PP-DLW - Asusdlcdnet.asus.com/pub/ASUS/mb/Socket604/pp-dlw/e1173_pp-dlw.pdfiii Features Contents Notices .....vi Safety information ..... vii

Mot

herb

oard

PP-DLW

User Guide

ii

Checklist

Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved.No part of this manual, including the products and software described in it, may bereproduced, transmitted, transcribed, stored in a retrieval system, or translated into anylanguage in any form or by any means, except documentation kept by the purchaser forbackup purposes, without the express written permission of ASUSTeK COMPUTER INC.(“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified oraltered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2)the serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIESOR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BELIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES(INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USEOR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT ORERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHEDFOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIMEWITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS.ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS ORINACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTSAND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registeredtrademarks or copyrights of their respective companies, and are used only for identification orexplanation and to the owners’ benefit, without intent to infringe.

E1173

First Edition V1January 2003

iii

Fea

ture

s

ContentsNotices ........................................................................................... viSafety information ......................................................................... viiAbout this guide ............................................................................ viiiASUS contact information ............................................................... xPP-DLW specifications summary ................................................... xi

Chapter 1: Product introduction1.1 Welcome! ........................................................................... 1-1

1.2 Package contents ............................................................... 1-1

1.3 Special features .................................................................. 1-21.3.1 Product highlights .................................................. 1-21.3.2 Value-added solutions ............................................ 1-4

Chapter 2: Hardware information2.1 Motherboard installation ..................................................... 2-1

2.1.1 Placement direction ............................................... 2-12.1.2 Screw holes ........................................................... 2-1

2.2 Motherboard layout ............................................................ 2-2

2.3 Before you proceed ............................................................ 2-3

2.4 Central Processing Unit (CPU) ........................................... 2-42.4.1 Overview ................................................................ 2-42.4.2 Installing the CPU .................................................. 2-52.4.3 Installing the CPU heatsink and fan ....................... 2-6

2.5 System memory ................................................................. 2-82.5.1 Overview ................................................................ 2-82.5.2 Memory Configurations .......................................... 2-92.5.3 Installing a DIMM ................................................. 2-102.5.4 Removing a DIMM ............................................... 2-10

2.6 Expansion slots .................................................................2-112.6.1 Installing an expansion card .................................2-112.6.2 Configuring an expansion card .............................2-112.6.3 PCI slots .............................................................. 2-132.6.4 AGP Pro 8x slot ................................................... 2-13

2.7 Jumpers ............................................................................ 2-14

2.8 Connectors ....................................................................... 2-18

Chapter 3: Powering up3.1 Starting up for the first time ................................................ 3-1

3.2 Powering off the computer ................................................. 3-1

iv

Chapter 4: BIOS setup4.1 Managing and updating your BIOS .................................... 4-1

4.2 BIOS Setup program .......................................................... 4-24.2.1 BIOS menu screen ................................................ 4-34.2.2 Menu bar ................................................................ 4-34.2.3 Navigation keys ..................................................... 4-44.2.4 General help .......................................................... 4-44.2.5 Sub-menu .............................................................. 4-44.2.6 Scroll bar ................................................................ 4-44.2.7 Pop-up window ...................................................... 4-4

4.3 Main menu .......................................................................... 4-54.3.1 AMI BIOS ............................................................... 4-54.3.2 Processor ............................................................... 4-54.3.3 System Memory ..................................................... 4-54.3.4 System Time [xx:xx:xxxx] ....................................... 4-54.3.5 System Date [Day xx/xx/xxxx] ............................... 4-5

4.4 Advanced menu ................................................................. 4-64.4.1 CPU Configuration ................................................. 4-64.4.2 IDE Configuration .................................................. 4-74.4.3 Floppy Configuration ............................................ 4-104.4.4 Super IO Configuration ........................................ 4-104.4.5 ACPI Configuration .............................................. 4-124.4.6 USB Configuration ............................................... 4-144.4.7 System Health Configuration ............................... 4-15

4.5 PCI PnP menu .................................................................. 4-164.5.1 Plug & Play O/S [No] ........................................... 4-164.5.2 PCI Latency Timer [64] ........................................ 4-164.5.3 Pallete Snooping [Enabled] ................................. 4-164.5.4 Slot 1/2/3/4/5 Option ROM Keep [Enabled] ......... 4-174.5.5 Onboard LAN Option ROM Keep [Enabled] ........ 4-17

4.6 Boot menu ........................................................................ 4-184.6.1 Boot Settings Configuration ................................. 4-184.6.2 Boot Device Priority ............................................. 4-204.6.3 Hard Disk Drives .................................................. 4-204.6.4 Removable Drives ............................................... 4-214.6.5 ATAPI CDROM Drives ......................................... 4-21

4.7 Security menu .................................................................. 4-224.7.1 Change Supervisor Password ............................. 4-224.7.2 User Access Level (Full Access] .......................... 4-234.7.3 Change User Password ....................................... 4-234.7.4 Clear User Password ........................................... 4-23

v

4.7.5 Password Check [Setup] ..................................... 4-244.7.6 Boot Sector Virus Protection [Disabled] ............... 4-244.7.7 Clear Chassis Intrusion [Ignore] .......................... 4-24

