Upload
pakcik-kamal
View
192
Download
29
Embed Size (px)
DESCRIPTION
2g
Citation preview
Parameter BaselineTableParameterParameter Long
NameBaselineRemarkGloAcAMRDNRATEACSWCHSwitch of AMR Traffic
Re-admission after AMR Rate Decrease1GloAcTTRUEQFORCEDMaximum Time
in the True Queue when Service be Forced into
Queue(s)6GloAcFORCQUESWIAMRForced Queue Switch for AMR
Service1GloAcFORCQUESWICS64Forced Queue Switch for CS 64kbps
service1GloAcTTRUEQTime of True Queue for Congested Service in RAB
Setup Process(s)10GloAcQLENGTHTrue Queue
Length16GloAcTTRUEQRELOCTime of True Queue for Congested Service
Relocating into UTRAN(s)4HspaRNCFDPCHSUPINDRNC F-DPCH Support
Indicator1HspaDCHSDSCHSPTINDDual-Cell HS-DSCH Support
Indication1HspaRNCMIMO64QAMINDRNC MIMO and DL64QAM Combined
Capability Support Indicator0HspaRNCEFDPCHSUPINDRNC Enhanced F-DPCH
Support Indicator0HspaPOEHICHNOSERRL2Power Offset Relative to
E-HICH in Single Link Condition for E-HICH of Non-serving RLS in
Macro Diversity Condition (2ms TTI)(dB)5.0In document, default
value is 8.0. Should revisit?HspaHSGBRLIMITSWISwitch for Limiting
HSDPA GBR Resource Consumption0HspaCODEREASSPRDDPCH Code Re-Assign
Period(s)10HspaRNCMIMOINDRNC MIMO Support
Indicator1HspaPOERGCHSERRLS2Power Offset Relative to E-RGCH in
Single Link Condition for E-RGCH of Serving RLS in Macro Diversity
Condition (2ms TTI)(dB)0.0HspaRNCENL2INDRNC Downlink Enhanced Layer
2 Support Indicator1HspaRNC64QAMINDRNC 64QAM Support
Indicator1HspaPOERGCHSERRLS10Power Offset Relative to E-RGCH in
Single Link Condition for E-RGCH of Serving RLS in Macro Diversity
Condition (10ms TTI)(dB)0.0HspaNRTDTXDRXSWCHDTX/DRX Switch for
NRT0HspaRNCDCMIMOSUPINDRNC DC+MIMO Support
Indicator0HspaPOEHICHSERRLS2Power Offset Relative to E-HICH in
Single Link Condition for E-HICH of Serving RLS in Macro Diversity
Condition (2ms TTI)(dB)5.0In document, default value is 7.0. Should
revisit?HspaCODEREASSINDDPCH Code Re-Assign Support
Indicator0Should we enable?HspaEAGCHPOUPTSWCHDynamic Updating
Switch of E-AGCH Power Offset0HspaNVHSSCLESSSWCHHS-SCCH Less Switch
for Non-VoIP/AMR0HspaPOERGCHNONSERRLSPower Offset Relative to 10ms
TTI E-RGCH in Single Link Condition for E-RGCH of Non-serving RLS
in Macro Diversity Condition(dB)3.0In document, default value is
6.0. Should revisit?HspaPOEHICHSERRLS10Power Offset Relative to
E-HICH in Single Link Condition for E-HICH of Serving RLS in Macro
Diversity Condition (10ms TTI)(dB)0.0In document, default value is
7.0. Should revisit?HspaRTDTXDRXSWCHDTX/DRX Switch for
Speech0HspaRLCSIZESUPTTYPESupport Type of Downlink RLC Flexible PDU
Size Format2HspaHSSCLESSSWCHHS-SCCH Less
Switch0HspaULRLCSIZESPTTYPESupport Type of Uplink RLC Flexible PDU
Size Format3Should set to 2?HspaDTXDRXSWCHDTX/DRX
Switch0HspaPOEHICHNOSERRL10Power Offset Relative to E-HICH in
Single Link Condition for E-HICH of Non-serving RLS in Macro
Diversity Condition (10ms TTI)(dB)8.0QosSegMAXDLDPCHPOPower Offset
of the Maximum Downlink DPCH Showing Different Basic
Priority(dB)[[email protected]@[email protected]@[email protected]@[email protected]@[email protected]@[email protected]@[email protected]@[email protected]]QosSegBPSEGNUMBasic
Priority Segment Number5QosSegDLRATEADJLEVDownlink Rate Adjustment
Level(kbps)[8@64@128@384]QosSegBPTHRESHBasic Priority Segment
Threshold[3@6@9@11]QosSegDLRATEADJLEVNUMDownlink Rate Adjustment
Level Number4QosSegULRATEADJLEVNUMUplink Rate Adjustment Level
Number3Should modify to 4?QosSegARPSEGNUMARP Segment
Number3QosSegHSPAEQUHSUSEREquivalent HSPA
Users[[email protected]@[email protected]@[email protected]@[email protected]@[email protected]@[email protected]@[email protected]@[email protected]]QosSegEDCHNORMBITRATEE-DCH
Uplink Nominal Bit
Rate(kbps)[12@12@12@12@12@24@24@24@24@24@24@96@96@96@96@96]QosSegARPTHRESHARP
Segment Threshold[5@10]QosSegHSNORMBITRATEHS-DSCH Downlink Nominal
Bit
Rate(kbps)[12@12@12@12@12@24@24@24@24@24@24@96@96@96@96@96]QosSegULRATEADJLEVUplink
Rate Adjustment Level(kbps)[16@64@384]Should modify to
[16@64@128@384]?QosSegTHPSEGNUMTHP Segment
Number3QosSegDLNORMBITRATEDCH Downlink Nominal Bit
Rate(kbps)[8@8@8@8@8@16@16@16@16@16@16@64@64@64@64@64]QosSegULNORMBITRATEDCH
Uplink Nominal Bit
Rate(kbps)[8@8@8@8@8@16@16@16@16@16@16@64@64@64@64@64]QosSegTHPTHRESHTHP
Segment Threshold[5@10]QosSegMAXULDPCHPOPower Offset of the Maximum
Uplink DPCH Showing Different Basic
Priority(dB)[[email protected]@[email protected]@[email protected]@[email protected]@[email protected]@[email protected]@[email protected]@[email protected]]cnInfoATTINDCSIMSI
Attach and Detach Indicator1cnInfoNMOPSNetwork Mode of
Operation1cnInfoCNDOMAINCN Domain Supported2cnInfoKPSPS Domain DRX
Cycle Length Coefficient6cnInfoKCSCS Domain DRX Cycle Length
Coefficient6cnInfoT3212CSTimer for Periodic Location
Update(T3212)(hour)1.0Should synchronize 2G and 3G? Currently 2G
set to 4 hourscnInfoMBMSMODPRDCOEFFModification Period Coefficient
for MBMS7drbcSRBONEDCHSWCHSwitch of supporting SRB on E-DCH1Not
used (requires F-DPCH)drbcAMROVERHSPASWCHSwitch of CS voice over
HSPA0drbcTOFTIMESTHREvent 4B Counter Threshold for Cell_Dch to
Cell_FACH1drbcDELTANUME4B0THDIncrement Times of Event 4B0 for UE
Which is Not Sensitive for Battery Consumption Transferred to
URA_PCH or Idle State3drbcDTCPEBTHDEvent B Counter Threshold for
Restriction PS Increasing Rate on DL DCH or Triggering DL AMR
Increasing Rate Based on D-TCP2drbcINITIALRATEULInitial Rate of UL
DCH(kbps)16drbcDLPSRATELMTHIGHCNRT PS Traffic Downlink Rate Upper
Limit When High Rate C Traffic + PS
Traffic(kbps)64drbcDCHE4BTHDEvent 4B Counter Threshold for
Decreasing Rate on DCH4drbcSCHQSWCHHS/D->D/D or HS/E->D/D
Based on Quality Measurement Switch for S
Traffic0drbcPCHHOLDTIMETHRTime Threshold for CELL_PCH or URA_PCH to
Idle120Currently URA PCH is disableddrbcPCHSWCHSwitch of
URA_PCH/CELL_PCH Support0drbcDLPSRATELMTLOWCNRT PS Traffic Downlink
Rate Upper Limit When Low Rate C Traffic + PS
Traffic(kbps)128drbcFACHSWCHSwitch of Transferring to
CELL_FACH1drbcFTOPCHTHDEvent 4B Counter Threshold for CELL_FACH
without DRX to PCH Shared by Uplink and Downlink1drbcDTOPCHTHDEvent
4B Counter Threshold for CELL_DCH to PCH Shared by Uplink and
Downlink3drbcULPWRDASFSwitch for UL DCH Rate Adjustment Based on UE
Transmission Power1drbcDRBCSWCHDRBC Method
Switch3drbcETTITRAFFVOLSWCHSwitch of E-TTI Switching Triggered by
User Plane Throughput Measurement1drbcFTOIDLETHDEvent 4B Counter
Threshold for CELL_FACH without DRX to Idle Shared by Uplink and
Downlink2drbcDTCPEATHDEvent A Counter Threshold for PS on DL DCH or
DL AMR Decreasing Rate on D-TCP2drbcULPSRATELMTHIGHCNRT PS Traffic
Uplink Rate Upper Limit When High Rate C Traffic + PS
Traffic(kbps)64drbcULPSRATELMTLOWCNRT PS Traffic Uplink Rate Upper
Limit When Low Rate C Traffic + PS Traffic(kbps)128drbcCRATETHRDC
Traffic Rate Threshold Used for Determining NRT PS Rate Upper
Limit(kbps)32drbcETTIEBTHDEvent 4B Counter Threshold for E-TTI
Switching from 2ms to 10ms2drbcETTIEATHDEvent 4A Counter Threshold
for E-TTI Switching from 10ms to 2ms2drbcDCHADJRATESWCHSwitch for
DCH Rate Adjustment Based on Traffic Volume
Measurement1drbcDLPWRDASFSwitch for DL DCH Rate Adjustment Based on
D-TCP1drbcFACHE4ATHDEvent 4A Counter Threshold for CELL_FACH to
CELL_DCH Shared by Uplink and Downlink1drbcIBCHQSWCHHS/D->D/D or
HS/E->D/D Based on Quality Measurement Switch for I/B
Traffic0drbcINITIALRATEDLInitial Rate of DL
