04 Mustang Manual

7/28/2019 04 Mustang Manual

1/240

Introduction 4

Instrument Cluster 10

Warning and control lights 10

Gauges 14

Entertainment Systems 18

AM/FM stereo with CD 18AM/FM stereo with in-dash six CD 25

Climate Controls 33

Manual heating and air conditioning 33

Rear window defroster 34

Lights 35

Headlamps 35Turn signal control 38

Bulb replacement 38

Driver Controls 43

Windshield wiper/washer control 43Steering wheel adjustment 44

Power windows 45

Mirrors 46Speed control 46

Locks and Security 54

Keys 54

Locks 54Anti-theft system 57

2004 Mustang(mus)Owners Guide (post-2002-fmt)USA English (fus)

Table of Contents

1


2/240

Seating and Safety Restraints 64Seating 64Safety restraints 68

Air bags 79Child restraints 84

Driving 99

Starting 99

Brakes 104Traction control 107

Transmission operation 108Vehicle loading 117

Trailer towing 120

Roadside Emergencies 122Getting roadside assistance 122Hazard flasher switch 124

Fuel pump shut-off switch 124

Fuses and relays 125Changing tires 130

Jump starting 136Wrecker towing 141

Customer Assistance 142

Reporting safety defects (U.S. only) 152

Cleaning 153

Maintenance and Specifications 161

Engine compartment 164Engine oil 167

Battery 171Fuel information 182

Part numbers 215Refill capacities 215

Lubricant specifications 218


Table of Contents

2


3/240

Accessories 225

Index 228

All rights reserved. Reproduction by any means, electronicor mechanical including photocopying, recording or by anyinformation storage and retrieval system or translation inwhole or part is not permitted without writtenauthorization from Ford Motor Company. Ford may changethe contents without notice and without incurringobligation.

Copyright 2003 Ford Motor Company


Table of Contents

3


4/240

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of itsconstituents, and certain vehicle

components contain or emit chemicals known tothe State of California to cause cancer and birthdefects or other reproductive harm. In addition,certain fluids contained in vehicles and certainproducts of component wear contain or emitchemicals known to the State of California tocause cancer and birth defects or otherreproductive harm.

CONGRATULATIONS

Congratulations on acquiring your new Ford. Pleasetake the time to get well acquainted with your

vehicle by reading this handbook. The more you

know and understand about your vehicle the greater

the safety and pleasure you will derive from driving

it.

For more information on Ford Motor Company and

its products visit the following website:

In the United States: www.ford.com

In Canada: www.ford.ca

In Australia: www.ford.com.au

In Mexico: www.ford.com.mx

Additional owner information is given in separate

publications.

This Owners Guide describes every option and

model variant available and therefore some of the

items covered may not apply to your particular

vehicle. Furthermore, due to printing cycles it may

describe options before they are generally available.

Remember to pass on the Owners Guide when

reselling the vehicle. It is an integral part of thevehicle.


Introduction

4


5/240

Fuel pump shut-off switch In the event ofan accident the safety switch will

automatically cut off the fuel supply to the engine.The switch can also be activated through suddenvibration (e.g. collision when parking). To resetthe switch, refer to the Fuel pump shut-offswitch in the Roadside emergencies chapter.

SAFETY AND ENVIRONMENT PROTECTION

Warning symbols in this guide

How can you reduce the risk of personal injury andprevent possible damage to others, your vehicle andits equipment? In this guide, answers to such

questions are contained in comments highlighted bythe warning triangle symbol. These commentsshould be read and observed.

Warning symbols on your vehicle

When you see thissymbol, it is imperativethat you consult therelevant section of thisguide before touching or attempting adjustment ofany kind.

Protecting the environment

We must all play our

part in protecting theenvironment. Correctvehicle usage and theauthorized disposal of waste cleaning and lubricationmaterials are significant steps towards this aim.Information in this respect is highlighted in thisguide with the tree symbol.

BREAKING-IN YOUR VEHICLE

Your vehicle does not need an extensive break-in.Try not to drive continuously at the same speed forthe first 1,600 km (1,000 miles) of new vehicle


Introduction

5


6/240

operation. Vary your speed to allow parts to adjustthemselves to other parts.

Do not add friction modifier compounds or specialbreak-in oils during the first few thousandkilometers (miles) of operation, since these additivesmay prevent piston ring seating. See Engine oil inthe Maintenance and specifications chapter formore information on oil usage.

SPECIAL NOTICES

Emission warranty

The New Vehicle Limited Warranty includesBumper-to-Bumper Coverage, Safety RestraintCoverage, Corrosion Coverage, and 6.0L PowerStroke Diesel Engine Coverage. In addition, yourvehicle is eligible for Emissions Defect andEmissions Performance Warranties. For a detaileddescription of what is covered and what is notcovered, refer to the Warranty Guide that isprovided to you along with your Owners Guide.

Special instructions

For your added safety, your vehicle is fitted withsophisticated electronic controls.

Please read the section SupplementalRestraint System (SRS) in the Seating and

safety restraints chapter. Failure to follow thespecific warnings and instructions could result inpersonal injury.

Front seat mounted rear facing child orinfant seats should NEVER be used in front

of a passenger side air bag unless the air bag canbe and is turned OFF.

Data Recording

Computers in your vehicle are capable of recordingdetailed data potentially including but not limited toinformation such as:


Introduction

6


7/240

the use of restraint systems including seat beltsby the driver and passengers,

information about the performance of varioussystems and modules in the vehicle, and

information related to engine, throttle, steering,brake or other system status.

Any of this information could potentially includeinformation regarding how the driver operates thevehicle, potentially including but not limited toinformation regarding vehicle speed, brake oraccelerator application, or steering input. Thisinformation may be stored during regular operationor in a crash or near crash event.

This stored information may be read out and usedby:

Ford Motor Company.

service and repair facilities.

law enforcement or government agencies.

others who may assert a right or obtain yourconsent to know such information.

Notice to owners of Cobra vehicles

Before you drive your vehicle, be sure to read theSVT Cobra Owners Guide Supplement. This bookcontains important operation and maintenanceinformation.

MIDDLE EAST/NORTH AFRICA VEHICLE

SPECIFIC INFORMATIONFor your particular global region, your vehicle maybe equipped with features and options that aredifferent from the ones that are described in thisOwner Guide; therefore, a supplement has beensupplied that complements this book. By referring tothe pages in the provided supplement, you canproperly identify those features, recommendationsand specifications that are unique to your vehicle.Refer to this Owner Guide for all otherrequired information and warnings.


Introduction

7


8/240

These are some of the symbols you may see on yourvehicle.

Vehicle Symbol Glossary

Safety Alert See Owners Guide

Fasten Safety Belt Air Bag-Front

Air Bag-Side Child Seat

Child Seat

Installation Warning

Child Seat Lower

Anchor

Child Seat Tether

AnchorBrake System

Anti-Lock Brake

System

Brake Fluid -

Non-Petroleum

Based

Traction Control AdvanceTrac

Master Lighting

Switch

Hazard Warning

Flasher

Fog Lamps-Front Fuse Compartment

Fuel Pump ResetWindshield

Wash/Wipe

Windshield

Defrost/Demist

Rear Window

Defrost/Demist

Power Windows

Front/Rear

Power Window

Lockout


Introduction

8


9/240

Vehicle Symbol Glossary

Child Safety Door

Lock/Unlock

Interior Luggage

Compartment

Release Symbol

Panic Alarm Engine Oil

Engine CoolantEngine Coolant

Temperature

Do Not Open When

HotBattery

Avoid Smoking,Flames, or Sparks

Battery Acid

Explosive Gas Fan Warning

Power Steering

Fluid

Maintain Correct

Fluid Level

MAX

MIN

Emission System Engine Air Filter

Passenger

Compartment Air

Filter

Jack

Check fuel cap Low tire warning


Introduction

9


10/240

WARNING LIGHTS AND CHIMESBase instrument cluster

Optional instrument cluster

Mach 1 instrument cluster

Warning lights and gauges can alert you to a vehiclecondition that may become serious enough to causeexpensive repairs. A warning light may illuminatewhen a problem exists with one of your vehiclesfunctions. Many lights will illuminate when you startyour vehicle to make sure the bulb works. If anylight remains on after starting the vehicle, have therespective system inspected immediately.

P!

