Upload
others
View
7
Download
1
Embed Size (px)
Citation preview
1
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
SPIRAL ROUND DUCT SYSTEMSTA M B E M E T A L P R O D U C T S
nergy Efficient
ost less to install
ften requires less space
eeds less hangers
peration costs lower
ore noise free
nstallation simplified
leaning less complicated
irflow measurements easier
ighter in weight
E
C
O
N
O
M
I
C
A
L
2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
Round Duct CONSTRUCTION STANDARDS TA M B E M E T A L P R O D U C T S
Spiral Seam Long. Seam Spiral Seam Long. Seam Spiral Seam Long. Seam
MAX DIAMETER
POSITIVE PRESSURE
6”8”10”12”14”16”18”
19-26”27-36”37-50”51-60”61-84”
282828282826262624222018
282826262624242422201816
282828282626242422201818
282826262424242220201816
282828262624242422201818
282626242422222220201816
+2” w.g. +4” w.g. +10” w.g.
Spiral Seam Long. Seam Spiral Seam Long. Seam Spiral Seam Long. Seam
MAX DIAMETER
NEGATIVE PRESSURE
–2” w.g. –4” w.g. –10” w.g.
6”7”8”9”10”11”12”13”14”15”16”17”18”19”20”21”22”23”24”
25-26”27-29”
30”31-33”
34”35-36”37-42”43-48”49-60”61-72”
2828282828282828282826262424242424242222222220202020201816
2828282828262626242424242222222020202020181818181616
18 A618 B4
282828282626262624242424242422222222222020202020201818
18 F618 F6
2828282626242424222222202020201818181818161616
20 A620 A618 B618 B616 B4
26262626262624242422222222222222222020201818181818
18 F1218 F618 F616 F4
26262624222222202020181818181818161616
18 A416 A416 B416 B416 B416 B4
An alphabet letter in the table means that reinforcement angles or their equivalent must be used at the foot interval following the letter. The angle sizes are:A = 1” x 1” x 1/8”; B = 1-1/4” x 1-1/4” x 3/16”; C = 1-1/2” x 1-1/2” x 3/16”; D = 1-1/2” x 1-1/2” x 1/4”; E = 2” x 2” x 3/16”; F = 2” x 2” x 1/4”If companion flange joints are used as reinforcements, those for 25” to 36” diameter shall be 1-1/2” x 1-1/2” x 3/16”; for 37” to 48” diameter 2” x 2” x 3/16”; for 40” to 60” diameter 2-1/2” x 2-1/2” x 3/16”; for 61” to 72” diameter 3” x 3” x 1/4”.
3
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
Round Duct CONSTRUCTION STANDARDS TA M B E M E T A L P R O D U C T S
Duct Diameter in inches Gauges Fittings
4 thru 8”9 thru 16” 18 thru 24”26 thru 32”34 thru 60”
26 Gauge24 Gauge22 Gauge20 Gauge18 Gauge
26 Gauge24 Gauge22 Gauge20 Gauge18 Gauge
POLYVINYL COATED DUCT GAUGES FOR UNDERGROUND DUCT AND FITTINGS
Duct Diameter in inches Gauges Fittings
4 thru 14”16 thru 26” 28 thru 36”38 thru 50”52 thru 60”
26 Gauge24 Gauge22 Gauge20 Gauge18 Gauge
26 Gauge24 Gauge22 Gauge20 Gauge18 Gauge
POLYVINYL COATED DUCT GAUGES FOR ABOVE GROUND DUCT AND FITTINGS
Spiral Gauge Seam
LongitudinalGauge Seam
Spiral Gauge Seam
LongitudinalGauge Seam
Duct Diameter in inches
POSITIVE PRESSURE
3 thru 8”9 thru 14” 15 thru 26”27 thru 36”37 thru 50”51 thru 60” 61 thru 84”
.025”
.025”
.032”
.040”
.050”
.063”N.A.
.032”
.032”
.040”
.050”
.063”
.071”
.090”
.025”
.032”
.040”
.050”
.063”N.A.N.A.
.040”
.040”
.050”
.063”
.071”
.090”N.A.
Maximum +2” w.g. Static Positive Maximum – 2” w.g. Static Negative
ALUMINUM ROUND DUCT GAUGE SCHEDULE
* Gauges equal or exceed SMACNA standards
4
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
Round Duct SEAMSTA M B E M E T A L P R O D U C T S
Available Gauges
Galvanized 28-16Stainless steel 26-22Aluminum 22-16Paint grip 26-16Poly vinyl coated 26-18Perforated 22
Galvanized 26-20Stainless steel 26-20Aluminum 22-20Paint grip 26-20Poly vinyl coated 26-18(button punched or rivited)
Galvanized 20-10Stainless steel 20-10Aluminum 18-1/4”Paint grip 20-10
Galvanized 26-18Stainless steel 26-22Aluminum 22-16Paint grip 26-18Poly vinyl coated 26-18
Spiral pipe lock seam (RL-1)(Corrugated 14” and larger for extra strength below grade)
Spiral pipe lock seam (RL-1)
Spot weld and bonded seam or continuous seam weld
Butt-welded seam
Gore locked seam
Spot weld or seam weld
Sealer
Sealer
6
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
345
67891011
12131415
161718192021222324
25262728293031
32333435363738
394041424344
454647484950
5254565860626466687072
PRESSED10 GA
1-1/4 X1-1/4 X1/8
1-1/2 X1-1/2 X1/8
1-1/2 X1-1/2 X3/16
2X2 X 3/16
3-1/164-1/165-1/16
6-1/87-1/88-1/89-1/810-1/811-1/8
12-3/1613-3/1614-3/1615-3/16
16-3/1617-3/1618-3/1619-3/1620-3/1621-3/1622-3/1623-3/1624-3/16
25-3/1626-3/1627-3/1628-3/1629-3/1630-3/1631-3/16
32-3/1633-3/1634-3/1635-3/1636-3/1637-3/1638-3/16
39-3/1640-3/1641-3/1642-3/1643-3/1644-3/16
45-3/1646-3/1647-3/1648-3/1649-3/1650-3/16
52-3/1654-3/1656-3/1658-3/1660-3/1662-3/1664-3/1666-3/16
9/329/329/32
3/83/83/83/83/83/8
7/16 7/16 7/16 7/16
7/16 7/16 7/16 7/16 7/16 7/16 7/16 7/16 7/16
7/16 7/16 7/16 7/16 7/16 7/16 7/16
7/16 7/16 7/16 7/16 7/16 7/16 7/16
7/16 7/16 7/16 7/16 7/16 7/16
7/16 7/16 7/16 7/16 7/16 7/16
7/16 7/16 7/16 7/16 7/16 7/16 7/16 7/16 7/16 7/16 7/16
666
666666
8888
888121212121212
16161616161616
16161616162424
242424242424
242424242424
2424242424242424242424
0.700.851.20
1.752.002.252.502.753.00
4.004.254.755.00
8.008.258.508.759.5010.2510.7511.2511.50
15.7516.5016.7518.0018.7519.5019.75
20.0021.2522.5022.7523.0023.7524.50
25.0025.7526.2526.5027.5028.00
28.5029.0030.0030.7531.5032.00
33.7535.0036.2537.5038.7540.0041.5042.7544.0045.2546.50
Round Duct CONNECTORS
TA M B E M E T A L P R O D U C T S
4-5/165-5/166-5/16
7-5/168-1/29-9/1610-5/811-13/1612-3/4
14151617
18192020 3/421-3/422-3/423-3/424-7/825-7/8
26-7/828-3/829-3/830-3/831-3/832-3/833-3/8
34-3/835-3/836-3/837-3/838-3/839-3/840-3/8
41-3/842-3/843-3/844-3/845-3/846-3/8
47-3/848-3/849-3/850-3/851-3/852-3/8
54-3/856-3/858-3/860-3/862-3/864-3/866-3/868-3/870-3/872-3/874-3/8
ORDER SIZE
ANGLE MILD STEEL
I.D. BOLT HOLES
HOLESIZE
BOLTCIRCLE
WEIGHTLBS.
Oval Angle Ring Dimensions
Vanstone Flange/Companion Flange
Companion Flange(Weld to Duct)
Angle Ring
Non-Extruding Gasket or Sealant
Bolts at Max.7” Intervals
3/8” Flange Turnedon Duct
D1
W1
D1 x W
1
L
F
t
8” typ. on the flat span
aMinor Axis
(inches)
3-5 5-11
12-14 16-18
19-24
25-36
37-50
Bolt HoleDiameter(inches)
9/32 3/8
7/16 7/16
7/16
7/16
7/16
Number ofBolts on
Curved Side
6 6
8 8
12
16
24
LxFNominal Size
(inches)
1 x 1 1-1/4 x 1-1/4
1-1/2 x 1-1/2 1-1/2 x 1-1/2
1-1/2 x 1-1/2
2 x 2
2 x 2
tNominal
Thickness
10 gauge 1/8”
1/8” 3/16”
3/16”
3/16”
3/16”
Standard Rings are hot rolled steel. Galvanized, aluminum, and stainless steel rings are also available.
Angle Iron Ring Specifications
Round Duct INSTALLATIONT A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
Installation of slip joint connectorsDuct-to-joint connections are made by using a duct coupling that slips inside the duct sections.
Duct-to-fitting connectionsDuct-to-fitting connections are made by slipping the fitting collar into the duct.
Fitting-to-fitting connectionsConnections can be made by using a short section of duct or by using a fitting coupling.
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
7
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
8
Round Duct MANIFOLDS/ASSEMBLIEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
Tambe Metal Products standard manifolds/assemblies of duct and fittingsWe offer manifolds/assemblies of duct and fittings from our standard duct and fitting components.
Manifolds/assemblies reduce field labor and potential sources of leakage by eliminating joints betweenpipe and standard fittings.
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
9
Underground INSTALLATION
TA M B E M E T A L P R O D U C T S
Rect. boot
Concrete Slope duct 1/8” per foot to sump
Plenum
Provide sump pump in high water areas
Concrete around entire sheet metal boot
Installation (As specified)
Diffuser
Concrete floor
Compacted earth
4” pea gravel or dry sand
Air duct
Sheet metal screws @ 6” OC.
