 V Pulsar with 36” flying leads

R 24 V Pulsar with 36” leads, Weather Pack connector

S 11.2 V, Intrinsically safe w/male Electro connectorT 11.2 V, Intrinsically safe w/Weather Pack connector

X 12 V, XP Pulsar with male Electro connector

Code Description2 2 way, C1 port

3 3 way, C1 port

4 4 way, C1 and C2 port

Code DescriptionQ Electrohydraulic

on-off

P Electrohydraulicproportional

K Hydraulic remote(210 PSI pilot)

W Hydraulic remote(350 PSI pilot)

M Manual Control

Code DescriptionA 5.6 LPM (1.5 GPM)

1 9.5 LPM (2.5 GPM)

2 17.0 LPM (4.5 GPM)3 34.0 LPM (9.0 GPM)

4 53.0 LPM (14.0 GPM)

5 98.5 LPM (26.0 GPM)

Note: For different flows ConsultFactory.

Code Description2 Closed cylinder ports (CC)3 C1 port (CC), C2 port (VOC)

4 Open cylinder ports (OC-Motor)

7 Vented open cylinder ports (VOC)

Code Description1 2 pos. flow adjustment on C1

2 2 pos. no flow adjustments3 3 pos. no flow adjustments

4 3 pos. flow adjustments on C1 and C2

5 3 pos. flow adjustment on C1 only6 3 pos. flow adjustment on C2 only

A 3 pos. Detent C1, C2 and Center

B Infinite position friction lock w/ center detent

Note: Detent not available w/ flow adjustment option(Code A & B are VML only)

Ordering Example:

VQL5444-3035-26JO

VValve Spool

OperationLow FlowSection

SpoolFlow

Rating

CylinderPort

Configuration

PilotControl

LSpool

PositionsFlow

Directions


bul 2101.p65, dd

Pulsar VPL Series (Non-compensated)


Ordering Information

Code Description0 Non-compensated

Code Description3 Manual operator shaft only

4 Manual operator with adapterand 6-inch handle

5 Manual adapter only6 Marine handle adapter

7 Marine handle adapter with6-inch handle

Code Description4 SAE ports5 BSPP ports

Code Description0 No port cavity

2 Relief, with anticavitation check

3 Anticavitation check5 Float, 12 VDC or 24 VDC

6 Defeat plug

Code Pressure SettingA 50 Bar (750 PSI)

B 63 Bar (950 PSI)

C 80 Bar 1150 PSI)D 100 Bar (1450 PSI)

F 125 Bar (1850 PSI)

G 140 Bar (2050 PSI)H 160 Bar (2350 PSI)

J 175 Bar (2550 PSI)

K 190 Bar (2750 PSI)L 210 Bar (3050 PSI)

M 230 Bar (3350 PSI)

N 250 Bar (3650 PSI)P 280 Bar (4050 PSI)

R 300 Bar (4350 PSI)

S 320 Bar (4650 PSI)T 350 Bar (5050 PSI)

O N/A

Code Description0 No port cavity

2 Relief, with anticavitation check

3 Anticavitation check5 Float, 12 VDC or 24 VDC

6 Defeat plug

0Section

PressureCompensator

ManualOverride

DesignLevel

C1CylinderPort Option

C2CylinderPort Option

C2 PressureC1 Pressure

Bulletin HY14-2101/US,3M, 9/02, PHD

Parker Hannifin CorporationHydraulic Valve Division520 Ternes AvenueElyria, Ohio, USA 44035Tel: (440) 366-5200Fax: (440) 366-5253www.parker.com/hydraulicvalve

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTYDAMAGE.

This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise.It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applicationsfor these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warningrequirements of the application are met.

The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any timewithout notice.