BRAKE

L

0

0 0 0 0 0 00

C

E F

H L H

10

20

30

20

40

60

80100 120

140

160

180

40

5060 70

80

90

100

110

120

4

5

6

7

3

2

1

H

THEFT

RPMX1000

FUEL DOOR

SELECT/RESET

LOWFUEL

O/DOFF

AIRBAG

SERVICEENGINESOON

MPH k m/h

ABS

.

CHECKFUELCAP

P!

BRAKE

L

0

0 0 0 0 0 00

C

E F

H L H

10

20

40

60

80

20

40

60

80100

120140160

180

200

220

240

100

120

140

30

50

70 90

110

130

150

45

6

7

8

3

2

1

H

THEFT

RPMX1000

FUEL DOOR

SELECT/RESET

LOWFUEL

O/DOFF

AIRBAG

SERVICEENGINESOON

CHECKFUELCAP

MP H k m/ h

ABS

.


Instrument Cluster

10


11/240

Service engine soon:The Service enginesoon indicator lightilluminates when theignition is first turned to the ON position to checkthe bulb. Solid illumination after the engine isstarted indicates the On Board Diagnostics System(OBD-II) has detected a malfunction. Refer to Onboard diagnostics (OBD-II) in the Maintenanceand Specifications chapter. If the light is blinking,engine misfire is occurring which could damage yourcatalytic converter. Drive in a moderate fashion(avoid heavy acceleration and deceleration) andhave your vehicle serviced immediately.

Under engine misfire conditions, excessive

exhaust temperatures could damage thecatalytic converter, the fuel system, interior floorcoverings or other vehicle components, possiblycausing a fire.

Check fuel cap:Illuminates when thefuel cap may not beproperly installed.Continued driving with this light on may cause theService engine soon light to come on. Refer to Fuel

filler cap in the Maintenance and Specificationschapter.

Brake systemwarning light: Toconfirm the brakesystem warning light isfunctional, it will momentarily illuminate when theignition is turned to the ON position when theengine is not running, or in a position between ONand START, or by applying the parking brake whenthe ignition is turned to the ON position. If thebrake system warning light does not illuminate atthis time, seek service immediately from yourdealership. Illumination after releasing the parking

SERVICEENGINESOON

CHECKFUELCAP

P!

BRAKE


Instrument Cluster

11


12/240

brake indicates low brake fluid level and the brakesystem should be inspected immediately by yourservicing dealership.

Driving a vehicle with the brake systemwarning light on is dangerous. A significant

decrease in braking performance may occur. It willtake you longer to stop the vehicle. Have thevehicle checked by your dealer immediately.

Anti-lock brakesystem: If the ABSlight stays illuminatedor continues to flash, amalfunction has been detected, have the systemserviced immediately. Normal braking is stillfunctional unless the brake warning light also isilluminated.

Air bag readiness: Ifthis light fails toilluminate whenignition is turned to ON, continues to flash orremains on, have the system serviced immediately. Achime will also sound when a malfunction in thesupplemental restraint system has been detected.

Safety belt: Remindsyou to fasten your

safety belt. A chimewill also sound toremind you to fasten your safety belt.

Charging system:Illuminates when thebattery is not chargingproperly.

Low fuel: Illuminateswhen the fuel level inthe fuel tank is at ornear empty. Refer toFuel gauge in this chapter).

ABS

AIR

BAG

LOW

FUEL


Instrument Cluster

12


13/240

Overdrive off:Illuminates when theoverdrive function ofthe transmission has been turned off, refer to theDriving chapter. If the light flashes steadily or doesnot illuminate, have the transmission serviced soon,or damage may occur.

Traction Controlactive: Illuminateswhen the TractionControl system isactive. If the lightremains on, have the system serviced immediately.

Anti-theft system:

Flashes when theSecurilock PassiveAnti-theft System has been activated.

Turn signal:Illuminates when theleft or right turn signalor the hazard lights are turned on. If the indicatorsstay on or flash faster, check for a burned out bulb.

High beams:Illuminates when thehigh beam headlampsare turned on.

Key-in-ignition warning chime: Sounds when thekey is left in the ignition in the OFF/LOCK or ACCposition and the drivers door is opened.

Headlamps on warning chime: Sounds when theheadlamps or parking lamps are on, the ignition isoff (the key is not in the ignition) and the driver sdoor is opened.

O/DOFF


Instrument Cluster

13


14/240

GAUGESBase instrument cluster gauges

Optional instrument cluster gauges

Mach 1 instrument cluster gauges

Speedometer: Indicates the current vehicle speed.

Base instrumentcluster

P!

BRAKE

L

C

E F

H L H

10

20

30

20

40

60

80100 120

140

160

180

40

5060 70

80

90

100

110

120

4

5

6

7

3

2

1

H

THEFT

RPMX1000

FUEL DOOR

SELECT/RESET

LOWFUEL

O/DOFF

AIRBAG

SERVICEENGINESOON

MPH km /h

ABS

0 0 0 0 0 00.

CHECKFUELCAP

P!

BRAKE

0

0 0 0 0 0 00F

H H

10

20

40

60

80

20

40

60

80

100120140

160

180

200

220

240

100

120

140

30

50

70 90

110

130

150

45

6

7

8

3

2

1

H

THEFT

RPMX1000

FUEL DOOR

SELECT/RESET

LOWFUEL

O/DOFF

AIRBAG

SERVICEENGINESOON

MPH k m/h

ABS

.

L

L

CHECKFUELCAP


Instrument Cluster

14


15/240

Optional instrumentcluster

Mach 1 instrumentcluster

Engine coolanttemperature gauge:

Indicates enginecoolant temperature. At

normal operating temperature, the needle will be in

the normal range (between H and C). If it enters

the red section, the engine is overheating. Stop the

vehicle as soon as safely possible, switch off theengine and let the engine cool.

Never remove the coolant reservoir capwhile the engine is running or hot.

Odometer: Registersthe total kilometers

(miles) of the vehicle.

Trip odometer:Registers thekilometers (miles) ofindividual journeys.Press and release thereset button until a Tappears in the display.Press and hold the button for three seconds to reset.

C H

0

0 0 0 0 0 00

45

6

7

8

3

2

1

RPMX1000

SELECT/RESET

.


Instrument Cluster

15


16/240

Tachometer: Indicates the engine speed inrevolutions per minute. Driving with yourtachometer pointer continuously at the top of thescale may damage the engine.

Base instrumentcluster

Optional instrumentcluster

Mach 1 instrumentcluster

Battery voltagegauge: Indicates thebattery voltage whenthe ignition is in theON position. If the pointer moves and stays outsidethe normal operating range, have the vehicles

electrical system checked as soon as possible.Engine oil pressuregauge: Indicatesengine oil pressure.The needle should stayin the normal operating range (between L andH). If the needle falls below the normal range, stopthe vehicle, turn off the engine and check the engineoil level. Add oil if needed. If the oil level is correct,have your vehicle checked at your dealership or by aqualified technician.

L H

L H


Instrument Cluster

16


17/240

Fuel gauge: Indicatesapproximately howmuch fuel is left in thefuel tank (when theignition is in the ON position). The fuel gauge mayvary slightly when the vehicle is in motion or on agrade.

Refer to Filling the tank in the Maintenance andSpecifications chapter for more information.

F


Instrument Cluster

17


18/240

AM/FM STEREO / SINGLE CD RADIO (IFEQUIPPED)

1. Balance:

Press / to shift

sound to the left/rightspeakers.

2. Fade: Press /

to shift sound to thefront/rear speakers.

3. SCN (Scan): Pressto hear a brief samplingof all listenable stations

or CD tracks. Press again to stop.4. CLK: To set thehour, press and holdCLK and press SEEK

to decrease or increase the hours.

To set the minute, press and hold CLK and press

TUNE to decrease or increase the minutes.

5. EJ (eject): Press toeject a CD.

BASS

CD

TREB BAL FADE

SCN

CLK

AMFM

VOL - PUSH ON

SEEK EJ

COMP

DISC

DISCSTUNE

1 2 3 4 5 6

FM1 ST

SHUFFLECDCD

14 15 16 17 18 1 2 3 413

6 58

12

11

7910

CLK


Entertainment Systems

18


19/240

6. COMP(Compression): In CDmode, press to bringlouder and softer levels into more comfortablelistening level. The compression icon (c) will appearin the display.

7. Shuffle: Press tolisten to the tracks onthe CD in randomorder. Press again to turn off.

8. Memory presets:To set a station: Selectfrequency bandAM/FM; tune to a station. Press and hold a preset

button until sound returns. This radio is equippedwith six station memory preset controls which allowyou to set up to six AM stations and 12 FM stations(six in FM1 and six in FM2).