Vapor barrier location for porous fill
Waterproof mastic
Watertable is below ductSubsoil drain pipe may be needed below duct in some areas
Vapor barrier location for concrete encasement
W = 11/2 D (Max.)H = 21/2 D (Max.)H = D/4 (Min.)
W
H
D
Pea gravel or sand fill for plastic coated duct. Encase entire duct in cement when using metal duct only
2-1/2”
10
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
Underground INSTALLATION
TA M B E M E T A L P R O D U C T S
Successive layer buildup
12 Ga. tie wireor 16 G. straps
PRECAUTION!Three stage placement of concrete is advisable to avoid damage and reduce danger of flotation. Concrete should never be dumped on the duct; cover should be moved laterally over the duct.
Floor surface elevation
Anchor spacing based on duct diameter
12” Concrete piers(Best for proper assembly of duct)
* This illustration is a design guide
Pre-poured base slab
Typical anchorage of ducts to be encased in concrete
2-1/2”3”
5”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
11
Approximate Weight SPIRAL DUCT In pounds per linear foot -- Based on galvanized steel
TA M B E M E T A L P R O D U C T S
DIAMETER 26 gauge
24 gauge
22 gauge
20 gauge
18 gauge
16 gauge
WEIGHT PER FOOT
345678910111213141516171819202224262830323436384042444648505254565860
.761.021.281.541.792.052.312.572.823.083.343.593.844.114.364.634.895.155.656.166.677.187.718.228.729.279.7310.3010.7711.3511.8612.3612.8813.3913.9114.4214.9415.45
1.011.351.692.032.372.713.053.393.734.074.414.745.085.425.776.106.446.787.468.148.829.5010.1810.8411.5412.2012.8813.5614.2514.9115.5916.2616.6917.1218.0518.9819.6520.34
1.231.642.062.472.883.293.714.124.544.955.365.776.186.607.027.437.848.259.089.9110.7311.5612.3813.2114.0114.9015.6716.5017.3218.1618.9919.8220.6321.4422.2623.0823.9124.73
1.481.942.422.913.403.864.374.865.345.836.326.817.287.788.258.769.259.73
10.7111.6812.6613.6314.6015.5816.5117.5318.4619.4820.4021.4222.3923.3624.3325.3026.2827.2528.2329.20
3.884.525.175.826.477.117.758.489.059.7010.3411.0811.6412.2912.9314.2315.5216.8218.1119.4120.7121.9723.2924.5125.8827.2128.4729.7731.0632.3733.6834.9836.2737.5638.84
4.765.586.347.187.928.729.5410.3111.0511.8012.6513.4714.3215.0915.8517.5019.0020.7022.2023.9025.5027.0828.8030.2631.7533.4735.0036.6538.3039.9441.5843.1844.7846.3847.97
Single Wall Round ELBOWST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
45º DIE STAMPED ELBOW3” DIA. THRU 12”
15º & 30º 2-PIECE ELBOW
E22/E45
2”
E60
E90
2”
R1
45º 3-PIECE ELBOW
2”
E45
90º DIE STAMPED ELBOW3” DIA. THRU 12”
E45
2”
R1 = D1
E45
2”
2”
2”
R1
60º 3-PC. ELBOW
E60
90º 5-PC. ELBOW 45º 3-PIECE ELBOW
E90
2”
2”
2”
E15/E30
E45
D1
D1
R1 = D1
R1
D1
D1
D1
R1
D1
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
12
90º 3-PC. ELBOW WITHSTRAIGHT LATERAL
R1
4”
2”
D1
D2
4”
D1
2”
45º 2-PC. ELBOW WITHSTRAIGHT LATERAL
E290/EV290 E90L
E45L
Single Wall Round ELBOWST A M B E M E T A L P R O D U C T S
D1 No. ofvanes
3-9
10-14
15-19
20-60
≥60
2
3
4
5
Max 12”spacing
90º 2-PC. ELBOW
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
R1
2”
D1
2”
2”
E45R
45º 3-PC. ELBOWWITH REDUCER
90º 5-PC. ELBOWWITH REDUCER
E90R
R1
D2L
2”
D1 L = D1 – D2
6” Minimum
D1
2”
R1
L
D2
L = D1 – D2
6” Minimum
2”
2”
D2
With or without vanes.
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
13
Single Wall Round STRAIGHT TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
TEE
TEE CROSS
D1
4”
2” 2”
D3
D3 + 4”
L2”
2”
D4
L = D1 – D2
6” Minimum
D1
2”
4”
2” 2”
D3
D3 + 4” L2”
2”
D1
2”
4”
2” 2”
D2
D2 + 4” 2”2”
D1
4”
2” 2”
2”2”
D2
D3
D2 + 4”
T
TX
TR
TRX
REDUCING TEE
REDUCING TEE CROSS
D2 ≥ D3
L = D1 – D2
6” Minimum
D3 ≥ D4
D2
D2
2” 2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
14
Single Wall Round CONICAL TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
CONICAL TEE
CONICAL TEE CROSS
L = D1 – D2
6” Minimum
D1
D3 + 6” L2”
2”
D2D1
D2 + 6” 2”2”
CT
CTX
CTR
REDUCING CONICAL TEE
REDUCING CONICALTEE CROSS
CTRX
D1 D2 + 6”
2”
D1 D3 + 6”
L
2”
D2
D3 ≥ D4D2 ≥ D3
2” 2”
5” 1” 1”
D2
2” 2”
5” 1” 1”
D3
2” 2”
5” 1” 1”
D3L = D1 – D2
6” Minimum
1” 1”
D4
1” 1”
D3
2” 2”
5” 1” 1”
D2
2” 2”
2” 2”
2” 2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
15
Single Wall Round SHOE TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
SHOE TEE
SHOE TEE CROSS
ST
STX
STR
REDUCING SHOE TEE
REDUCING SHOETEE CROSS
STRX
D2 ≥ D3
L = D1 - D2
Minimum 6”
D1
2” 2” 2” 2”
D2 + X + 4”
D3 ≥ D4
D1
2” 2” 2”2”
D2 + X + 4”
2”
D2
X
2”
D2
X
D1
2” 2” 2” L
D3 + X + 4”
2”
D2
2”
D3
X
D1
2” 2” 2” L2”
D2
2”
D3
X
2”
D3
X
D4
X
2”
D3 + X + 4”
D3
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
D2
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
D3, D4
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
D2, D3
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
L = D1 - D2
Minimum 6”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
16
Single Wall Round STRAIGHT LATERALST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
45º LATERAL
L LR
45º REDUCING LATERAL
D1
2” 2”
(D2 x 1.414) + 4” 2”2”
2”
D2
4”
2” 2”
2”
D2D1
L= D1 – D2
6” Minimum
2” (D3 X 1.414) + 4”
2”
D3
4”
L
45º LATERAL CROSS
LX LRX
45º REDUCINGLATERAL CROSS
D1
2” 2”
(D2 X 1.414) + 4”
L = D1 – D2
6” Minimum
D3 ≥ D4D2 ≥ D3
2” 2”
2”
D2D1
2”
D2
4”
2”
D3
4”
2”
D3
4”
2”
D4
4”
(D3 X 1.414) + 4”
L2”
2”2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
17
D1
2”2”
4”
D26”
2”
Single Wall Round CONICAL LATERALST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
45º CONICAL LATERAL
45º CONICALLATERAL CROSS
L = D1 – D2
6” Minimum
CL
CLX
CLR
45º REDUCINGCONICAL LATERAL
45º REDUCING CONICALLATERAL CROSS
CLRX
D2 ≥ D3
D1
2”
2”2”
((D3 + 2”) X 1.414) + 4”
((D2 + 2”) X 1.414) + 4”
4”
D36”
2”
D2
L = D1 – D2
6” Minimum
D1
2”2”
2”2”
((D2 + 2”) X 1.414) + 4”
4”
D26”
2”
D1
2”
2”2”
D2
4”
D36”
2”
L
L
4”
D36”
2”
((D3 + 2”) X 1.414) + 4”
4”
D46”
2”
2”
2”
2”
D3 ≥ D4
2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
18
EC
Single Wall Round MISCELLANEOUST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
ECCENTRIC REDUCER
PC
FITTING COUPLING
FC
CONCENTRIC REDUCER
E45 RDERDC
PIPE COUPLING
D1
2” 2”
D1
2” 2”
END CAP
D1
2”
L = D1 – D2
6” MinimumL = 2 [D1 – D2]6” Minimum
RECTANGLE TOROUND
RTR
W1 x D1
D2
L
O1
TD
2”
D1 D2
2”L 2”
D1D2
2”L
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
19
Single Wall Round MISCELLANEOUST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
REDUCING BULL HEAD TEE With or without vanes.
E22/E45 E60
Y45
REDUCING Y BRANCH
YR45
E45 ROET
BULL HEAD TEE With or without vanes.BHT/BHTV
SET
BHTR/BHTRV
Y BRANCH
D2 D3
D1
2” 2”
2”
2”
2” 2”
D1 No. ofvanes
3-7
8-10
10-60
>60
1
3
5
Max 12”spacing
D1 + 4”2” 2”
2”2”2” 2”
2”
D1
OFFSET
D1
01
L
2”
D2 D3
D1
2”2”
2” 2”
2”2”
D1 + 4”
2"
2"2"
D3
2"
2"2" 2"
D1
D2
ROUND TO ROUND
D1
D2
L
TD
O1
L2 = D1 – D3
6” MinimumL1 = D1 – D2
6” Minimum
L1 L2
L2 = D1 – D3
6” MinimumL1 = D1 – D2
6” Minimum
L1 L2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
20
Shop/Field Installed ACCESSORIEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
CONICAL TAP
E22/E45 E60
TAP 45 STR
TAP
E45 CTAP 90
REGISTER TAP
RECTAP
TAP 90
ADOOR
Standard flange is 1/2”.2” saddle is also available.
LATERAL TAP
ACCESS DOOR
Standard flange is 1/2”.2” saddle is also available.
5”
D1
Standard flangeis 1/2”. 2” saddleis also available.
Standard flangeis 1/2”. 2” saddleis also available.