DCH(kbps)8drbcRFACHDownlink Maximum Rate Threshold of I/B Service
on CELL_FACH(kbps)8drbcDCHE4ATHDEvent 4A Counter Threshold for
Increasing Rate on DCH or DCH->HSPA2drbcDXHSBO0E4BTHDEvent 4B
Counter Threshold for HSPA Using DTX/DRX or CELL_FACH using DRX to
PCH or IDLE Shared by Uplink and Downlink10drbcRRACHUplink Maximum
Rate Threshold of I/B Service on RACH(kbps)8drbcDCHSIG68SWCHSwitch
of 6.8kbps Signaling Using on DCH0drbcCCHQSWCHQuality Measurement
Switch for VoIP/ CS Voice1drbcDTOIDLETHDEvent 4B Counter Threshold
for CELL_DCH to Idle Shared by Uplink and
Downlink3iuCnstNREPEATRESRSTMaximum Number of Retransmissions of
the RESOURCE RESET Message3iuCnstTRAFCMaximum Waiting Time for
RESET in RNC(s)8iuCnstTRELOCOVERALLSRNC Overall Protective Time for
Relocation(100ms)80iuCnstTIGORTimer for Ignoring all OVERLOAD
Messages or Signalling Point Congested
Information(TigOR)(s)60iuCnstTINTRTimer for Not Allowing to
Increase Traffic(TinTR)(s)100iuCnstTRESETDELAYTimer for Sending
RESOURCE RESET Response to CN(100ms)80iuCnstNREPEATRSTMaximum
Number of Retransmissions of the RESET Message3iuCnstTRELOCPREPSRNC
Wait Time for Relocation Preparation(100ms)60iuCnstTRESETWAITTimer
for RESOURCE RESET Response from CN(100ms)50iuCnstTDATAFWDMaximum
Time for Forwarding GTP-PDU Data in SRNC(100ms)50iuCnstTRATCTimer
Before Sending RESET Response to CN(s)18iuCnstTQUEUINGMaximum Time
for RAB Queuing in RNC(100ms)50rncBRncACKNACKENCINDHSDPA HS-DPCCH
ACK/NACK enhancement Support Indicator0Should
enable?rncBRncLCSMETHODLCS Support Method0rncBRncCS64RBMODESWCHCS
64K RB Mode Switch1rncBRncNBRCELLMONSUPINDNeighbouring Cell
Monitoring Support Indicator1rncBRncNACCSUPPINDNACC Support
Indicator0rncBRncBASEDIMSIHOINDHandover Based on IMSI Support
Indicator0rncBRncPSINTERSYSHOSUPPPS Inter-System Handover
Indicator0rncBRncPSCONVTRASUPPS Conversational RAB for VoIP Support
Indicator0rncBRncLDBSDINTSYSHOINDLoading based InterSys HO Support
Indicator0Should enable?rncBRncWAMRSUPINDWB-AMR Speech Support
Indicator0Require to open for WB AMR trialrncBRncFOURECHALLOWEDFour
E-DPDCHs Allowed Indicator0Require to open for HSUPA
5.76MbpsrncBRncPSSIGFORIMSINDPS Signalling RAB for IMS Support
Indicator0rncBRncPTPOVERHSMBMS PTP over HSDPA Support
Indicator0rncBRncDTMSUPPINDInter-System DTM Support Indicator0Only
valid when PSINTERSYSHOSUPP = 1rncBRncSERVBASEDHOINDService-Based
Handover Support Indicator0rncBRncR99NRTETRAHOSWCHR99 NRT Inter
Rat(EUTRAN) Handover Switch1rncBRncHSUPARATHOSWCHHSDPA Inter Rat
Handover Switch0Should enable?rncBRncR99NRTIFHOSWCHR99 NRT Inter
Frequency Handover Switch1rncBRncGRESPARA18Global Reserved
Parameter 181Require parameter descriptionrncBRncGRESPARA19Global
Reserved Parameter 1930Require parameter
descriptionrncBRncFASTRECFGSPTINDFast Reconfiguration Support
Indication1rncBRncGRESPARA9Global Reserved Parameter 9240Require
parameter descriptionrncBRncR99RTEUTRAHOSWCHR99 RT Inter
Rat(EUTRAN) Handover Switch1rncBRncHSDPARATHOSWCHHSDPA Inter Rat
Handover Switch1Should enable?rncBRncAMRIFHOSWCHAMR Inter Frequency
Handover Switch1rncBRncGRESPARA20Global Reserved Parameter
200Require parameter descriptionrncBRncAMRRATHOSWCHAMR Inter Rat
Handover Switch1rncBRncHSUPAEUTRAHOSWCHHSUPA Inter Rat(EUTRAN)
Handover Switch1rncBRncHSDPAIFHOSWCHHSDPA Inter Frequency Handover
Switch1rncBRncR99RTIFHOSWCHR99 RT Inter Frequency Handover
Switch1rncBRncHSUPAIFHOSWCHHSDPA Inter Frequency Handover
Switch1rncBRncDYNAUPDTPO2STCHDynamic Update PO2
Switch0rncBRncR99RTRATHOSWCHR99 RT Inter Rat Handover
Switch1rncBRncGRESPARA11Global Reserved Parameter 110Require
parameter descriptionrncBRncGRESPARA5Global Reserved Parameter
50Require parameter descriptionrncBRncGRESPARA10Global Reserved
Parameter 100Require parameter descriptionrncBRncGRESPARA6Global
Reserved Parameter 680Require parameter
descriptionrncBRncGRESPARA13Global Reserved Parameter 130Require
parameter descriptionrncBRncR99NRTRATHOSWCHR99 NRT Inter Rat
Handover Switch1Require parameter descriptionrncBRncGRESPARA7Global
Reserved Parameter 70Require parameter
descriptionrncBRncGRESPARA12Global Reserved Parameter 120Require
parameter descriptionrncBRncGRESPARA8Global Reserved Parameter
80Require parameter descriptionrncBRncGRESPARA15Global Reserved
Parameter 15480Require parameter descriptionrncBRncGRESPARA1Global
Reserved Parameter 120Require parameter
descriptionrncBRncGRESPARA14Global Reserved Parameter 140Require
parameter descriptionrncBRncGRESPARA2Global Reserved Parameter
20Require parameter descriptionrncBRncGRESPARA17Global Reserved
Parameter 170Require parameter descriptionrncBRncGRESPARA3Global
Reserved Parameter 30Require parameter
descriptionrncBRncGRESPARA16Global Reserved Parameter 16160Require
parameter descriptionrncBRncGRESPARA4Global Reserved Parameter
40Require parameter descriptionrncBRncHSDPAEUTRAHOSWCHHSDPA Inter
Rat(EUTRAN) Handover Switch1rncFunctionMBMSRATESWITCHMBMS Channel
Rate Support Indicator0rncFunctionEMGCALLRDTSWITCHEmergency Call
Redirect Switch0rncFunctionSHAREDNETMODEShared Network
Mode255rncFunctionPSNRIBITNUMNetwork Resource Identifier Bit Num in
PS Domain3rncFunctionCSNRIBITNUMNetwork Resource Identifier Bit Num
in CS Domain4rncFunctionLOCMODESWCHLocation
Mode0rncFunctionVIPLOADCONSWCHVIP Load Control
Switch0rncFunctionMULTICASTSUPINDMBMS Multicast Mode Support
Indicator0rncFunctionVIPSPECFREQSWCHVIP Specific Frequency Strategy
Switch0rncFunctionMBMSIURSUPINDMBMS over Iur Support
Indicator0rncFunctionGPSINFOROOTGPS Information
Root0rncFunctionIUULINSEQDLVINDIU Uplink in Sequence Delivery
Indicator whether According to Indication from
CN1rncFunctionWHTLSTSWITCHSwitch for White
List0rncFunctionCBSSWITCHCBS License0rncFunctionRNCLCSOVERIURSWLcs
over Iur Support Indicator0rncFunctionEBROADCASTSUPINDMBMS Enhanced
Broadcast Mode SupportIndicator0rncFunctionINITRRCONDCHType of
Transport Channel for Initial RRC Connection
Setup1rncFunctionVIPDLARFCNINDVIP Specific Downlink Carrier Central
Frequency Indicator0rncFunctionUPDASIB3CELNUMNumber of Cells
Updating SIB350rncFunctionUPUDRECFGTIMERWait Timer for Adjusting
Uplink and Downlink Reconfiguration by One Step
Upward(100ms)30rncFunctionMEASBALTIMERTimer of Deactivate
Compressed Mode for Balance Strategy Based On
Measurement(s)6rncFunctionT1DTimer for Event 1D in HSPA or
MBMS(s)0rncFunctionECN0THRADDNRLSHOThreshold of Adding New Radio
Link Based On Ec/N0 In Soft Handover(dB)-13Only valid if
AddNRLSHOSwch = 1rncFunctionINTERNACKPWROFSTHS-DPCCH NACK Power
Offset for Inter-NodeB Handover6rncFunctionSIRUPADDSTEPAdditional
Size for Uplink SIR Target Increasing When Consecutive Error TB
Occurs(dB)0.0rncFunctionCELCHGFASTCFGINDSwitch of Fast
Reconfiguration Function When the HS Service Cell was
Changed0Should enable?rncFunctionINTERCQIPWROFSTHS-DPCCH CQI Power
Offset for Inter-NodeB Handover5rncFunctionHARQRVCONFIGHARQ RV
Configuration1rncFunctionVLACPAINGINDVitrual LAC Paging Support
Indication0rncFunctionBWOVLDRELUENUMthe Release UE Number when Band
Exceeds Limit5rncFunctionMAXDHSRATEMaximum Bit Rate of HSDPA Across
Iur Interface(kbps)3650rncFunctionT4STPIFMEAACTRATTimer for
Stopping Inter-frequency Measurement and Activating Inter-RAT
Measurement(s)5rncFunctionRSCPTHRADDNRLSHOThreshold of Adding New
Radio Link Based On RSCP In Soft Handover(dBm)-108Not
usedrncFunctionTWAITCONTEXTREQWaiting Time for SRNS Context
Request(100ms)200rncFunctionHSDPACMASSOMODEHSDPA Associate CM
Method1rncFunctionPARALLELRRCSETUPSwitch of RNC Send RL SETUP and