9. CD: Press and

hold until desiredselection is reached.

10. CD:Press

and hold until desiredselection is reached.

11. Tune / Discs: Inradio mode, press tomove up or down the

frequency band in individual increments.12. Seek: Press and

release SEEK /

for previous/nextstrong station, selection or track.

13. Power/volume:Press to turn ON/OFF;turn to increase ordecrease volume levels.

SHUFFLE

6

1 2 3 4 5 6

SHUFFLECDCD



19


20/240

14. CD: Press to enterCD mode or to play aCD already loaded intothe system.

15. AM/FM: Press tochoose a frequencyband in radio mode.

16. Bass:

Press / to

increase/decrease thebass output.

17. Treble:

Press / to

increase/decrease thetreble output.

18. CD door: Insert aCD printed side up.

MACH MP3 AUDIO SYSTEM (IF EQUIPPED)

1. Balance:

Press / to shift

sound to the left/rightspeakers.

2. Fade: Press /

to shift sound to therear/front speakers.

DISC



20


21/240

3. Scan: Press to heara brief sampling of alllistenable radiostations, CD or MP3 tracks. Press again to stop.

4. CLK: To set theclock press and holdthe CLK control for thefollowing functions:

To set the hour, press SEEK / control to

decrease or increase to the hours.

To set the minutes, press TUNE DIR / to

decrease or increase the minutes.

Release CLK to save the clock settings. Press CLK

again to return the display to radio mode.5. EJ (Eject): Press tostop and eject a disc. Ifa disc is ejected andnot removed, the player will automatically reload thedisc and return to radio mode.

6. COMP(Compression): In CDand MP3 mode, pressto adjust the soft and loud sounds together for amore consistent listening level. The compressionicon (c) will illuminate in the display.

7. Shuffle: Press toengage random play on

the CD or MP3 disc.SHF then ON will briefly appear in the display. PressSEEK to select another random track on the disc.Press shuffle again to disable.

8. Repeat: Press torepeat the currenttrack.

9. CD (Fast

forward): Press andhold until the desiredselection point is reached. This function is notenabled in MP3 mode.



21


22/240

10. CD (Rewind):Press and hold untilthe desired selection

point is reached. This function is not enabled in MP3mode.

11. MP3 directory:Allows you to listen tosongs in MP3 flat filemode and MP3 directory mode.

Insert a MP3 disc to engage in the flat file mode.The MP3 icon will be displayed.

While in the MP3 flat file mode, press the MP3DIR control to enter into the directory mode.Press the TUNE DIR control to changedirectories. The MP3 icon and the DIR icon willbe displayed.

12. Track: Press tolocate a specific MP3track or directory.TRAC will appear in the display. Rotate volumecontrol to advance or reverse through the tracks ordirectories. The MP3 icon will flash in the displaywhile the MACH track function is enabled.

13. Memory presets: To set a station: Selectfrequency band AM/FM; tune to a station, press andhold a preset button until sound returns.

14. CD door: Insert a

CD with the label sideup.

15. Tune/Directory:Press TUNE

DIR / to change

the radio frequency down/up or change the MP3directories.

16. Seek: Press and

release SEEK /

for previous/nextstrong station selection or CD and MP3 tracks.



22


23/240


18. CD: Press CD toplay a CD or MP3 disc.When the MP3 disc is

loaded, CD and LOAD will appear on the display.

The display will briefly show the total number of

tracks on the disc as TXXX (XXX=number of

tracks).

19. AM/FM: Press toselect a frequency band

in radio mode.20. Bass:

Press / to

decrease/increase thebass output.

21. Treble:

Press / to

decrease/increase thetreble output.

MP3 FUNCTIONS

Your audio system is equipped with MP3 capability

which allows you to listen to songs in MP3 flat file

mode and MP3 directory mode.

To engage MP3 flat file mode, insert an MP3 disc. Ifan MP3 disc is already present in the player, pressthe CD control. The MP3 icon will display while theplayer is in MP3 mode.

While in MP3 flat filemode, press the MP3DIR control to enterinto MP3 directory mode. The MP3 icon and the DIRicon will display while the player is in directorymode.



23


24/240

Your MACH

MP3 player is also equipped with ananti-shock buffer for MP3 discs.

MP3 FILE DIRECTORY STRUCTURE

The MACH MP3 music system recognizes MP3 disc

file and directory (folder) structure as follows:

There are two different modes for MP3 disc

playback: MP3 flat file mode (default) and MP3

directory mode.

MP3 flat file mode ignores any directory structure

present on the MP3 disc. The player sequentially

numbers each MP3 track on the disc (denoted by

the .mp3 file extension) from T001 to T255.

MP3 directory mode represents a directory

structure consisting of one level of directories

(folders). The CD player sequentially numbers all

MP3 tracks on the disc (denoted by .mp3

extension) and all directories containing MP3

files, from 0101 to 9999. The first two digits

denote the directory number and the last two

digits denote the track number within that

directory.

Creating discs with only one level of

subdirectories will help with navigation through

the disc files.

ERROR MESSAGES

You may experience an error message for thefollowing situations:

NO DISC when the CD control is pressed andthere is not a CD present.

DISC ERR when there is a damaged or unreadabledisc. Such as, data discs containing no .mp3 files,or for data discs containing more than 255 files ordirectories.

CD ERR for any other disc malfunction.



24


25/240

MACH

460 SATELLITE READY SOUNDSYSTEM RADIO CD CHANGER COMPATIBLE(IF EQUIPPED)

MACH 1000 SATELLITE READY SOUNDSYSTEM RADIO CD CHANGER COMPATIBLE(IF EQUIPPED)

Your vehicle may be equipped with the MACH1000 audio system. This system is equipped with arack of amplifiers and subwoofers in the trunk of thevehicle. Do not store or rest items on the amplifierrack, as this could cause damage to the amplifiersand void your warranty.

The MACH 1000 audio system is capable ofproducing very high sound pressure levels. For your



25


26/240

listening comfort and protection, it is notrecommended to listen to the MACH 1000 audiosystem at high volume levels for extended periods oftime.

1. Seek: Press and

release SEEK /

for previous/nextstrong station, selection or track.

2. Rewind: In CDmode, press untildesired selection isreached.

Fast forward: In CD mode, press until desiredselection is reached.

TEXT: TEXT is only available when equipped withSatellite radio. Your Audiophile radio comesequipped with Satellite ready capability. The kit toenable Satellite reception is available through yourFord dealer. Detailed Satellite instructions areincluded with the dealer installed kit.

3. DSP (DigitalSignal Processing):Press DSP to accessthe Ambiance menu. Ambiance gives the feeling ofbeing there to your music, creating increasedclarity as well as an open and spacious feel to themusic. Press SEL to engage/disengage. Turn thevolume control to increase/decrease the level of

ambiance.Occupancy: Press DSP again to change theoccupancy mode to optimize sound for:

ALL SEATS Enhances acoustic sound for allseating locations.

DRIVER SEAT Enhances acoustic sound forthe driver. Rear seat and passenger seatperformance may be compromised in favor of thedriver.

REAR SEAT - Enhances acoustic sound for therear seat passengers.



26


27/240

4. MACH (MACH 1000only): Press to engageMACH 1000 mode.MACH 1000 mode enhances acoustic sound for allseating locations and increases the signal to thetrunk mounted speakers and amplifiers for enhancedbass performance. Press again to return topreviously set occupancy mode.

Mute: (MACH 460only): Press to mutethe playing media.

5. Eject: Press EJ andchoose thecorresponding preset

(16) to eject the desired CD. Press and hold toeject all loaded discs.

6. Bass: Press BASS;then press

SEL / to

decrease/increase the bass output.

Treble: Press TREB;then press

SEL / to

decrease/increase the treble output.

7. Select: Use withBass, Treble, Balanceand Fade controls to

adjust levels.8. Balance: Press BAL;then press

SEL / to shift

sound to the left/right speakers.

Fade: Press FADE;then press

SEL / to shift

sound to the front/rear speakers.



27


28/240

9. Menu: Press MENUand SEL to accessclock mode, RDSon/off, Traffic, Program type, Show type andCompression modes.

Traffic: Allows you to hear traffic broadcasts. Withthe feature ON, press SEEK or SCAN to find astation broadcasting a traffic report (if it isbroadcasting RDS data).Traffic information is notavailable in most U.S. markets.