D1
4”
SHOE TAP D2
D1
D2
2”
4”
D1
D1
1/2” Flange
Flange in or out
D1
2”
D2
2”
L
1”
D2
3 thru 89 thru 16
17 thru 2627” and up
L5”7”10”13”
1”
D2 X W2
D2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
21
15º & 30º2-PIECE ELBOW
Double Wall Round ELBOWST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
45º DIE STAMPED ELBOW3” DIA. THRU 12”
E15/E30
60º 3-PC. ELBOW
E60
90º 5-PC. ELBOW
E90
45º 3-PIECE ELBOW
90º DIE STAMPED ELBOW3” DIA. THRU 12”
E45 E90 E45
2”
D1+2”
R1 = D1
D1
D1+2”
R1
2”2”
D1
E45
R1
2”
D1 + 2”D1
D1+2”
D1
R1
2”
D1 + 2”
2”
D1
R1
2”
D1
D1 + 2”
R1 = D1
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
22
45º 2-PC. ELBOW WITHSTRAIGHT LATERAL
90º 3-PC. ELBOW WITHSTRAIGHT LATERAL
E90L
E45L
Double Wall Round ELBOWST A M B E M E T A L P R O D U C T S
R1
4”
2”
D1
D1 + 2”
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
D1
D1 + 2”
4”
2”
D2 + 2”
R1
E45R
R1
D2L
2”
45º 3-PC. ELBOWWITH REDUCER
L = D1 – D2
6” MinimumD1 + 2”
D1
D2 + 2”
D2
90º 5-PC. ELBOWWITH REDUCER
L = D1 – D2
6” Minimum
E90R
2”
R1
L
D2 + 2”
D1
D1 + 2”
E290/EV290
90º 2-PC. ELBOW With or without vanes.
D1 No. ofvanes
3-9
10-14
15-19
20-60
≥60
2
3
4
5
Max 12”spacing
2”
D1
2”
2”
D1 + 2”
2”
D2
2”
D2 + 2”
D2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
23
D1 + 2”
D1 D2
D2 + 2”
D3
D3 + 2”
D3
D3 + 2”
D1 + 2”
D1
D2
D2 + 2”
D1 + 2”
D1
D2
D2 + 2”
Double Wall Round STRAIGHT TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 fax
TEE
TEE CROSS
L = D1 – D2
6” Minimum
2”
4”
2” 2”
D3 + 6” L2”
2”
2”
4”
2” 2”
2”2”
2”
4”
2” 2”
2”2”
D2 + 6”
T
TX
REDUCING TEE
REDUCING TEECROSS
TR
TRX
D4
D4 + 2”
D2
D2 + 2”
D3
D3 + 2”
D1 + 2”
D1
2”
4”
2” 2”
D3 + 6”
L2”
2”
D2 ≥ D3
L = D1 – D2
6” MinimumD3 ≥ D4
D2 + 6”
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 faxTAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
24
D1 + 2”
D1
D1 + 2”
D1 D2
D2 + 2”
D1 + 2”
D1 D2
D2 + 2”
D2
2”
5” 1” 1”
D2 + 2”
D1 + 2”
D1
Double Wall Round CONICAL TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
CONICAL TEE
CONICAL CROSS
D2 + 8” 2”2”
CT
CTX
REDUCING CONICAL TEE
REDUCING CONICALCROSS
CTR
CTRX
L = D1 – D2
6” Minimum
D3 + 8” L2”
2” 2”
L = D1 – D2
6” Minimum
D3 ≥ D4
2” 2”
D2 + 8”
D2 ≥ D3
2” 2”
D2
2”
5” 1” 1”
D2 + 2”
2”
D3
1” 1”
D3 + 2”
D3
2”
5” 1” 1”
D3 + 2”
L
2” 2”
D3
2”
5” 1” 1”
D3 + 2”
D4
1” 1”
D4 + 2”
D3 + 8”
2”
2”
2”
2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
25
2”
D3 + 2”
D3
D1
D1 + 2”
D2
D2 + 2”
D3 + 2”
Double Wall Round SHOE TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
SHOE TEE
SHOE TEE CROSS
ST
STX
STR
REDUCING SHOE TEE
REDUCING SHOETEE CROSS
STRX
D2 ≥ D3
L = D1 - D2
Minimum 6”
2” 2” 2” L
2”
D3 + X + 6”
2”
L = D1 - D2
Minimum 6”
D3 ≥ D4
D2 + 2”
D1
D1 + 2”
2” 2” 2” 2”
D2
D2 + X + 6”
Y
D1
D1 + 2”
2” 2” 2”
D3 + X + 6”
2”2” 2” 2”2”
D2 + X + 6”D1
D1 + 2”
2”
X X
D3
D2 + 2”
2”
X
D2
D2 + 2”D2
X
2”
X
D4 + 2”
D4
XL
D2
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
D2, D3
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
D3
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
D3, D4
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
D3 + 2”
D3
2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
26
D1 + 2”
D1
D2 + 2”
D2
D1 + 2”
D1
D2
D2 + 2”
D3
D3 + 2”
2” 2”
2”
4”
2”
4”
D3
D3 + 2”
D2 + 2”
D2
D1 + 2”
D1
2” 2”
2”
L = D1 – D2
6” Minimum
2”
4”
L
D2
D2 + 2”
D1 + 2”
D1
((D2 + 2”) x 1.414) + 4”) 2”2”
4”
Double Wall Round STRAIGHT LATERALST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
45º LATERAL
45º LATERAL CROSS
L
LX
LR
LRX
45º REDUCING LATERAL
45º REDUCING LATERAL CROSS
2”
L = D1 – D2
6” Minimum
D3 ≥ D4D2 ≥ D3
2” 2”
2” 2”
2”
L
D3
D3 + 2”2”
4”
D4
D4 + 2”2”
4”
2”
((D2 + 2”) x 1.414) + 4”)
((D3 + 2”) x 1.414) + 4”)
((D3 + 2”) x 1.414) + 4”)
2”2”
2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
27
D2
D2+2”
D1 + 2”
D1
Double Wall Round CONICAL LATERALST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
45º CONICAL LATERAL
45º CONICALLATERAL CROSS
L = D1 – D2
6” Minimum
CL
CLX
CLR
45º REDUCINGCONICAL LATERAL
45º REDUCING CONICALLATERAL CROSS
CLRX
L = D1 – D2
6” Minimum
D3 ≥ D4D2 ≥ D3
2”2”
2”2”
((D2 + 4”) X 1.414) + 4”
D2 + 2”
D2
D1 + 2”
D1
L
2”
2”
2”2”
((D3 + 4”) X 1.414) + 4”
D3
D3+2”
D1 + 2”
D1
2”2”
((D2 + 4”) X 1.414) + 4”
4
D2 + 2”
D2
D1 + 2”
D1
L2”
2”
2”2”
((D3 + 4”) X 1.414) + 4 ”
4”
6”
2”
D3
D3+2”
4”
6”
2”
D2
D2+2”
4”
6”
2”
D3
D3+2”
4”
6”
2”
6”
2”
4”
D4
D4+2”6”
2”
4”2”2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
28
D1+2”
2” 2”L
D1+2”
D2+2”D2
2” 2”L
Double Wall Round MISCELLANEOUST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
D1
ECCENTRIC REDUCER
PC
FITTING COUPLING
FC
CONCENTRIC REDUCER
E45 RDERDC
EC
L = 2 [D1 – D2]6” Minimum
L = D1 – D2
6” Minimum
PIPE COUPLING
2” 2” 2” 2”
END CAP
D1
D2+2”
D2
D1
D1
D1
2”
W1 x D1
L
D2
D2+2”
[W1 +2”]x[D1+2”]
RECTANGLE TOROUND
RTR
O1
TD
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
29
D2
D2+2”
D2+2”
REDUCING BULL HEAD TEE With or without vanes.
Double Wall Round MISCELLANEOUST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
E22/E45
Y45
REDUCINGY BRANCH
YR45
OFFSET
E45 ROET
BHT/BHTV
SET
BHTR/BHTRV
Y BRANCH
D1+2”
01
L
2”
D1 No. ofvanes
3-7
8-10
10-60
>60
1
3
5
Max 12”spacing
D1
D3+2”D2 D3
D1
2”2”
2” 2”
2”2”
D1+2”
D2 D3
D1
2” 2”
2”2”
2” 2”
D2+2” D3+2”
D1+2”
D1 + 6”2” 2”
2”2”2” 2”
2”
D1
D1+2”
D3+2”
D1 + 6”
2"
2"2"
D3
2"
2"2" 2"
D1
D1+2”
ROUND TO ROUND
L2 = D1 – D3
6” MinimumL1 = D1 – D2
6” Minimum
L1 L2
BULL HEAD TEE With or without vanes.
L2 = D1 – D3
6” MinimumL1 = D1 – D2
6” Minimum
L1 L2
D1+2”
D2
L
TD
O1
D2+2”
D1
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
30
D2
D2+2”
D2
D2+2”
Shop/Field Installed ACCESSORIEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
CONICAL TAP
E22/E45 E60
TAP 45 STR
TAP
E45 CTAP 90
REGISTER TAP
RECTAP
TAP 90
ADOOR
Standard flange is 1/2”.2” saddle is also available.
LATERAL TAP
ACCESS DOOR
Standard flange is 1/2”.2” saddle is also available.
D1
Standard flangeis 1/2”. 2” saddleis also available.
Standard flangeis 1/2”. 2” saddleis also available.
SHOE TAP
D1
D1
1/2” Flange
Flange in or out
D1
2”
D1
4”
D1+2” D1+2”
D2
2”
L
D1
D2+2”
2”
4” 5”
1” 1”
D2
3 thru 89 thru 16
17 thru 2627” and up
L5”7”10”13”
D2 X W2
D2
D2+2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
31
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
1
OVAL DUCT SYSTEMSTA M B E M E T A L P R O D U C T S
Flat oval duct combines the advantages of round duct and rectangular duct because it may fit in spaces where there is not enough room for round duct, and it can be joined using the techniques of round duct assembly.
Spiral flat oval duct is machine-made from round spiral lockseam duct and is available in varying sizes and aspect ratios. It can be made with longitudinal seams.
Flat oval duct has considerably less flat surface that is susceptible to vibration and requires less reinforcement than a corresponding size of rectangular duct. The deflec-tion of the flat oval duct under pressure is related to the flat span rather than the overall width of the duct.
