•••

•

http://www.fixez.com/ Page 1 of 9

TTT-9004 T5 Torx ScrewdriverTTT-9010 Plastic Opening ToolsTTT-9013 SpudgerHeat Gun / Blow Dryer

Motorola Atrix HD MB886 - Disassemble Guide

5HTXLUHG�7RROV�

The repair of the Motorola Atrix HD MB886, can be both simple and inexpensive if you follow the steps of this disassemble guide. To assist you in completing the repair, the steps we have provided will help you quickly, and safely, replace a broken display, along with other internal components that may have become damaged.

You can find a full archive of fixez.com disassemble guides and videos, for numerous makes and models of phones and tablets, by visiting http://www.fixez.com.

• On the bottom left hand side of the Motorola Atrix HD is the door for the SIM card and MicroSD. Open the door and remove the cards before proceeding with your disassemble.

• To take the back cover off the phone, use theplastic opening tool to pry it off. Un-snap each clipcarefully as you work around the perimeter of thephone.

Step 3

•

Step 1 – LCD & Touch Screen

Step 2

http://www.fixez.com/ Page 2 of 9

Motorola Atrix HD–Disassemble Guide

• Remove the back cover from the Motorola AtrixHD.

There is a small amount of adhesive on the center of the back to attach it to the battery. Using the spudger, separate the adhesive to free the back cover from the phone.

Step 4

• There are ten T5 torx head screws that secure the rear chassis onto the phone. Use the T5 torx bit screwdriver to remove these screws and free the chassis.

•

•

Step 5

Step 6 – Speaker Assembly

http://www.fixez.com/ Page 3 of 9

Motorola Atrix HD–Disassemble Guide

Once all of the screws are removed from the chassis, utilize the plastic opening tool to separate the rear chassis from the body of the Motorola Atrix HD.

With the rear portion of the chassis removed, use the pointed end of the spudger to gently pry the speaker assembly up out of its location. It is held down with a small amount of adhesive.

• You can now remove the speaker assembly fromthe Motorola Atrix HD.

• To remove the battery, go back to the main body ofthe phone. Using the appropriate screwdriver,remove the two T5 torx screws that secure thebattery’s terminals down to the case.

• The battery is also secured down by a small amountof adhesive. Using the spudger and battery pull-tab,pick the battery up out of its location in the phone.

Step 9

• The frame that housed the battery is secured to the body of the phone by ten T5 torx screws. Using the T5 torx bit screwdriver, remove these screws.

Step 7 - Battery

Step 8

http://www.fixez.com/ Page 4 of 9

Motorola Atrix HD–Disassemble Guide

• Remove the battery from the Motorola Atrix HD.

• With the ten screws removed, you can now removethe frame from the Motorola Atrix HD.

• The touch screen connector is the first connection tobe removed. Put the flat end of the spudger underthe connection. Turn the spudger so it pulls the plugup and out of its socket.

Step 12

Step 10 – LCD

Step 11

http://www.fixez.com/ Page 5 of 9

• Follow the previous steps to remove the LCDconnection. The connection is next to the touchscreen connector that was just removed.

• The motherboard is next. Removing themotherboard from the phone will require thespudger in order to pry it up from the displayassembly. Make sure the LCD is not stuck to thebottom of the motherboard with adhesive.

Motorola Atrix HD–Disassemble Guide

• There are three layers to the phone: the touchscreen, the LCD, and the motherboard.

Step 15 – Touch Screen

Step 13

Step 14

http://www.fixez.com/ Page 6 of 9

• Use the spudger, and a little force, to pry up the LCD from the touch screen. The LCD and touch screen should now be separated.

• To separate the touch screen digitizer from the front frame of the phone, use patience and the spudger to pry it up. With these, the separation will come easily. The adhesive that secures the touch screen to the frame is minimal.

Motorola Atrix HD–Disassemble Guide

• If the LCD is stuck to the motherboard like ours, usethe spudger to separate the LCD from the bottom ofthe motherboard.

• Remove the motherboard from the Motorola AtrixHD.

• Remove the LCD from the Motorola Atrix HD.

• Remove the touch screen digitizer from theMotorola Atrix HD.

• Now turn your attention to the motherboard. Use thespudger to pry up the front-facing cameraconnection.

Step 18

Step 16 – Front-Facing Camera

Step 17

http://www.fixez.com/ Page 7 of 9

• With the connection out of its socket, remove the oneT5 torx screw that secures the camera assembly tothe motherboard.

• Use the spudger to maneuver the front facingcamera from the Motorola Atrix.

Motorola Atrix HD–Disassemble Guide

• The rear-facing camera can now be removed usingthe spudger. With the spudger, pry the connectionfrom the motherboard. The connection should nowbe released from the Motorola Atrix HD.

Step 21

Step 19 – Rear-Facing Camera

Step 20 – Earpiece Speaker

http://www.fixez.com/ Page 8 of 9

• Remove the rubber grommet. It is hiding one of the three screws that secures the earpiece speaker to the phone.

• Locate and remove all three of the T5 torx screws with the appropriate screwdriver.

Motorola Atrix HD–Disassemble Guide

• Remove the earpiece speaker from the MotorolaAtrix HD.

http://www.fixez.com/ Page 9 of 9

Motorola Atrix HD–Disassemble Guide

Final Layout

Notice/Warning:FIXEZ.COM DOES NOT ACCEPT ANY LIABILITY FOR DAMAGE, OR INJURY CAUSED, WHILE YOU ARE FOLLOWING OUR DISASSEMBLE GUIDES. WE MAKE NO REPRESENTATIONS, WARRANTIES, OR CONDITIONS OF ANY KIND, EXPRESS OR IMPLIED. UTILIZING THESE GUIDES TO HELP ASSIST YOU IN REPAIRING YOUR MOBILE DEVICES WILL VOID YOUR WARRANTY. FIXEZ.COM STRICTLY PROHIBITS ALTERING OR MODIFYING OUR DISASSEMBLE GUIDES FOR COMMERCIAL USE, REPRODUCTION, OR PUBLICATION.

To reassemble your device, follow these instructions in reverse order.