WARNING

Pressure Drop C1/C2 ➔➔➔➔➔ T(Meter Out Spools)

Segment Flow vs.Load Pressure

With Pressure Compensated Bypass Inlet (225 PSID)(Excess Flow can be limited with Spool Stroke Adjustment if required)

Note: The flow rates for all spools will increase by 2 to 3% for every 10 PSI increasein differential pressure drop from the pump supply port to the load sensing port.

All OptionsManual ControlVML

Ps

C2

L.S.

C1

T T

Relief with Anticavitation

Anticavitation Check

Digital PulsarDigital Pulsar

Flow AdjustmentScrews

Load Sense Shuttle NetworkInterchangeable Spools

6” Manual Operator

Hydraulic RemoteControl – VWL/VML

The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions statedin the "Offer of Sale".

Offer of Sale


Pulsar VPL Series (Non-compensated)Technical Information

Bulletin HY14-2101-B2/US

Series VPLProportional Valves

Effective: February 1, 2004Supersedes: Cat. No. PMF-1030 dated 3/98

Parker Hannifin CorporationHydraulic Valve DivisionElyria, Ohio, USA

��

Bulletin HY14-2101-B2/US Proportional ValveSeries VPL

Copyright 2004, Parker Hannifin Corporation, All Rights Reserved


This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It isimportant that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for theseproducts or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements ofthe application are met.

The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time withoutnotice.

WARNING

The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the "Offerof Sale".

Offer of Sale


�

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLContents

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte

Charlotte


�

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLIntroduction


�

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLSchematics

Examples

2. Sample load sensing circuit

1. Sample fixed displacement circuit


�

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLOperation

VPL - sectional drawing


�

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLSpecifications


�

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLActuation

SYMBOL DESCRIPTION


�

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLInlet Types

SYMBOL DESCRIPTION


Bulletin HY14-2101-B2/US Proportional ValveSeries VPLWork Segments

SYMBOL DESCRIPTION


Bulletin HY14-2101-B2/US Proportional ValveSeries VPLPort Options/Stacking Plate

SYMBOL DESCRIPTION

SYMBOL DESCRIPTION


��

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLSpool Types

SYMBOL DESCRIPTION

SpoolI.D. Code GPM L/min


��

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLPerformance Curves


��

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLPerformance Curves


��

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLDimensions

A(in/mm)

B(in/mm)

NUMBERS OFSEGMENTS


��

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLAssembly Specifications

WORK SEGMENT

3a. WORK PORT OPTION 3b. PRESSURE SETTING

6. HANDLE OPTIONS9. WORK PORT FORM

1. INLET

4. PILOT OPTION

5. SPOOL TYPE 2. SEGMENT OPTION

7. STACKING PLATE

8. TIE ROD LENGTH


��

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLAssembly Order Form

C1 C2 C1 C2 Relief Anticav Defeat Relief Anticav DefeatC2 PORT OPTION (3)C1 PORT OPTION (3)PRES. LIMITER (2)FLOW (5)SPOOL

TYPE (5)SEGMENTFUNCTION

SEGMENTPOSITION

SEGMENTPOSITION MANUAL REMOTE

VALVE ACTUATORELECTRIC

ON/OFF PROPNOTES AND / OR SPECIAL INSTRUCTIONS


��

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLOrdering Information


��

Bulletin HY14-2101-B2/US Proportional ValveSeries VPLOffer of Sale

The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorizeddistributors are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiaries and its authorized distributors. Thisoffer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order for any such items,when communicated to Parker Hannifin Corporation, its subsidiary or an authorized distributor (“Seller”) verbally or in writing, shall constitute acceptanceof this offer.