Any round duct fitting can have an equivalent fitting made in flat oval. As in rectangular duct, a hard bend elbow denoted the plane of the duct width, whereas an easy bend elbow denotes the bend in the plane of the duct height. Any branch fitting can be made with the branch tap either round or flat oval. The tap of the flat oval fitting can be located anywhere on the circumference of the fitting body. If the diameter of a round tap is greater than the height of the flat oval body, a transition can be made from flat oval to round, providing an equivalent area at the base of the transition.
Flat oval duct is for positive pressure applications only unless special designs are used.
2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
INITIAL SPIRAL SIZE
Oval Duct CONSTRUCTION STANDARDSTA M B E M E T A L P R O D U C T S
1516171819202224262830323436384042444648505254565860626466687072
2022232526283134374144475053565963666972
22242527303336394246495255586165687174
21232426293235384145485154576063677073
2021232528313437404347505356596265697275
1920222327303336394245495255586164677174
192122252932353841444751545760636669737679
2124273134374043464953565962656871757881
23262933363942454851555861646770737780
2528313538414447505357606366697275798285
27303337404346495255596265687174778184
323539424548515457616467707376798386
3437414447505356596366697275788185
3639434649525558616568717477808387
3841454851545760636770737679828589
4043475053565962656972757881848791
4245495255586164677174778083868993
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
M I N O R A X I S
MA
JO
R A
XIS
Major Dimension Duct Width
SpiralSeam Duct
Gauge
LongitudinalSeam Duct
Gauge
Gauge of Fittings
FLAT OVAL DUCT CONSTRUCTION
to 24”25 to 36”37 to 48”49 to 60”61 to 70”
71” and up
242222202018
202018181616
202018181616
* Initial spiral sizes indicated are for fabrication purposes only. For conversion from rectangular or round to oval, consult factory.
*
Nominal flat oval pipe sizes
3
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
INITIAL SPIRAL
SIZE
Oval Duct CONSTRUCTION STANDARDSTA M B E M E T A L P R O D U C T S
1516171819202224262830323436384042444648505254565860626466687072
20.1421.7123.2824.8526.4227.9931.1334.2737.4240.5643.7046.8449.9853.1256.2759.4162.5565.6968.8371.87
22.1423.7125.2826.8529.9933.1336.2739.4242.5645.7048.8451.9855.1258.2761.4164.5567.6970.8373.97
21.0022.5724.1425.7128.8531.9935.1338.2741.4244.5647.7050.8453.9857.1260.2763.4166.5569.6972.83
19.8521.4223.0024.5727.7130.8533.9937.1340.2743.4246.5649.7052.8455.9859.1262.2765.4168.5571.6974.83
18.7120.2821.8523.4226.5729.7132.8535.9939.1342.2745.4248.5651.7054.8457.9861.1264.2767.4170.5573.69
19.1420.7122.2825.4228.5731.7134.8537.9941.1344.2747.4250.5653.7056.8459.9863.1266.2769.4172.5575.6978.83
21.1424.2827.4230.5733.7136.8539.9943.1346.2749.4252.5655.7058.8461.9865.1268.2771.4174.5577.6980.83
23.1426.2829.4232.5735.7138.8541.9945.1348.2751.4254.5657.7060.8463.9867.1270.2773.4176.5579.69
25.1428.2831.4234.5737.7140.8543.9947.1350.2753.4256.5659.7062.8465.9869.1272.2775.4178.5581.6984.83
27.1430.2833.4236.5739.7142.8545.9949.1352.2755.4258.5661.7064.8467.9871.1274.2777.4180.5583.69
32.2835.4238.5741.7144.8547.9951.1354.2757.4260.5663.7066.8469.9873.1276.2779.4182.5585.69
34.2837.4240.5743.7146.8549.9953.1356.2759.4262.5665.7068.8471.9875.1278.2781.4184.55
36.2839.4242.5745.7148.8551.9955.1358.2761.4264.5667.7070.8473.9877.1280.2783.4186.55
38.2841.4244.5747.71
40.2843.4246.5749.7152.8555.9959.1362.2765.4268.5671.7174.8477.9881.1284.2787.4190.55
42.2845.4248.5751.7154.8557.9961.1364.2767.4270.5673.7076.8479.9883.1286.2789.4192.55
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
MINOR AXIS
MAJOR AXIS
Actual flat oval pipe sizes
4
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
Single wall slip fit1. The fittings are male sized to slip into the pipe section. A good tight fit is necessary for minimalizing friction loss and good sealing. Care should be taken during handling to avoid any dents or distortions that can cause improper fit and difficult installation.
2. A sharp blow to the top of the collar with hand or sheet metal mallet can cause the collar to seat into the duct. For larger sized duct, straddle the duct and slightly compress duct sideways while another person jiggles the fitting into the duct.
3. As a last resort, a half moon cut on the top of the collar to eliminate the “high-spot” and the fitting slips easily into place.
Double wall slip fitThe inner and outer collars of fittings are male sized and designed to slip into the connecting duct. The inner collar projects beyond the outer collar permitting the inner collar to be started into the inner liner of the duct section similar to the single wall technique.
1. Bring bottom of inner collar into the duct section at a slight angle.
2. Using slight pressure, work the rest of the collar into the duct.
3. When the inner collar is fully started into the duct, start the outer collar in the same manner. Tilt the bottom edge slightly upon insertion and tap the “high-spots” to work the collar into the duct.
It is suggested to save time, sub-assemblies be made on the floor then hoisted into place.
Additional suggestions for installation1. Rest your duct on two blocks of wood and then using your hands and moving the duct, in an up and down motion, will help you make your connection without damaging the duct.
2. Allowances have already been made in fittings for installation. Should a kink occur through handling, by carefully straightening out the kinks and bends a good connection can still be made.
3. DO NOT use a hammer and screwdriver to make a connection. The possibility of causing damages internally is a real danger to friction loss. Apply pressure with the heel of your hand or a good thump with your fist can help the fitting slip into the duct.
4. Apply duct sealant to the internal end of the spiral approximately 1” and apply duct sealant around the slip part of your fitting. As the fitting slips into the spiral duct the sealant will not scrape off in the slip connection.
5. Whenever possible brush your internal joint to make it smooth inside and out; also, inspect your sealed joints for coverage. One to two days after completing the connections check connections for shrinkage of the duct sealant. Reapply sealant where needed.
Oval Duct INSTALLATIONTA M B E M E T A L P R O D U C T S
5
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
Oval Duct REINFORCEMENTTA M B E M E T A L P R O D U C T S
Double trapeze reinforcement and hanger for oval duct
Flat span reinforcement with internal tie rods for oval duct
See the following 4 pages for size and spacing of reinforcement. Reinforcement schedules are shown for 2”, 3’, 4’, and 6” W.G. systems.
6
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
INITIAL SPIRAL
SIZE
Oval Duct REINFORCEMENTTA M B E M E T A L P R O D U C T S
1516171819202224262830323436384042444648505254565860626466687072
B8/20C8/22C8/23C6/25C8/26D8/28E8/31E6/34F5/37F5/41F4/44F4/47H5/50H5/53H4/56H4/59G3/63G3/66H3/69I4/72
NR/19B8/21B8/22C8/24C10/25C8/27D8/30E8/33E6/36F5/39F5/43F4/46F4/49H5/52H5/55H4/58H4/61G3/65G3/68H3/71I4/74
NR/18NR/19NR/21B8/23B8/24C10/26C8/29D8/32E8/35E6/38F5/41F5/45F4/48G5/51H5/54H5/57H4/60H4/63G3/67G3/70I4/73
NR/17NR/18NR/20NR/21NR/23D8/25C10/28C8/31D8/34E8/37E6/40F5/43F5/47G5/50G5/53H5/56H5/59H4/62H4/65G3/69I5/72I5/75
NR/16NR/17NR/19NR/20NR/22NR/23NR/27C1O/30C8/33D8/36E8/39E6/42F5/45F5/49G5/52G5/55H5/58H5/61H4/64H4/67G3/71I5/74
NR/18NR/19NR/21NR/22NR/25NR/29C10/32C8/35D8/38E8/41E6/44F5/47F6/51GS/54GS/57H5/60H5/63H4/66H4/69I5/73I5/76I5/79
NR/21NR/24NR/27NR/31C10/34C8/37D8/40E8/43E6/46F6/49F6/53G5/56G5/59H5/62H5/65H4/68H5/71I5/75I5/78I4/81
NR/26NR/29NR/33C10/36C8/39D8/42E8/45E6/48F6/51F6/55G5/58G5/61H5/64H5/67H4/70H5/73I5/77I5/80
NR/28NR/31NR/35C10/38C8/41D8/44E8/47E8/50F6/53F6/57G5/60G5/63H5/66H5/69H5/72H5/75I5/79I5/82I4/85
NR/30NR/33NR/37C10/40C8/43D8/46E10/49E8/52F6/55F6/59G5/62G5/65H5/68H5/71H5/74H5/77I5/81I5/84
NR/32NR/35NR/39C10/42C8/45D8/48E10/51E8/54F6/57F6/61G5/64G5/67H5/70H5/73H5/76H5/79I5/83I5/86
NR/34NR/37NR/41C10/44C8/47D10/50E10/53E8/56F6/59F6/63G5/66G5/69H6/72H5/75H5/78H5/81I5/85
NR/36NR/39NR/43C10/46C8/49D10/52E10/55E8/58F6/61F6/65G5/68G5/71H6/74H5/77H5/80H5/83I5/87
NR/38NR/41NR/45C10/48C10/51D10/54E10/57E8/60F6/63F6/67G5/70G6/73H6/76H5/79H5/82H5/85I5/89
NR/40NR/43NR/47NR/50C10/53D10/56E10/59E8/62F6/65F6/69G6/72G6/75H6/78H5/81H5/84H5/87I5/91
NR/42NR/45NR/49NR/52C10/55D10/58E10/61E8/64F6/67F6/71G6/74G6/77H6/80H5/83H5/86H5/89I5/93
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
M I N O R A X I S
MA
JO
R A
XIS
2” W.G. Reinforcement
To use this table:1. Find the minor axis of the oval size you wish to reinforce in the first row.2. Go down the column for that minor axis until you reach the major axis of the oval size you wish to reinforce.3. To the left of the major axis you will find the appropriate reinforcement.
