Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
3A1322BENG
Parts
45:1 RAM Supply UnitFor dispensing high viscosity material at 45:1 ratio. For professional use only.
Not approved to European explosive atmospheres requirements.
Part No. 24E191
4500 psi (31 MPa, 310 bar) Maximum Fluid Working Pressure100 psi (0.7 MPa, 7 bar) Maximum Air Working Pressure140°F (60°C) Maximum Fluid Working Temperature
Important Safety InstructionsRead all warnings and instructions in all supplied manuals. Save all instructions.
24e191_3A1322_5b
Related Manuals
2 3A1322B
ContentsRelated Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 10Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 10
Related ManualsComponent manuals in English. Manuals are available at www.graco.com.
Part Description
313527 RAM Instructions - Parts
311828 Dura-Flo Pumps Instructions - Parts
Parts
3A1322B 3
Parts24E191
24e191_3A1322_1b
138
139
146,
152
14
102See Detail B
See Detail D
See Detail A
6
116
181, 180
115, 114, 113
101
146, to SOL 148 B
146, to SOL 148 A
Air InPressure
Switch
SOL 148 B
SOL 148 ASOL 147 A
Connect plate blow-off air line. Route along air motor hose.
With the air motor in the “full” down position, locate proximity switch (124) so that the probe is centered on the side of the coupling nut cover. Probe should be 0.157 in. (4 mm) max from cover.
Connect wire to terminal 1001 inside the junction box.
Schematic to be used for wiring receptacle (126) to limit switch (117).
Use electrical tape (180) to secure both ends of protective sleeve.
6
10
11
12
14
SOL 147 A
103
Parts
4 3A1322B
24e191_3A1322_1b
See Detail C
See Detail E
149
153
Ref 146
158
159
155156
6
157
151
150
Detail A
152
Connect plate blow-off air line. Route along air motor hose.
With the air motor in the “full” down position, locate proximity switch (124) so that the probe is centered on the side of the coupling nut cover. Probe should be 0.157 in. (4 mm) max from cover.
Connect wire to terminal 1001 inside the junction box.
Schematic to be used for wiring receptacle (126) to limit switch (117).
Use electrical tape (180) to secure both ends of protective sleeve.
6
10
11
12
14
Parts
3A1322B 5
PIN-1
PIN-3
PIN-5
PIN-2
PIN-4 4 3
2 1
PB122PB119 PB124
LT110
G A
LT148
G
LT141LT134 LT106
PB151
SS154GRACO
PS108AIR PRESSURE
ON
LS117EMPTY
LIMIT SWITCH
LS112RAM READY
LIMIT SWITCH
LS114LOW LEVEL LIMIT SWITCH
SOL139DEPRESSURIZE
PUMP
PX127PROX. SWITCH
PUMP1
PX129PROX. SWITCH
PUMP2
SOL147PUMP
ACTIVE
LEFT SIDE FRONT RIGHT SIDE
LOW
EMPTY
24e191_3A1322_2b
Detail CDetail B
127 126
147
117 12
119
118
118
129
Proximity Switch Mounting
130
120
123
124125
122,121
121, 122
136, 137
133
143
Connect plate blow-off air line. Route along air motor hose.
With the air motor in the “full” down position, locate proximity switch (124) so that the probe is centered on the side of the coupling nut cover. Probe should be 0.157 in. (4 mm) max from cover.
Connect wire to terminal 1001 inside the junction box.
Schematic to be used for wiring receptacle (126) to limit switch (117).
Use electrical tape (180) to secure both ends of protective sleeve.
6
10
11
12
14
RAM Up/Down and PLC Enclosure Mounting
11
12
10
12
(to pump junction box)
Parts
6 3A1322B
24e191_3A1322_3b
176174
175
174
173
172 171 170
172
177
Ref 159
Detail EDetail D Rear View of Air Controls
6
Connect plate blow-off air line. Route along air motor hose.
With the air motor in the “full” down position, locate proximity switch (124) so that the probe is centered on the side of the coupling nut cover. Probe should be 0.157 in. (4 mm) max from cover.
Connect wire to terminal 1001 inside the junction box.
Schematic to be used for wiring receptacle (126) to limit switch (117).
Use electrical tape (180) to secure both ends of protective sleeve.