4.8 Chipset menu ................................................................... 4-254.8.1 Configure Advanced Settings for NorthBridge ..... 4-254.8.2 Intel ICH4 SouthBridge Configuration .................. 4-264.8.3 Intel PCI-64 Hub 2 Configuration ......................... 4-27

4.9 Power menu ..................................................................... 4-28

4.10 Exit menu ......................................................................... 4-30

Chapter 5: OS installation5.1 Support CD contents .......................................................... 5-1

5.1.1 Drivers ................................................................... 5-15.1.2 Management Sofware ............................................ 5-15.1.3 Utilities ................................................................... 5-25.1.4 Contact .................................................................. 5-2

5.2 Microsoft® Windows® NT Server 4.0 ................................. 5-35.2.1 Intel® 82540EM LAN driver installation ................. 5-3

5.3 Microsoft® Windows® 2000 Server ................................... 5-65.3.1 Intel® 82540EM LAN driver installation ................. 5-65.3.2 SoundMAX audio driver and appl. installation ....... 5-95.3.3 USB 2.0 driver installation ................................... 5-105.3.4 Enabling ATA100 Feature in Windows® 2000 ..... 5-10

5.4 Microsoft®Windows® XP Professional .............................5-115.4.1 Intel 82540EM LAN driver installation ...................5-115.4.2 SoundMAX audio driver and appl. installation ..... 5-165.4.3 USB 2.0 driver installation ................................... 5-18

5.5 Novell® NetWare® Server ............................................... 5-225.5.1 Intel® 82540EM LAN Driver Installation .............. 5-22

5.6 SUN Solaris 7 Server ....................................................... 5-245.6.1 Intel® 82540EM LAN Driver Installation .............. 5-24

5.7 SCO Open Server 5.0.x ................................................... 5-245.7.1 Intel® 82540EM LAN Driver Installation .............. 5-24

5.8 SCO UnixWare Server ..................................................... 5-255.8.1 Intel® 82540EM LAN Driver Installation .............. 5-25

5.9 Linux RedHat 7.x .............................................................. 5-265.9.1 Intel 82540EM LAN Driver Installation ................. 5-26

vi

Notices

Federal Communications Commission Statement

This device complies with FCC Rules Part 15. Operation is subject to thefollowing two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received including interferencethat may cause undesired operation.

This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmful interferencein a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance withmanufacturer’s instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that towhich the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noiseemissions from digital apparatus set out in the Radio InterferenceRegulations of the Canadian Department of Communications.

This class B digital apparatus complies with Canadian ICES-003.

The use of shielded cables for connection of the monitor to thegraphics card is required to assure compliance with FCC regulations.Changes or modifications to this unit not expressly approved by theparty responsible for compliance could void the user’s authority tooperate this equipment.

vii

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable fromthe electrical outlet before relocating the system.

• When adding or removing devices to or from the system, ensure thatthe power cables for the devices are unplugged before the signalcables are connected. If possible, disconnect all power cables from theexisting system before you add a device.

• Before connecting or removing signal cables from the motherboard,ensure that all power cables are unplugged.

• Seek professional assistance before using an adpater or extensioncord. These devices could interrupt the grounding circuit.

• Make sure that your power supply is set to the correct voltage in yourarea. If you are not sure about the voltage of the electrical outlet youare using, contact your local power company.

• If the power supply is broken, do not try to fix it by yourself. Contact aqualified service technician or your retailer.

Operation safety• Before installing the product and adding devices on it, carefully read all

the documentation that came with the package.

• Before using the product, make sure all cables are correctly connectedand the power cables are not damaged. If you detect any damage,contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away fromconnectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place theproduct in any area where it may become wet.

• Place the product on a stable surface.

• If you encounter technical problems with the product, contact aqualified service technician or your retailer.

viii

About this guideThis user guide contains the information you need when installing theASUS PP-DLW motherboard.

How this guide is organizedThis manual contains the following parts:

• Chapter 1: Product introductionThis chapter describes the features of the PP-DLW motherboard. Itincludes brief descriptions of the special attributes of the motherboardand the new technology it supports.

• Chapter 2: Hardware informationThis chapter lists the hardware setup procedures that you have toperform when installing system components. It includes description ofthe switches, jumpers, and connectors on the motherboard.

• Chapter 3: Powering upThis chapter describes the power up sequence and gives informationon the BIOS beep codes.

• Chapter 4: BIOS setupThis chapter tells how to change system settings through the BIOSSetup menus. Detailed descriptions of the BIOS parameters are alsoprovided.

• Chapter 5: Driver installationThis chapter tells how to install LAN, USB 2.0, and audio drivers undervarious operating systems.

ix

Conventions used in this guideTo make sure that you perform certain tasks properly, take note of thefollowing symbols used throughout this manual.

Where to find more informationRefer to the following sources for additional information and for productand software updates.

1. ASUS WebsitesThe ASUS websites worldwide provide updated information on ASUShardware and software products. The ASUS websites are listed in theASUS Contact Information on page x.

2. Optional DocumentationYour product package may include optional documentation, such aswarranty flyers, that may have been added by your dealer. Thesedocuments are not part of the standard package.