7
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
INITIAL SPIRAL
SIZE
Oval Duct REINFORCEMENTTA M B E M E T A L P R O D U C T S
1516171819202224262830323436384042444648505254565860626466687072
B8/20C6/22C6/23D6/25D6/26E6/28E6/31F5/34F4/37F4/41G4/44G4/47H4/50H4/53H3/56H3/59H3/63H3/66I3/69I3/72
NR/19B8/21B8/22C6/24D8/25D6/27E6/30E6/33F5/36F4/39F4/43G4/46 G4/49H4/52H4/55H3/58H3/61H3/65H3/68I3/71I4/74
NR/18NR/19NR/21B8/23B8/24C8/26D6/29E6/32E6/35F5/38F4/41F4/45G4/48H5/51H4/54H4/57H3/60H3/63H3/67H3/70I3/73
NR/17NR/18NR/20NR/21NR/23B8/25C8/28D6/31E6/34E6/37F5/40F4/43F4/47H5/50H5/53H4/56H4/59H3/62H3/65H3/69I4/72I4/75
NR/16NR/17NR/19NR/20NR/22NR/23C8/27C8/30D6/33E6/36E6/39F5/42F4/45F4/49H5/52H5/55H4/58H4/61H3/63H3/67H3/71I4/74
NR/18NR/19NR/21NR/22NR/25C8/29C8/32D6/35E6/38E6/41F5/44F4/47G5/51H5/54H5/57H4/60H4/63H3/66H3/69I4/73I4/76I3/79
NR/21NR/24NR/27C8/31C8/34D6/37E6/40E6/43F5/46G5/49G5/53H5/56H5/59H4/62H4/65H3/68I5/71I4/75I4/78I3/81
NR/26NR/29C8/33C8/36D8/39E6/42E6/45F5/48G5/51G5/55H5/58H5/61H4/64H4/67H3/70I5/73I4/77I4/80
NR/28NR/31C8/35C8/38D6/41E6/44E6/47F6/50G5/53G5/57H5/60H5/63H4/66H4/69I5/72I5/75I4/79I4/82I3/85
NR/30NR/33C8/37C8/40D6/43E6/46E6/49F6/52G5/55G5/59H5/62H5/65H4/68I5/71I5/74I5/77I4/81I4/84
NR/32NR/35C8/39C8/42D6/45E6/48E6/51F6/54G5/57G5/61H5/64H5/67H4/70I5/73I5/76I5/79I4/83I4/86
NR/34NR/37C8/41C8/44D6/47E8/50E6/53F6/56G5/59G5/63H5/66H5/69I5/72I5/75I5/78I5/81I4/85
NR/36NR/39C8/43C8/46D6/49E8/52E6/55F6/58G5/61G5/65H5/68H5/71I5/74I5/77I5/80I5/83I4/87
NR/38NR/41C8/45C8/48D8/51E8/54E6/57F6/60G5/63G5/67H5/70H6/73I5/76I5/79I5/82I5/85I4/89
NR/40NR/43C8/47C8/50D8/53E8/56E6/59F6/62G5/65G5/69H6/72H6/75I5/78I5/81I5/84I5/87I4/91
NR/42NR/45C8/49C8/52D8/55E8/58E6/61F6/64G5/67G5/71H6/74H6/77I5/80I5/83I5/86I5/89I4/93
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
M I N O R A X I S
MA
JO
R A
XIS
3” W.G. Reinforcement
To use this table:1. Find the minor axis of the oval size you wish to reinforce in the first row.2. Go down the column for that minor axis until you reach the major axis of the oval size you wish to reinforce.3. To the left of the major axis you will find the appropriate reinforcement.
8
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
INITIAL SPIRAL
SIZE
Oval Duct REINFORCEMENTTA M B E M E T A L P R O D U C T S
1516171819202224262830323436384042444648505254565860626466687072
C5/20C5/22D5/23E5/25E6/26E5/28F5/31F5/34G4/37G4/41G3/44G3/47H3/50H3/53I3/56I3/59I3/63I3/66
C6/19C5/21C5/22C5/24D6/25E6/27E5/30F5/33F5/36G4/39G4/43G3/46 G3/49H3/52H3/55I3/58I3/61I3/65I3/68
I2.5/71J3/74
NR/18B6/19C6/21C5/23C5/24D6/26E6/29E5/32F5/35F5/38G4/41G4/45G3/48H4/51H3/54H3/57I3/60I3/63I3/67I3/70J3/73
NR/17NR/18NR/20B6/21C6/23C5/25D6/28E6/31E5/34F5/37F5/40G4/43G4/47H4/50H4/53H3/56H3/59I3/62I3/65I3/69H3/72H3/75
NR/16NR/17NR/19NR/20NR/22B6/23B8/27D6/30E6/33E5/36F5/39F5/42G4/45G4/49H4/52H4/55H3/58H3/61I3/64I3/67I3/71H3/74
NR/18NR/19NR/21NR/22NR/25B8/29D6/32E6/35E5/38F5/41F5/44G4/47H5/51H4/54H4/57H3/60H3/63I3/66I3/69H3/73H3/76J3/79
NR/21NR/24NR/27B8/31D6/34E6/37E5/40F5/43F5/46H5/49H5/53H4/56H4/59H3/62H3/65I3/68I4/71H3/75H3/78J3/81
NR/26NR/29B8/33D6/36E6/39E5/42F5/45F5/48H5/51H5/55H4/58H4/61H3/64H3/67I3/70I4/73H3/77H3/80
NR/28NR/31B8/35D6/38E6/41E5/44F5/47G6/50H5/53H5/57H4/60H4/63H3/66H3/69I4/72I4/75H3/79H3/82J3/85
NR/30NR/33B8/37D6/40E6/43E5/46F6/49G6/52H5/55H5/59H4/62H4/65H3/68I5/71I4/74I4/77H3/81H3/84
NR/32NR/35B8/39D6/42E6/45E5/48F6/51G6/54H5/57H5/61H4/64H4/67H3/70I5/73I4/76I4/79H3/83H3/86
NR/34NR/37B8/41D6/44E6/47E6/50F6/53G6/56H5/59H5/63H4/66H4/69I5/72I5/75I4/78I4/81H3/85
NR/36NR/39B8/43D6/46E6/49E6/52F6/55G6/58H5/61H5/65H4/68H4/71I5/74I5/77I4/80I4/83H3/87
NR/38NR/41B8/45D6/48E8/51E6/54F6/57G6/60H5/63H5/67H4/70I5/73I5/76I5/79I4/82I4/85H3/89
NR/40NR/43B8/47D8/50E8/53E6/56F6/59G6/62H5/65H5/69I5/72I5/75I5/78I5/81I4/84I4/87H3/91
NR/42NR/45B8/49D8/52E8/55E6/58F6/61G6/64H5/67H5/71I5/74I5/77I5/80I5/83I4/86I4/89H3/93
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
M I N O R A X I S
MA
JO
R A
XIS
4” W.G. Reinforcement
To use this table:1. Find the minor axis of the oval size you wish to reinforce in the first row.2. Go down the column for that minor axis until you reach the major axis of the oval size you wish to reinforce.3. To the left of the major axis you will find the appropriate reinforcement.
9
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
INITIAL SPIRAL
SIZE
Oval Duct REINFORCEMENTTA M B E M E T A L P R O D U C T S
1516171819202224262830323436384042444648505254565860626466687072
C4/20D4/22E4/23E4/25E5/26F5/28F4/31G4/34H3/37H3/41H2.5/44H2.5/47I2.5/50I2.5/53I2.5/56I2.5/59I2.5/63I2.5/66J2/69J2.5/72
C5/19C4/21C4/22D4/24E5/25E5/27F5/30F4/33G4/36H3/39H3/43H2.5/46H2.5/48I2.5/52I2.5/55I2.5/58I2.5/61I2.5/65I2.5/68J2/74J2.5/74
NR/18C5/19C5/21C4/23C4/24D5/26E5/29F5/32F4/35G4/38H3/41H3/45H2.5/48H3/51I2.5/54I2.5/57I2.5/60I2.5/63I2.5/67I2.5/70J2.5/73
NR/17NR/18NR/20C5/21C5/23C4/25D5/28E5/31E5/34F4/37G4/40H3/43H3/47H3/50H3/53I2.5/56I2.5/59I2.5/62I2.5/65I2.5/69J3/72J2.5/75
NR/16NR/17NR/19NR/20NR/22C5/23D5/27D5/30E5/33F5/36F4/39G4/42H3/45H3/49H3/52H3/55I2.5/58I2.5/61I2.5/64I2.5/67I2.5/71J3/74
NR/18NR/19NR/21NR/22B6/25D5/29D5/32E5/35F5/38F4/41G4/44H4/47H4/51H3/54H3/57I2.5/60I2.5/63I2.5/66I2.5/69J3/73J3/76J2.5/79
NR/21NR/24B6/27D5/31D5/34E5/37F5/40F4/43G4/46H4/49H4/53H3/56H3/59I2.5/62I2.5/65I2.5/68I3/71J3/75J3/78J2.5/81
NR/26B6/29D5/33D5/36E5/39F5/42F4/45G4/48H4/51H4/55H3/58H3/61I2.5/64I2.5/67I2.5/70I3/73J3/77J3/80
NR/28B6/31D5/35D5/38E5/41F5/44F4/47H5/50H4/53H4/57H3/60H3/63I2.5/66I2.5/69I3/72I3/75J3/79J3/82J2.5/85
NR/30B6/33D5/37D5/40E5/43F5/46G5/49H5/52H4/55H4/59H3/62H3/65I2.5/68I4/71I3/74I3/77J3/81J3/84
NR/32B6/35D5/39D5/42E5/45F5/48G5/51H5/54H4/57H4/61H3/64H3/67I2.5/70I4/73I3/76I3/79J3/83J3/86
NR/34B6/37D5/41D5/44E5/47F6/50G5/53H5/56H4/59H4/63H3/66H3/69I4/72I4/75I3/78I3/81J3/85
NR/36B6/39D5/43D5/46E5/49F6/52G5/55H5/58H4/61H4/65H3/68H3/71I4/74I4/77I3/80I3/83J3/87
NR/38B6/41D5/45D5/48F6/51F6/54G5/57H5/60H4/63H4/67H3/70I4/73I4/76I4/79I3/82I3/85J3/89
NR/40B6/43D5/45D6/50F6/53F6/56G5/59H5/62H4/65H4/69I4/72I4/75I4/78I4/81I3/84I3/87J3/91
NR/42B6/45D5/49D6/52F6/55F6/58G5/61H5/64H4/67H4/71I4/74I4/77I4/80I4/83I3/86I3/89J3/93
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
M I N O R A X I S
MA
JO
R A
XIS
6” W.G. Reinforcement
To use this table:1. Find the minor axis of the oval size you wish to reinforce in the first row.2. Go down the column for that minor axis until you reach the major axis of the oval size you wish to reinforce.3. To the left of the major axis you will find the appropriate reinforcement.