RRC CONNECTION SETUP in Parallel when Setting up RRC
CONNECTION1rncFunctionULEFACHSFSpreading Factor Supported by Uplink
Enhanced CELL_FACH0rncFunctionCEDCHMAXRLCSIZECommon E-DCH Maximum
Uplink RLC PDU Size(Byte)[124@124@600]rncFunctionT321Inactivity
Time of E_FACH
Transmission(T321)(ms)1rncFunctionCEDCHMAXRETRTTI2Maximum Number of
Retransmissions for Common E-DCH MAC-d Flow (2ms
TTI)[3@3@3]rncFunctionNRETRANMaximum Number of Retransmissions of
the RRC CONNECTION RELEASE Message3rncFunctionCDTMROVDTHDCDT/MR
Overload Threshold(%)70rncFunctionDNUDRECFGTIMERWait Timer for
Adjusting Uplink and Downlink Reconfiguration by One Step
Downward(100ms)30rncFunctionMRUEMEASRPTTRMODMR-UE Measurement
Report Transfer Mode0rncFunctionCEDCHMULTISWICommon E-DCH MAC-d
Flow Multiplexing Switch0rncFunctionRABMEABALSTASWCHInter-Frequency
Balance Switch Based on Measurement0Should re-evaluate IFHO LB
strategy?rncFunctionTRESNDMEACTRLRELThe Time Threshold that the RNC
May Resend the MEASUREMENT CONTROL
RELEASE(s)30rncFunctionMRUEMEASRPTINTMR-UE Measurement Reporting
Interval(ms)2rncFunctionHEARTBEATUEVERThe Target of UE Version for
Heart Beat14Not used, currently URA PCH is not
enabledrncFunctionTIURELDELAYTimer for IU Release
Resource(100ms)3rncFunctionPCHTOAWSTime of Arrival Window
Startpoint for PCH(ms)44rncFunctionDCREDIRECTSTASWDual Carrier
Redirection Strategy Switch0rncFunctionGRESPARA60Global Reserved
Parameter 600Require parameter
descriptionrncFunctionBERTARGADPTIMERBER Target Adjust Timer in
Fast OLPC SIR Target Downward Adjustment Based on
BER500rncFunctionWAITRBCOMPTIMERTime of Waiting for RB
Setup/Reconfiguration/Release Response over Uu
Interface(s)5rncFunctionIURPWRCTLREQSWCHSwitch of Using DL Power
Control Request Information in Iur
Interface1rncFunctionCMINULPDUSIZEUplink Conversational Service
Minimum Uplink RLC PDU Size(byte)7rncFunctionPLMNSELECTMETHODPLMN
Select Method for MOCN Network
Sharing0rncFunctionINTERACKPWROFSTHS-DPCCH ACK Power Offset for
Inter-NodeB Handover6rncFunctionNONCMAXPDUSIZEDownlink
Non-Conversational Service Maximum MAC-d PDU Size
Extended(byte)600rncFunctionHEARTBEATFREQHeart Beat
Period(100ms)30Not used, currently URA PCH is not
enabledrncFunctionPOWHITELISTUSERPower Offset for White List
User(dB)0.0rncFunctionCODEUPTPRDUNITCode Update Period
Unit1rncFunctionVALIDTIMTBCOVPRDValid Time Window for the TB in
Shield Period(10ms)0rncFunctionDTOHSDELAYTHRDelay Time Threshold of
D/D->HS/D or HS/E after HS/D or HS/E ->D/D Triggering by
Channel Quality(s)10rncFunctionMINBERTARGETMinimum BER Target in
Fast OLPC SIR Target Downward Adjustment Based on
BER0rncFunctionMAXRATEWITHNVHSMaximum Bit Rate with HS-SCCH Less
for Non-VoIP/AMR(kbps)2rncFunctionINTERRATUPVERInter-RAT IuUP
Version Selection1rncFunctionTWAITDATAFWDWaiting Timer for SRNS
DATA FORWARD COMMAND(100ms)50rncFunctionGRESPARA50Global Reserved
Parameter 500Require parameter
descriptionrncFunctionRRCSETUPRETRANUMMaximum Number of
Retransmissions of the RRC CONNECTION
SEUTP2rncFunctionMRUEMEASTYPESWITMR-UE Measurement Type
Switch0Depends if we require the MR files to be
createdrncFunctionROUTETYPEUEBASEDThe Routing Select Type for
UE-Based0rncFunctionGRESPARA51Global Reserved Parameter 510Require
parameter descriptionrncFunctionGRESPARA52Global Reserved Parameter
520Require parameter descriptionrncFunctionGRESPARA53Global
Reserved Parameter 530Require parameter
descriptionrncFunctionRXBURSTLENGTHLength of Receiving Frames in
E-FACH DRX(frames)2rncFunctionONLYDNONHBThe Switch Indicates
whether Only Judge the Downlink Traffic on Heart Beat for Channel
Switching to PCH/IDLE1Not used, currently URA PCH is not
enabledrncFunctionTRRCCONSETUPEXPTime of Waiting for RRC CONNECTION
COMPLETE(100ms)100rncFunctionGRESPARA54Global Reserved Parameter
540Require parameter descriptionrncFunctionTWAITRELCMDWaiting Timer
of SRNS for IU RELEASE COMMAND while PS service handover from 3G to
2G(100ms)150rncFunctionGRESPARA55Global Reserved Parameter
550Require parameter descriptionrncFunctionBLERADJUSTSWITCHR99 CS
AMR Services BLER Target Adjustment
Switch0rncFunctionGRESPARA56Global Reserved Parameter 560Require
parameter descriptionrncFunctionGRESPARA57Global Reserved Parameter
570Require parameter descriptionrncFunctionCMAXPDUSIZEDownlink
Conversational Service Maximum MAC-d PDU Size
Extended(byte)65rncFunctionGRESPARA58Global Reserved Parameter
580Require parameter descriptionrncFunctionPCHTOAWETime of Arrival
Window Endpoint for PCH(ms)8rncFunctionGRESPARA59Global Reserved
Parameter 590Require parameter
descriptionrncFunctionMRUEPRDLOCMODEMR-UE Periodical Location
Measurement Mode1rncFunctionTRRCSETUPRETRANInterval of
Retransmission of RRC CONNECTION
SETUP(100ms)7rncFunctionDRXCYCLELENGTHCycle Length of Discontinue
Receiving of E-FACH1rncFunctionAMRGBRRESINDGBR of AMR Service
Whether to be Reserved Indicator1rncFunctionMRSERVICETYPEMR Service
TypeRequire More InfoRequire More InforncFunctionGRESPARA49Global
Reserved Parameter 490Require parameter
descriptionrncFunctionGRESPARA48Global Reserved Parameter
480Require parameter descriptionrncFunctionETTICOMEDCHCommon E-DCH
Transmission Time Interval(ms)1rncFunctionGRESPARA47Global Reserved
Parameter 470Require parameter
descriptionrncFunctionGRESPARA46Global Reserved Parameter
460Require parameter descriptionrncFunctionGRESPARA45Global
Reserved Parameter 450Require parameter
descriptionrncFunctionGRESPARA44Global Reserved Parameter
440Require parameter descriptionrncFunctionGRESPARA43Global
Reserved Parameter 430Require parameter
descriptionrncFunctionGRESPARA42Global Reserved Parameter
426Require parameter descriptionrncFunctionGRESPARA41Global
Reserved Parameter 410Require parameter
descriptionrncFunctionVIPINFOREQPRDVIP Information Require
period(s)18rncFunctionTWAITCELUPUUEXPTime of Waiting for CELL
UPDATE After RNC Sending Radio Link Deactivation Command for RB
Setup/Reconfiguration/Release Response Timer
Expiration(100ms)80rncFunctionCELLLDINFOVLDTIMDuration of Valid
Cell Load Info(s)300rncFunctionVIPESTNTFSWITCHVIP Exist
Notification Switch1rncFunctionTCNQUERYTimer for State
Query(100ms)1800rncFunctionDROPFORVIPSWITCHUser Drop Switch
Triggered by VIP1rncFunctionKUTRANUTRAN DRX Cycle Length
Coefficient6rncFunctionTWAITRLRESTORETime of Waiting for RADIO LINK
RESTORE INDICATION(100ms)100Should re-optimize to reduce long
silent duration?rncFunctionCODEUPTPRDCode Update
Period1rncFunctionULLCHTYPEINDLogical Channel Type Indication for
Common E-DCH MAC-d Flow[0@1@2]rncFunctionHSDSCHTOTPWRMETHHSPA Total
Downlink Power Allocation Method2rncFunctionCEDCHHARQPOTTI2HARQ
Power Offset for Common E-DCH MAC-d Flow (2ms
TTI)[6@6@6]rncFunctionCOVERMEABALSWCHInter-Frequency Balance Switch
Based on Measurement with Overlapping or Covering Relation0Should
re-evaluate IFHO LB strategy?rncFunctionNONCMINULPDUSIZEUplink
Non-Conversational Service Minimum Uplink RLC PDU
Size(byte)21rncFunctionHSUPACMASSOMODEHSUPA Associate CM
Method1Should set to 1?rncFunctionMAXBERTARGETMaximum BER Target in
Fast OLPC SIR Target Downward Adjustment Based on
BER95rncFunctionMAXCSDELAYMax CS
Delay(ms)60rncFunctionCSRRCONFACHSWCHSwitch of Non Emergency CS
Service Access to CELL_FACH On
RRC1rncFunctionCEDCHMAXRETRTTI10Maximum Number of Retransmissions
for Common E-DCH MAC-d Flow (10ms
TTI)[3@3@3]rncFunctionTRBRECFGCMPDTOFWait Time for RADIO BEARER
RECONFIGURATION COMPLETE when CELL_DCH to
CELL_FACH(s)15rncFunctionCEDCHMINRLCSIZECommon E-DCH Minimum Uplink
