Upload
phamtruc
View
215
Download
1
Embed Size (px)
Citation preview
TECHNICAL DATA MAINS VOLTAGE MODELS
• Extract Volume : 80 m3/h • Sound Volume* : 26.0dB (A)@3m • Voltage : 230-240v AC~ • Frequency : 50 Hz • Wattage : 35W • Max. Temp. : 50 ºC • Weight : 1.1 kg • Max Pressure : 150 pa
Double Insulated
* : Independent Tests 14-7-2003
DIMENSIONS
CURZON - 100mm CENTRIFUGAL FANS
SELV MODELS
TECHNICAL DATA SELV MODELS
Transformer • Input Voltage : 230-240v AC~ • Output Voltage : 12v AC~
Fan • Input Voltage : 12v AC~
• Extract Volume : 72 m3/h • Sound Volume : 29.4dB (A)@3m • Frequency : 50 Hz • Wattage : 44W • Max. Temp. : 50 ºC • Weight : 2.0 kg (Combined)
• Max Pressure : 125 pa
CU
RZO
N -
100
mm
CEN
TRIF
UG
AL F
ANS
A
B
Ø
C Measured in mm A : 216 B : 195 C : 50 D : 52 E : 98 Ø** : 80/100 * (80mm without adaptor—
100mm with adaptor)
The SELV models of the Curzon Centrifugal range are designed for use within the bath / shower areas and are fitted with long life 12v AC~ motors. The low voltage supply is from a transformer which is supplied with each SELV model ordered. The SELV models are available with over-run timer or humidistat & timer.
Transformers should be located outside the splash zone but all fans are suitable for siting within this area. The Curzon fan can be sited up to 8 metres from the transformer
PERFORMANCE GRAPH For
CURZON CENTRIFUGAL
0 20 40 60 70 80 90 m3/h
Pa 140
120
100
80
60
40
20
0
PERFORMANCE GRAPH For
CURZON CENTRIFUGAL SELV
Pa
140
120
100
80
60
40
20
0 0 20 40 60 70 m3/h
D
E
25
High Performance Levels 80m3/h (22 l/s) BEAB Approved IP24 Rated Humidity Versions Now Fitted With
“Intelligent” Humidistat Control Boards Integral Back Draught Shutters
Mains Voltage and SELV Models Available
Surface Mount or In-Line Models Available
3 Year Replacement Warranty on All Models
SPECIFICATION & INSTALLATION OVERVIEW
CU
RZO
N - 100
mm C
EN
TRIFU
GA
L FAN
S
Code Model
CUR 7001B Standard CUR 7002B Pull - cord CUR 7003B Over - run Timer CUR 7004B Humidistat & Timer CUR 7005B Timer & PIR CUR 7006B Humidistat, Timer & PIR CUR 9003LV SELV Single Speed - Over-run Timer CUR 9004LV SELV Single Speed – Humidistat & Timer
CUR 501A Fire Shutter Back Plate (1 Hour Rated)
CUR 7001BKIT In Line Version - Standard CUR 7003BKIT In Line Version - Timer
The Silavent Curzon range of fans are ideal for bathrooms and toilets where longer duct runs are required. Made from high gloss ABS, these fans produce an impressive pressure performance required to extract air along longer ducting runs and are capable of extracting up to 80m3/h. Easy to install, the Curzon fans are built to the highest quality with the motor mounted on rubber bushes for quietness and long life.
This range of fans is designed for wall or ceiling fixing and for use with all Silavent 100mm duct and flatduct. It can also be used in conjunction with an integral fire shutter back plate which is rated to 1 hour (FLA501A). The pull cord model is not suitable for ceiling mounting.
The humidistat versions are now fitted with the new “Intelligent” electronic humidity controls which work as intelligent humidistat. Unlike traditional humidity controls which trigger when humidity reaches a pre-set level, the “Intelligent” board reacts to a significant rate of change in a location’s humidity level - See Mayfair Range for full explanation of how “Intelligent” controls operate.
