011068 Loudspeaker 2

CyberData Corporation 3 Justin Court, Monterey, CA 93940 831.373.2601 Fax: 831.373.4193 www.cyberdata.net

The IP Endpoint Company

Mini Horn Loudspeaker The IP Endpoint Company

Features

A small re-entrant horn package with a powerful and efficient compression driver.

Designed for good speech intelligibility. Rated at 40 watts continuous duty using a 1-1/2 diameter 8 or 45 ohm voice coil on a rugged phenolic diaphragm. A heat sink coupled to the driver dissipates

heat to maintain efficiency and endurance.

Weather and corrosion resistant design uses stainless fasteners. Plating on driver meets 96-hour salt spray test. Other parts are made of impact and UV resistant ABS.

Adjustable mounting base will attach to a 3- inch electrical box.

Flange holes allow for recessed or concealed mounting.

Dimensions

Specifications

Sound Pressure Level(At 1 meter)

1 watt, 500 -5000 Hz, averaged; 107 dB

1 watt, 1 octave at 2 kHz, averaged; 108 dB

40 watts, 1 octave at 2 kHz, averaged; 123 dB

Dimensions 7 .6" H x 5.5" W x 4.8" D

Input Impedance 8 ohms nominal

Frequency Range

2 Years LimitedWarranty

Power Handling 40 watts continuous duty

Net Weight 2.5 lbs. (1.14 kg.)

700-6500 Hz (3 dB)(On Axis) 500-7000 Hz (6 dB)

Mounting Provisions Adjustable base has four slots on 2-3/4diameter for #8 screws. Horn flange has 4 holes on 5-5/8diameter (4 squarepattern) for #8 screws.

2.8 lbs.Boxed Weight

011068Part Number

Operating Temperature -30 F to 160 F (-34 C to 71 C)IP Rating IP54


Mini Horn Loudspeaker

930312H/130604

Generic 802.3at PoE Switch

IP-PBX ServerIP Phone

Typical Installation - PoE 802.3at

1 2 3 4 5 6

011068 Loudspeaker

(up to 25 watts)

High Power PoE Switch

IP-PBX ServerIP Phone

Typical Installation - High Power PoE Injector

1 2 3 4 5 6

011068 Loudspeaker

(up to 25 watts)

Non-PoE Switch

PoE Injector(High power, 802.3at)


Mini Horn Loudspeaker

930312I/141208

Using the Amplified Outputs - Low Power Mode

Using the Amplified Outputs - High Power ModeNote: You can use an 802.3atcompliance switch instead of an802.3at power injector and hub

802.3at PoE Injector (high power hub)

Cat 5 Ethernet Cable

Non-PoE Ethernet Switch

*Note: The positive (+) wire coming from the speaker may be red or white. The negative (-) wire is black.

Use 16 gauge wire coming out of screw terminals.

Note: Make sure that the wire length going to the wire nuts is kept short (approximately 6 inches).

Optional 2 Speaker Configuration(802.3at mode)

8 Ohms

Standard 1 Speaker Configuration(802.3af mode)

8 Ohms

16 gauge wire

25 feet maximum distance

Twist wire nuts2 speakers in parallel (4 Ohm total)

Note: Use wire nuts to connect wire from the speakers to 16 gauge wire.

Standard 1 Speaker Configuration(802.3af mode)

8 Ohms

Use 16 gauge wire coming out of screw terminals.

Note: Make sure that the wire length going to the wire nuts is kept short (approximately 6 inches).

*Note: The positive (+) wire coming from the speaker may be red or white. The negative (-) wire is black.

Non-PoE Ethernet Switch

16 gauge wire

Cat 5 Ethernet Cable

802.3at PoE Injector (high power hub)

Note: You can use an 802.3atcompliance switch instead of an802.3at power injector and hub

*

*

Documents

011068 Loudspeaker 2