RLC PDU Size(Byte)[21@21@45]rncFunctionTWAITCELUPRLDACTTime of
Waiting for CELL UPDATE After RNC Waiting ACTIVE SET UPDATE
COMPLETE/ RECONFIGUATION COMPLETE of Hard Handover Timer Expiration
UPDATE COMPLETE Timer
Expiration(100ms)100rncFunctionCEDCHHARQPOTTI10HARQ Power Offset
for Common E-DCH MAC-d Flow (10ms
TTI)[6@6@6]rncFunctionHAPPYBITDELCEDCHHappy Bit Delay for Common
E-DCH(ms)3rncFunctionN308Maximum Number of Retransmissions of the
RRC CONNECTION RELEASE COMPLETE
Message(N308)1rncFunctionCMAXULPDUSIZEUplink Conversational Service
Maximum Uplink RLC PDU
Size(byte)124rncFunctionNONCMAXULPDUSIZEUplink Non-Conversational
Service Maximum Uplink RLC PDU
Size(byte)244rncFunctionFACHTOAWSTime of Arrival Window Startpoint
for FACH(ms)44rncFunctionVIPESTNTFNBRPRIOLowest Priority of
Neighbor Cell Notified of VIP Existing2rncFunctionFACHTOAWETime of
Arrival Window Endpoint for
FACH(ms)8rncFunctionINTRARATUPVERIntra-RAT IuUP Version
Selection2rncFunctionIURECNODELTAThe Offset of CPICH Ec/No in Iur
Interface Relative to the UE Measurement
Result(dB)0rncFunctionMRUEINICALLLOCMODEMR-UE Initial Call Location
Measurement Mode0rncFunctionTWAITACTSETUPCMPWaiting time length for
ACTIVE SET UPDATE COMPLETE(100ms)100rncFunctionUPDSIB3CELNTTime
Interval Updating SIB3 among
Cells(s)20rncFunctionMRUELOCMEARPTINTMR-UE Location Measurement
Reporting Interval(ms)0rncFunctionUEDRXINDIndication of UE with
Enhanced DRX1rncLocRncRNCSRVCCSWRNC SRVCC
Switch0rncLocRncCDTSWITCHCDT Function Switch0If require CDT, to
open?rncLocRncGSMLRANGEGSM Lower
Range[512@0@955]rncLocRncMRSWITCHMR Function Switch1If require MR,
to open?rncLocRncPSL2USWCHBYCSSwitch of Permit PS Handover from LTE
to UTRAN Because of CSFB1Required for LTE->3G CSFB
HOrncLocRncGSMURANGEGSM Upper
Range[885@124@1023]rncLocRncCSNULLNRISpecial Network Resource
Identifier in CS Domain65535rncLocRncAMRRNCADJUSTAMR Rate
Adjustment Switch for RNC0Required if want to use other AMR
bitratesrncLocRncLUARFCNUARFCN
Nlow[10562@9662]rncLocRncPSNULLNRISpecial Network Resource
Identifier in PS Domain65535rncLocRncFDDFREQRNGNUMNumber of FDD
UMTS Frequency Range2rncLocRncRNCPSHOLTESWRNC Switch for PS
Handover with LTE1rncLocRncINTEGRITYALGIntegrity Protection
Algorithm1This setting support UIA1 only. Need to support
UIA2?rncLocRncENCRYALGEncryption Algorithm3This setting support
UEA0 and UEA1 only. Need to support
UEA2?rncLocRncQOSNEGRENEGSWISwitch for QoS
Negotiation/Renegotiation0rncLocRncGSMBARANGENUMNumber of GSM BA
Range3rncLocRncDRBCSCENEDRBC Strategy For Channel Resource
utilization0rncLocRncUUARFCNUARFCN
Nupper[10838@9938]rncLocRncCSPLUSPSSWCHSwitch of PS Sevice Channel
Allocation for Concurrent CS+PS0rncLocRncSERVHOINDService Handover
Strategy Indicator15rncLocRncAMRWBMODE3USETAGAMR_WB 14.25k Use
Tag0rncLocRncNAMRINITIALRATENarrow-Band AMR Initial Data Rate for
High Cell Load(kbps)2Required if want to use other AMR
bitratesrncLocRncPSRTSERVHOSTRAService Handover Strategy of RNC for
PS RT Service1rncLocRncAMRWBMODE2USETAGAMR_WB 12.65k Use
Tag1rncLocRncAMRNBMODE2USETAGAMR_NB 5.90k Use
Tag0rncLocRncAMRSERVHOSTRAService Handover Strategy of RNC for
AMR1rncLocRncAMRWBMODE7USETAGAMR_WB 23.05k Use
Tag0rncLocRncAMRWBMODE4USETAGAMR_WB 15.85k Use
Tag0rncLocRncAMRNBMODE0USETAGAMR_NB 4.75k Use
Tag0rncLocRncAMRWBMODE5USETAGAMR_WB 18.25k Use
Tag0rncLocRncCDTIMEIACQSWITCHCDT-IMEI Acquisition
Switch0rncLocRncAMRWBMODE1USETAGAMR_WB 8.85k Use Tag1AMRWB
TrialrncLocRncAMRNBMODE3USETAGAMR_NB 6.70k Use
Tag0rncLocRncAMRNBMODE1USETAGAMR_NB 5.15k Use
Tag0rncLocRncAMRWBMODE6USETAGAMR_WB 19.85k Use
Tag0rncLocRncNEGGBRLEVNUMNegotiated GBR Level Number Shared by
Uplink and Downlink2rncLocRncCOMPMDCFGSTRACompressed Mode
Configuration Strategy0rncLocRncDLLOWLIMNEGGBRLower Limit of GBR
for Downlink Services Used for QoS
Negotiation/Renegotiation(kbps)64rncLocRncWAMRINITIALRATEWide-Band
AMR Initial Data Rate for High Cell
Load(kbps)4rncLocRncTNNSFTnnsf(s)10rncLocRncAMRNBMODE7USETAGAMR_NB
12.2k Use Tag1rncLocRncHOTOGSMPENTIMERHandover to GSM Penalty
Timer(s)30rncLocRncULLOWLIMNEGGBRLower Limit of GBR for Uplink
Services Used for QoS
Negotiation/Renegotiation(kbps)64rncLocRncAMRNBMODE4USETAGAMR_NB
7.40k Use Tag0rncLocRncAMRWBMODE8USETAGAMR_WB 23.85k Use
Tag0rncLocRncCS64SERVHOSTRAService Handover Strategy of RNC for
CS641rncLocRncR6MULRABRCFGMETHOnline-already Service
Reconfiguration Method for UE of Release 6 and after Release 6 When
Multi-RAB1rncLocRncAMRNBMODE6USETAGAMR_NB 10.2k Use
Tag0rncLocRncRLREFTIMEAJTSWITSwitch for RL Reference Time Adjust
During Diversity Mode0rncLocRncSERVHOCOMSTRAService Handover
Combination Strategy0rncLocRncPSNRTSERVHOSTRAService Handover
Strategy of RNC for PS NRT Service1rncLocRncAMRWBMODE0USETAGAMR_WB
6.60k Use Tag1rncLocRncAMRNBMODE5USETAGAMR_NB 7.95k Use
Tag0ueCnstT309Waiting Time After Requesting Connection
Establishment in Other System(eg. GSM) (T309)(s)8ueCnstT323Waiting
Time of UE Sending message SIGNALING CONNECTION RELEASE
INDICATION(with Cause)(T323)(s)7Only valid if URA PCH
enabledueCnstT314Waiting Time for Completion of Cell Update When
Radio Link Fails and Radio Bearer(s) Associated with T314
Exist(T314)(s)1ueCnstT305Period of Cell/URA Update When UE is in
CELL_FACH/CELL_PCH/ URA_PCH State(T305)(minutes)1ueCnstT315Waiting
Time for Completion of Cell Update When Radio Link Fails and Radio
Bearer(s) Associated with T315 Exist(T315)(s)2ueCnstT307Waiting
Time for Cell Reselection After UE is out of
Service(T307)(s)4ueCnstT313Waiting Time After DPCCH Established in
CELL_DCH State Losing Synchronization(T313)(s)3ueCnstT308Waiting
Time After Sending RRC CONNECTION RELEASE COMPLETE Message in
CELL_DCH State(T308)(ms)0ueCnstT312IDLEWaiting Time for
Receiving"In Sync"from L1 in Idle Mode (T312 in Idle
Mode)(s)2ueCnstT302Waiting Time After UE Sending CELL/URA UPDATE
Message(T302)(ms)5ueCnstT316Waiting Time for Cell
Selection/Reselection After UE is out of Service in
CELL_PCH/URA_PCH State(T316)(s)0ueCnstT304Waiting Time After UE
Sending UE CAPABILITY
INFORMATIONMessage(T304)(ms)4ueCnstT300Waiting Time After UE
Sending RRC CONNECTION REQUEST Message(T300)10ueCnstN302Maximum
Number of Retransmissions of the CELL/URA UPDATE Message
(N302)2ueCnstN315Maximum Number of Successive "In Sync" Received
from L1 During T313 is Activated ( N315)0ueCnstT312CONNECTEDWaiting
Time for Receiving "In Sync" from L1 in Connected Mode(T312 in
Connected Mode)(s)1ueCnstN312IDLEMaximum Number of "In Sync"
Received from L1 in Idle Mode (N312 in Idle Mode)0ueCnstN300Maximum
Number of Retransmissions of the RRC CONNECTION REQUEST Message
(N300)3ueCnstT323SWCHSwitch of T323 Broadcasting1ueCnstN304Maximum
Number of Retransmissions of the UE CAPABILITY INFORMATION Message
(N304)2ueCnstN313Maximum Number of Successive "Out of Sync"
Received from L1(N313)5ueCnstN312CONNECTEDMaximum Number of "In
Sync" Received from L1 in Connected Mode (N312 in Connected
Mode)0nodeBPLMNNUMNumber of PLMN for RAN
Sharing0nodeBTIMEDELAYTransport Time Delay(ms)Planning Parameter
(0)0 - 20ms (for normal sites)1 - 100ms 2 - 400ms (for VSAT
sites)nodeBHSSHARMETHODCo-NodeB HS-PDSCH Code Sharing
Method0nodeBMNC4RANSHARINGMNC for RAN Sharing[0]For RAN
SharingnodeBNODEBTYPENodeB Type0nodeBMCC4RANSHARINGMCC for RAN
Sharing[460]For RAN SharingnodeBMINCEPERCENTMinimal percent of CE
can be used by the PLMN(%)[0.0]For RAN SharingnodeBTIPRELLINKPROIP
Link Broken Protection Time