The in-line versions of the CURZON are designed to provide a powerful centrifugal fan to fit out of sight within the roof area. Giving the same performance as the surface mounted version, this model is ideal for use with the Silavent SPOTVENT shower light products.
PRODUCT SUMMARY
MODELS AVAILABLE
26
“Intelligent” Humidity Controls Fitted
to Humidistat Models
CURZON - 100mm CENTRIFUGAL FANS
TECHNICAL DATA MAINS VOLTAGE MODELS
• Extract Volume : 70 m3/h (HIGH) : 43m3/h (LOW) • Sound Volume* : 22.0dB (A)@3m(HIGH) : 12.0dB (A)@3m(LOW) • Voltage : 230-240v AC~ • Frequency : 50 Hz • Wattage : 35W (HIGH) • : 20W (LOW) • Max. Temp. : 50 ºC • Weight : 1.7 kg (FAN ONLY) • Max Pressure : 105 pa
Double Insulated
* : Independent Tests 14-7-2003
For Single Sped Models, Use Higher Extract Figures
DIMENSIONS
MAYFAIR - SERIES 70 CENTRIFUGAL FANS M
AYFA
IR -
SER
IES
70
CEN
TRIF
UG
AL F
ANS
A
A
0 10 20 30 40 50 60 70 m3/h
Pa
105
90
75
60
45
30
15
0
PERFORMANCE GRAPH For
MAYFAIR SERIES 70 CENTRIFUGAL
FAN OPERATION
Ø
D E
27
Measured in mm A : 250 C : 115 D : 40 E : 80 F : 115 Ø : 85 (FAN)
C
SINGLE SPEED
Standard : Single Speed Fan operated by separate light switch / remote switch (not supplied)
Pull Cord : Single Speed Fan is operated by integral pull cord
Timer : Single Speed Fan operated by separate light switch / remote switch (not supplied). The integral adjustable timer allows the fan to continue operating up to 25 minutes after being switched off
Humidistat : Single Speed Fan. Manual and Automatic operation. The “Intelligent” Humidity Control (IHC) works on detection of a significant change in the rate of increase in humidity levels. Whilst traditional humidistat controls wait for the humidity to reach a pre-set level, IHC detects a significant increase in a location’s humidity level and activates the extract fan immediately. Once the humidity is reduced, the integral adjustable timer allows the fan to continue operating for between 2 minutes and 25 minutes. This fan is operated by separate light switch / remote switch (not supplied)
Infra Red : The fan is activated by movement within the detection area of up to 5 metres. When movement is no longer detected, the integral adjustable timer allows the fan to continue operating for between 2 minutes and 25 minutes
TWIN SPEED
Standard : Twin Speed Fan designed to operate continuously at low speed. High speed is activated by separate light switch / remote switch (not supplied)
Timer : As the standard model but incorporates an integral adjustable timer. The timer will operate for between 2 minutes to 25 minutes after the switch has been turned off and the fan will return to running at the low speed. This fan is operated by separate light switch / remote switch (not supplied)
Humidistat : Single Speed Fan. Manual and Automatic operation. The “Intelligent” Humidity Control (IHC) works on detection of a significant change in the rate of increase in humidity levels. Whilst traditional humidistat controls wait for the humidity to reach a pre-set level, IHC detects a significant increase in a location’s humidity level and activates the extract fan immediately. Once the humidity is reduced, the integral adjustable timer allows the fan to continue operating for between 2 minutes and 25 minutes. This fan is operated by separate light switch / remote switch (not supplied)
Recessed or Surface Fixing on Wall / Ceiling
(In-Line Option Also Available) Integral Back Draught Shutters (SINGLE SPEED FANS ONLY)
BEAB Approved
Extract Rate 70m3/h (20 l/s) (HIGH SPEED)