WARNING: Information to prevent injury to yourself when tryingto complete a task.

CAUTION: Information to prevent damage to the componentswhen trying to complete a task.

IMPORTANT: Information that you MUST follow to complete atask.

NOTE: Tips and additional information to aid in completing a task.

x

ASUS contact informationASUSTeK COMPUTER INC. (Asia-Pacific)Address: 150 Li-Te Road, Peitou, Taipei, Taiwan 112General Tel: +886-2-2894-3447General Fax: +886-2-2894-3449General Email: [email protected]

Technical SupportMB/Others (Tel): +886-2-2890-7121 (English)Notebook (Tel): +886-2-2890-7122 (English)Desktop/Server (Tel): +886-2-2890-7123 (English)Support Fax: +886-2-2890-7698Support Email: [email protected] Site: www.asus.com.tw

ASUS COMPUTER INTERNATIONAL (America)Address: 6737 Mowry Avenue, Mowry Business Center,

Building 2, Newark, CA 94560, USAGeneral Fax: +1-510-608-4555General Email: [email protected]

Technical SupportSupport Fax: +1-510-608-4555General Support: +1-502-933-8713Web Site: www.asus.comSupport Email: [email protected]

ASUS COMPUTER GmbH (Germany and Austria)Address: Harkortstr. 25, 40880 Ratingen, BRD, GermanyGeneral Fax: +49-2102-442066General Email: [email protected] (for marketing requests only)

Technical SupportSupport Hotline: MB/Others: +49-2102-9599-0

Notebook (Tel): +49-2102-9599-10Support Fax: +49-2102-9599-11Support (Email): www.asuscom.de/de/support (for online support)Web Site: www.asuscom.de

xi

PP-DLW specifications summary

CPU

Chipsets

Front Side Bus (FSB)

Memory

Onboard LAN

Onboard audio

Expansion slots

Rear panel I/O

Internal connectors

BIOS features

Form Factor

Support CD contents

Support for dual Intel® Xeon™ processor with speeds up to 3.06 GHzOn-die 256KB/512KB L2 cache

Intel E7505 (Placer) MCHIntel ICH4 I/O HubP64H2 PCI-X Hub

533/400 MHz

4 x 184-pin DDR DIMM socketsSupports PC2100/PC1600 unbuffered/registered ECC/non-ECC DDR DIMMsSupports up to 8GB system memory using 2GB DIMMs

Intel® 82540EM Gigabit Ethernet controller

ADI AD1885 2-channel audio CODEC

1 x AGP Pro 8x/4x slot (1.5V only)3 x PCI 64-bit/100MHz 3V (PCI-X1 to PCI-X3)1 x PCI 64-bit/133MHz 3V (PCI-X4)1 x PCI 32-bit/33MHz 5V (PCI1)

1 x Parallel port2 x Serial ports1 x PS/2 keyboard port1 x PS/2 mouse port4 x USB 2.0 ports1 x RJ-45 port (with LED)Line In/Line Out/Microphone ports

2 x ATA/100 IDE connectors1 x Floppy disk connector1 x USB 2.0 connector for two additional USB portsCD/AUX audio connectorsCPU/Power/Chassis fan connectors24-pin, 8-pin SSI power connectorsIDE LED/Power LED connectors20-pin Front panel connectorChassis intrusion, SMBus, WOL, and WOR connectors

4Mb Flash ROM, AMI BIOS with ACPI, DMI, Green, PnPfeatures, and Enhanced Server BIOS features

Extended ATX form factor: 12 in x 10.5 in (30.5 cm x 26.7 cm)

Device driversUtilitiesContact information

* Specifications are subject to change without notice.

Chapter 1

This chapter describes the features of thePP-DLW motherboard. It includes briefexplanations of the special attributes of themotherboard and the new technology itsupports.

Product introduction

ASUS PP-DLW motherboard

Chapter summary

1.1 Welcome! ........................................................ 1-1

1.2 Package contents .......................................... 1-1

1.3 Special features ............................................. 1-2

1.4 Motherboard overview................................... 1-6

ASUS PP-DLW motherboard user guide 1-1

1.1 Welcome!Thank you for buying the ASUS® PP-DLW motherboard!

The ASUS PP-DLW motherboard delivers a host of new features and latesttechnologies making it another standout in the long line of ASUS qualityserver/workstation motherboards!

The PP-DLW incorporates dual Intel® Xeon™ processors in 603/604-pinpackage coupled with the Intel® E7505 chipset to deliver a reliable andhigh performance dual-processor server platform.

Before you start installing the motherboard, and hardware devices on it,check the items in your package with the list below.

1.2 Package contentsCheck your PP-DLW package for the following items.

ASUS PP-DLW motherboardExtended ATX form factor: 12 in x 10.5 in (30.5 cm x 26.7 cm)

ASUS PP-DLW support CD

I/O shield

80-conductor ribbon cable for UltraDMA100/66/33 IDE drives

Ribbon cable for a 3.5-inch floppy drive

Bag of extra jumper caps

PP-DLW User Guide

If any of the above items is damaged or missing, contact your retailer.