1. Terms and Conditions of Sale: All descriptions, quotations, proposals,offers, acknowledgments, acceptances and sales of Seller’s products aresubject to and shall be governed exclusively by the terms and conditionsstated herein. Buyer’s acceptance of any offer to sell is limited to theseterms and conditions. Any terms or conditions in addition to, or inconsistentwith those stated herein, proposed by Buyer in any acceptance of an offerby Seller, are hereby objected to. No such additional, different or inconsistentterms and conditions shall become part of the contract between Buyer andSeller unless expressly accepted in writing by Seller. Seller’s acceptanceof any offer to purchase by Buyer is expressly conditional upon Buyer’sassent to all the terms and conditions stated herein, including any termsin addition to, or inconsistent with those contained in Buyer’s offer,Acceptance of Seller’s products shall in all events constitute such assent.2. Payment: Payment shall be made by Buyer net 30 days from the dateof delivery of the items purchased hereunder. Amounts not timely paidshall bear interest at the maximum rate permitted by law for each monthor portion thereof that the Buyer is late in making payment. Any claims byBuyer for omissions or shortages in a shipment shall be waived unlessSeller receives notice thereof within 30 days after Buyer’s receipt of theshipment.3. Delivery: Unless otherwise provided on the face hereof, delivery shallbe made F.O.B. Seller’s plant. Regardless of the method of delivery,however, risk of loss shall pass to Buyer upon Seller’s delivery to a carrier.Any delivery dates shown are approximate only and Seller shall have noliability for any delays in delivery.4. Warranty: Seller warrants that the items sold hereunder shall be freefrom defects in material or workmanship for a period of 18 months fromdate of shipment from Parker Hannifin Corporation. THIS WARRANTYCOMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TOITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHERWARRANTY, GUARANTEE, OR REPRESENTATION OF ANY KINDWHATSOEVER. ALL OTHER WARRANTIES, INCLUDING BUT NOTLIMITED TO, MERCHANTABILITY AND FITNESS FOR PURPOSE,WHETHER EXPRESS, IMPLIED, OR ARISING BY OPERATION OFLAW, TRADE USAGE, OR COURSE OF DEALING ARE HEREBYDISCLAIMED. NOTWITHSTANDING THE FOREGOING, THERE ARENO WARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIREDWHOLLY OR PARTIALLY, TO BUYER’S DESIGNS ORSPECIFICATIONS.5. Limitation Of Remedy: SELLER’S LIABILITY ARISING FROM OR INANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACTSHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENTOF THE ITEMS SOLD OR REFUND OF THE PURCHASE PRICE PAIDBY BUYER, AT SELLER’S SOLE OPTION. IN NO EVENT SHALLSELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL ORSPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER,INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING FROMOR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR ITEMSSOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACHOF CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN TORT,INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TOWARN OR STRICT LIABILITY.6. Changes, Reschedules and Cancellations: Buyer may request tomodify the designs or specifications for the items sold hereunder as wellas the quantities and delivery dates thereof, or may request to cancel allor part of this order, however, no such requested modification or cancellationshall become part of the contract between Buyer and Seller unlessaccepted by Seller in a written amendment to this Agreement. Acceptanceof any such requested modification or cancellation shall be at Seller’sdiscretion, and shall be upon such terms and conditions as Seller mayrequire.7. Special Tooling: A tooling charge may be imposed for any specialtooling, including without limitation, dies, fixtures, molds and patterns,acquired to manufacture items sold pursuant to this contract. Such specialtooling shall be and remain Seller’s property notwithstanding payment ofany charges by Buyer. In no event will Buyer acquire any interest inapparatus belonging to Seller which is utilized in the manufacture of theitems sold hereunder, even if such apparatus has been specially convertedor adapted for such manufacture and notwithstanding any charges paid