E45 EB
Single Wall Oval ELBOWST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
EASY BEND
E22/E45
60º 3-PC. ELBOW
E60
90º 5-PC. ELBOW
E90 E45
HARD BEND
E45
15º & 30º 2-PIECE ELBOW
45º 3-PIECE ELBOW
HB
E15/E30
W1 x D1
R1
2” 2”
R1
2”
R1
2”
R1
W1
D1
W1
D1
W1 x D1
W1 x D1W1 x D1
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
10
90º 3-PC. ELBOW WITHSTRAIGHT LATERAL
4”
2”
4”
2”
45º 2-PC. ELBOW WITHSTRAIGHT LATERAL
E90L
E45L
Single Wall Oval ELBOWST A M B E M E T A L P R O D U C T S
W1 x D1
W1 x D1
R1
R1
L90º 5-PC. ELBOWWITH REDUCER
2”L = W1 – W2
6” Minimum
E90R
W2 x D2
R1
W1 x D1
W1 x D1
E45R
45º 3-PC. ELBOWWITH REDUCER W2 x D2
R1
L
2”L = W1 – W2
6” Minimum
E290/EV290
2”
2”
2”
D1 No. ofvanes
3-9
10-14
15-19
20-60
≥60
2
3
4
5
Max 12”spacing
90º 2-PC. ELBOW
W1 x D1
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
W2 x D2
2”
2”
W2 x D2
With or without vanes.
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
11
Single Wall Oval STRAIGHT TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 fax
TEE
TEE CROSS
L = W1 – W2
6” Minimum
2”
4”
2” 2”
W3 + 4”
L2”
2”
L = W1 – W2
6” Minimum
2”
4”
2” 2”
L2”
2”4”
2” 2”
2”2”
2”
4”
2” 2”
2”2”
W2 + 4”
T
TX
TR
TRX
REDUCING TEE
REDUCING TEE CROSS
W3 x D3
W1 x D1
W3 + 4”
W2 x D2
W1 x D1
W2 x D2
W2 x D2
W4 x D4
W1 x D1
W3 x D3
W2 x D2
W1 x D1
W2 + 4”
W2 ≥ W3W3 x D3
W3 ≥ W4
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
12
Single Wall Oval CONICAL TEEST A M B E M E T A L P R O D U C T S
CONICAL TEE
CONICAL CROSS
L = W1 – W2
6” Minimum
L2”
2”
2”2”
CT
CTX
CTR
REDUCING CONICAL TEE
REDUCING CONICALTEE CROSS
CTRX
W2 + 6”
2”
W2 ≥ W3
W1 x D1
W2 + 6”
W1 x D1
W3 + 6”
W2 x D2
W3 ≥ W4
L = W1 – W2
6” Minimum
W2 x D2
1”
2” 2”
2”
5” 1” 1”
2” 2”
2”
5” 1”
W3 x D3
1”
2” 2”
2”
5” 1”
W2 x D2
L
2”
W2 x D2W1 x D1
1”
2” 2”
2”
5” 1”
W1 x D1
1”
2” 2”
1”
W3 x D3
1”
2” 2”
1”
W4 x D4
W3 x D3
W3 +6”
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
2” 2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
13
W3, W4
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
W1 x D1
2”
X2” 2”2” 2”
W2 x D2
Single Wall Oval SHOE TEEST A M B E M E T A L P R O D U C T S
SHOE TEE
SHOE TEE CROSS
ST
STX
STR
REDUCING SHOE TEE
REDUCING SHOETEE CROSS
STRX
W2 ≥ W3
L = W1 - W2
Minimum 6”
L
2”
2”
L = W1 - W2
Minimum 6”
W3 ≥ W4
W2 + X + 4”
W3 + X + 4”
W3 x D3
W2 x D2
W2 + X + 4”
W1 x D1
2”
X2” 2”2” 2”
W2 x D2
X
2”
W3 x D3
W1 x D1
2” 2”
L
2”
W1 x D1
2” 2”
W3 x D3
X
2”
W4 x D4
W2 x D2W3 + X + 4”
2”
XX
X X
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
W2
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
2”
W3
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
W2, W3
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
14
Single Wall Oval STRAIGHT LATERALST A M B E M E T A L P R O D U C T S
45º LATERAL
45º LATERAL CROSS
L = W1 – W2
6” Minimum
L2”
L
LX
LR
LRX
45º REDUCING LATERAL
45º REDUCINGLATERAL CROSS
(W3 X 1.414) + 4”(W2 X 1.414) + 4” 2”2”
L = W1 – W2
6” Minimum
W3 ≥ W4W2 ≥ W3
W3 x D3
2” 2”
2”
4”
W2 x D2W1 x D1
W2 x D2
2” 2”
2”
4”
W1 x D1
W2 x D2
2” 2”
2”
4”
W3 x D3
2”
4”
W1 x D1
L
W2 x D2W1 x D1
W3 x D3
2” 2”
2”
4”
W4 x D4
2”
4”
(W2 x 1.414) + 4” (W3 x 1.414) + 4”
2”
2”
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
2”2” 2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
15
Single Wall Oval CONICAL LATERALST A M B E M E T A L P R O D U C T S
45º CONICAL LATERAL
45º CONICAL LATERALCROSS
L = W1 – W2
6” Minimum
CL
CLX
CLR
45º REDUCINGCONICAL LATERAL
45º REDUCING CONICALLATERAL CROSS
CLRXL = W1 – W2
6” Minimum
W3 ≥ W4W2 ≥ W3
2”2”
2”2”
((W2 + 2”) X 1.414) + 4” L2”
2”
2”2”
((W3 + 2”) X 1.414) + 4”
W1 x D1
W2 x D2
W1 x D1
4”
6”
2”
4”
6”
2”
W3 x D3
W2 x D2
((W2 + 2”) X 1.414) + 4”
2”2”
W1 x D1
W2 x D2
4”
6”
2”
L2”
2”
2”2”
W1 x D1
4”
6”
2”
W3 x D3
W2 x D2
4”
6”
2”
W3 x D3
4”
6”
2”
W4 x D4
((W3 + 2”) X 1.414) + 4”
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
2” 2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
16
RECTANGLE TOROUND
Single Wall Oval MISCELLANEOUST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
ECCENTRIC REDUCER
PC
FITTING COUPLING
FC
CONCENTRIC REDUCER
E45 RDERDC
EC
PIPE COUPLING
2” 2” 2” 2”
END CAP2”
W1 x D1 W1 x D1
W1 x D1
W2 x D2 W1 x D1
L = W1 – W2
6” Minimum
2” 2”L
W2 x D2 W1 x D1
L = 2 [W1 – W2]6” Minimum
2” 2”L
W1 x D1
L
O1
TD
RTR
W2 x D2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
17
REDUCING BULL HEAD TEE With or without vanes.
Single Wall Oval MISCELLANEOUST A M B E M E T A L P R O D U C T S
E22/E45 E60
Y45
REDUCING Y BRANCH
YR45
OFFSET
E45 ROET
BULL HEAD TEE With or without vanes.BHT/BHTV
SET
BHTR/BHTRV
Y BRANCH
2” 2”
2”2”
2” 2”
D1 No. ofvanes
3-7
8-10
10-60
>60
1
3
5
Max 12”spacing
2” 2”
2”2”2” 2”
2”
W1 x D1
W1 x D1
W1 x D1
01
L
2”
W2 x D2
2”2”
2” 2”
2”2”
W3 x D3
W1 x D1
W2 x D2 W3 x D3
W1 + 4”
2"
2"2"
2"
2"2" 2"
ROUND TO ROUND
L2 = W1 – W3
6” MinimumL1 = W1 – W2
6” Minimum
L1 L2
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
L2 = W1 – W3
6” MinimumL1 = W1 – W2
6” Minimum
L1 L2
W1 x D1
W1 + 4”
L
TD
O1
W1 x D1
W2 x D2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
18
Shop/Field Installed ACCESSORIEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
RECTAP
CONICAL TAP
E22/E45
TAP
E45 CTAP 90
REGISTER TAP
TAP 90
ADOOR
Standard flange is 1/2”.2” saddle is also available.
ACCESS DOOR
Standard flange is 1/2”.2” saddle is also available.
1/2” Flange
Flange in or out 4”
D1
D2 x W2
W1
TAP 45 STR
LATERAL TAP
Standard flangeis 1/2”. 2” saddleis also available.
Standard flangeis 1/2”. 2” saddleis also available.
SHOE TAP
2”
4”
W1 x D1
2”
L
W1 x D1
W2xD2
D1
W1
4”
2” 4”
D1
D2 x W2 W1
W2
3 thru 89 thru 16
17 thru 2627” and up
L5”7”10”13”
D1
W1
1”
1”
2” 5”
D2 x W2
W2xD2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
19
15º & 30º2-PIECE ELBOW
Double Wall Oval ELBOWST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 fax
E15/E30
60º 3-PC. ELBOW
E60
90º 5-PC. ELBOW
E90
45º 3-PIECE ELBOW
E45
R1
2”2”
W1 x D1
E45
2”2”
W1
D1
W1
D1
EB
EASY BENDHARD BEND
HB
[W1+2”]x[D1+2”] W1 x D1
[W1+2”]x[D1+2”]
2”
W1 x D1
[W1+2”]x[D1+2”]
W1 x D1
[W1+2”]x[D1+2”]
R1
R1
R1
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 faxTAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
20
45º 3-PC. ELBOWWITH REDUCER
45º 2-PC. ELBOW WITHSTRAIGHT LATERAL
90º 3-PC. ELBOW WITHSTRAIGHT LATERALS
E290/EV290 E90L
E45L
Double Wall Oval ELBOWST A M B E M E T A L P R O D U C T S
90º 2-PC. ELBOW .