1-2 Chapter 1: Product introduction

1.3 Special features

1.3.1 Product highlights

Latest processor technology

The PP-DLW motherboard supports the Intel® Xeon processor via dual604-pin surface mount ZIF sockets. The processor features the Intel®

NetBurst™ micro-architecture that includes Hyper-Threading technology, arapid execution engine, a 533/400MHz system bus, and an execution tracecache to offer a significant increase in performance. See page 2-4 for moreinformation.

DDR memory support

Employing the Double Data Rate (DDR) memory technology, the PP-DLWmotherboard supports up to 8GB of system memory using PC2100/1600unbuffered/registered ECC/non-ECC DDR DIMMs. The ultra-fast 266MHzmemory bus doubles the speed of the PC133 SDRAM to deliver therequired bandwidth for the latest 3D graphics, multimedia, and Internetapplications.

Advanced 64-bit PCI-X slots

The 64-bit/133MHz PCI-X slots onboard maximizes I/O bandwidth for thenext generation 64-bit PCI-X cards that support 133/100MHz bus. ThePCI-X specification 1.0a allows full peer-to-peer transactions between PCIbuses and provides options for intelligent I/O and server managementcards.

AGP Pro 8x/4X slot

The motherboard supports the latest graphic architecture, the AGP Pro/8Xinterface (a.k.a. AGP 3.0), offering 2.1GB/s bandwidth which is twice thatof its predecessor AGP 4X.

Onboard LAN

The motherboard comes with the Intel® 82540EM Gigabit LAN controllerto fully support 10/100/1000BASE-T Gigabit Ethernet Media AccessControl (IEEE 802.3 compliant), and provide Physical Layer Transceiversolution for high performance network applications.


Onboard audio

The ADI AD1885 audio CODEC is onboard to provide a 2-channel audiooutput. This AC’97 audio CODEC provides stereo analog I/O on themotherboard and peripheral devices to deliver high quality audio to PC-connected speakers, headphones, and microphones. The CODECincludes analog-to-digital and digital-to-analog sample rate converters, aspower amplifiers and programmable gain blocks.

ATA/100 IDE support

The dual-channel bus master IDE connectors comply with the ATA/100protocol and supports ATA/100, Multi-Word DMA Mode2, PIO modes 3 & 4IDE devices such as ATAPI IDE CD-ROM, CD-R/RW, ZIP, and LS-120drives.


1.3.2 Value-added solutions

Temperature, fan, and voltage monitoring

The CPU temperature is monitored by the ASUS ASIC to preventoverheating and damage. The system fan rotations per minute (RPM) ismonitored for timely failure detection. The system voltage levels aremonitored to ensure stable supply of current for critical components.

Dual function power switch

While the system is ON, pressing the power switch for less than 4 secondsputs the system to sleep mode or to soft-off mode, depending on the BIOSsetting. Pressing the power switch for more than 4 seconds lets thesystem enter the soft-off mode regardless of the BIOS setting.

Wake-Up support

The motherboard includes Wake-On-LAN, Wake-On-Ring, and BIOSWake-Up features.

ACPI ready

The Advanced Configuration power Interface (ACPI) provides more energysaving features for operating systems that support OS Direct PowerManagement (OSPM).

Concurrent PCI

This feature allows multiple PCI transfers from PCI master buses to thememory and processor.

Chassis intrusion detection

With this feature, the chassis intrusion circuitry logs “chassis-open” eventsinto the system BIOS. The onboard battery supports the chassis intrusiondetection feature even when the normal power is removed.

Smart BIOS

The 4Mbit firmware gives an easy-to-use interface that provides morecontrol and protection to the motherboard. The BIOS has a boot blockwrite protection and HD/SCSI/MO/ZIP/CD/Floppy boot selection, and isYear 2000 certified.


Compliance

Both the BIOS and the hardware levels of the motherboard meet thestringent requirements for SDG 2.0 certification. The new SDG 2.0requirements for systems and components are based on the followinghigh-level goals: support for Plug-and-Play compatibility and powermanagement for configuring and managing all system components, 32-bitdevice drivers, and installation procedures for Windows NT/2000/XP.Color-coded connectors and descriptive icons make identification easy asrequired by the PC ‘99 specification.


1.4 Motherboard overviewBefore you install the PP-DLW motherboard, familiarize yourself with itsphysical configuration and available features to facilitate the motherboardinstallation and future upgrades. A sufficient knowledge of the motherboardspecifications will also help you avoid mistakes that may damage theboard and its components.

1.4.1 Major componentsThe following are the major components of the PP-DLW motherboard aspointed out in the picture on page 1-7.

1. ATX power connector

2. 604-pin CPU sockets

3. Intel® E7505 MCH (Placer)

4. 8-pin 12V SSI power connector

5. DDR DIMM sockets

6. AGP Pro 8X slot

7. Intel® P64H2 PCI-X hub

8. IDE connectors

9. Floppy disk connector

10. Intel® ICH4 I/O hub

11. Flash ROM

12. PCI-X slots (PCI-X1 to PCI-X4)PCI slot (PCI1)

13. ASUS ASIC

14. Standby power LED

15. LPC Super I/O controller

16. Intel® 82540EM Gigabit LANcontroller

17. PS/2 mouse port

18. Parallel port

19. RJ-45 port

20. Line In port

21. Line Out port

22. Microphone port

23. USB 2.0 ports 1 and 2

24. Serial ports

25. USB 2.0 ports 3 and 4

26. Keyboard port

See page 1-8 for the specifications of each component. Refer toChapter 2 for detailed information on the components.


