6
Z-E3726 DEVICE INSTALLATION MANUAL EN

2015-07-06 Z-E3726 DeviceInstallationManual EN RevA · This device installation manual applies to vehicle platforms appearing in the above compatibility list, ... MZone) 1 12 18-pin

  • Upload
    others

  • View
    1

  • Download
    0

Embed Size (px)

Citation preview

Z-E3726

DEVICE INSTALLATION MANUAL EN

2

COMPATIBILITY LIST

● The installation of the ZENEC system should be carried out by an authorized installer. Specific knowledge and tools are required to do the installation. Incorrect installation can cause damage to the vehicle and the ZENEC system.● Correct functioning can only be guaranteed when you use the ZENEC original accessories included in the kit or optionally available. The ZENEC system and the original accessories must under no circumstance be modified or altered in any way. Inappropriate actions can cause damage to the vehicle and the ZENEC system.

● Torx screwdriver T25● Phillips screwdriver● Release tool made of plastic● Hand saw or equivalent

● File● Hex key● Insulating tape

● The target vehicle must factory configured with preinstallation for a radio. The ZENEC system is not compatible with vehicles that are equipped with an OE radio or OE navigation system from the factory.● This device installation manual applies to vehicle platforms appearing in the above compatibility list, and in a condition as offered by the respective vehicle manufacturer. Other differing configurations and installations of motorhome manufacturers are not considered in this installation manual. If you have questions or vehicle-specific problems please contact the relevant motorhome manufacturer.● The ZENEC system is equipped with an integrated DAB+ receiver. To make use of this you will need a suitable DAB antenna (not included in kit) that must be connected to the ZENEC system.● If the target vehicle is equipped with a multifunction steering wheel, in order to support the steering wheel remote functions a stalk interface accessory obtainable separately is required. ● Software updates to the ZENEC system are installed with a USB memory device. Therefore when fitting the system make sure that the USB connection of the ZENEC system will still be accessible later (installation of USB extension cable or USB hub). ● If you have questions or problems relating to the ZENEC system, please contact the dealer from whom you purchased it.

Model Model Version Model YearFIAT Ducato III 250/251 2006 – 2011FIAT Ducato III 250/251 2011 – 2014FIAT Ducato III 250/251 from 2014Citroën Jumper II 250/250D/250L from 2006Peugeot Boxer II 250/251 from 2006

TOOLS REQUIRED

No. Article Qty1 ZENEC system 12 Mounting frame 13 Phillips screws 44 Remote control 25 microSD card with adapter 1

6 GPS antenna 1

7 Bluetooth microphone 1

THE KIT INCLUDES8 Antenna adapter ISO/DIN 1

9 Main connection cable 1 10 USB extension cable 111 24-pin connection cable (4.2, Cam, MZone) 112 18-pin connection cable (Mic, Cam) 113 Connection cable parking brake 114 Metal plate for GPS antenna 115 Double-sided adhesive pad 1

CAUTION

NOTE

3

1

2.a

2.b

3

REMOVAL WORK AND PREPARATION:

1. Remove both storage compartments in accordance with the manufacturer‘s information.

INSTALLATION:

2.a Cut off the left and right plastic holders for the storage compartments as flush as possible.

3. Remove the two original Torx screws at the top (T25).

2.b Use a suitable saw to do this, and then a file to remove any protrusions still present.

4

5.a

4

5.b

5.a Insert the mounting frame (No. 2) at an angle from above into the radio slot.

6. (No picture) Fit the GPS antenna (No. 6) at a suitable place,

and make sure that the GPS reception is not adversely affected due to shadowing by metallic vehicle parts (thermal glazing etc.). Use the metal plate supplied as a base for the GPS antenna to improve its reception, depending on the situation. Next run the connecting cable to the radio slot.

7. (No picture) If you wish to use it, now fit the external

Bluetooth microphone (No. 7) supplied, and run the connecting cable to the radio slot.

Depending on preference and on choice of an external or device-internal microphone, the microphone source for the Bluetooth mode must be correspondingly changed in the device menu.

8. (No picture) Run the USB extension cable (No. 10) from the

radio slot to the position you want.