Length(100ms)100nodeBDIVCONTRLFIELDDiversity Control
Field0nodeBADJTYPEAdjustment Type for DL Power
Balance1nodeBTATMRELLINKPROATM Link Broken Protection Time
Length(100ms)100nodeBTWAITNBREACHTime Delay of Deleting Cell When
NodeB is Unreachable(100ms)600nodeBAUDITTIMERNodeB Resource Audit
Timer(100ms)300nodeBHSSHARUPTPRDCo-NodeB HS-PDSCH Code Sharing
Update Period(s)20nodeBTIMEDELAYJITTERTransport Time Delay
Jitter(ms)5nodeBSUPTCGTDETINDSupport R5/R6 Congestion Detection
Indicator0What is this?utranCellCELLINDIVOFFSETCell Individual
Offset(dB)Planning Parameter
(0.0)utranCellCGTCTLPRIINDEXApplication Priority Index (Congestion
Control)[2]utranCellMULMDUTRANCELINDUTRAN Cell of Multi-Mode System
Indicator0utranCellSIB12INDSIB12 Indicator0Should explore using
SIB12?utranCellLATITUDEDegree of Latitude for Cell
Center0.0utranCellACCESSPERCENTAccess Percent of the PLMN for
Non-Supporting UEs[0]utranCellSTTDSUPTINDSTTD Support
Indicator1utranCellINNERANGLEInner Angle0utranCellPSCHPWRPrimary
SCH Power(dB)-5.0utranCellANTETYPEAntenna
Type0utranCellLOADSCENECell Load Scene0utranCellHSPASPTMETHHSPA
Support MethodOptimization Parameter (3)1 - HSDPA3 - HSDPA +
HSUPAutranCellTRFPCINDEXTraffic PC IndexOptimization Parameter
(3)utranCellPICHPWRPICH Power(dB)-7utranCellRNCIDRNC Identity of
UTRAN cellutranCellPSBARACNUMNumber of Barred AC in PS
Domain[2]utranCellURANUMURA Number1utranCellMNCMobile Network
Code[16]utranCellRACRouting Area Code1utranCellDIVPCINDEXDiversity
PC IndexOptimization Parameter (3)utranCellCELLDESCRIPTYPECell
Description Type0utranCellOCNSCODECode Node Number with SF =128 for
OCNS[1]utranCellSCCPCHCFGSCENESCCPCH Configuration
Scene0utranCellDCHSDSCHSUPPTINDDual-Cell HS-DSCH Support
Indication1utranCellUSEOFHCSUse of HCS1utranCellTCELLT_CellPlanning
ParameterutranCellPRIMSCRACODECell Primary Scrambling CodePlanning
ParameterutranCellGARPTTYPEGeographical Area Report
Type0utranCellIMPULL2SUPTINDCell Uplink Enhanced Layer 2 Support
Indicator0utranCellPLMNNUMPLMN Number of Sharing the
Cell1utranCellMAXDLTXPWRCell Maximum Transmission
Power(dBm)43.0utranCellLATITUDESIGNLatitude Sign for Cell
Center0utranCellCELMIMO64QAMINDCell MIMO and DL64QAM Combined
Capability Support Indicator0utranCellUNCERTCODEHorizontal Accuracy
Code0utranCellCELLRADIUSCell Radius(m)0utranCellCELLRADIUSSCENECell
Radius Scene0utranCellTRFCATRATMIDXInter-RAT Measurement
Configuration Index Related to Traffic CategoryOptimization
ParameterIndices to be standardized across all RNC. Number of
indices to be streamlined to only a few required combination of
trigger thresholdsutranCellDUARFCNDUARFCNPlanning
ParameterutranCellSECTORIDSector IdentityPlanning
ParameterutranCellFDPCHSUPTINDCell F-DPCH Support
Indicator0utranCellCSBARACNUMNumber of Barred AC in CS
Domain[2]utranCellURAURA IdentityPlanning ParameterFollow LAC
IDutranCellCLASSZONEINDClassified Zone
Indicator0utranCellPRIREDIRECTRATPrior Redirect RAT
Indicator2utranCellSSCHPWRSecondary SCH
Power(dB)-5.0utranCellLACLocation Area CodePlanning
ParameterutranCellALTITUDEACCAltitude
Accurary(m)0utranCellSACPCService Area Code for CS and PS
DomainPlanning ParameterFollow Cell IDutranCellPOLYLATITUDEDegree
of Polygon Point
Latitude(degree)[[email protected]@0.0]utranCellCELLDCMIMOSUPINDCell Dual
Cell+MIMO Support Indicator0utranCellMIMOSUPTINDCell MIMO Support
Indicator0utranCellSCHTSTDINDSCH TSTD
Indicator1utranCellPREFTRAFTYPEPreferred Traffic
Type7utranCellPOLYLONGITUDEDegrees of Polygon Point
Longitude(degree)[[email protected]@-180.0]utranCellANTELONGITUDEDegrees
of Antenna Longitude(degree)-180.0utranCellPCCPCHSTTDINDPCCPCH STTD
Indicator0utranCellVAMSUPINDCell VAM Support
Indicator0utranCellSACBService Area Code for BC DomainPlanning
ParameterFollow Cell IDutranCellLONGITUDEDegrees of Longitude for
Cell Center-180.0utranCellPCPICHPWRP-CPICH Power(dBm)Optimization
Parameter (33.0)utranCellBPRIACINDEXBasic Priority AC
Index[1]utranCellHOCELSELSCENEMobility Configuration
Scene0utranCellBCHPWRBCH
Power(dB)-2.0utranCellANTELATITUDESIGNAntenna Latitude
Sign0utranCellCSACBARREDOMCRCS Domain Specific Access Class N
Barred Indicator[65535]utranCellPSACBARREDOMCRPS Domain Specific
Access Class N Barred Indicator[65535]utranCellCSDSARSWHSwitch of
CS Domain DSAR[0]utranCellANTEALTITUDEDIRDirection of Antenna
Altitude0utranCellMIMOPILOTMODEMIMO Pilot
Mode0utranCellPOLYLATITUDESIGNPolygon Point Latitude
Sign[0@0@0]utranCellEFDPCHSUPINDCell Enhanced F-DPCH Support
Indicator0utranCellCELLSCENPathloss
Scenario0utranCellULBLERHOSWCHUL BLER Switch for
Handover0utranCellPSDSARPOLLINGSWHSwitch of Polling in PS Domain
DSAR[0]utranCellAICHPWRAICH Power(dB)-7utranCellSUPT64QAMINDCell
64QAM Support Indicator1utranCellCS64SWITCHSwitch of CS 64kbps
Establishment1utranCellCOMMONPLMNINDCommon PLMN
Indicator[1]utranCellPCPICHTXDIVINDP-CPICH Tx Diversity
Indicator0utranCellCLM1SUPTINDClosed Loop Mode 1 Support
Indicator1utranCellLOADBALANCESCENELoad Balance
Scene0utranCellCELLTYPECell Type1utranCellEFACHSPPTINDDownlink
Enhanced CELL_FACH Support Indicator0utranCellIMPDLL2SUPTINDCell
Downlink Enhanced Layer 2 Support Indicator1utranCellMCCMobile
Country Code[502]utranCellSCENARIOTYPEScenario TypeDefault
SceneutranCellPCHPWRPCH Power(dB)-3.0utranCellBGNOISCENEBackground
Noise Automatic Adjustment
Scene0utranCellHCSPRIOHCS_PRIO0utranCellSUPTMULUSDETINDMulti-User
Detection Support Indicator0utranCellULEFACHSUPPORTUplink Enhanced
CELL_FACH Support Indicator0utranCellCSDSARPOLLINGSWHSwitch of
Polling in CS Domain DSAR[0]utranCellSCHPRIINDEXScheduling Priority
Index[1]utranCellNODEBNONodeB NumberPlanning
ParameterutranCellSACBPRESACB Configuration Tag0utranCellTWAITWait
Time for RRC Connection
Reestablishment(s)5utranCellMBMSSUPTINDSupport MBMS
Indicator0utranCellPOLYGONPOINTNUMPolygon Point
Number3utranCellANTELATITUDEDegree of Antenna
Latitude0.0utranCellHSDSTATHSDPA Function
Status1utranCellDLPWRHOSWCHDL Tx Power Switch for
Handover0utranCellSTTDMIMOBINDINDSTTD and MIMO Activation Binding
Indicator0utranCellMODULECMP Module NumberPlanning
ParameterutranCellALTITUDECell Altitude for Cell
Center(m)0utranCellCLOSEFREFUNSWITSwitch of Closing Frequency
Intelligently Function0utranCellTRFCATINTRAMIDXIntra-frequency
Measurement Configuration Index Related to Traffic
CategoryOptimization ParameterIndices to be standardized across all
RNC. Number of indices to be streamlined to only a few required
combination of trigger thresholdsutranCellUNCERTALTITUDEAltitude
Accurary Code0utranCellOFFSETANGLEOffset Angle0utranCellLCIDLocal
Cell IdentityPlanning ParameterutranCellANTEALTITUDEAntenna
Altitude(m)0utranCellSCPICHSUPINDS-CPICH Support
Indicator0utranCellHSUSTATHSUPA Function StatusOptimization
Parameter (1)utranCellRADIOCAPACITYRadio Capacity of
Cell1utranCellOCNSCODENUMBERNumber of the Codes with SF =128
Ordered for OCNS0utranCellTUTRANGPSSPTINDTUTRAN-GPS Measurement
Support Indicator0utranCellULPWRHOSWCHUE Tx Power Switch for
Handover0utranCellPAGINGLOCABARSWHSwitch of Paging and
Location/Registration
Restriction[0]utranCellLDCTLPRIINDEXApplication Priority Index
(Load Control)[1]utranCellALTITUDEDIRDirection of Altitude for Cell
Center0utranCellTRFCATINTERMIDXInter-frequency Measurement
Configuration Index Related to Traffic CategoryOptimization
ParameterIndices to be standardized across all RNC. Number of
indices to be streamlined to only a few required combination of
trigger thresholdsutranCellCPCSUPTINDCell CPC Support