FIND Program type: Allows you to searchRDS-equipped stations for a certain category ofmusic format: Classic, Country, Info, Jazz, Oldies,R&B, Religious, Rock, Soft, Top 40.

Show TYPE: Displays the stations call letters andformat.

Compression: Brings soft and loud CD passagestogether for a more consistent listening level.

Setting the clock: Press MENU until SELECTHOUR or SELECT MINUTE is displayed. Use SEL to

manually increase ( ) or decrease ( ) the

hours/minutes. Press MENU again to disengage clockmode.

10. Memory presets:To set a station: Selectfrequency bandAM/FM; tune to a station, press and hold a preset

button until sound returns. In CD mode, press toaccess the desired disc.

11. SAT (ifequipped): YourAudiophile radio comesequipped with Satellite Ready capability. The kit toenable the Satellite reception is available throughyour Ford dealer. Detailed satellite instructions areincluded with the dealer installed kit.

12. AM/FM: Press toselect AM/FMfrequency band.



28


29/240

Autostore: Allows you to set the strongest localradio stations without losing your original manuallyset preset stations for AM/FM1/FM2 . Press andmomentarily hold AM/FM. AUTOSTORE will flash onthe display. When the six strongest stations arefilled, the station stored in preset 1 will beginplaying. If there are less than six strong stations, thesystem will store the last one in the remainingpresets. Press again to disengage.


Speed sensitive volume: Radio volume changes

automatically and slightly with vehicle speed tocompensate for road and wind noise. Recommendedlevel is 13. Level 0 turns the feature off and level 7is the maximum setting.Press and hold the volume control for five seconds.

Then press SEL to increase ( ) or decrease ( )

the volume setting. The level will appear in thedisplay.

14. Load: Press LOADand the correspondingpreset (16) to load aCD into the desired slot. Press and hold to load upto six discs at once.

15. CD AUX: Press to

access CD or AUXmode.

CD units are designed to play commerciallypressed 12 cm (4.75 in) audio compact discsonly. Due to technical incompatibility, certainrecordable and re-recordable compact discsmay not function correctly when used in FordCD players. Irregular shaped CDs, CDs with ascratch protection film attached, and CDs withhomemade paper (adhesive) labels should notbe inserted into the CD player. The label maypeel and cause the CD to become jammed. It is



29


30/240

recommended that homemade CDs be identifiedwith permanent felt tip marker rather thanadhesive labels. Ballpoint pens may damage

CDs. Please contact your dealer for further

information.

16. Scan: Press tomove up the radiofrequency band. SCAN

automatically finds a station, plays it for five secondsseconds, then moves to the next station. Press againto stop.CD: Press to sample CD selections for eightseconds. Press again to stop.

17. Disc/Tune: Radio:

Press or to

manually tune down or

up the radio frequency band. CD: Press to select

the previous disc or to select the next disc.

CAT: CAT is only available when equipped withSatellite Radio. Your Audiophile radio comesequipped with Satellite ready capability. The kit toenable Satellite reception is available through yourFord dealer. Detailed Satellite instructions areincluded with the dealer installed kit.

18. CD door: Insertdisc label side up.

For informationregarding SIRIUS Satellite Radio, please call toll-free888-539-SIRIUS (888-539-7474) or visit the SIRIUSwebsite at www.siriusradio.com

RADIO FREQUENCIES

AM and FM frequencies are established by theFederal Communications Commission (FCC) and theCanadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are:

AM - 530, 5401600, 1610 kHz

FM- 87.7, 87.9107.7, 107.9 MHz



30


31/240

RADIO RECEPTION FACTORSThere are three factors that can effect radioreception:

Distance/strength: The further you travel from anFM station, the weaker the signal and the weakerthe reception.

Terrain: Hills, mountains, tall buildings, powerlines, electric fences, traffic lights andthunderstorms can interfere with your reception.

Station overload: When you pass a broadcasttower, a stronger signal may overtake a weakerone and play while the weak station frequency isdisplayed.

CD PLAYER CAREAll audios are CD changer compatible. See yourdealer for further details.

Do:

Handle discs by their edges only. Never touch theplaying surface.

Inspect discs before playing. Clean only with anapproved CD cleaner and wipe from the centerout.

Dont:

Expose discs to direct sunlight or heat sources forextended periods of time.

Insert more than one disc into each slot of the CDchanger magazine.

Clean using a circular motion.

CD units are designed to play commerciallypressed 12 cm (4.75 in) audio compact discsonly. Due to technical incompatibility, certainrecordable and re-recordable compact discsmay not function correctly when used in FordCD players. Irregular shaped CDs, CDs with ascratch protection film attached, and CDs withhomemade paper (adhesive) labels should notbe inserted into the CD player. The label may



31


32/240

peel and cause the CD to become jammed. It isrecommended that homemade CDs be identifiedwith permanent felt tip marker rather thanadhesive labels. Ball point pens may damageCDs. Please contact your dealer for furtherinformation.

AUDIO SYSTEM WARRANTY AND SERVICE

Refer to the Warranty Guide for audio systemwarranty information. If service is necessary, seeyour dealer or qualified technician.



32


33/240

MANUAL HEATING AND AIR CONDITIONINGSYSTEM

1. Fan speedadjustment: Controlsthe volume of aircirculated in thevehicle.

2. Temperature selection: Controls thetemperature of the airflow in the vehicle.

3. Air flow selections: Controls the direction ofthe airflow in the vehicle. See the following for abrief description on each control.

MAX A/C: Uses recirculated air through theinstrument panel registers to cool the vehicle. This

mode is more noisy than A/C, but is moreeconomical and efficient. May reduce undesirableodors from entering the vehicle.

A/C: Uses outside air to cool the vehicle. Air flowsfrom the instrument panel register vents only.

: Distributes outside air through the instrumentpanel vents.

O (OFF): Outside air is shut out and the fan willnot operate.

: Distributes outside air through the floor vents.

: Distributes outside air through the windshield

defroster vents and floor vents.

: Distributes outside air through the windshielddefroster vents.

OPERATING TIPS

To reduce fog build up on the windshield duringhumid weather, place the air flow selector in

the position.

To reduce humidity build up inside the vehicle:during cold weather, do not drive with the airflow selector in the OFF or MAX A/C position.during warm weather, do not drive with the airflow selector in the OFF position.


Climate Controls

33


34/240

Under normal weather conditions, do not leavethe air flow selector in MAX A/C or OFF when thevehicle is parked. This allows the vehicle tobreathe using the outside air inlet vents.

Do not put objects under the front seats that willinterfere with the air flow to the back seats.

Remove any snow, ice or leaves from the airintake area at the base of the windshield.

Do not place objects on top of theinstrument panel as these objects may

become projectiles in a collision or sudden stop.

REAR WINDOW DEFROSTER

Ensure that the ignitionis in the ON position.Press the control toclear the rear window of thin ice and fog. The LEDwill illuminate.

The defroster turns off automatically after 10minutes or when the ignition is turned OFF. Tomanually turn off the defroster before 10 minutes,push the control again.


Climate Controls

34


35/240

HEADLAMP CONTROL The first position

turns on the parking,tail, license plate andside marker lamps.

The outer positionturns on theheadlamps.

Foglamp control (if equipped)

The foglamps can beturned on when theignition is in the ON

position and theheadlamp control is ineither of the followingpositions:

Parking lamps

Low beams

Press the foglamp control to activate the foglamps.

Press the foglamp control again to deactivate thefoglamps.

When the highbeams are activated, the foglamps willnot operate.

Daytime running lamps (DRL) (if equipped)

Turns the headlamps on with a reduced output. Toactivate:

the ignition must be turned on

the headlamp control is in the OFF or Parkinglamps position

the high beam headlamps must be turned off

the parking brake is released


Lights

35


36/240

Always remember to turn on yourheadlamps at dusk or during inclement

weather. The Daytime Running Light (DRL)System does not activate your tail lamps andgenerally may not provide adequate lighting duringthese conditions. Failure to activate yourheadlamps under these conditions may result in acollision.

High beams

Push the lever towardthe instrument panel toactivate. Pull the lever

towards you todeactivate.

Flash to pass

Pull toward you slightlyto activate and releaseto deactivate.

PANEL DIMMER CONTROL

To adjust thebrightness of the

instrument panel: Rotate

clockwise/counterclockwisewhen the headlampcontrol is in theparking lamp or low-beam position.

To turn on the courtesy lamps:

Rotate fully counterclockwise.

OFF

HI

LO

OFF

HILO


Lights

36


37/240

AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimedat the assembly plant.