43m3/h (12 l/s) (LOW SPEED) IPX4 Rated Plug In Fan Design -
Ideal For Large Building Projects “Intelligent” Humidistat Technology
3 Year On-Site Warranty on All Models
SPECIFICATION & INSTALLATION OVERVIEW
MAY
FAIR
- SE
RIE
S 70 C
EN
TRIFU
GA
L FAN
S
Code Model
MSS 070B Single Speed - Standard MTD 070B Single Speed - Over - run Timer MPC 070B Single Speed - Pull Cord MCC 070B Single Speed - Humidistat & Pull Cord MIR 070B Single Speed - Timer & PIR
MTS 070B Twin Speed - Continuous Trickle With Boost MTT 070B Twin Speed - Continuous Trickle With Boost & Timer MCT 070B Twin Speed - Humidistat, Timer & Pull Cord
The Mayfair Series 70 is designed to be installed in 2 parts—the building in frame first to reduce initial installation costs and on-site damage, followed by a plug-in fan body which allows easy maintenance and replacement. This is a system used effectively over the past 40 years by Silavent and proves to be highly effective on large building projects. The unit is constructed of high gloss ABS with a motor mounted on rubber bushes to provide high pressure performance combined with an impressive quietness.
PRODUCT SUMMARY
MODELS AVAILABLE
RECESSED FITTING USE
MAY 905B
SURFACE MOUNTING
(REMOVE FAN MOTOR DOME COVER) USE
MAY 504A
IN-LINE MOUNTING
(NOT PIR, HUMIDISTAT MODELS) USE
MAY 908B
CEILING MOUNTING
(With 225mm x 25mm Flatduct) USE
FLA 105A
CEILING MOUNTING
(With 110mm x 54mm Flatduct) USE
PFL 420A
WASHABLE FILTER COVER
(NOT PIR, HUMIDISTAT MODELS) USE
MAY 901A
28
“Intelligent” Humidity Controls Fitted
to Humidistat Models
MAYFAIR - SERIES 70 CENTRIFUGAL FANS
TECHNICAL DATA MAINS VOLTAGE MODELS
• Extract Volume : 97 m3/h (HIGH) : 50m3/h (LOW) • Sound Volume* : 32.0dB (A)@3m(HIGH) : 12.0dB (A)@3m(LOW) • Voltage : 230-240v AC~ • Frequency : 50 Hz • Wattage : 50W (HIGH) • : 20W (LOW) • Max. Temp. : 50 ºC • Weight : 1.7 kg (FAN ONLY) • Max Pressure : 150 pa
Double Insulated
* : Independent Tests 14-7-2003
For Single Speed Models, Use Higher Extract Figures
DIMENSIONS
MAYFAIR - SERIES 100 CENTRIFUGAL FANS M
AYFA
IR -
SE
RIE
S 1
00 C
EN
TRIF
UG
AL F
AN
S
A
A
0 20 40 60 70 80 90 100 m3/h
Pa
140
120
100
80
60
40
20
0
PERFORMANCE GRAPH For
MAYFAIR SERIES 100 CENTRIFUGAL
SINGLE SPEED
Standard : Single Speed Fan operated by separate light switch / remote switch (not supplied)
Pull Cord : Single Speed Fan is operated by integral pull cord
Timer : Single Speed Fan operated by separate light switch / remote switch (not supplied). The integral adjustable timer allows the fan to continue operating up to 25 minutes after being switched off
Humidistat : Single Speed Fan. Manual and Automatic operation. The “Intelligent” Humidity Control (IHC) works on detection of a significant change in the rate of increase in humidity levels. Whilst traditional humidistat controls wait for the humidity to reach a pre-set level, IHC detects a significant increase in a location’s humidity level and activates the extract fan immediately. Once the humidity is reduced, the integral adjustable timer allows the fan to continue operating for between 2 minutes and 25 minutes. This fan is operated by separate light switch / remote switch (not supplied)
Infra Red : The fan is activated by movement within the detection area of up to 5 metres. When movement is no longer detected, the integral adjustable timer allows the fan to continue operating for between 2 minutes and 25 minutes
TWIN SPEED
Standard : Twin Speed Fan designed to operate continuously at low speed. High speed is activated by separate light switch / remote switch (not supplied)