Indicator0utranCellPSDSARSWHSwitch of PS Domain
DSAR[0]utranCellMIMOINDMIMO Indicator0utranCellTTI2MSSUPTINDCell
HSUPA 2ms TTI Support Indicator1utranCellUUARFCNUUARFCNPlanning
ParameterutranCellCONFIDENCEConfidence(%)0utranCellFREQBANDINDFrequency
Band Indicator0utranCellMBMSSTATMBMS Function
Status0utranCellEDCHNUMLEVE-DCH User Number Level Used for HSUPA
Adaptive Transmission[2@4]utranCellFRECLSOPNTRIGTMTrigger Time of
Judgment Based on UE Number During Closing Frequency
Intelligently(s)300utranCellDLCACSWITCHCell Downlink Admission
Control Switch1utranCellEFACHBANDWIDTHTransport Band Width for
Downlink Enhanced CELL_FACH64utranCellDRXONFACHINDE-FACH DRX
Support Indication in Cell0utranCellRRCSIGUSRNUMTHRThreshold of the
Number of the RRC Signaling Users Co-Exist in the
Cell200utranCellNRTMAXRATEEDCHMaximum Bit Rate on E-DCH for NRT PS
RAB in Serving Cell(kbps)5760utranCellINTRAMEASQUANUTRAN
Measurement Quantity for Intra-frequency
Measurements0utranCellADDNRLSHOSWCHAdding New Radio Link Judgement
Switch0utranCellSTARTTIMETOCLSFStart Time to Close Frequency
Intelligently(h:min:sec)22:0:0utranCellPSREESTSWITCHCell Switch of
PS Call Re-establishment in the
SRNC63utranCellPAGINGSENDTIMESSending Times of Paging
Message2utranCellINTRATHOMTHInter-RAT Handover
Method1utranCellPATHLOSSNominal
Pathloss(dB)130utranCellPCPIPWRDNTMWINTime Interval between two
Downgrade of P-CPICH Power Used to Switch Off Frequency
Intelligently(100ms)10utranCellCRESPARA2Cell Reserved Parameter
20Require parameter descriptionutranCellCRESPARA1Cell Reserved
Parameter 15Require parameter descriptionutranCellCRESPARA4Cell
Reserved Parameter 40Require parameter
descriptionutranCellCRESPARA3Cell Reserved Parameter 35Require
parameter descriptionutranCellCRESPARA6Cell Reserved Parameter
60Require parameter descriptionutranCellCRESPARA5Cell Reserved
Parameter 50Require parameter descriptionutranCellCRESPARA8Cell
Reserved Parameter 80Require parameter
descriptionutranCellCRESPARA7Cell Reserved Parameter 70Require
parameter descriptionutranCellCRESPARA9Cell Reserved Parameter
90Require parameter descriptionutranCellNRTMAXDLRATEDCHMaximum Bit
Rate on DL DCH for NRT PS RAB in Serving
Cell(kbps)384utranCellDPCCHPCPLENDPCH PC Preamble
Length0utranCellRRCRDTSWCHSwitch of RRC Redirection Triggered by
Radio Resource Congestion0utranCellRSCPQUALTHRDCpich RSCP Threshold
for Blind Handover-108Require to optimize?utranCellMAXRATEMDMaximum
Allowable Rate Being Adjusted in Macro
Diversity(kbps)384utranCellPORABHARDHOPower Offset for Downlink
DPCH Initial Power Calculation when RAB Hard Handover3.0Document
default = 1.0dB?utranCellCELLBARACSWHSwitch of Cell
Restriction0utranCellDLCONTROLEDMBRDL Controlled
MBR(bps)21096000utranCellINTERHOTACTICInter-frequency Handover
Tactic3utranCellCELLBARPOLLINGSWHSwitch of Polling in Cell
Restriction0utranCellCRESPARA20Cell Reserved Parameter 200Require
parameter descriptionutranCellSIB4INDSIB4 Indicator0Explore to use
SIB4?utranCellCRESPARA19Cell Reserved Parameter 190Require
parameter descriptionutranCellCRESPARA18Cell Reserved Parameter
180Require parameter descriptionutranCellMRCELLMEASSWITMR-CELL
Measurement Switch0Require for MR?utranCellCRESPARA17Cell Reserved
Parameter 170Require parameter descriptionutranCellCRESPARA16Cell
Reserved Parameter 160Require parameter
descriptionutranCellCRESPARA15Cell Reserved Parameter 150Require
parameter descriptionutranCellCRESPARA14Cell Reserved Parameter
140Require parameter descriptionutranCellDETSETHOSWCHDetected Set
Handover Switch1utranCellDLTPCNDL TPC Pattern 01
Count14utranCellPCCPCHINFSIB6PREPCCPCH Information in SIB6
Configuration Tag1utranCellPSNUMTHRD1Non-VIP PS User Number
Threshold without VIP20utranCellPCPIPWRDNSTEPP-CPICH Power Down
Step Size Used to Switch Off Frequency
Intelligently(dB)1.0utranCellPSNUMTHRD2Non-VIP PS User Number
Threshold When VIP Exists10utranCellCELAVASUBCHACell Available
Subchannel Number Continuous Setting1utranCellCRESPARA10Cell
Reserved Parameter 100Require parameter
descriptionutranCellCSNUMTHRD2Non-VIP CS User Number Threshold When
VIP Exists10utranCellCRESPARA11Cell Reserved Parameter 110Require
parameter descriptionutranCellCSNUMTHRD1Non-VIP CS User Number
Threshold without VIP20utranCellRATHOTACTICInter-RAT Handover
Tactic2utranCellCRESPARA12Cell Reserved Parameter 120Require
parameter descriptionutranCellCRESPARA13Cell Reserved Parameter
130Require parameter descriptionutranCellNONINTRAMEASQUANUTRAN
Measurement Quantity for Inter-frequency and Inter-RAT
Measurements2utranCellCCHFACTORCommon Transfer Bandwidth Discount
Factor for Channel(%)50utranCellPOSETUPPower Offset for Downlink
DPCH Initial Power Calculation when Call Setup6.0Document default =
0dB?utranCellCELLBARACNUMNumber of Cell Barred
AC2utranCellBARINTERVALTime Interval of Barred
AC(s)60utranCellORIBCKNOISEOriginal Background Noise
Configuration(dBm)-106.0utranCellDEFAULEDCHNUMLEVDefault E-DCH User
Number Level2utranCellAMRULLDTHRDCell Uplink Load Threshold for AMR
Data Rate Decision(dB)60.0utranCellCHOSTRAMULRATHOChoice Strategy
in Multi-RAT Handover0utranCellULCTRLMBRSWITCHUL Controlled MBR
Switch0utranCellSOFTHOMTHSoft Handover
Method1utranCellSERVHOSWCHService Handover
Switch1utranCellSIMCOMPUSERNUMUser Number with Compressed Mode
Activation for Balance Strategy Based On
Measurement16utranCellPOSRBHARDHOPower Offset for Downlink DPCH
Initial Power Calculation when SRB Hard Handover6.0Document default
= 4.0dB?utranCellVIRTUALLACVitrual Location Aera
Code[65535@65535]utranCellMRCELMRPTINTCOEFMR-CELL Measurement
Reporting Interval Coefficient3utranCellDLEFACHUSERNUMMaximum
Number of Users on Downlink Enhanced
CELL_FACH64utranCellMRUEMEASSWITMR-UE Measurement
Switch0utranCellPOREESTABLISHPower Offset for Downlink DPCH Initial
Power Calculation when RAB
Re-Establishment.2.0utranCellULCACSWITCHCell Uplink Admission
Control Switch0To be trialutranCellINTERHOMTHInter-frequency
Handover Method1utranCellBCKNOISEADJSWHBackground Noise Automatic
Adjustment Switch1utranCellCOVERPRDShield Period for Increasing SIR
Target in Threshold Algorithm6utranCellRTMAXRATEEDCHMaximum Bit
Rate on E-DCH for RT PS RAB in Serving
Cell(kbps)5760utranCellTRLFAILURETimer Length for Trigger Radio
Link Failure Procedure After NodeB Receive N_OUTSYNC_IND
Consecutive Out-of-Sync
Indication(T_RLFAILURE)(s)4.0utranCellAMRDLLDTHRDCell Downlink Load
Threshold for AMR Data Rate Decision50utranCellSRBDELAYSRB
Delay7utranCellHSUPAADATRANSWCHHSUPA Adaptive Transmission
Switch0Should explore?utranCellENDTIMETOCLSFEnd Time to Close
Frequency Intelligently(h:min:sec)7:0:0utranCellECNOQUALTHRDCpich
Ec/N0 Threshold for Blind Handover-13Require to
optimize?utranCellNUMOUTSYNCINDThe Number of Consecutive
Out-of-Sync Indications NodeB Received After which the Timer
T_RLFAILURE Shall be
Started(N_OUTSYNC_IND)70utranCellSIB7ORIGINATORSib7
Originator0utranCellPOSOFTHOPower Offset for Downlink DPCH Initial
Power Calculation when Soft or Softer
Handover0.0utranCellCSREESTSWITCHCell Switch of CS Call
Re-establishment in the SRNC63utranCellUENUMTHRESHCLSUE Number
Threshold Used for Closing Frequency
Intelligently2utranCellIFORRATHOSWCHInter Frequency or Inter RAT
handover SwitchOptimization Parameter (3)2 - Only IRAT3 - IFHO
before IRATutranCellFORBTIMAFTOPNFForbidden Time of Closing After
Opening the Frequency(hour)0.5utranCellNRTMAXULRATEDCHMaximum Bit
Rate on UL DCH for NRT PS RAB in Serving