If your vehicle has been in an accident the alignmentof your headlamps should be checked by a qualifiedservice technician.

Headlamp vertical aim adjustment

1. Park the vehicle on a level surface approximately7.6 meters (25 feet) from a vertical wall or screendirectly in front of it.

(1) Eight feet

(2) Center height of lamp to ground

(3) Twenty five feet

(4) Horizontalreference line

2. Measure the heightfrom the center of yourheadlamp to theground and mark a 2.4meter (8 foot)horizontal referenceline on the vertical wall or screen at this height (apiece of masking tape works well). The center of thelamp is marked by a 3.0 mm circle on the headlamplens.

3. Turn on the low beam headlamps to illuminate thewall or screen and open the hood.

4. On the wall orscreen you will observea light pattern with flatedges at the top of thebeam pattern. If theflat edges are not atthe horizontalreference line, the beam will need to be adjusted.


Lights

37


38/240

5. Locate the verticaladjuster on eachheadlamp, then use a 6mm allen wrench orscrewdriver to adjustthe headlamp up ordown.

6. HORIZONTAL AIMIS NOT REQUIRED FOR THIS VEHICLE AND ISNON-ADJUSTABLE.

7. Close the hood and turn off the lamps.

TURN SIGNAL CONTROL

Push down to

activate the left turnsignal.

Push up to activatethe right turn signal.

INTERIOR LAMPS

Map lamps (if equipped)

For coupes the maplamps are located onthe interior roof. Press

the controls on eitherside of the lamp toturn the light on.

BULBS

Replacing exterior bulbs

Check the operation of all the bulbs frequently.

OFF

HILO


Lights

38


39/240

Using the right bulbsReplacement bulbs are specified in the chart below.Headlamp bulbs must be marked with an authorizedD.O.T. for North America and an E for Europe toassure lamp performance, light brightness andpattern and safe visibility. The correct bulbs will notdamage the lamp assembly or void the lampassembly warranty and will provide quality bulb burntime.

Function Trade Number

Tail lamp, brakelamp, turn lamp 3157K

Park lamp, turn lamp, side marker

(front)3157 AK (amber)

Backup lamp 3156K

License plate lamp 168

High-mount brakelamp 906

Headlamps 9007

Luggage compartment lamp 906

Dome lamp 575

Map lamp 575

Visor vanity lamp 74

Glove compartment 194

Rearview mirror map lamps 192

Fog lamp 899

All replacement bulbs are clear in color except where

noted.

To replace all instrument panel lights - see your dealer.

Interior bulbs

Check the operation of all bulbs frequently.

Map lamps

For bulb replacement, see a qualified servicetechnician or your dealer.


Lights

39


40/240

Replacing headlamp bulbsTo remove the headlamp bulb:

1. Make sure headlamp switch is in the OFFposition, then open the hood.

2. At the back of theheadlamp, pull tworetainer pins up torelease the headlampassembly.

3. Pull headlampassembly forward anddisconnect theelectrical connector from the bulb by pullingrearward.

4. Remove the bulbretaining ring byrotating itcounterclockwise andslide off the plasticbase.

5. Remove the old bulbfrom the lamp assemblyby pulling it straightout of the lampassembly.

Handle a halogen headlamp bulb carefullyand keep out of childrens reach. Grasp the

bulb only by its plastic base and do not touch theglass. The oil from your hand could cause the bulbto break the next time the headlamps areoperated.

Install the new bulb in reverse order.


Lights

40


41/240

Replacing front parking lamp/turn signal bulbs1. Make sure the headlamp control is in the OFFposition and open the hood.

2. At the back of theheadlamp, pull tworetainer pins up torelease the headlampassembly.

3. Pull headlampassembly forward androtate the bulb socketcounterclockwise and remove from lamp assembly.

4. Pull the bulb straight

out from the socketand push in the newbulb.


Replacing high-mount brakelamp bulbs

1. Make sure theheadlamp switch is inthe OFF position andthen open the trunk.

2. Inside trunk, locateaccess hole under the

rear decklid.3. Rotate the bulbsocketcounterclockwise andpull it out of the lamp assembly.

4. Carefully pull the bulb straight out of socket.



Lights

41


42/240

Replacing foglamp bulbs1. Make sure theheadlamp switch is inthe OFF position.

2. Rotate the foglampbulb socketcounterclockwise andremove from foglamp.

3. Disconnect theelectrical connector and pull the bulb straight out.


Replacing license plate lamp bulbs

1. Make sure theheadlamp switch is inthe OFF position andthen open trunk andremove bulb socketfrom the trunk lid byturning itcounterclockwise.

2. Pull the bulb straight out of the socket.


Replacing tail lamp/backup bulbs

For bulb replacement, see a dealer or qualifiedtechnician.


Lights

42


43/240

MULTI-FUNCTION LEVERWindshield wiper:Rotate the end of thecontrol away from youto increase the intervalspeed of the wipers;rotate towards you todecrease the interval speed of the wipers.

Top two positions are for LO and HI speedconstant wipe.

Windshield washer:Push the end of thestalk:

briefly: causes asingle swipe of the wipers without washer fluid.

a quick push and hold: the wipers will swipe threetimes with washer fluid.

a long push and hold: the wipers and washer fluidwill be activated for up to ten seconds.

CHANGING THE WIPER BLADES

1. Pull the wiper armaway from the vehicle.Turn the blade at anangle from the wiperarm. Push the lock pinmanually to release the

blade and pull thewiper blade downtoward the windshieldto remove it from thearm.

2. Attach the newwiper to the wiper arm and press it into place until aclick is heard.

3. Replace wiper blades every 6 months for optimumperformance.

OFF

HILO

OFF

HILO


Driver Controls

43


44/240

TILT STEERING WHEEL (IF EQUIPPED)To adjust the steeringwheel:

1. Pull and hold thesteering wheel releasecontrol toward you.

2. Move the steeringwheel up or down untilyou find the desiredlocation.

3. Release the steering wheel release control. Thiswill lock the steering wheel in position.

Never adjust the steering wheel when thevehicle is moving.

OVERHEAD STORAGE NET (IF EQUIPPED)

Be sure tosecure objects

when placed in thestorage net in orderto help reduce therisk that theybecome projectiles inthe event of acollision.


Driver Controls

44


45/240

AUXILIARY POWER POINTThe power point is anadditional powersource for electricalaccessories. A powerpoint is located in frontof the center consolestorage bin.

Do not plug optionalelectrical accessories into the cigarette lighter. Usethe power point.

Do not use the power point for operating thecigarette lighter element.

The Maximum power each power point can supply

depends on the fuse rating. For example: a 20A fuseshould supply a maximum of 240 Watts, a 15A fuseshould supply a maximum of 180 Watts and a 10Afuse should supply a maximum of 120 Watts.Exceeding these limits will result in a blown fuse.

Always keep the power point caps closed when notbeing used.

Power outlets are designed for accessory plugsonly. Do not hang any type of accessory oraccessory bracket from the plug. Improper useof the power outlet can cause damage notcovered by your warranty.

POWER WINDOWS

When closingthe power

windows, you shouldverify they are freeof obstructions andensure that childrenand/or pets are not inthe proximity of thewindow openings.


Driver Controls

45


46/240

Press and hold the bottom part of the rocker switchto open the window. Press and hold the top part of

the rocker switch to close the window.

One touch down

Allows the driverswindow to open fullywithout holding thecontrol down. Presscompletely down onthe bottom part of the

rocker switch and release quickly. Press again to

stop.

POWER SIDE VIEW MIRRORS(IF EQUIPPED)

To adjust your mirrors:

1. Move the mirrorselector control all theway to the left toadjust the left mirroror all the way to theright to adjust the rightmirror.

2. Move the control in the direction you wish to tilt

the mirror.

3. Return the control to the center position.

SPEED CONTROL (IF EQUIPPED)

With speed control set, you can maintain a speed of

48 km/h (30 mph) or more without keeping your

foot on the accelerator pedal. Speed control does

not work at speeds below 48 km/h (30 mph).

Do not use the speed control in heavy trafficor on roads that are winding, slippery or

unpaved.


Driver Controls

46


47/240

Setting speed controlThe controls for usingyour speed control arelocated on the steeringwheel for yourconvenience.

1. Press the ON controland release it.

2. Accelerate to the desired speed.

3. Press the SETACCEL control andrelease it.

4. Take your foot off

the accelerator pedal.

Note:

Vehicle speed may vary momentarily when drivingup and down a steep hill.