Timer : As the standard model but incorporates an integral adjustable timer. The timer will operate for between 2 minutes to 25 minutes after the switch has been turned off and the fan will return to running at the low speed. This fan is operated by separate light switch / remote switch (not supplied)
Humidistat : Single Speed Fan. Manual and Automatic operation. The “Intelligent” Humidity Control (IHC) works on detection of a significant change in the rate of increase in humidity levels. Whilst traditional humidistat controls wait for the humidity to reach a pre-set level, IHC detects a significant increase in a location’s humidity level and activates the extract fan immediately. Once the humidity is reduced, the integral adjustable timer allows the fan to continue operating for between 2 minutes and 25 minutes. This fan is operated by separate light switch / remote switch (not supplied)
FAN OPERATION
Ø
D E
29
Measured in mm A : 250 C : 115 D : 40 E : 80 F : 115 Ø : 85 (FAN)
C
Recessed or Surface Fixing on Wall / Ceiling
(In-Line Option Also Available) Integral Back Draught Shutters (SINGLE SPEED FANS ONLY)
BEAB Approved
Extract Rate 97m3/h (27 l/s) (HIGH SPEED)
50m3/h (14 l/s) (LOW SPEED) IPX4 Rated Plug In Fan Design -
Ideal For Large Building Projects “Intelligent” Humidistat Technology
3 Year On-Site Warranty on All Models
SPECIFICATION & INSTALLATION OVERVIEW
MAY
FAIR
- SE
RIE
S 100 C
EN
TRIFU
GAL FA
NS
Code Model
MSS 100B Single Speed - Standard MTD 100B Single Speed - Over - run Timer MPC 100B Single Speed - Pull Cord MCC 100B Single Speed - Humidistat & Pull Cord MIR 100B Single Speed - PIR & Timer
MTS 100B Twin Speed - Continuous Trickle With Boost MTT 100B Twin Speed - Continuous Trickle With Boost & Timer MCT 100B Twin Speed - Humidistat, Timer & Pull Cord
The Mayfair Series 100 is designed to be installed in 2 parts—the building in frame first to reduce initial installation costs and on-site damage, followed by a plug-in fan body which allows easy maintenance and replacement. This is a system used effectively over the past 40 years by Silavent and proves to be highly effective on large building projects. The unit is constructed of high gloss ABS with a motor mounted on rubber bushes to provide high pressure performance combined with an impressive quietness.
PRODUCT SUMMARY
MODELS AVAILABLE
RECESSED FITTING USE
MAY 905B
SURFACE MOUNTING
(REMOVE FAN MOTOR DOME COVER)
USE MAY 504A
IN-LINE MOUNTING
(NOT PIR, HUMIDISTAT MODELS) USE
MAY 908B
CEILING MOUNTING
(With 225mm x 25mm Flatduct) USE
FLA 105A
CEILING MOUNTING
(With 110mm x 54mm Flatduct) USE
PFL 420A
WASHABLE FILTER COVER
(NOT PIR, HUMIDISTAT MODELS) USE
MAY 901A
30
“Intelligent” Humidity Controls Fitted
to Humidistat Models
MAYFAIR - SERIES 100 CENTRIFUGAL FANS
TECHNICAL DATA MAINS VOLTAGE MODELS
• Extract Volume : 140 m3/h • Sound Volume* : 40.0dB (A)@3m • Voltage : 230-240v AC~ • Frequency : 50 Hz • Wattage : 60W • Max. Temp. : 50 ºC • Weight : 1.7 kg (FAN ONLY) • Max Pressure : 175 pa
Double Insulated
* : Independent Tests 14-7-2003
DIMENSIONS
MAYFAIR - SERIES 140 CENTRIFUGAL FANS M
AYFA
IR -
SE
RIE
S 1
40 C
ENTR
IFU
GA
L FA
NS
A
A
Measured in mm A : 250 C : 115 D : 40 E : 80 F : 115 Ø : 85 (FAN)
0 40 80 120 160 m3/h
Pa
175
150
125
100
75
50
25
0
PERFORMANCE GRAPH For
MAYFAIR SERIES 140 CENTRIFUGAL