2”
4”
2”
D1 No. ofvanes
3-9
10-14
15-19
20-60
≥60
2
3
4
5
Max 12”spacing
2”
2”
2”
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
4”
2”
R1
W1 x D1
[W1+2”]x[D1+2”]
W1 x D
1
[W1+
2”]x[D1+
2”]
W1 x D1
[W1+2”]x[D1+2”]
R1
L
W2 x D2
90º 5-PC. ELBOWWITH REDUCER
E90R
2”
W1 x D1
[W1+2”]x[D1+2”]
[W2+
2”]x[D2+
2”]
L = W1 – W2
6” Minimum
L
W2 x D2
E45R
2”R1
W2 x D2
[W2+
2”]x[
D2+2”
]
[W2+2”]x[D2+2”]
L = W1 – W2
6” Minimum
R1
With or without vanes
W2 x D2
[W2+2”]x[D2+2”]
W2 x D2
[W2+2”]x[D2+2”]
2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
21
Double Wall Oval STRAIGHT TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
TEE
TEE CROSS
L = W1 – W2
6” Minimum
2”
4”
2” 2”
W3 + 6” L2”
2”
2”
4”
2” 2”
2”2”
2”
4”
2” 2”
2”2”
W2 + 6”
T
TX
REDUCING TEE
REDUCING TEECROSS
TR
TRX
2”
4”
2” 2”
W3 + 6”
L2”
2”
W2 ≥ W3
L = W1 – W2
6” Minimum
W3 ≥ W4
W2 + 6”
[W1+
2”]x
[D1+
2”]
W1 x D1
[W2+2”]x[D2+2”]
W2 x D2
[W1+
2”]x
[D1+
2”]
W1 x D1
[W3+2”]x[D3+2”]
W3 x D3
[W1+
2”]x
[D1+
2”]
W1 x D1
W3 x D3
[W3+2”]x[D3+2”]
[W2+2”]x[D2+2”]
W2 x D2
[W2+2”]x[D
2+2”]
W2 x D2
[W2+2”]x[D
2+2”]
W2 x D2
[W1+
2”]x
[D1+
2”]
W1 x D1
W4 x D4
[W4+2”]x[D4+2”]
[W3+2”]x[D3+2”]
W3 x D3
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
22
Double Wall Oval CONICAL TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 fax
CONICAL TEE
CONICAL CROSS
W2 + 8” 2”2”
CT
CTX
REDUCING CONICAL TEE
REDUCING CONICALCROSS
2” 2”
2”
5” 1” 1”
CTR
CTRX
L = W1 – W2
6” Minimum
W3 + 8” L2”
2”
2” 2”
2”
5” 1” 1”
2” 2”
W2+ 8”
1”
2”1” 1”
2”
1”
W2 ≥ W3
[W1+
2”]x
[D1+
2”]
W1 x D1
[W2+2”]x[D
2+2”]
W2 x D2
[W2+2”]x[D2+2”]
W2 x D2
[W1+
2”]x
[D1+
2”]
W1 x D1
[W3+2”]x[D3+2”]
W3 x D3
[W1+
2”]x
[D1+
2”]
W1 x D1
[W3+2”]x[D3+2”]
W3 x D3
[W2+2”]x[D2+2”]
W2 x D2L = W1 – W2
6” Minimum
2” 2”
W3 + 8”
L
2”
1” 1”
2”
1”
W3 ≥ W4
1”
[W1+
2”]x
[D1+
2”]
W1 x D1
[W4+2”]x[D4+2”]
W4 x D4
[W3+2”]x[D3+2”]
W3 x D3
[W2+2”]x[D
2+2”]
W2 x D2
5” 5”
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
2” 2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
23
Double Wall Oval SHOE TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
SHOE TEE
SHOE TEE CROSS
ST
STX
STR
REDUCING SHOE TEE
REDUCING SHOETEE CROSS
STRX
W2 ≥ W3
2” 2” 2” L
2”
W3 + X + 6”
X
2”
L = W1 - W2
Minimum 6”
W3 ≥ W4
2” 2” 2” 2”
2”
W2 + X + 6”
X
2” 2” 2”
2”
X
2”
W3 + X + 6”
2”
L
2” 2” 2”2”
2”
X
X
2”
W2 + X + 6”
[W2+2”]x[D2+2”]
W2 x D2
[W1+
2”]x
[D1+
2”]
W1 x D1
[W3+2”]x[D3+2”]
W3 x D3
[W1+
2”]x
[D1+
2”]
W1 x D1
[W3+2”]x[D3+2”]
W3 x D3
[W2+2”]x[D2+2”]
W2 x D2
[W1+
2”]x
[D1+
2”]
W1 x D1
[W4+2”]x[D4+2”]
W4 x D4
[W3+2”]x[D3+2”]
W3 x D3
[W1+
2”]x
[D1+
2”]
W1 x D1
[W2+2”]x[D
2+2”]
W2 x D2
W2 x D
2
[W2+2”]x[D
2+2”]
L = W1 - W2
Minimum 6”
W2
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
W3
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
W2, W3
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
W3, W4
3 thru 89 thru 16
17 thru 2627” and up
X5”7”10”13”
X
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
24
[W3+2”]x[D3+2”]
W3 x D3
2”
[W3+2”]x[D3+2”]
W3 x D3
Double Wall Oval STRAIGHT LATERALST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
45º LATERAL
45º LATERAL CROSS
L = W1 – W2
6” Minimum
2” 2”
L2”
2”
L
LX
LR
LRX
45º REDUCING LATERAL
45º REDUCING LATERAL CROSS
(W3 + 2”) x 1.414) + 4”
2” 2”
L = W1 – W2
6” Minimum
W3 ≥ W4W2 ≥ W3
2” 2”
2”2”
2”
(W2 + 2”) x 1.414) + 4”
(W2 + 2”) x 1.414) + 4”
[W1+
2”]x
[D1+
2”]
W1
x D1
[W1+
2”]x
[D1+
2”]
W1
x D1
[W2+2”]x[D2+2”]
W2 x D2
[W1+
2”]x
[D1+
2”]
W1
x D1
[W3+2”]x[D3+2”]
W3 x D3
[W2+2”]x[D2+2”]
W2 x D2
2” 2”
2”
L
(W3 + 2”) x 1.414) + 4”
[W1+
2”]x
[D1+
2”]
W1
x D1
W2 x D
2
[W2+2”]x[D
2+2”]W
2 x D2
[W2+2”]x[D
2+2”]
4”
2”
4”
4”
2”
2”
4”
4”
[W4+2”]x[D4+2”]
W4 x D4
2”
4”2”2”
2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
25
Double Wall Oval CONICAL LATERALST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
45º CONICAL LATERAL
45º CONICALLATERAL CROSS
L = W1 – W2
6” Minimum
CL
CLX
CLR
45º REDUCING CONICAL LATERAL
45º REDUCING CONICALLATERAL CROSS
CLRX
L = W1 – W2
6” Minimum
W3 ≥ W4W2 ≥ W3
2”2”
2”2”
((W2 + 4”) X 1.414) + 4”
L2”
2”
2”2”
((W3 + 4”) X 1.414) + 4”
2”
4”
6”
2”
2”2”
2”
2”
((W2 + 4”) X 1.414) + 4”
4”
L2”
2”4”
2”2”
((W3 + 4”) X 1.414) + 4”
[W1+
2”]x
[D1+
2”]
W1
x D1
[W2+2”]x[D2+2”]
W2 x D2
[W3+2”]x[D3+2”]
W3 x D3
[W1+
2”]x
[D1+
2”]
W1
x D1
[W1+
2”]x
[D1+
2”]
W1
x D1
[W2+2”]x[D2+2”]
W2 x D2
[W3+
2”]x[
D3+2”
]
W3 x D3
[W1+
2”]x
[D1+
2”]
W1
x D1
W2 x D
2
[W2+2”]x[D
2+2”]
W2 x D
2
[W2+2”]x[D
2+2”]
4”
6”
2”
6”
2”
6”
4”
6”
2”
[W3+2”]x[D3+2”]
W3 x D3
2”
4”
6”
[W4+
2”]x[
D4+2”
]
W4 x D4
2”
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
26
Double Wall Oval MISCELLANEOUST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
ECCENTRIC REDUCER
PC
FITTING COUPLING
FC
CONCENTRIC REDUCER
E45 RDERDC
L = 2 [W1 – W2]6” Minimum
L = W1 – W2
6” Minimum
2” 2”L 2” 2”X
PIPE COUPLING
2” 2” 2” 2”
END CAP2”
[W1+
2”]x
[D1+
2”]
W1
x D1W
2 x D2
[W2+2”]x[D
2+2”]
W1 x D1 W1 x D1
W1 x D1
[W1+
2”]x
[D1+
2”]
W1
x D1 W
2 x D2
[W2+2”]x[D
2+2”]
ECRTR
O1
TD
W1 x D1
L
[W1 +2”]x[D1+2”]
W2 x D2
[W2+2”]x[D2+2”]
RECTANGULAR TOROUND
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
27
W2 x D2
REDUCING BULL HEAD TEE With or without vanes.
Double Wall Oval MISCELLANEOUST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
ROUND TO ROUND
E22/E45 E60
Y45
REDUCINGY BRANCH
YR45
OFFSET
E45 ROET
BULL HEAD TEE With or without vanes.BHT/BHTV
SET
BHTR/BHTRV
Y BRANCH
01
L
2”
D1 No. ofvanes
3-7
8-10
10-60
>60
1
3
5
Max 12”spacing
2”2”
2” 2”
2”2”
W1 + 6”2” 2”
2”2”2” 2”
2”
W1 + 6”
2"
2"2"
2"
2"2" 2"
[W1+
2”]x
[D1+
2”]
W1
x D1
2” 2”
2”2”
2” 2”
W1 x D1
[W1+2”]x[D1+2”]W1 x D1
[W1+2”]x[D1+2”]
[W2+
2”]x[
D2+2”
]
W3 x D3
[W3+2”]x[D3+2”]
W1 x D1
[W1+2”]x[D1+2”]
W1 x D1
[W1+2”]x[D1+2”]
[W2+
2”]x
[D2+
2”]
W2
x D2
[W3+2”]x[D
3+2”]
W3 x D
3
L2 = W1 – W3
6” MinimumL1 = W1 – W2
6” Minimum
L1 L2
W2 x D2
L
TD
O1
[W2 + 2] X[D2 +2]
W1 x D1
[W1 + 2] X[D1 +2]
L2 = W1 – W3
6” MinimumL1 = W1 – W2
6” Minimum
L1 L2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
28
Shop/Field Installed ACCESSORIEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
RECTAP
CONICAL TAP
E22/E45
TAP
E45 CTAP 90
REGISTER TAP
TAP 90
ADOOR
Standard flange is 1/2”.2” saddle is also available.