Cell(kbps)384utranCellPCPIPWRDNSTEPTMTimes of Downgrade of P-CPICH
Power with Equal Step Used to Switch Off Frequency
Intelligently33utranCellABSPRIRESELSWCHAbsolute Priority
Reselection Criteria SwitchOptimization Parameter (0)0 - use
QQUALMIN (CelSel)1 - use QQUALMINFDD
(PriSel)utranCellCPICHECN0Default CPICH
Ec/No-7.0utranCellRTMAXULRATEDCHMaximum Bit Rate on UL DCH for RT
PS RAB in Serving Cell(kbps)384utranCellSIB6INDSIB6
Indicator0utranCellOPENFREALGSwitch of Algorithm Used to Open the
Frequency Intelligently2utranCellREFSFLAYERReference SF Layer Used
for Code Reservation in CAC5utranCellUL16QAMSWICell Uplink 16QAM
Support Indicator0utranCellRTMAXDLRATEDCHMaximum Bit Rate on DL DCH
for RT PS RAB in Serving Cell(kbps)384utranCellNUMINSYNCINDThe
Number of Consecutive In-Sync Indications NodeB Received After
which RL Restore Procedure Shall be
Triggered(N_INSYNC_IND)4utranCellULCONTROLEDMBRUL Controlled
MBR(bps)5760000utranCellDLCTRLMBRSWITCHDL Controlled MBR
Switch0utranCellPRACHSIB6PREDynamic Persistence Level Information
of SIB6 PRACH in SIB7 Configuration Tag0CHspaMINNUMOFHSPDSCHMinimum
Number of HS-PDSCH1CHspaNUMOFERGHICHNumber of
E-RGCH/E-HICHOptimization Parameter (1)1 - 20 users2 - 40 users3 -
60 usersCHspaEDCHTRAFLIMITMaximum Number of Users on
E-DCHOptimization Parameter (64)CHspaNUMOFEAGCHNumber of
E-AGCH1CHspaMAXNUMOFHSPDSCHMaximum Number of
HS-PDSCH15CHspaNUMOFHSPDSCHNumber of
HS-PDSCH5CHspaHSDSCHTRAFLIMITMaximum Number of Users on
HS-DSCH64CHspaDEDICOMEAGCHSWIE-AGCH Multiplexing Switch in
Dedicated and Common E-DCH1CHspaCODEUPTHYASF512 Number to Decrease
HS-PDSCH Number16CHspaMAXHSPAPWRRTOMaximum HSPA Total Downlink
Power(%)70CHspaHSSHAREINDCo-NodeB HS-PDSCH Code Sharing
Indicator0CHspaNUMOFHSSCCHNumber of
HS-SCCH2CHspaCEDCHUSERNUMMaximum Number of Users with Traffic on
Common E-DCH in Enhancecd Uplink CELL_FACH
State64CHspaDPCHCODEHYSF512 Number to Increase HS-PDSCH
Number16CHspaHSPAPWRRATIOHSPA Total Downlink
Power(%)40CHspaNSERVTOTOTALPWRTarget Non-serving E-DCH to Total
E-DCH Power Ratio(%)15CHspaHSPDSCHBITRATEHS-PDSCH Bit
Rate(kbps)700CHspaIURCDREASSDROPSwitch for DRNC Code Re-Assignment
Radio Link Release0CHspaMINHSPAPWRRTOMinimum HSPA Total Downlink
Power(%)3CHspaHSNBASSINDHS-PDSCH Code NodeB Assignment Support
Indicator0CHspaMAXRTWPMaximum Target Received Total Wideband
Power(dB)Optimization ParameterTo be optimized in conjunction with
UL AC / OLCCHspaCHSGBRRESLMTIDXCell Limiting HSDPA GBR Resource
Consumption Index1CelSelTCRMAXHYSTAdditional Time Period Before the
UE Can Exit High-mobility in Case of HCS Usage
(TCrMaxHyst)(s)0CelSelDLTAQRXLEVMINPRIncrement to the Minimum
Required Received Level in the Cell Configuration
Tag0CelSelSINTRASEARCHPRESintrasearch Configuration
Tag0CelSelQQUALMINMinimum Required Quality Level in the Cell
(Qqualmin)(dB)-17Should it be standardized same as QQUALMINFDD
(-18dB)?CelSelSINTERSEARCHPRESintersearch Configuration
Tag0CelSelOTHERRATINFOPREInter-System Information Configuration
Tag1CelSelNOHCSTCRMAXHYSTAdditional Time Period Before the UE Can
Revert to Low-Mobility Measurements in Case of Non-HCS Usage
(Non-HCS_TCRmaxHyst)(s)0CelSelNCRMaximum Number of Cell
Reselections (NCR)8CelSelSSEARCHRATInter-System Measurement Trigger
Threshold for Cell Reselection (Ssearch,RAT)(dB)2Need to
re-optimize?CelSelQQUALMINOFFSETQqualmin-offset(dB)16CelSelOPERATORUSEINDCell
Reserved for Operator UseOptimization Parameter (1)0 - Reserved1 -
Not ReservedCelSelQHYST2SPCHReselection Hysteresis 2 of Serving
Cell for UE in CELL_PCH or URA_PCH State
(QHyst2s,PCH)(dB)2CelSelTRESELECTIONPCHCell Reselection Timer Value
for UE in CELL_PCH or URA_PCH State
(Treselections,PCH)(s)2CelSelQQULMNOFFSTPREQqualmin-offset
Present0CelSelINTERRATSFInter-RAT Scaling Factor for
Treselection2.0CelSelTRESELECTIONFACHCell Reselection Timer Value
for UE in CELL_FACH State
(Treselections,FACH)(s)2.0CelSelQRXLVMNOFFSTPREQrxlevmin-Offset
Present0CelSelHCSSRVCELINFOPREHCS Serving Cell Information
Configuration Tag0CelSelCELLRSVEXTCell Reservation
Extension1CelSelCELLBARREDINDCell Barred
Indicator2CelSelQHCSRSCPQuality Threshold Level for Applying
Prioritised Hierarchical Cell Reselection(QHcs) When Measurement
Quantity is CPICH RSCP(dBm)-92CelSelQHYST2SReselection Hysteresis 2
of Serving Cell (QHyst2s)(dB)2CelSelDEFSIBSUPTSWCHSwitch of
Deferred SIB11/11bis/12 Support0CelSelSSEARCHHCSPRESsearchHCS
Configuration Tag0CelSelSPSFSpeed Dependent Scaling Factor for
Treselection0.5CelSelINTERFREQSFPREInter-frequency Scaling Factor
for Treselection Configuration Tag0CelSelQHYST2SFACHReselection
Hysteresis 2 of Serving Cell for UE in CELL_FACH State
(Qhyst2s,FACH)(dB)2CelSelQHYST1SFACHReselection Hysteresis 1 of
Serving Cell for UE in CELL_FACH State (QHyst1s,FACH
)(dB)10CelSelQRXLEVMINOFFSETQrxlevmin-offset(dB)16CelSelQUALMEASMeasurement
Quantity for Cell Selection and Reselection1CelSelQRXLEVMINMinimum
Required Received Level in the Cell
(Qrxlevmin)(dBm)-115CelSelTBARREDCell Barred
Time(Tbarred)(s)0CelSelINTERRATSFPREInter-RAT Scaling Factor for
Treselection Configuration Tag0CelSelNOHCSTCRMAXDuration for
Evaluating Allowed Amount of Cell Reselection(s) in Case of Non-HCS
Usage (Non-HCS_TCRmax)(s)1CelSelSSEARCHHCSMeasurement Trigger
Threshold for HCS Cell Reselection
(SsearchHCS)(dB)9CelSelDLTAQRXLEVMINIncrement to the Minimum
Required Received Level in the Cell
(DeltaQrxlevmin)(dB)-2CelSelQHYST1SReselection Hysteresis 1 of
Serving Cell (QHyst1s)(dB)10CelSelSHCSRATInter-System Measurement
Trigger Threshold for HCS Cell Reselection
(SHCS,RAT)(dB)9CelSelSINTERSEARCHInter-Frequency Measurement
Trigger Threshold for Cell Reselection
(Sintersearch)(dB)10CelSelINFREQRESELINDIntra-frequency Cell
Reselection Indicator0CelSelSHCSRATPRESHCS,RAT Configuration
Tag0CelSelTRESELECTIONCell Reselection Timer Value
(Treselections)(s)1CelSelNOHCSNCRMaximum Number of Cell
Reselections in Case of Non-HCS Usage
(Non-HCS_NCR)8CelSelQHYST1SPCHReselection Hysteresis 1 of Serving
Cell for UE in CELL_PCH or URA_PCH State
(QHyst1s,PCH)(dB)10CelSelSINTRASEARCHIntra-Frequency Measurement
Trigger Threshold for Cell Reselection
(Sintrasearch)(dB)10CelSelSLIMITRATHigh HCS Priority Inter-system
Cell Measurement Threshold for Cell Reselection
(Slimit,SearchRAT)(dB)6CelSelQHCSECNOQuality Threshold Level for
Applying Prioritised Hierarchical Cell Reselection (QHcs) When
Measurement Quantity is CPICH Ec/No(dB)-12.0CelSelSPSFPRESpeed
Dependent Scaling Factor for Treselection Configuration
Tag0CelSelINTRARPTQSIB3Intra-frequency reporting quantity SIB3 when
SIB11/11bis/12 deferred reading0CelSelACBARREDOMCRAccess Class N
Barred Indicator (N=0..15)65535CelSelINTERFREQSFInter-frequency
Scaling Factor for Treselection2.0CelSelTCRMAXDuration for
Evaluating Allowed Amount of Cell Reselection(s)
(TCRmax)(s)1PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursEUTRANHIGHTHRES2Reselection Threshold 2 for Inter-RAT
Layers of High Priority in
EUTRAN(Threshx,high2)(dB)[10@10]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursQQUALMINFDDQqualmin of UTRAN for Cell
Reselection(dB)[-18]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursEUTRANLOWTHRES2Reselection Threshold 2 for Inter-Rat
Layers of Low Priority in
EUTRAN(Threshx,low2)(dB)[10@10]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursEUTRANINTERFNUMNumber of EUTRAN Centre
FrequenciesOptimization Parameter1 or 2PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursGERANHIGHTHRESHReselection Threshold for Inter-RAT Layers