Standard : Single Speed Fan operated by separate light switch / remote switch (not supplied) Pull Cord : Single Speed Fan is operated by integral pull cord Timer : Single Speed Fan operated by separate light switch / remote switch (not supplied). The integral adjustable timer allows the fan to continue operating up to 25 minutes after being switched off Humidistat : Single Speed Fan. Manual and Automatic operation. The “Intelligent” humidity control (IHC) works on detection of a significant change in the rate of increase in humidity levels. Whilst traditional humidistat controls wait for the humidity to reach a pre-set level, IHC detects a significant increase in a location’s humidity level and activates the extract fan immediately. Once the humidity is reduced, the integral adjustable timer allows the fan to continue operating for between 2 minutes and 25 minutes. This fan is operated by separate light switch / remote switch (not supplied) Infra Red : Single Speed Fan activated by movement within the detection area of up to 5 metres. When movement is no longer detected, the integral adjustable timer allows the fan to continue operating for between 2 minutes and 25 minutes
FAN OPERATION
Ø
D E
31
C
Recessed or Surface Fixing on Wall / Ceiling Integral Back Draught Shutters
Extract Rate 140m3/h (39 l/s)
IPX4 Rated Plug In Fan Design -
Ideal For Large Building Projects “Intelligent” Humidistat Technology
3 Year On-Site Warranty on All Models
SPECIFICATION & INSTALLATION OVERVIEW
MAY
FAIR
- SE
RIE
S 140 C
EN
TRIFU
GAL FAN
S
Code Model
MSS 140B Single Speed - Standard MTD 140B Single Speed - Over - run Timer MPC 140B Single Speed - Pull Cord MCC 140B Single Speed - Humidistat & Pull Cord MIR 140B Single Speed - PIR & Timer
The Mayfair Series 100 is designed to be installed in 2 parts—the building in frame first to reduce initial installation costs and on-site damage, followed by a plug-in fan body which allows easy maintenance and replacement. This is a system used effectively over the past 40 years by Silavent and proves to be highly effective on large building projects. The unit is constructed of high gloss ABS with a motor mounted on rubber bushes to provide high pressure performance combined with an impressive quietness.
PRODUCT SUMMARY
MODELS AVAILABLE
RECESSED FITTING USE
MAY 905B
SURFACE MOUNTING
USE FLA 106A
IN-LINE MOUNTING
NOT AVAILABLE
ON SERIES 140
CEILING MOUNTING
(With 225mm x 25mm Flatduct) USE
FLA 105A
CEILING MOUNTING
(With 110mm x 54mm Flatduct) USE
PFL 420A
WASHABLE FILTER COVER
(NOT PIR, HUMIDISTAT MODELS) USE
MAY 901A
32
“Intelligent” Humidity Controls Fitted
to Humidistat Models
MAYFAIR - SERIES 140 CENTRIFUGAL FANS
TECHNICAL DATA MAINS VOLTAGE MODELS
• Extract Volume : 79 m3/h (HIGH) : 36 m3/h (LOW) • Sound Volume : 38.8dB (A)@3m(HIGH) : 16.8dB (A)@3m(LOW) • Voltage : 230-240v AC~ • Frequency : 50 Hz • Wattage : 35W (HIGH) : 20W (LOW) • Max. Temp. : 50 ºC • Weight : 1.5 kg (FAN ONLY) • Max Pressure : 70 pa
Double Insulated
DIMENSIONS
MAYFAIR CLASSIC - CENTRIFUGAL FANS M
AYFA
IR C
LAS
SIC
- C
EN
TRIF
UG
AL
FAN
S
A
A
Measured in mm A : 197 B : 98.5 Ø : 80
0 20 40 60 70 80 90 m3/h
Pa
70
60
50
40
30
20
10
0
PERFORMANCE GRAPH For
MAYFAIR CLASSIC CENTRIFUGAL
SINGLE SPEED
Standard : Fan operated by separate light switch / remote switch (not supplied)
Timer : Fan operated by separate light switch / remote switch (not supplied). The integral adjustable timer allows the fan to continue operating up to 25 minutes after being switched off