If the vehicle speed increases above the set speedon a downhill, you may want to apply the brakesto reduce the speed.

If the vehicle speed decreases more than 16 km/h(10 mph) below your set speed on an uphill, yourspeed control will disengage.

Resuming a set speed

Press the RESUMEcontrol and release it.This will automaticallyreturn the vehicle tothe previously setspeed. The RESUMEcontrol will not work ifthe vehicle speed is notfaster than 48 km/h (30 mph).

OFF

ON

RESUME

SET

ACCEL

COAST

RESUME

SET

ACCEL

COAST


Driver Controls

47


48/240

Increasing speed while using speed controlThere are two ways toset a higher speed:

Press and hold theSET ACCEL controluntil you get to thedesired speed, thenrelease the control.You can also use theSET ACCEL control to operate the Tap-Upfunction. Press and release this control toincrease the vehicle set speed in small amountsby 1.6 km/h (1 mph).

Use the accelerator pedal to get to the desired

speed. When the vehicle reaches that speed pressand release the SET ACCEL control.

Reducing speed while using speed control

There are two ways toreduce a set speed:

Press and hold theCOAST control untilyou get to thedesired speed, thenrelease the control.You can also use theCOAST control to operate the Tap-Down function.Press and release this control to decrease thevehicle set speed in small amounts by 1.6 km/h

(1 mph).

Depress the brakepedal until thedesired vehiclespeed is reached,press the SETACCEL control.

Turning off speed control

There are two ways to turn off the speed control:

RESUME

SET

ACCEL

COAST

RESUME

SET

ACCEL

COAST

RESUME

SET

ACCEL

COAST


Driver Controls

48


49/240

Depress the brake pedal or the clutch pedal (ifequipped). This will not erase your vehicles

previously set speed.

Press the speedcontrol OFF control.

Note: When you turnoff the speed control orthe ignition, your speedcontrol set speedmemory is erased.

CENTER CONSOLE

Your vehicle may be equipped with a variety of

console features. These include:

Dual cupholders

Auxiliary power point

Coin holder slots (if equipped)

Convertible top control (if equipped)

Use only soft cups in the cupholder. Hardobjects can injure you in a collision.

Cell phone use

The use of Mobile Communications Equipment has

become increasingly important in the conduct of

business and personal affairs. However, drivers mustnot compromise their own or others safety whenusing such equipment. Mobile Communications canenhance personal safety and security whenappropriately used, particularly in emergencysituations. Safety must be paramount when usingmobile communications equipment to avoid negatingthese benefits.

Mobile Communication Equipment includes, but isnot limited to cellular phones, pagers, portable emaildevices, in vehicle communications systems,telematics devices and portable two-way radios.

OFF

ON


Driver Controls

49


50/240

A drivers first responsibility is the safeoperation of the vehicle. The most important

thing you can do to prevent a crash is to avoiddistractions and pay attention to the road. Waituntil it is safe to operate Mobile CommunicationsEquipment.

POSITIVE RETENTION FLOOR MAT(IF EQUIPPED)

Position the floor mat sothat the eyelet is over thepointed end of theretention post and rotate

forward to lock in. Makesure that the mat does notinterfere with the operationof the accelerator or thebrake pedal. To remove thefloor mat, reverse the installation procedure.

INTERIOR TRUNK CONTROL

The remote trunk release control is located in theglove compartment. Press to open trunk.

CONVERTIBLE (IF EQUIPPED)

Do not store articles behind rear seat. Articlesstored in the convertible top stowage compartmentmay break the rear glass window when the top islowered.

Lowering the convertible top

The convertible top can be lowered with the sidewindows either up or down.

The convertible top will not operate unless theparking brake is engaged. Do not lower the top whilethe vehicle is moving because the top may beseverely damaged. Also, do not lower the top whenthe top material is wet.


Driver Controls

50


51/240

To lower the convertible top:1. Bring vehicle to a complete stop. Engage theparking brake. Key must be in the ON position.

2. Check the convertible top stowage compartmentbehind the rear seat to be sure it is empty and readyto receive the top.

3. Unclamp the top from the windshield header atboth the right and left sides by pulling each clamprearward until the hook in the windshield header isfree. The clamps are flush with the header when inthe closed position.

4. Close the windshield header clamps immediatelyafter disengagement, to avoid cutting the top

material and to permit installation of the vinyl boot.5. If the top has notbeen lowered for sometime and sticks to thewindshield header,push the front of thetop up slightly withyour hand to loosen it.

6. Push the convertibletop switch on theconsole in front of thearmrest and hold untilthe top is completelystored.

7. Disengage theparking brake.

Installation of the boot (if equipped)

1. Push boot rearwardand engage boot underthe body molding atthe rear and sides.

SE

TPAR

K BRAKE


Driver Controls

51


52/240

2. Fasten boot toquarter trim panel withsnap or pivot latch onboth sides of thevehicle.

3. Insert boot tongueinto groove located onrear of seat.

4. To remove, unfastenthe snaps or pivotlatches and the boottongue.

5. Pull forward and liftoff.

Raising the convertible top

The convertible top will not operate unless theparking brake is engaged. Do not raise the top while

the vehicle is moving because the top may beseverely damaged.

To raise the convertible top:

1. Bring the vehicle to a complete stop. Engage theparking brake. Key must be in the ON position.

2. Remove the boot cover and store it in the luggagecompartment.

3. Lower the front and rear side windows.

4. Push the convertible top button, holding it untilthe top unfolds and moves forward toward thewindshield header.


Driver Controls

52


53/240

5. Open both top clamps before the top meets thewindshield header

6. Continue to use the top motor to raise the topuntil it has reached the fully closed position flush tothe header.

7. The two pins under the forward edge of the topshould seat themselves in the matching holes in theheader.

8. To fasten both clamps securely, push the clamphandles into the header on the top until they areflush with the header. Pulling down on the header atthe center grip while closing the latches may assistin fastening the clamps.

9. Raise the front and rear side windows.

10. Disengage the parking brake.


Driver Controls

53


54/240

KEYSThe key operates all locks on your vehicle. In case ofloss, replacement keys are available from yourdealer.

You should always carry a second key with you in asafe place in case you require it in an emergency.

Refer to SecuriLock Passive Anti-Theft Systemfor more information.

POWER DOOR LOCKS

Press U to unlock alldoors and L to lock alldoors.

INTERIOR LUGGAGE COMPARTMENTRELEASE

Your vehicle is equipped with a mechanical interiorluggage compartment release handle that provides ameans of escape for children and adults in the eventthey become locked inside the luggagecompartment.

Adults are advised to familiarize themselves with the

operation and location of the release handle.

U L


Locks and Security

54


55/240

To open the luggagecompartment door (lid)from within theluggage compartment,pull the illuminated Tshaped handle andpush up on the trunklid. The handle iscomposed of a materialthat will glow for hoursin darkness followingbrief exposure toambient light.

The T shaped handle will be located either on theluggage compartment door (lid) or inside theluggage compartment near the tail lamps.

Keep vehicledoors and

luggage compartmentlocked and keep keysand remotetransmitters out of achilds reach.Unsupervisedchildren could lockthemselves in thetrunk and risk injury.Children should be

taught not to play invehicles.


Locks and Security

55


56/240

On hot days, the temperature in the trunkor vehicle interior can rise very quickly.

Exposure of people or animals to these hightemperatures for even a short time can causedeath or serious heat-related injuries, includingbrain damage. Small children are particularly atrisk.

REMOTE ENTRY SYSTEM

This device complies with part 15 of the FCC rules

and with RS-210 of Industry Canada. Operation is

subject to the following two conditions: (1) This

device may not cause harmful interference, and (2)

This device must accept any interference received,

including interference that may cause undesired

operation.

Changes or modifications not expressly

approved by the party responsible for

compliance could void the users authority tooperate the equipment.

Your vehicle is equipped with a remote entry systemwhich allows you to:

unlock the vehicledoors without a key.

lock all the vehicledoors without a key.

activate the personalalarm.

release the decklid.

These features will not operate when the ignition isin the RUN or START position.

If there is any potential remote keyless entryproblem with your vehicle, ensure ALL remoteentry transmitters are taken to the dealership, toaid in troubleshooting.


Locks and Security

56


57/240

Unlocking the doors1. Press and release to unlock the drivers door.Note: The interior lamps will illuminate.

2. Press and release again within three secondsto unlock the passenger door.

Locking the doors

1. Press and release to lock all the doors. Note:The interior lamps will turn off (unless the domelamp control is in the full-up position), and theheadlamps and parking lamps will flash.