of High Priority in GERAN(dB)[14]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursGERANPRIORITYAbsolute Priority of Inter-RAT Layers in
GERAN[1]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursUTRANHIGHTHRESHReselection Threshold for Inter-Frequency
Layers of High Priority in UTRAN(dB)[14]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursEUTRANHIGHTHRESHReselection Threshold for Inter-RAT
Layers of High Priority in EUTRAN(dB)[20@20]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursUTRANLOWTHRESHReselection Threshold for Inter-Frequency
Layers of Low Priority in UTRAN(dB)[14]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursQRXLEVMINGSMQrxlevmin of GSM for Cell
Reselection(dBm)[-115]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursQRXLEVMINEUTRAQrxlevmin of EUTRAN for Cell
Reselection(dBm)[-128@-128]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursUTRANINTERFNUMNumber of UTRAN Centre
Frequencies0PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursEUTRANLOWTHRESHReselection Threshold for Inter-RAT Layers
of Low Priority in EUTRAN(dB)[14@14]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursEUTRANPRIORITYAbsolute Priority of Inter-RAT Layers in
EUTRAN[7@7]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursTHRESHRSRQINDThreshold of RSRQ indicator[0@0]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursUTRANPRIORITYAbsolute Priority of Inter-Frequency Layers
in UTRAN[0]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursQQUALMINEUTRAQqualmin of EUTRAN for Cell
Reselection(dB)[-18]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursUTRANUARFCNUTRAN Absolute Radio Frequency Channel
Number[0]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursQRXLEVMINFDDQrxlevmin of UTRAN for Cell
Reselection(dBm)[-115]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursGSMBANDINDICATORGsm Band Indicator[0]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursGSMCELLGROUPNUMNumber of GSM Frequency
Groups0PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursALLOWMEASBANDEUTRAN Allowed Measurement
Bandwidth[3@3]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursSERVCELPRIORITYAbsolute Priority of Serving Cell for Cell
Reselection6PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursSTARTARFCNGSM Starting ARFCN[0]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursGERANLOWTHRESHReselection Threshold for Inter-RAT Layers
of Low Priority in GERAN(dB)[14]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursTHRESHSERVINGLOWServing Cell Reselection Threshold for
Absolute Priority Reselection Criteria(dB)10PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursDLEARFCNDownlink EUTRAN Absolute Radio Frequency Channel
Number[3400@1750]PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursSPRIORITYSEARCH1CPICH RSCP Measurement Trigger Threshold
for Absolute Priority Reselection Criteria(dB)10PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursSPRIORITYSEARCH2CPICH EcN0 Measurement Trigger Threshold
for Absolute Priority Reselection Criteria(dB)7PriSel
nskhoo: nskhoo:only valid for cells with LTE
neighboursTHRESSERVINGLOW2Serving Cell Reselection Threshold 2 for
Absolute Priority Reselection
Criteria(Threshserving,low2)(dB)6LdCtrlDLDECRATESWDownlink Switch
for Shielding Rate Reduction1LdCtrlMAXNUMUEOFDECRATMaximum Number
of UE Decreasing Rate When Congestion1LdCtrlULFORCEHANDOFFSWUplink
Switch for Shielding Forced Handover0To re-visit OLC
algorithmLdCtrlNODEBSAFETHRSafe Threshold for
NodeB(%)95LdCtrlULMAXDRPURNUMMaximum Number of Uplink Forced Drop
Users Every Time5LdCtrlFORCERABTOFASWITThe Switch of Forced RAB to
FACH of the online I/B users in Congestion0To re-visit OLC
algorithmLdCtrlDLOVERLDDownlink Common Overload
Threshold(%)95LdCtrlDLMAXDRPURNUMMaximum Number of Downlink Forced
Drop Users Every Time1LdCtrlULHIGHLDUplink High Load Threshold for
R99 CS AMR Services BLER Target
Adjustment55.0LdCtrlDLHIGHLDDownlink High Load Threshold for R99 CS
AMR Services BLER Target Adjustment70LdCtrlFORCEDRABRELSWITThe
Switch of Forced RAB Release for Online Users in
Congestion1LdCtrlMAXGBRDECNUMMaximum Number of Services Whose GBR
Can Be Decreased in Load Control Every Time Shared by Uplink and
Downlink5LdCtrlDLDROPSWDownlink Switch for Shielding Forced Drop0To
re-visit OLC algorithmLdCtrlHSDSOVERLDTHRCommon Overload Threshold
for HS-DSCH(%)98LdCtrlDLALRMLDThreshold for Releasing from Downlink
Overload(%)85LdCtrlSWITCHTOFACHSwitch of Interactive
Class/Background Class RAB->FACH for Overload0To re-visit OLC
algorithmLdCtrlNFACHMaximum Users of Interactive Class/Background
Class RAB->FACH for Overload5LdCtrlULMAXFORHONUMMaximum Number
of Uplink Forced Handover Users Every
Time5LdCtrlDLFORCEHANDOFFSWDownlink Switch for Shielding Forced
Handover0To re-visit OLC algorithmLdCtrlULDECRATESWUplink Switch
for Shielding Rate Reduction1LdCtrlDECGBRSWSwitch for Shielding GBR
Reduction Shared by Uplink and Downlink0LdCtrlULDROPSWUplink Switch
for Shielding Forced Drop0To re-visit OLC
algorithmLdCtrlULALRMLDThreshold for Releasing from Uplink
Overload(dB)57.0To re-visit OLC
algorithmLdCtrlDLSERIOUSOVERLDDownlink Serious Overload
Threshold(%)100LdCtrlFORCEDHOSWITThe Switch of Forced Handover for
Online Users in Congestion0To re-visit OLC
algorithmLdCtrlULOVERLDUplink Common Overload Threshold(dB)61.0To
re-visit OLC algorithmLdCtrlULSERIOUSOVERLDUplink Serious Overload
Threshold(dB)62.0To re-visit OLC
algorithmLdCtrlDLMAXFORHONUMMaximum Number of Downlink Forced
Handover Users Every Time3LdCtrlDLDNMAXSTGMaximum Number of
Degraded Downlink Load Steps Every
Time1LdCtrlHSDSRECOVERTHRThreshold for Releasing from HS-DSCH
Overload(%)96LdCtrlULDNMAXSTGMaximum Number of Degraded Uplink Load
Steps Every Time1LdCtrlDLADJUSTMFPSWMaximum FACH Power Adjustment
Switch for MBMS Downlink Load Control1LdCtrlAGLLDDECAlgorithm of
Load Decreasing1LdCtrlREQUIREDRDSWITSwitch of Required Rate
Decreasing for Online Users in
Congestion0PrachPERMITMAXASCPermitted Maximum Access Service
Class3PrachDYNPSTLEVELINITInitial Dynamic Persistence
Level1PrachPSFNUMPersistence Scaling Factor
Number1PrachPRACHTYPEType of PRACH PreamblePrachCONSTVALPRACH
Initiation Tx Power Constant Value(dB)-23PrachASUBCHNUMAssigned
Subchannel No.[15@15@15]PrachMAXRACHTXPWRMaximum Allowed UL TX
Power of RACH(dBm)24PrachAVAILSUBCHANNUMPRACH Available Subchannel
Number4095PrachASIGENDIDXAvailable Signature End
Index[15@15@15]PrachPREAMTHSDetected Preamble
Threshold(dB)-21.0PrachSIB5ORSIB6Broadcast in either SIB5 or
SIB60PrachASIGSTIDXAvailable Signature Begin
Index[0@0@0]PrachRACHCTCIDRACH Common Transport Channel
ID65PrachMAXPREAMRETRANSMaximum Number of Preamble Being
Transmitted36PrachSIGNATUREAvailable
Signature65535PrachPSFPersistence Scaling
Factor[0.9]PrachMMAXMaximum Number of Preamble Ramping
Cycles6PrachPREAMSCRACODEPRACH Preamble Scrambling
CodePrachPRSTEPPRACH Preamble Power Ramp
Step(dB)1PrachAC2ASCMAPAC-to-ASC Mapping[0@0@0@0@0@0@0]
version3G RAN Parameter Baseline V1.0 20131011INTERNALVersionDateDescriptionBy1.011-Oct-13First Version.
Tables included:CelSel, CHspa, cnInfo, drbc, GloAc, Hspa, iuCnst, LdCtrl, nodeB, Prach PriSel, QosSeg, rncBRnc, rncFunction, rncLocRnc, ueCnst, utranCell
Most baseline values filled in except several (highlighted red) that require further study, revisit, or potential trials to identify best value.Khoo Nee Sern