TWIN SPEED Timer : Fan designed to operate continuously at low speed. High speed is activated by separate light switch / remote switch (not supplied). The integral adjustable timer allows the fan to continue operating at high speed up to 25 minutes after being switched off before reverting to the lower speed
FAN OPERATION
33
Ø
Recessed Fan,
Available With Fire Rated With Integral Shutter Variable Spigot Position
Extract Rate 79m3/h (22 l/s) IPX4 Rated Thermal Overload Protection
Maintenance Free Ball Bearing Motor
Motor Mounted On Rubber Bushes -
Significantly Reduces Vibration 3 Year On-Site Warranty on All Models
SPECIFICATION & INSTALLATION OVERVIEW
MAY
FAIR
CLA
SS
IC - C
EN
TRIFU
GA
L FAN
S
Code Model
MAY 102B Single Speed - Standard MAY 202B Single Speed - Over - run Timer MAY 402B Twin Speed - Over - run Timer MAY 502A Fire Shutter - 1 Hour Fire Rated - Gravity - Wall Installation MAY 502S Fire Shutter - 1 Hour Fire Rated - Spring - Wall/Ceiling Installation MAY 907A Building In Frame - 1 Hour Fire Rated
The Mayfair Classic is one of Silavent’s most successful products spanning over 40 years and still very popular in the marketplace. The centrifugal fan is in two parts, a fire protected building in frame that reduces initial cost and a plug-in fan body with fire shutters fitted. This design offers proven ease of maintenance and replacement. This centrifugal fan offers impressive pressure performance making it ideal for the longer duct runs.
PRODUCT SUMMARY
MODELS AVAILABLE
WALL FITTING USE MAY907A
CEILING FITTING USE MAY907A MAY 907A View From Back
MAY 907A View From Front
34 MAYFAIR CLASSIC - CENTRIFUGAL FANS
TECHNICAL DATA MAINS VOLTAGE MODELS
• Extract Volume : 90 m3/h • Sound Volume* : 38dB (A)@3m • Voltage : 230-240v AC~ • Frequency : 50 Hz • Wattage : 38W • Max. Temp. : 50 ºC • Weight : 1.3 kg • Max Pressure : 108 pa
Double Insulated
* : Independent Tests 14-7-2003
DIMENSIONS
PVS 100 - 100mm BATHROOM CENTRIFUGAL FANS P
VS
100
- 1
00m
m B
ATH
RO
OM
CE
NTR
IFU
GA
L F
AN
S
A
A
Ø
C Measured in mm A : 230 B : 20 C : 105 Ø : 97
Standard : Single Speed Fan operated by separate light switch / remote switch (not supplied) Timer : Single Speed Fan operated by separate light switch / remote switch (not supplied). The integral adjustable timer allows the fan to continue operating up to 25 minutes after being switched off Humidistat / Timer : Single Speed Fan with a integral humidity control which switches the fan on if the humidity levels exceed the pre-set level above 50% RH. Once the humidity level is reduced, the adjustable timer continues to operate the fan for up to 25 minutes
FAN OPERATION
B
Pa
120
100
80
60
40
20
0 0 20 40 60 70 80 90 m3/h
PERFORMANCE GRAPH For
PVS 100 BATHROOM CENTRIFUGAL
35
High performance levels 90m3/h (25 l/s) IPX4 Rated Variable Spigot Position
Backdraught Shutters
Washable Air Inlet Filter fitted as Standard
Maintenance Free Motor with Thermal Protection
High Pressure Performance for Longer Duct Runs 2 Year Replacement Warranty on All Models
SPECIFICATION & INSTALLATION OVERVIEW
PV
S 100 - 100m
m B
ATHR
OO
M C
EN
TRIFU
GA
L FANS
Code Model
PVS 100BB Standard PVS 100TBB Over-run Timer PVS 100HTBB Humidistat & Timer
Made from white, fire retardant ABS, the PVS 100mm Bathroom Centrifugal fans are designed to produce high pressure performance to operate effectively over longer duct runs. The variable spigot position allows flexibility in the positioning of the fan and often allows the installer to position the discharge ducting close to the ceiling in any corner of the room and be able to fit the front cover correctly. These centrifugal fans are suitable for use with longer duct runs.