2 5

11

13

1

7

12

15

3

616

4

910 8

14

17 18

26 25 24

20

21

22

23

19


ATX power connector. This 24/20-pin connector is for an ATXpower supply.

604-pin CPU sockets. A 604-pin surface mount, Zero InsertionForce (ZIF) socket for the Intel® Xeon™ processor with 512KB L2cache and a 533/400MHz system bus that allows up to 4.2GBps or3.2GBps data transfer rates. These sockets support Intel XeonCPUs with Hyper-Threading Technology feature.

Intel E7505 MCH (Placer) . The E7505 Memory Controller Hub(MCH) is the host bridge of the Placer chipset which is designed forthe next generation workstation or high-end desktop platforms. TheMCH supports the Intel® Xeon™ processor in dual-processor or uni-processor mode at peak bandwidths of 4.2GBps (533MHz) or3.2GBps (400MHz). The MCH works with the I/O Controller Hub(ICH4) for the I/O subsystem, provides AGP 8x/4x interface(compliant to AGP 3.0 specification), and supports dual-channelDDR SDRAM interface for up to 8GB system memory.

8-pin 12V SSI power connector. This 8-pin connector is for anATX power supply.

DDR DIMM sockets. These four 184-pin DIMM sockets support upto 8GB system memory using unbuffered/registered ECC/non-ECCPC2100/1600 DDR DIMMs.

AGP Pro 8X slot. This Accelerated Graphics (AGP) Pro slotsupports 1.5V AGP 8X mode graphic cards to deliver up to 2.1GB/sbandwidth.

Intel® P64H2 PCI-X hub. The P64H2 is PCI/PCI-X 64-bit Hub 2that provides high-performance I/O capability including 16-bit HubInterface 2.0 connection to MCH, and two independent 64-bit PCI/PCI-X interfaces.

IDE connectors. These dual-channel bus master IDE connectorssupport up to four Ultra DMA/100/66, PIO Modes 3 & 4 IDEdevices. Both the primary (blue) and secondary (black) connectorsare slotted to prevent incorrect insertion of the IDE ribbon cable.

Floppy disk connector. This connector accommodates theprovided ribbon cable for the floppy disk drive. One side of theconnector is slotted to prevent incorrect insertion of the floppy diskcable.

1.4.2 Core specifications

9

8

7

6

5

4

3

2

1


Intel® ICH4 I/O hub. The I/O Controller Hub 4 (ICH4) componentcontains the primary PCI interface, LPC interface, USB 2.0, ATA-100, and other legacy functions. The ICH4 communicates with theMCH via the proprietary interconnect Hub Interface (HI1.5).

Flash ROM. This 4Mb firmware hub contains the programmableBIOS program.

PCI-X/PCI slots. One 64-bit/133MHz PCI-X slots, three 64-bit/100MHz PCI slot, and a 32-bit/33MHz PCI expansion slot supportbus master PCI-X/PCI cards.

ASUS ASIC. This chip performs multiple system functions thatinclude hardware and system voltage monitoring, IRQ routing,among others.

Standby power LED. This LED lights up if there is a standbypower on the motherboard, and serves as a reminder to turn off thesystem power before plugging or unplugging devices.

LPC super I/O controller. This Low Pin Count (LPC) interfaceprovides the commonly used Super I/O functionality. The chipsetsupports UART compatible serial ports, one parallel port with EPPand ECP capabilities, a floppy drive, and PS/2 keyboard andmouse.

Intel® 82540EM Gigabit LAN controller. This LAN controller is asingle-chip solution for LAN on Motherboard (LOM) and NetworkInterface Card (NIC) applications. The chipset provides a 32-bitinterface and supports 10/100/1000 Mbps data transfer rates.

PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse.

Parallel port. This 25-pin port connects a parallel printer, ascanner, or other devices.

RJ-45 port. This port allows connection to a Local Area Network(LAN) through a network hub.

Line In port. This Line In (light blue) port connects a tape player orother audio sources.

Line Out port. This Line Out (lime) port connects a headphone or aspeaker.

Microphone port. This Mic (pink) port connects a microphone.

11

12

13

14

15

16

17

18

10

19

20

21

22


USB 2.0 ports 1 and 2. These 4-pin Universal Serial Bus (USB)ports are available for connecting USB 2.0 devices.

Serial ports. These 9-pin COM1/COM2 ports are for pointingdevices or other serial devices.

USB 2.0 ports 3 and 4. These 4-pin Universal Serial Bus (USB)ports are available for connecting USB 2.0 devices.

PS/2 keyboard port. This purple 6-pin connector is for a PS/2keyboard.

23

24

25

26

Chapter 2

Hardware information

This chapter describes the hardware setupprocedures that you have to perform wheninstalling system components. It includesdetails on the switch/jumper settings andconnector locations on the motherboard.