2. Press and release again within three seconds

to confirm that all the doors are closed and locked.

Note: The doors will lock again, the horn will chirponce and the headlamps and parking lamps willflash.

If any of the doors are not properly closed the hornwill make two quick chirps.

Sounding a panic alarm

Press to activate the alarm. The horn will

sound for a maximum of 30 seconds and theparklamps will flash for a maximum of 3 minutes.Press again or turn the ignition to ON to deactivate,or wait for the alarm to timeout in 3 minutes.

Note: The panic alarm will only operate when theignition is in the OFF or ACC position.

Opening the trunk

Press once to open the trunk.

Ensure that the trunk is closed and latched beforedriving your vehicle. Failure to properly latch thetrunk may cause objects to fall out or block thedrivers rear view.

Replacing the battery

The remote entry transmitter uses one coin typethree-volt lithium battery CR2032 or equivalent. The


Locks and Security

57


58/240

typical operating range for your remote entrytransmitter is approximately 10 meters (33 feet). Adecrease in the operating range could be caused by:

weather conditions,

nearby radio towers,

structures around the vehicle and

other vehicles parked next to the vehicle.

To replace the battery:

1. Twist a thin coinbetween the two halvesof the remote entrytransmitter near thekey ring. DO NOTTAKE THE RUBBERCOVER AND CIRCUITBOARD OFF THE FRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER.

2. Do not wipe off anygrease on the batteryterminals on the backsurface of the circuitboard.

3. Remove the old battery.

4. Insert the new battery. Refer to the diagram

inside the remote entry transmitter for the correctorientation of the battery. Press the battery down toensure that the battery is fully seated in the batteryhousing cavity.

5. Snap the two halves back together.

Note: Replacement of the battery will not cause theremote transmitter to become deprogrammed fromyour vehicle. The remote transmitter should operatenormally after battery replacement.

Replacing lost remote entry transmittersIf you would like to have your remote entrytransmitter reprogrammed because you lost one, or


Locks and Security

58


59/240

would like to buy additional remote entrytransmitters, you can either reprogram themyourself, or take all remote entry transmitters toyour authorized dealer for reprogramming.

How to reprogram your remote entrytransmitters

You must have all remote entry transmitters(maximum of four) available before beginning thisprocedure.

To reprogram theremote entrytransmitters:

1. Ensure the vehicle is

electronically unlocked.2. Put the key in theignition.

3. Turn the key from the 2 (LOCK) position to 3(OFF).

4. Cycle eight times rapidly (within 10 seconds)between the 3 (OFF) position and 4 (ON). Note:The eighth turn must end in the 4 (ON) position.

5. The doors will lock, then unlock, to confirm thatthe programming mode has been activated.

6. Within 20 seconds press any button on the remoteentry transmitter. Note: If more than 20 secondshave passed you will need to start the procedure

over again.7. The doors will lock, then unlock, to confirm thatthis remote entry transmitter has been programmed.

8. Repeat Step 6 to program each additional remoteentry transmitter.

9. Turn the ignition to the 3 (OFF) position afteryou have finished programming all of the remoteentry transmitters. Note: After 20 seconds, you willautomatically exit the programming mode.

10. The doors will lock, then unlock, to confirm thatthe programming mode has been exited.

3

1

2

5

4


Locks and Security

59


60/240

Illuminated entryThe interior lamps illuminate when the remote entrysystem is used to unlock the door(s) or sound thepersonal alarm.

The illuminated entry system will turn off theinterior lights if:

the ignition switch is turned to the ON position,or

the remote transmitter lock control is pressed, or

after 25 seconds of illumination.

The dome lamp control (if equipped) must not beset to the OFF position for the illuminated entrysystem to operate.

The inside lights will not turn off if: they have been turned on with the dimmer

control, or

any door is open.

The battery saver will shut off the interior lamps 30minutes after the ignition has been turned to theOFF position, 10 minutes after if the last door is leftopen, and 30 minutes after if the trunk is left openor the dome lamp switch is left on.

SECURILOCK PASSIVE ANTI-THEFT SYSTEM

SecuriLock passive anti-theft system is an engineimmobilization system. This system is designed to

prevent the engine from being started unless acoded key programmed to your vehicle is used.The use of the wrong type of coded key may lead toa no-start condition.

Your vehicle comes with two coded keys; additionalcoded keys may be purchased from your dealer. Thedealer can program your spare keys to your vehicleor you can program the keys yourself. Refer toProgramming spare keys for instructions on howto program the coded key.

Note: The SecuriLock passive anti-theft system isnot compatible with non-Ford aftermarket remote


Locks and Security

60


61/240

start systems. Use of these systems may result invehicle starting problems and a loss of securityprotection.

Note: Large metallic objects, electronic devices thatare used to purchase gasoline or similar items, or asecond coded key on the same key chain may causevehicle starting issues. You need to prevent theseobjects from touching the coded key while startingthe engine. These objects will not cause damage tothe coded key, but may cause a momentary issue ifthey are too close to the key when starting theengine. If a problem occurs, turn the ignition off,remove all objects on the key chain away from thecoded key and restart the engine.

Theft indicator

The theft indicator is located in the instrumentcluster.

When the ignition is in the OFF position, theindicator will flash once every 2 seconds toindicate the SecuriLock system is functioning asa theft deterrent.

When the ignition is in the ON position, theindicator will glow for 3 seconds, then turn off toindicate normal system functionality.

If a problem occurs with the SecuriLock system,the indicator will flash rapidly or glow steadily whenthe ignition is in the ON position. If this occurs, thevehicle should be taken to an authorized dealer for

service.

Automatic arming

The vehicle is armedimmediately afterswitching the ignitionto the 3 (OFF)position.

The THEFT indicator

will flash every twoseconds when thevehicle is armed.

3

2

1

5

4


Locks and Security

61


62/240

Automatic disarmingSwitching the ignition to the 4 (ON) position with a

coded key disarms the vehicle.

The THEFT indicator will illuminate for three

seconds and then go out.

If the THEFT indicator stays on for an extended

period of time or flashes rapidly, have the system

serviced by your dealer.

Replacement keys

If your keys are lost or stolen and you dont have an

extra coded key, you will need to have your vehicle

towed to a dealership. The key codes need to beerased from your vehicle and new coded keys will

need to be programmed.

Replacing coded keys can be very costly. Store an

extra programmed key away from the vehicle in a

safe place to help prevent any inconveniences.

Please visit an authorized dealer to purchase

additional spare or replacement keys.

Programming spare keys

You can program your own coded keys to your

vehicle. Please read and understand the entireprocedure before you begin.

Tips: A maximum of eight keys can be coded to your

vehicle.

Only use Securilock keys.

You must have two previously programmed codedkeys (keys that already operate your vehiclesengine) and the new unprogrammed key(s)readily accessible.

If no previously programmed coded keys areavailable, you must take your vehicle to yourdealer to have the spare key(s) programmed.


Locks and Security

62


63/240

1. Insert a previouslyprogrammed coded keyinto the ignition.

2. Turn the ignitionfrom the 3 (OFF)position to the 4 (ON)position. Keep theignition in the 4 (ON)position for at least one second, but no more than10 seconds.

3. Turn the ignition to the 3 (OFF) position, andremove the coded key from the ignition.

4. Within ten seconds of removing the previouslyprogrammed coded key, insert the other previouslyprogrammed coded key into the ignition.

5. Turn the ignition from the 3 (OFF) position to the4 (ON) position. Keep the ignition in the 4 (ON)position for at least one second but not more than10 seconds.

6. Turn the ignition to the 3 (OFF) position, andremove the second key from the ignition.

7. Within twenty seconds of removing the previouslyprogrammed coded key, insert the unprogrammedkey (new/valet key) into the ignition.

8. Turn the ignition from the 3 (OFF) position to the4 (ON) position. Keep the ignition in the 4 (ON)position for at least one second.

9. Your new unprogrammed key is now programmed.If the key has been successfully programmed it willstart the vehicles engine and the theft indicator lightwill illuminate for three seconds and then go out. Ifthe key was not successfully programmed, it will notstart your vehicles engine and the theft indicatorlight will flash on and off rapidly. If failure repeats,bring your vehicle to your dealer to have the newkey(s) programmed.

To program additional new unprogrammed key(s),repeat this procedure from step 1 for each additionalkey.