by Buyer. Unless otherwise agreed, Seller shall have the right to alter,discard or otherwise dispose of any special tooling or other property in itssole discretion at any time.8. Buyer’s Property: Any designs, tools, patterns, materials, drawings,confidential information or equipment furnished by Buyer or any otheritems which become Buyer’s property, may be considered obsolete andmay be destroyed by Seller after two (2) consecutive years have elapsedwithout Buyer placing an order for the items which are manufactured usingsuch property, Seller shall not be responsible for any loss or damage tosuch property while it is in Seller’s possession or control.9. Taxes: Unless otherwise indicated on the face hereof, all prices andcharges are exclusive of excise, sales, use, property, occupational or liketaxes which may be imposed by any taxing authority upon the manufacture,sale or delivery of the items sold hereunder. If any such taxes must be paidby Seller or if Seller is liable for the collection of such tax, the amountthereof shall be in addition to the amounts for the items sold. Buyer agreesto pay all such taxes or to reimburse Seller therefore upon receipt of itsinvoice. If Buyer claims exemption from any sales, use or other taximposed by any taxing authority, Buyer shall save Seller harmless fromand against any such tax, together with any interest or penalties thereonwhich may be assessed if the items are held to be taxable.10. Indemnity For Infringement of Intellectual Property Rights: Sellershall have no liability for infringement of any patents, trademarks, copyrights,trade dress, trade secrets or similar rights except as provided in this Part10. Seller will defend and indemnify Buyer against allegations ofinfringement of U.S. Patents, U.S. Trademarks, copyrights, trade dressand trade secrets (hereinafter ‘Intellectual Property Rights’). Seller willdefend at its expense and will pay the cost of any settlement or damagesawarded in an action brought against Buyer based on an allegation thatan item sold pursuant to this contract infringes the Intellectual PropertyRights of a third party. Seller’s obligation to defend and indemnify Buyeris contingent on Buyer notifying Seller within ten (10) days after Buyerbecomes aware of such allegations of infringement, and Seller having solecontrol over the defense of any allegations or actions including allnegotiations for settlement or compromise. If an item sold hereunder issubject to a claim that it infringes the Intellectual Property Rights of a thirdparty, Seller may, at its sole expense and option, procure for Buyer theright to continue using said item, replace or modify said item so as to makeit noninfringing, or offer to accept return of said item and return thepurchase price less a reasonable allowance for depreciation.Notwithstanding the foregoing, Seller shall have no liability for claims ofinfringement based on information provided by Buyer, or directed to itemsdelivered hereunder for which the designs are specified in whole or partby Buyer, or infringements resulting from the modification, combination oruse in a system of any item sold hereunder. The foregoing provisions ofthis Part 10 shall constitute Seller’s sole and exclusive liability and Buyer’ssole and exclusive remedy for infringement of Intellectual Property Rights.If a claim is based on information provided by Buyer or if the design for anitem delivered hereunder is specified in whole or in part by Buyer, Buyershall defend and indemnify Seller for all costs, expenses or judgmentsresulting from any claim that such item infringes any patent, trademark,copyright, trade dress, trade secret or any similar right.11. Force Majeure: Seller does not assume the risk of and shall not beliable for delay or failure to perform any of Seller’s obligations by reasonof circumstances beyond the reasonable control of Seller (hereinafter‘Events of Force Majeure’). Events of Force Majeure shall include withoutlimitation, accidents, acts of God, strikes or labor disputes, acts, laws,rules or regulations of any government or government agency, fires,floods, delays or failures in delivery of carriers or suppliers, shortages ofmaterials and any other cause beyond Seller’s control.12. Entire Agreement/Governing Law: The terms and conditions setforth herein, together with any amendments, modifications and anydifferent terms or conditions expressly accepted by Seller in writing, shallconstitute the entire Agreement concerning the items sold, and there areno oral or other representations or agreements which pertain thereto. ThisAgreement shall be governed in all respects by the law of the State of Ohio.No actions arising out of the sale of the items sold hereunder or thisAgreement may be brought by either party more than two (2) years afterthe cause of action accrues.