Chapter summary

2.1 Motherboard installation ............................... 2-1

2.2 Motherboard layout ....................................... 2-2

2.3 Before you proceed ....................................... 2-3

2.4 Central Processing Unit (CPU) ..................... 2-4

2.5 System memory ............................................. 2-8

2.6 Expansion slots ............................................2-11

2.7 Jumpers ........................................................ 2-14

2.8 Connectors ................................................... 2-18


2.1 Motherboard installationBefore you install the motherboard, study the configuration of your chassisto ensure that the motherboard fits into it. The PP-DLW uses the extendedATX form factor that measures 12 in x 10.5 in (30.5 cm x 26.7 cm).

Do not overtighten the screws! Doing so may damage themotherboard.

2.1.1 Placement directionWhen installing the motherboard, make sure that you place it into thechassis in the correct orientation. The edge with external ports goes to therear part of the chassis as indicated in the image below.

2.1.2 Screw holesPlace 9 screws into the holes indicated by circles to secure themotherboard to the chassis.

Make sure to unplug the power cord before installing or removing themotherboard. Failure to do so may cause you physical injury anddamage motherboard components.

Place this side towardsthe rear of the chassis

2-2 Chapter 2: Hardware information

2.2 Motherboard layout

The audio and LAN features are optional. These components aregrayed out in the above motherboard layout.

AudioCodec

24.9cm (9.8in)

30.5

cm (

12in

)

mP

GA

604

mP

GA

604

PP-DLW

PCI-X1 (64-bit, 100MHz 3V)

Accelerated Graphics Port (AGPPRO)




PCI1 (32-bit, 33MHz 5V)

COM1

PAR

AL

LE

L P

OR

T

COM2

PS/2KBMST: MouseB: Keyboard

USB2.0T: USB3B: USB4

Below:Mic In

Center:Line Out

Top:Line In

AT

X_P

OW

ER

FAN3

FAN1

FAN2

Prim

ary

IDE

FLOPPY

4Mbi

tF

lash

BIO

S

Sec

onda

ry ID

E

J31

FAN4

DD

R D

IMM

1 (

72 b

it, 1

84-p

in m

odul

e)

DD

R D

IMM

2 (

72 b

it, 1

84-p

in m

odul

e)

DD

R D

IMM

3 (

72 b

it, 1

84-p

in m

odul

e)

DD

R D

IMM

4 (

72 b

it, 1

84-p

in m

odul

e)

CO

N12

V

AS

US

AS

ICw

ith H

ardw

are

Mon

itor

Intel82540EM

GigabitEthernet

C-M

edia

CMI8

738

6CH

Audi

o Co

ntro

ller

AU

DIO

_CO

M2

AUDIO_COM1

J16

J14

J18

J26GAME1

J20

J28

J29

J5

J1

J12

J24J23

LED

4

J25

J21J22

P64H2PCI-XBridgeHub

IntelE7505MCH

(Placer)

BATTERY1

Intel I/OController

Hub(ICH4)

RJ-45Top:

USB1USB2

Bottom:

J33

BUZZ1

FAN5

26.7cm (10.5in)


2.3 Before you proceedTake note of the following precautions before you install motherboardcomponents or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching anycomponent.

2. Use a grounded wrist strap or touch a safely grounded object or toa metal object, such as the power supply case, before handlingcomponents to avoid damaging them due to static electricity.

3. Hold components by the edges to avoid touching the ICs on them.

4. Whenever you uninstall any component, place it on a groundedantistatic pad or in the bag that came with the component.

5. Before you install or remove any component, ensure that theATX power supply is switched off or the power cord isdetached from the power supply. Failure to do so may causesevere damage to the motherboard, peripherals, and/orcomponents.

When lit, the standby power LED (LED4) indicates that the system isON, in sleep mode, or in soft-off mode, a reminder that you should shutdown the system and unplug the power cable before removing orplugging in any motherboard component.

PP-DLW

PP-DLW Onboard LED

LED4

OFFPowered

Off

ONStandbyPower


2.4 Central Processing Unit (CPU)

2.4.1 OverviewThe motherboard comes with dual surface mount 604-pin Zero InsertionForce (ZIF) sockets. The sockets are designed for the Intel Processor inthe 603/604-pin package with 512KB L2 cache. The processor includesthe Intel® NetBurst™ micro-architecture that features Hyper-ThreadingTechnology, rapid execution engine, 533/400MHz system bus, andexecution trace cache. Together, these attributes improve systemperformance by allowing higher core frequencies, faster execution ofinteger instructions, and data transfer rate of up to 4.2GBps/3.2GBps.

Note in the illustration that the CPU has a gold triangular mark on onecorner. This mark indicates the processor Pin 1 that should match aspecific corner of the CPU socket.

Incorrect installation of the CPU into the socket may bend the pins andseverely damage the CPU!

The motherboard supports either one or two CPUs. If you are installingonly one CPU, you MUST install it in CPU socket 1.

CPU Socket 1(outer socket)

CPU Socket 2(inner socket)

PP-DLW

PP-DLW Socket 604

Xeon™ Processor

Gold Mark


Follow these steps to install a CPU.