3

2

1

5

4


Locks and Security

63


64/240

SEATINGNotes:

Reclining the seatback can cause anoccupant to slide under the seats safety

belt, resulting in severe personal injuries in theevent of a collision.

Do not pile cargo higher than the seatbacksto reduce the risk of injury in a collision or

sudden stop.

Adjustable head restraints

Head restraints help to limit head motion in theevent of a rear collision. Adjust your head restraintso that it is located directly behind your head or asclose to that position as possible.

The head restraints canbe moved up anddown.

4way head restraints (if equipped)

Your vehicle may have

head restraints thatcan be moved in fourdirections:

up and down

forward or backward

Adjusting the front manual seat (if equipped)

Never adjust the drivers seat or seatbackwhen the vehicle is moving.


Seating and Safety Restraints

64


65/240

Always drive and ride with your seatbackupright and the lap belt snug and low across

the hips.

Lift handle to moveseat forward orbackward.

Pull lever up to adjustseatback.

Using the power lumbar support (if equipped)

The power lumbarcontrol is located onthe outboard side ofthe seat.

Press one side of thecontrol to adjust

firmness.Press the other side of the control to adjustsoftness.

Adjusting the front power seat (if equipped)

Never adjust the drivers seat or seatbackwhen the vehicle is moving.

Do not pile cargo higher than the seatbacksto avoid injuring people in a collision or

sudden stop.



65


66/240


the hips.

Reclining the seatback can cause anoccupant to slide under the seats safety

belt, resulting in severe personal injuries in theevent of a collision.

The control is located on the front of the driver sseat.

Press front to raise orlower the front portion

of the seat cushion.

Press rear to raise orlower the rear portionof the seat cushion.

Press the control tomove the seat forward,backward, up or down.



66


67/240

REAR SEATSUse the seatbackrelease to fold the backof the front seatforward for rear seatpassenger entry or exit.This release handle islocated on the loweroutboard back of theseat. The seatbacklocks automatically when returned to the normalposition.The rotating boot on the front seat belt is designedto allow rear seat entry/exit. To enter the rear seat:

1. Remove safety beltfrom safety belt guideon top of front seat.

2. Rotate the safetybelt boot rearward.

3. Enter the rear seat in front of the safety belt.4. Rotate the safety belt boot forward and place thebelt in the belt guide on the seat back to allow useby the front driver/passenger.

2nd seat/split-folding rear seatOne or both rear seatbacks can be folded down to

provide additional cargo space.To lower theseatback(s) from insidethe vehicle, pull tab torelease seat back andthen fold seatbackdown.

When raising the seatback(s), make sure you hearthe seat latch into place.



67


68/240

SAFETY RESTRAINTS

Safety restraints precautions


the hips.

To reduce the risk of injury, make surechildren sit where they can be properly

restrained.

Never let a passenger hold a child on his orher lap while the vehicle is moving. The

passenger cannot protect the child from injury in acollision.

All occupants of the vehicle, including thedriver, should always properly wear their

safety belts, even when an air bag (SRS) isprovided.

It is extremely dangerous to ride in a cargoarea, inside or outside of a vehicle. In a

collision, people riding in these areas are morelikely to be seriously injured or killed. Do not allowpeople to ride in any area of your vehicle that isnot equipped with seats and safety belts. Be sureeveryone in your vehicle is in a seat and using asafety belt properly.

In a rollover crash, an unbelted person issignificantly more likely to die than a person

wearing a safety belt.



68


69/240

Each seating position in your vehicle has aspecific safety belt assembly which is made

up of one buckle and one tongue that are designedto be used as a pair. 1) Use the shoulder belt onthe outside shoulder only. Never wear the shoulderbelt under the arm. 2) Never swing the safety beltaround your neck over the inside shoulder. 3)Never use a single belt for more than one person.

Always transport children 12 years old andunder in the back seat and always properly

use appropriate child restraints.

Safety belts and seats can become hot in avehicle that has been closed up in sunnyweather; they could burn a small child. Check seatcovers and buckles before you place a childanywhere near them.

Combination lap and shoulder belts

Before fastening thesafety belt, make surethe shoulder beltpasses through the beltguide on the top of theseatback.

Coupe shown,

convertible is similarand safety belt must also pass through the beltguide.

1. Insert the belttongue into the properbuckle (the buckleclosest to the directionthe tongue is comingfrom) until you hear asnap and feel it latch.Make sure the tongueis securely fastened in the buckle.



69


70/240

2. To unfasten, pushthe release button andremove the tonguefrom the buckle.

Energy Management Feature

This vehicle has a safety belt system with anenergy management feature at the front seatingpositions to help further reduce the risk of injuryin the event of a head-on collision.

This safety belt system has a retractor assemblythat is designed to pay out webbing in acontrolled manner. This feature is designed tohelp reduce the belt force acting on theoccupants chest.

After any vehicle collision, the safety beltsystem at all outboard seating positions

(except driver, which has no automatic lockingretractor feature) must be checked by a qualifiedtechnician to verify that the automatic lockingretractor feature for child seats is still functioningproperly. In addition, all safety belts should bechecked for proper function.

BELT AND RETRACTOR ASSEMBLY MUSTBE REPLACED if the safety belt assembly

automatic locking retractor feature or any othersafety belt function is not operating properly whenchecked according to the procedures in WorkshopManual.

Failure to replace the Belt and Retractorassembly could increase the risk of injury in

collisions.



70


71/240

The front and rear outboard safety restraints in thevehicle are combination lap and shoulder belts. Thefront passenger and rear seat outboard safety beltshave two types of locking modes described below:

Vehicle sensitive mode

This is the normal retractor mode, which allows freeshoulder belt length adjustment to your movementsand locking in response to vehicle movement. Forexample, if the driver brakes suddenly or turns acorner sharply, or the vehicle receives an impact ofapproximately 8 km/h (5 mph) or more, thecombination safety belts will lock to help reduceforward movement of the driver and passengers.

Automatic locking mode

The automatic locking mode is not available on thedriver safety belt.

When to use the automatic locking mode

In this mode, the shoulder belt is automaticallypre-locked. The belt will still retract to remove anyslack in the shoulder belt. The automatic lockingmode is not available on the driver safety belt.

This mode should be used any time a child safetyseat is installed in a passenger front or outboardrear seating position. Children 12 years old andunder should be properly restrained in the rear seat

whenever possible. Refer to Safety restraints forchildren or Safety seats for children later in thischapter.



71


72/240

How to use the automatic locking mode Buckle the

combination lap andshoulder belt.

Grasp the shoulder

portion and pulldownward until theentire belt is pulledout.

Allow the belt to retract. As the belt retracts, you

will hear a clicking sound. This indicates thesafety belt is now in the automatic locking mode.

How to disengage the automatic locking mode

Ford Motor Company recommends that allsafety belt assemblies and attaching

hardware should be inspected by a qualifiedtechnician after any collision. Safety beltassemblies not in use during a collision should alsobe inspected and replaced if either damage orimproper operation is noted.



72


73/240

Disconnect the combination lap/shoulder belt andallow it to retract completely to disengage theautomatic locking mode and activate the vehiclesensitive (emergency) locking mode.

After any vehicle collision, the frontpassenger and rear outboard seat belt

systems must be checked by a qualified technicianto verify that the automatic locking retractorfeature for child seats is still functioning properly.In addition, all seat belts should be checked forproper function.

BELT AND RETRACTOR ASSEMBLY MUST

BE REPLACED if the seat belt assemblyautomatic locking retractor feature or any otherseat belt function is not operating properly whenchecked according to the procedures in WorkshopManual.

Failure to replace the Belt and Retractorassembly could increase the risk of injury in

collisions.

Safety belt warning light and indicatorchime

The safety belt warning light illuminates in theinstrument cluster and a chime sounds to remindthe occupants to fasten their safety belts.



73


74/240

Conditions of operationIf... Then...

The drivers safety belt is

not buckled before theignition switch is turned

to the ON position...

The safety belt warning light

illuminates1-2 minutes and thewarning chime sounds 4-8

seconds.


buckled while the

indicator light is

illuminated and the

warning chime is

sounding...

The safety belt warning lightand warning chime turn off.


buckled before the

ignition switch is turned

to the ON position...

The safety belt warning light

will turn on for 3 seconds and

then turn off. The indicator

chime will remain off.

BeltMinder

The BeltMinder feature is a supplemental warning tothe safety belt warning function. This featureprovides additional reminders to the driver that thedrivers safety belt is unbuckled by intermittentlysounding a chime and ill

Documents

04 Mustang Manual