The case is made from a white, fire retardant ABS and includes a maintenance free motor with thermal protection. The fans are supplied with a washable air inlet filter as standard
PRODUCT SUMMARY
MODELS AVAILABLE
36 PVS 100 - 100mm BATHROOM CENTRIFUGAL FANS
TECHNICAL DATA MAINS VOLTAGE MODELS
• Extract Volume : 260 m3/h • Sound Volume* : 41dB (A)@3m • Voltage : 230-240v AC~ • Frequency : 50 Hz • Wattage : 88W • Max. Temp. : 50 ºC • Weight : 2.2 kg • Max Pressure : 363 pa
Double Insulated
* : Independent Tests 14-7-2003
DIMENSIONS
PVS 100 - 100mm KITCHEN CENTRIFUGAL FANS P
VS 1
00 -
100
mm
KIT
CH
EN
CEN
TRIF
UG
AL F
AN
S
A
A
Ø
C Measured in mm A : 265 B : 20 C : 115 Ø : 97
Standard : Single Speed Fan operated by separate remote switch (not supplied) Timer : Single Speed Fan operated by separate light switch / remote switch (not supplied). The integral adjustable timer allows the fan to continue operating up to 25 minutes after being switched off Humidistat : Single Speed Fan with a integral humidity control which switches the fan on if the humidity levels exceed the pre-set level above 50% RH. Once the humidity level is reduced, the fan switches off. This fan is operated by separate remote switch (not supplied) Humidistat / Timer: Single Speed Fan with a integral humidity control which switches the fan on if the humidity levels exceed the pre-set level above 50% RH. Once the humidity level is reduced, the adjustable timer continues to operate the fan for up to 25 minutes. This fan is operated by separate remote switch (not supplied)
FAN OPERATION
B
0 40 80 120 160 200 240 m3/h
PERFORMANCE GRAPH For
PVS 100 KITCHEN CENTRIFUGAL
Pa
400
350
300
250
200
150
100
50
0
37
High performance levels 260m3/h (72 l/s) IPX4 Rated Variable Spigot Position
Backdraught Shutters
Washable Air Inlet Filter fitted as Standard
Maintenance Free Motor with Thermal Protection
High Pressure Performance for Longer Duct Runs 2 Year Replacement Warranty on All Models
SPECIFICATION & INSTALLATION OVERVIEW
PV
S 100 - 100m
m K
ITCH
EN C
EN
TRIFU
GAL FAN
S
Code Model
PVS 100BK Standard PVS 100TBK Over-run Timer PVS 100HBK Humidistat PVS 100HTBK Humidistat & Timer
Made from high gloss white, fire retardant ABS, the PVS 100mm kitchen centrifugal fans are designed to produce high pressure performance to operate effectively over longer duct runs. The variable spigot position allows flexibility in the positioning of the fan and often allows the installer to position the discharge ducting close to the ceiling in any corner of the room and be able to fit the front cover correctly. These centrifugal fans are suitable for use with longer duct runs.