1. Locate the 604-pin ZIF sockets onthe motherboard. Unlock thesocket by pressing the leversideways, then lift it up to at least115° angle.

2. Position the CPU above thesocket as shown.

3. Carefully insert the CPU into thesocket until it fits in place.

Make sure that the socketlever is lifted up to at least115° angle, otherwise the CPUdoes not fit in completely.

The CPU fits only in onecorrect orientation. DO NOTforce the CPU into the socketto prevent bending the pinsand damaging the CPU!

4. When the CPU is in place, pushdown the socket lever to securethe CPU. The lever clicks on theside tab to indicate that it islocked.

If you are installing two CPUs, it is more convenient to install in CPUsocket 2 first.

2.4.2 Installing the CPU

Marked Corner


The Intel® Xeon™ processors require specially designed heatsink and fanassembly to ensure optimum thermal condition and performance.

Follow these steps to install the CPU heatsink and fan.

2.4.3 Installing the CPU heatsink and fan

1. Place the heatsink and fanassembly on top of the installedCPU, making sure that it fits inplace.

2. Hook one end of the retentionbracket into the protruding tab onthe corner of the plastic retentionbase. (The retention base comesinstalled with the motherboard.)


3. Use a small flat screw driver toattach the other end of thebracket, while firmly holding downthe heatsink and fan assembly.The middle hook of the bracketsnaps in place if you properlyattached the two ends.

4. As shown, the middle hook of thebracket snaps in place if youproperly attached the two ends.

5. Do steps 2 to 4 to install the otherbracket.

6. When the heatsink and fanassembly is in place, connect thefan cable to the fan connector onthe motherboard labeled FAN2 (forthe CPU on socket 1) and FAN3(for the CPU on socket 2).

Don’t forget to connect theCPU fan cable. Hardwaremonitoring problems mayoccur if you fail to plug thecable.


2.5 System memory

2.5.1 OverviewThe motherboard comes with four Double Data Rate (DDR) Dual InlineMemory Module (DIMM) sockets. These sockets support up to 8GBsystem memory using 184-pin unbuffered/registered ECC/non-ECCPC2100/1600 DIMMs with Serial Presence Detect (SPD).

A DDR DIMM is keyed with a notch so that it fits in only one direction.DO NOT force a DIMM into a socket to avoid damaging the DIMM.

The DDR SDRAM technology evolved from the mainstream PC66, PC100,PC133 memory known as Single Data Rate (SDR) SDRAM. DDR memoryhowever, has the ability to perform two data operations in one clock cycle,thus providing twice the throughput of SDR memory. For example, a200MHz DDR DIMM will support a 100MHz memory bus, and a 266MHzDDR DIMM will support a 133MHz memory bus.

A DDR DIMM has the same physical dimensions as an SDR DIMM, but ithas a 184-pin footprint compared to the 168-pin of the SDR DIMM. Also, aDDR DIMM is single notched while an SDR DIMM is double notched.Therefore, a DDR DIMM is not backward compatible with SDR, and shouldbe installed only in a socket specially designed for DDR DIMMs.

DDR Data Transfer Rate DDR Base Frequency

266MHz 133MHz

200MHz 100MHz

PP-DLW

PP-DLW 184-Pin DDR DIMM Sockets80

Pin

s10

4 P

ins


2.5.2 Memory ConfigurationsYou may install 64MB, 128MB, 256MB, 512MB, 1GB, or 2GB Double DataRate (DDR) DIMMs into the four DIMM sockets using the memoryconfigurations presented in this section.

Important notes on memory configurations

1. Installing DDR DIMMs other than the recommended configurationsmay cause memory sizing error or system boot failure. See Table 1for the recommended configurations.

2. Install only identical (the same type and size) DDR DIMM pairsusing the recommended configurations.

3. Make sure that the memory frequency matches the CPU FSB(Front Side Bus). Refer to Table 2 below.

4. DO NOT mix unbuffered and registered DIMMs in anyconfiguration.

Table 1 Recommended memory configurations

Table 2 Memory frequency/CPU FSB synchronization

SocketsMode DDR1 DDR2 DDR3 DDR4

Single-channel (1) Module A — — —(2) — — Module A —

(3) Module A — Module A —

(4) Module A — Module B —

Dual-channel (1) Module A Module A — —(2) — — Module A Module A

(3) Module A Module A Module A Module A

(4) Module A Module A Module B Module B

CPU FSB DDR DIMM Type Memory Frequency

533 MHz PC2100 266 MHz

400 MHz PC1600 200 MHz


2.5.3 Installing a DIMM

Make sure to unplug the power supply before adding or removingDIMMs or other system components. Failure to do so may causesevere damage to both the motherboard and the components.

Follow these steps to install a DIMM.

1. Unlock a DIMM socket by pressingthe retaining clips outward.

2. Align a DIMM on the socket suchthat the notch on the DIMMmatches the break on the socket.

3. Firmly insert the DIMM into thesocket until the retaining clipssnap back in place and the DIMMis properly seated.

1. Simultaneously press the retainingclips outward to unlock the DIMM.

2. Remove the DIMM from thesocket.

Support the DIMM lightly withyour fingers when pressingthe retaining clips. The DIMMmight get damaged when itflips out with extra force.