ACCESS DOOR
Standard flange is 1/2”.2” saddle is also available.
1/2” Flange
Flange in or out 4”
D1
[D2+2”]x[W2+2”]
W1
TAP 45 STR
LATERAL TAP
Standard flangeis 1/2”. 2” saddleis also available.
Standard flangeis 1/2”. 2” saddleis also available.
SHOE TAP
2”
W2xD2
4”
[W2+2”]x[D2+2”]
W1 x D1
[W1+2”]x[D1+2”]
2”
L
W1 x D1
[W1+2”]x[D1+2”]
W2xD2
[W2+2”]x[D2+2”]
D1
W1
4”
2” 4”
D1
W1
W2
3 thru 89 thru 16
17 thru 2627” and up
L5”7”10”13”
D1
W1
[D2+
2”]x
[W2+
2”]
1”
1”2” 5”
[D2+
2”]x
[W2+
2”]
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
29
1
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
Rectangular Duct SEAMS & CONNECTORSTA M B E M E T A L P R O D U C T S
L-1 Pittsburgh lock L-2 Button punchsnap lock
Corner weldL-5 Singlecorner seam
L-4 Standing seam
Flanged(With gasket)
T-25b
H
T- 22 Companion angles
HRivet or
weld
T- 21 Weld flange
T-10 Standing S
H
T- 1 Drive slip T- 6 Hemmed “S” slip
Lap seam
Connector Types
Seam Types
2
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
Rectangular Duct STANDARDSTA M B E M E T A L P R O D U C T S
TDF Connection Recommended clip spacing
60” duct4 clips required
48” duct3 clips required
36” duct3 clips required
24” duct2 clips required
18” duct and smaller1 clip required
Method of fabrication:Two “L” shaped sections are assembled in the field to form the finished joint of ductwork. This allows ductwork to be shipped in knocked down condition requiring less cartage space and easier han-dling. Wrap around fabrication also available.
56” finished length with T.D.F.
59” finished length with drive cleat edges
60” length with ends unfinished
Straight Duct
3
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
12”13”14”15”16”17”18”19”20”21”22”23”24”25”26”27”28”29”30”31”32”33”34”35”36”37”38”39”40”41”42”43”44”45”46”47”48”49”50”51”52”53”54”55”56”57”58”59”60”61”62”63”64”65”66”
2.072.242.402.582.762.923.103.273.433.613.783.954.124.284.454.644.814.975.155.315.485.675.846.006.186.346.526.706.877.037.217.377.557.737.908.078.248.418.588.758.939.109.379.449.619.789.9610.1310.3010.4710.6410.8110.9911.1611.33
2.142.302.452.602.762.913.073.233.383.593.703.8640.14.164.314.474.644.794.945.115.255.415.575.725.886.046.196.346.506.656.816.967.127.277.437.597.757.908.058.278.378.528.688.838.989.149.309.459.619.769.9210.0810.2410.3910.55
2.732.933.123.323.533.723.924.124.314.524.724.925.115.315.515.725.926.126.316.516.716.907.107.307.507.697.898.118.308.508.698.889.089.289.489.689.8810.0810.2810.4810.6810.8711.0711.2611.4611.6611.8712.0712.2712.4612.6512.8513.0613.2513.45
3.123.353.603.844.084.324.574.805.255.505.745.986.236.476.706.957.197.447.677.918.158.398.648.889.139.369.609.8510.0910.3310.5610.8011.0511.2911.5411.7812.0212.2512.4912.7312.9813.2213.4713.7013.9414.1914.4414.6714.9115.1515.4015.64153.8816.1216.36
3.673.954.244.524.805.095.375.666.196.486.767.057.337.617.908.198.478.769.049.329.609.8910.1810.4610.7411.0211.3111.6011.8812.1612.4512.7313.0213.3113.6013.8714.1514.4314.7215.0015.2915.5715.8616.1416.4216.7117.0017.2817.5717.8418.1218.4118.7118.9919.27
4.775.145.525.896.256.636.997.368.068.438.819.189.549.9110.2810.6611.0411.4011.7712.1312.5012.8813.2613.6213.9814.3514.7215.1015.4815.8416.2116.5716.9417.3217.7018.0618.4218.7919.1719.5419.9220.2820.6521.0121.3821.7622.1422.5022.8723.2423.6123.9824.3624.7225.09
67”68”69”70”71”72”73”74”75”76”77”78”79”80”81”82”83”84”85”86”87”88”89”90”91”92”93”94”95”96”97”98”99”100”101”102”103”104”105”106”107”108”109”110”111”112”113”114”115”116”117”118”119”120”
11.4911.6611.8412.0212.1912.3612.5312.7012.8713.0513.2213.3913.5613.7313.9014.0814.2514.4214.5914.7614.9315.1115.2815.4515.6215.7915.9616.1416.3116.4816.6516.8216.9917.1717.3417.5117.6817.8518.0218.2018.3718.5418.7118.8819.0519.2319.4019.5719.7419.9120.0820.2620.4420.66
10.7010.8511.0011.1611.3111.4711.6211.7811.9412.1012.2512.4112.5612.7212.8813.0413.1913.3513.5013.6513.8113.9714.1214.2814.4314.5814.7414.9015.0515.2115.3615.5215.6715.8315.9816.1416.2916.4516.6116.7716.9217.0717.2317.3917.5517.7117.8618.0118.1618.3118.4718.6318.7918.95
13.6413.8414.0414.2514.4414.6414.8415.0415.2415.4415.6315.8316.0316.2316.4216.6216.8217.0317.2217.4217.6217.8318.0218.2218.4118.6118.8119.0119.2119.4119.6019.8020.0020.2120.4020.6020.7920.9921.1921.3921.5821.7821.9822.1822.3822.5922.7822.9823.1723.3723.5723.7823.9824.18
16.6016.8417.0817.3317.5617.8018.0418.2918.5418.7919.0219.2619.4919.7319.9820.2320.4720.7120.9521.1921.4321.6821.9222.1622.4022.6422.8823.1223.3623.6123.8424.0824.3324.5824.8125.0525.2925.5325.7826.0326.2626.5026.7426.9827.2227.4727.7127.9528.1928.4328.6728.9229.1629.40
19.5519.8320.1220.4120.6920.9821.2621.5521.8322.1222.4022.6822.9623.2523.5323.8224.1024.3924.6724.9625.2425.5325.8126.1026.3826.6626.9527.2427.5227.8028.0828.3728.6528.9429.2229.5129.7930.0830.3630.6530.9331.2131.4931.7832.0632.3532.6332.9233.2033.4833.7734.0634.3534.63
25.4525.8226.2026.5826.9527.3227.6828.0528.4228.8029.1629.5329.9030.2730.6431.0231.3831.7532.1332.4932.8733.2533.6133.9834.3434.7135.0835.4635.8236.1936.5636.9337.3137.6938.0538.4238.7839.1539.5239.9040.2640.6341.0041.3841.7542.1342.4942.8643.2243.5943.9744.3544.7245.09
DUCT SIZE
TOTALSq. Ft. 26
gauge24
gauge22
gauge20
gauge18
gauge
WEIGHT PER FOOT OF DUCT DUCT SIZE
TOTALSq. Ft. 26
gauge24
gauge22
gauge20
gauge18
gauge
WEIGHT PER FOOT OF DUCT
Weights on STRAIGHT and T.D.F.TA M B E M E T A L P R O D U C T S
Rectangular ELBOWST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
RE/REV
CETL
CER
CET
E
W2
W1 x D1
S2
S1
A1º
A1º
R1
TD1
W1 x D1
S1
S2
W2 x D2
A1º
TD1
R1
W1 x D1
S1
S2
W2 x D2
W2
W1 x D1
S1
S2
W2
W1 x D1
S1
S2
A1º
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
4
Rectangular TRANSITIONST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
OG
OGL
W2 x D2
W1 x D1 S1
S2
L
O1
TD
W2 x D2
W1 x D1S1
S2
L
O1
TD
RDS2U
W2
W1 x D1 S1
S2
L
RSL
W2 x D2
W1 x D1S1
S2
L
O1
TD
RS
W2 x D2
W1 x D1S1
S2
L
O1
TD
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
5
Rectangular Y’S & TEEST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
SCY
TEE/TEEV
SCE
CYT
YS
W1 x D1
W2 x D2 W3 x D3
TD
S2
S1 S1
L
O2 O3
W1 x D1
W2 x D2
R2
S1
R1
W3 x D2
W2 x D2
W1 x D1
S2
LTD1
TD2 TD3
W3 x D3 W4 x D4
S3
S1
R1 R2
W2 x D2
W1 x D1
TD1TD2
W3 x D3
S1
R1
L
W2
W1 x D1S2
S1
W3
S3
TD1 TD2
S3S2
S2
X
S3
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
6
Rectangular MISCELLANEOUST A M B E M E T A L P R O D U C T S
TAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-3031 faxTAMBE Metal Products • 7385 Willowbrook Road • Victor, NY 14564 • 716-924-3030 • 800-724-3845 • 716-924-4989 fax
W2
W1 x D1
S2
S1
REO
RO
ATAP
STAP
O1
W1 x D1
L
Aº
W2
W1 x D1O1
S2
S1
L
W1 x D1
Aº
L
W3
S1
TAMBE Metal Products • 716-924-3030 • 800-724-3845 • 716-924-4989 fax • Sales • 716-473-5786 • 716-473-2150 fax
7