6
10
11
12
14
Parts
3A1322B 7
Ref. No. Part No. Description
Qty.
101 249343 KIT, accessory, plc interface 1102 24E381 PUMP, 55gal, Dura-Flo, 6500/430 1103 C32463 CLAMP, saddle assembly 2113 100133 WASHER, lock, 3/8 8114 C32424 BOLT, u, 7" 4115 100307 NUT, hex 8116 16D898 BRACKET, limit sw, Dura-Flo, 6.5"
ram1
117 C07560 SWITCH, limit w/ arm 2118 C19197 WASHER, plain 8119 551787 SCREW, cap, 10, ss, but hd 4120 617337 COLLAR, clamp 2121 C19209 WASHER, lock 4122 C19800 SCREW, cap, socket hd 4123 617338 BRACKET, mounting 1124 517455 SWITCH, 18 mm proximity 1125 C56572 CABLE 1126 C07431 CONNECTOR, sealed 2127 C07435 CONNECTOR, sealed 2129 15H687 HOUSING, coupling nut 1130 119417 SCREW, set, allen, 1/4-20 x 5/8 1133 195356 KIT, accessory 1136 100020 WASHER, lock 2137 104472 SCREW, cap 2138 104632 VALVE, piloted 1139 597151 FITTING, elbow 1143 15H686 BRACKET, limit switch 1146 C12509 TUBE, nylon, rnd 50147 C20715 FITTING, locknut, conduit 2149 918537 APPLICATOR, ball seat, 1/2 port,
60:11
150 C20487 FITTING, nipple, hex 1151 15M834 FITTING, pipe, cross 1152 157191 FITTING, adapter (1/2npt x 3/4npt) 2153 C19391 FITTING, elbow 2155 C19681 BUSHING, pipe 1156 15M867 VALVE, check 1157 C20350 FITTING, elbow 90 deg 1158 156684 FITTING, union, adapter 1159 255682 HOSE, coupled, hp, 2.33 1170 94/0758/9
9FITTING, npl, hex, 1" x 3/4npt, mm, ms, 2k
1
171 C19661 BUSHING, reducing 1172 C38324 FITTING, elbow, street 2173 521850 VALVE, check 1174 C20490 FITTING, nipple, hex 3175 521975 FITTING, union, pipe 1176 C19491 FITTING, tee, 1-1/4 npt(f) 1177 C19660 FITTING, 1-1/4x1/2 1180 070182 TAPE, electrical 1181 C19802 SCREW, cap, socket hd 4182 100016 WASHER, lock 4
Ref. No. Part No. Description
Qty.
Parts
8 3A1322B
24E381
6500/430 55 Gallon Dura-Flo Pump
24e381_3A1322_1b
203
5
Apply sealant.
Tighten nut below tie bar until the lockwasher is flat, not to exceed 25 ft-lb, then tighten nut above tie bar.
5
7
205
202
206
204210
208
75
5
Detail
Ref. No. Part No. Description Qty.202 255688 RAM, 6.5 in., with air controls 1203 P45LSS PUMP, Dura-Flo, 6500/290 1204 255319 PLATE, wiper, 55 gallon, epdm 1205 255315 KIT, mounting, 6 in.,
55 gallon1
206 255392 KIT, mounting, lower 1208 103347 VALVE, safety, 100 psi 1210 190166 CYLINDER, intake 1
Technical Data
3A1322B 9
Technical DataMaximum Fluid Working Pressure. . . . . . . . . . . . . . . . . 4500 psi (31 MPa, 310 bar)
Maximum Air Working Pressure . . . . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar)
Maximum Fluid Temperature. . . . . . . . . . . . . . . . . . . . . 140°F (60°C)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650 lb (295 kg)
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A1322
Graco Headquarters: MinneapolisInternational Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2010, Graco Inc. is registered to ISO 9001www.graco.com
Revision B, February 2017
Graco Standard WarrantyGraco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERSThe Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco InformationSealant and Adhesive Dispensing Equipment
For the latest information about Graco products, visit www.graco.com.For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor, go to www.graco.com and select “Where to Buy” in the top blue bar, or call to find the nearest distributor.
If calling from the US: 800-746-1334If calling from outside the US: 0-1-330-966-3000