The fans are fitted with maintenance free motors incorporating thermal protection.
The fans are supplied with a washable air inlet filter as standard
PRODUCT SUMMARY
MODELS AVAILABLE
38 PVS 100 - 100mm KITCHEN CENTRIFUGAL FANS
TECHNICAL DATA MAINS VOLTAGE MODELS
• Extract Volume : 240 m3/h (HIGH) : 120m3/h (LOW) • Sound Volume* : 19.0dB (A)@3m(HIGH) : 12.0dB (A)@3m(LOW) • Voltage : 230-240v AC~ • Frequency : 50 Hz • Wattage : 90W • Max. Temp. : 50 ºC • Weight : 3.1 kg (FAN ONLY) • Max Pressure : 300 pa
Double Insulated
* : Independent Tests 14-7-2003
DIMENSIONS
KITCHENAIRE - CENTRIFUGAL FANS K
ITC
HEN
AIR
E -
CEN
TRIF
UG
AL F
ANS
A
B
Measured in mm A : 337 B : 294 C : 74 D : 121 Ø : 100
0 40 80 120 160 200 240m3/h
Pa
350
300
250
200
150
100
50
0
PERFORMANCE GRAPH For
KITCHENAIRE CENTRIFUGAL
SINGLE SPEED
Standard : Single Speed Fan operated by separate light switch / remote switch (not supplied) Pull Cord : Single Speed Fan is operated by integral pull cord
Timer : Single Speed Fan operated by separate light switch / remote switch (not supplied). The integral adjustable timer allows the fan to continue operating up to 25 minutes after being switched off TWIN SPEED Pull Cord : Twin Speed Fan is operated by the 3-position pull cord. The operation of the pull cord is Off, Low, Boost, Off Humidistat : Manual and Automatic operation. If humidity exceeds the pre-set level above 50% RH, the fan switches to low speed. The pull cord offers a manual boost facility to high speed operation.
FAN OPERATION
Ø
C
C
D
39
Integral Back Draught Shutters & Integral Filter Extract Rate 240m3/h (67 l/s)
IP23 Rated Thermal Overload Protection
Maintenance Free Ball Bearing Motor
Motor Mounted On Rubber Bushes -
Significantly Reduces Vibration 3 Year On-Site Warranty on All Models
SPECIFICATION & INSTALLATION OVERVIEW
KITC
HE
NA
IRE
- CE
NTR
IFUG
AL FAN
S
Code Model
KIT 102B Single Speed - Standard KIT 103B Single Speed - Over - run Timer KIT 104B Single Speed - Pull Cord KIT 107B Single Speed - Humidistat & Pull Cord KIT 201B Twin Speed - Pull Cord KIT 203B Twin Speed - Humidistat
The Kitchenaire range of fans are, as the name implies, designed specifically for the kitchen area of the home. The large inlet grille provides a maximum area for extraction and filtration with the overall design of the product aimed to facilitate the removal and cleaning of the integral filter (ANC 303A). The Kitchenaire is a powerful, yet quiet, centrifugal fan made of high gloss ABS built with an exceptionally long life external rotor type motor with sealed for life ball bearings and thermal protection. It offers the ideal alternative to obtrusive cooker hoods. This range of fans can be wall or ceiling mounted and can be used in conjunction with Silavent range of flatduct. Please note that models fitted with a pull cord are not suitable for ceiling mounting.
PRODUCT SUMMARY
MODELS AVAILABLE
WALL FITTING HOLE SIZE 110mm USE ANC 841D
CEILING FITTING (With Flexible Ducting) HOLE SIZE 110mm
USE ANC503BT,ANC596
A etc
CEILING FITTING (With Flatduct)
INSTALL CEILING BOX USE FLA 007A
40 KITCHENAIRE - CENTRIFUGAL FANS