9/91-P

Bulletin HY14-2101-B2/US,3C, 3/04, PHD


WHEN IT COMES TOADVANCED HYDRAULIC TECHNOLOGY,

YOU’VE COMETO THE RIGHT PLACE

� ��

��

�� !��"�� #

��$� ��%��&��'

(�)��*��*��#

��$��

��$��

!�� '

+�� %�� ,��

!�� "��

!��$��

�� "��$

��!!��#��$�� "

�� "��!��#

�� '��#

�� %�� !��

�� '

��"��) ��

��!�� "�$��

�� "��!��

��!��"�%��

&�� '��

�� "�%��&�� $

�� "� ��

��

��'

�� )��

�*��%��&��) �!��

�� "��

%��&�� *��

� ��

PULSAR® VP/VPO SERIES VALVE FROM PARKER HANNIFIN

COMBINING BRAINS AND BRACOMBINING BRAINS AND BRACOMBINING BRAINS AND BRACOMBINING BRAINS AND BRACOMBINING BRAINS AND BRAWNWNWNWNWNFOR ACCURACYFOR ACCURACYFOR ACCURACYFOR ACCURACYFOR ACCURACY, FLEXIBILITY AND ECONOMY, FLEXIBILITY AND ECONOMY, FLEXIBILITY AND ECONOMY, FLEXIBILITY AND ECONOMY, FLEXIBILITY AND ECONOMY

HIGH ACCURACYHIGH ACCURACYHIGH ACCURACYHIGH ACCURACYHIGH ACCURACY, LOW COST, LOW COST, LOW COST, LOW COST, LOW COSTMAKE THE PULSARMAKE THE PULSARMAKE THE PULSARMAKE THE PULSARMAKE THE PULSAR®®®®® VP/VPO VP/VPO VP/VPO VP/VPO VP/VPO

SERIES YOUR VSERIES YOUR VSERIES YOUR VSERIES YOUR VSERIES YOUR VALALALALALVE OF CHOICEVE OF CHOICEVE OF CHOICEVE OF CHOICEVE OF CHOICE

Digital pilot stage dramatically lowersboth hysteresis and cost.

Bulletin HY14-2102/US,3C, 3/04, PHD


WHEN IT COMES TOWHEN IT COMES TOWHEN IT COMES TOWHEN IT COMES TOWHEN IT COMES TOADVADVADVADVADVANCED HYDRAULIC TECHNOLOGYANCED HYDRAULIC TECHNOLOGYANCED HYDRAULIC TECHNOLOGYANCED HYDRAULIC TECHNOLOGYANCED HYDRAULIC TECHNOLOGY,,,,,

YOU’VE COMEYOU’VE COMEYOU’VE COMEYOU’VE COMEYOU’VE COMETO THE RIGHT PLACETO THE RIGHT PLACETO THE RIGHT PLACETO THE RIGHT PLACETO THE RIGHT PLACE

As manufacturers around theworld look for innovative solutionsin hydraulic power, they increas-ingly look to Parker Hannifin.We’ve become a leader in combin-ing electronic control and hydraulictechnologies for a wide variety ofproducts.

Our family of Pulsar® controlproducts, either as valves orpackaged with electronics andsensors as systems, are findingwide application in off-highway,industrial, municipal and automo-tive markets. And more innova-tions in Pulsar valve products areon the way.

In fact, where there’s a need formore precise control, greaterversatility, improved safety andmore efficient operation, ParkerHannifin has the solution. As aresult, Parker Hannifin is makingwork easier, safer and moreeconomical for end users aroundthe world.

If you’d like more informationabout Parker Hannifin’s productsor services, contact your localParker Hannifin distributor or callus as 440-366-5200.


This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It isimportant that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for theseproducts or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements ofthe application are met.

The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time withoutnotice.

WARNING

The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the "Offerof Sale".

Offer of Sale

Copyright 2004, Parker Hannifin Corporation, All Rights Reserved

PULSAR® VP/VPO SERIES VALVE FROM PARKER HANNIFIN

Documents

phtruck.comphtruck.com/download/hvd/catalogs/IndividualDCV... · 6 3 pos. flow adjustment on C2 only A 3 pos. Detent C1, C2 and Center B Infinite position friction lock w/ center