4. Before installing the ZENEC system (No. 1) remove the two transport securing screws.

5.b Screw down the mounting frame at the top and bottom with the four Phillips screws (No. 3) supplied with the ZENEC system kit.

5

10

9

10. Connect all the cables to the ZENEC system (No. 1): those previously run in the radio slot, and the original antenna cable. If necessary, use the ISO DIN antenna adapter (No. 8)

included in the kit.

Next slide the ZENEC system carefully into the radio slot until it is heard to engage.

COMMISSIONINGMake sure that the vehicle is outside, and that the GPS reception is not adversely affected by any shadowing (trees, high buildings etc.). Now insert the navigation software SD card (No. 5) supplied into the SD card slot of the ZENEC system, and start it in order to establish a sat fix. Make sure that the vehicle is not moved until the sat fix is established. Now press the NAV button to start the navigation mode, and choose map view. Once your present location can be seen in the map view the sat fix will be automatically established. This can take 3 to 5 minutes. You can now use the ZENEC system.

Finally carry out a general functional test, and make the basic settings. Also ensure that no fault warnings appear on the vehicle side.

9. Connect the main cable (No. 9) of the ZENEC system (No. 1) to the ISO plug connectors of the vehicle.

● Make sure that all connectors at the rear of the unit have sufficient room and are not bent.● For vehicles with an original FIAT active antenna, it is necessary to ensure a power supply for the antenna. Pay particular attention that the plug connectors of the P.ANT lead of the main connection cable (No. 9) are connected together.● Connectors without a retaining mechanism must also be secured with insulating tape.

NOTE

E C C DA

A

BB C

amer

a

Rev

erse

Spe

ed In

IR In

ext.

Mic

Pow

er 3

00m

AG

ND

Aud

io In

CV

BS

In

CV

BS

In

Line

In R

Line

In L

Vide

o In

Fron

t Out

R

Fron

t Out

L

Rea

r Out

R

Rea

r Out

L

SU

B ( 4

.2)

CN

T ( 5

.1) O

ut

Sub

woo

fer O

ut

Vide

o O

ut 1

Vide

o O

ut 2

Line

Out

R

Line

Out

L

P. C

NTR

Par

king

Rev

erse

A/V

In

Line

Out

M-Z

one

*1 *1 *2 *2

Tech

nica

l mod

ifica

tions

exc

epte

d. N

o lia

bilit

y ac

cept

ed fo

r prin

ting

erro

rs.

© C

opyr

ight

201

5 · R

evA

/ cop

y de

adlin

e: Q

3-20

15 ·

Eng

lish

ZENEC · Bohrturmweg 1 · CH-5330 Bad Zurzach · Schweiz/Switzerland · Mail: [email protected] · www.zenec.com

B9 Loudspeaker rear right (-)B10 Loudspeaker rear right (+)B11 Loudspeaker front right (-)B12 Loudspeaker front right (+)B13 Loudspeaker front left (-)B14 Loudspeaker front left (+)B15 Loudspeaker rear left (-)B16 Loudspeaker rear left (+)

B1 N.A.B2 N.A.B3 KL 30 / Constant +12V PWR B4 N.A.B5 IlluminationB6 Switched +12V antenna PWRB7 KL 31 / Power GNDB8 KL 15 / Switched +12V PWR

B2B1

B4B3

B6B5

B8B7

B9B10

B11B12

B13B14

B15B16

A9 Loudspeaker rear right (+)A10 Loudspeaker front right (+)A11 Loudspeaker right (-)A12 Loudspeaker front right (-)A13 Loudspeaker rear left (+)A14 Loudspeaker front left (+)A15 Loudspeaker rear left (-)A16 Loudspeaker front left (-)

A1 KL 31 / Power GNDA2 KL 30 / Constant +12V PWR A3 KL 15 / Switched +12V PWRA4 IlluminationA5 Switched +12V amp PWR*A6 ParkingA7 Switched +12V antenna PWRA8 Reverse gear

*300mA max.

A10 A12 A14 A16A2 A4 A6 A8

A9 A11 A13 A15A1 A3 A5 A7

CONNECTION DIAGRAM

*1 Internally connected*2 Internally connected

(see note on DAB antenna page 2)A

C

AM/FM

DAB

GPS

D E

Input (see

OperatingManual„Input”)