20110210 Ai Die Casting Manual

8/13/2019 20110210 Ai Die Casting Manual

1/12

AI DIE CASTINGUsers Manual2010.12.

http://www.xavis.co.kr


2/12

X-rayAutomaticVision Inspection System

1. RUN AUTO INSPECTION Run AUTO INSPECTION.

1. Menu [Mode] [Inspection Mode]

2. Open the [Inspection Mode]


3/12


2. AUTO INSPECTION [AUTO INSPECTION] explain if had setting model file.

1. Fix the samples on the ZIG at designated areas.

2. Run [Inspection Mode].

3. Change [Effect Control] [Adjust.] [AUTO_G].


4/12


2. AUTO INSPECTION4. Setting the camera control as

5. Click X-ray on and set Voltage and Current for inspection.

If change inspection voltage and current, Click and save inspection vol. and cur. .

6. After find the brightness of image automatically,

[Image effect] [Control brightness] [NONE].


5/12


2. AUTO INSPECTION7. Click button to open setting area on [Auto Inspection].

8. Open the set model before. Click button at [Auto

Inspection].

9. Click the file that you want to see and

Click button. Open the requireddata like imagebeside.


6/12


2. AUTO INSPECTION10-1.Want to inspect the image that showing case.

Grab the image that want to inspect, and Clickat [Auto Inspection]

10-2. Want to inspect the image thatsaved before case. Click at [Auto Inspection]

and open the images.

11. Click , if opened setting valueand the image that you want to inspect.


7/12


2. AUTO INSPECTION12. Inspect distance of Die-casting.

Reference articles 1Control brightness of Image effect; No need

to do every time below.[AUTO_G] [NONE] because, this is for

finding suitable brightness value. But thecondition is changed, then need to do.

Reference articles 2Can inspect other image even though, the

setting value is open. Just click afteropen the saved image.


8/12


2. AUTO INSPECTION Explanation of inspection display picture.

Area of resultmark

Area of workindicationArea of

inspectionsetting


9/12


3. A.I MODEL SETTING A.I MODEL SETTING means explanation of setting button.

LOAD MODELOpen thedesignatedsetting value.

SAVE MODELSave settingvalue as youwant (location,name,,)

SAVE X-RAYSave the designated X-rayvoltage and current value atloading setting model.

It is useful to get images withsame value and condition.

SAVE DIRDesignate folders location of allsaved images at[AUTO INSPECTION].

Save as folder for saveimages with click button.

Open ImageOpen Image

RESULT MODEMark that wantduring inspect.


10/12


4. A.I SETTING PARAMETER A.I SETTING PARAMETER is explain the meaning of setting

parameter.

DETECT2Pixel value ofinsideboundarysurface.

DETECT1Pixel value ofoutsideboundarysurface.

Gap MinAcceptableminimumdistance.

Gap MaxAcceptablemaximumdistance.

PARAMETERDesignate applicable brightness value each parts.

Applicable brightness value is ; Check pixel value with click[Image Control] [Pix.]

ROI SETTINGPossiblesetting Qty ofinspectionarea.(max.10 EA)

Detect1.Pixel value of

outside

boundarysurface.

Detect2.Pixel value of

inside boundarysurface.

GapDistancebetween

Detect1 andDetect2.

GAP

SCALE MAXPixel value ismore thanscale max.In that case,it set the pixelvalue at 255.

SCALE MINPixel value isless than scalemin.In that case, itset the pixelvalue at 0.


11/12


5. SAVE INSPECTION IMAGE Save image and inspection result.

1. Designate the folder that will be saved with click button.

2. After designate image file name and file type at [Save

Inspection Result] click button.

3. Will be saved with image and inspection result value as the

image beside.


12/12


Thank you.

Documents

20110210 Ai Die Casting Manual