Unlocked Retaining Clip

Locked Retaining Clip

2.5.4 Removing a DIMMFollow these steps to remove a DIMM.


2.6 Expansion slotsIn the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support.

2.6.1 Installing an expansion cardFollow these steps to install an expansion card.

1. Before installing the expansion card, read the documentation thatcame with it and make the necessary hardware settings for the card.

2. Remove the system unit cover (if your motherboard is already installedin a chassis).

3. Remove the bracket opposite the slot that you intend to use. Keep thescrew for later use.

4. Align the card connector with the slot and press firmly until the card iscompletely seated on the slot.

5. Secure the card to the chassis with the screw you removed earlier.

6. Replace the system cover.

Make sure to unplug the power cord before adding or removingexpansion cards. Failure to do so may cause you physical injury anddamage motherboard components.

2.6.2 Configuring an expansion cardAfter installing the expansion card, configure the it by adjusting thesoftware settings.

1. Turn on the system and change the necessary BIOS settings, if any.See Chapter 4 for information on BIOS setup.

2. Assign an IRQ to the card. Refer to the tables on the next page.

3. Install the software drivers for the expansion card.


Standard Interrupt AssignmentsIRQ Priority Standard Function 0 1 System Timer 1 2 Keyboard Controller 2 N/A Programmable Interrupt 3* 11 Communications Port (COM2) 4* 12 Communications Port (COM1) 5* 13 Sound Card (sometimes LPT2) 6 14 Floppy Disk Controller 7* 15 Printer Port (LPT1) 8 3 System CMOS/Real Time Clock 9* 4 ACPI Mode when used10* 5 IRQ Holder for PCI Steering11* 6 IRQ Holder for PCI Steering12* 7 PS/2 Compatible Mouse Port13 8 Numeric Data Processor14* 9 Primary IDE Channel15* 10 Secondary IDE Channel

* These IRQs are usually available for ISA or PCI devices.

IRQ assignments for this motherboard

PCI INTA PCI INTB PCI INTC PCI INTD

PCI-X slot 1 PBIRQ0 PBIRQ1 PBIRQ2 PBIRQ3



PCI-X slot 4 PAIRQ0 PAIRQ1 PAIRQ2 PAIRQ3

PCI slot 1 PIRQF PIRQG PIRQH PIRQE

AGP Pro slot PIRQA PIRQB — —

Onboard 82540EM controller PIRQD — — —

When using PCI cards on shared slots, ensure that the drivers support“Share IRQ” or that the cards do not need IRQ assignments.Otherwise, conflicts will arise between the two PCI groups, making thesystem unstable and the card inoperable.


2.6.3 PCI slotsThis motherboard implements the PCI-X (Peripheral Component InterconnectExtended) bus technology to support up to 133MHz data transfers, or about1.06GB/s. This bus technology is primarily designed for servers to increasethe performance of high bandwidth devices such as Ultra320 SCSI. PCI-X isbackward compatible with the earlier PCI bus technology making it possible toinstall PCI and PCI-X cards at the same time, but the bus speed will be that ofthe slowest card.

The following figure shows the four 64-bit PCI-X slots and the 32-bit PCI sloton the motherboard.

2.6.4 AGP Pro 8x slotThis motherboard has an Accelerated Graphics Port (AGP) Pro slot thatsupports AGP cards. Note the notches on the card golden fingers toensure that they fit the AGP slot on your motherboard.

The AGP PRO slot comes with a warning label and a safety tab.Remove the label and tab ONLY if you are installing an AGP PROcard. Use a pointed object, such as a pen tip, to dislodge the tab.

PP-DLW

PP-DLW Accelerated Graphics Port (AGP)

Keyed for 1.5V

PCI-X1 (66/100MHz, 3.3V)

PCI-X2 (66/100MHz, 3.3V)

PCI-X3 (66/100MHz, 3.3V)

PCI-X4 (133MHz, 3.3V)

PCI 1 (33MHz, 5V)


2.7 Jumpers

Keep the default settings for stable system operation.

1. JumperFree™ setting (J22)This jumper allows you to enable or disable the JumperFree™ mode.

2. CPU external frequency selection (J12)This jumper allows you to select your desired CPU external frequency(or bus clock).

PP-DLW

PP-DLW CPU External Frequency Selection

J12

CPU select(Default)

1 2

100MHz

2 3

133MHz

2 31

PP-DLW

PP-DLW JumperFree™ Mode Setting

J22

1 2 2 3

Jumper Free(Default)

Jumper Mode


3. Gigabit LAN setting (J14)

Set this jumper to pins 1-2 to enable the onboard Gigabit LANcontroller and support 10/100/1000BASE-T networking.

4. PCI-X slot setting (J15)This jumper allows you to select your desired bus speed for PCI-X1 toPCI-X3 slots.

PP-DLW

PP-DLW LAN Setting

J14

Enable(Default)

Disable

1 2 2 3

PP-DLW

PP-DLW PCI Slot Setting

12 2

3

J33

(Default)

PCI-X100MHz

PCI-X66MHz


5. Keyboard power (3-pin J1)

This jumper allows you to enable or disable the keyboard wake-upfeature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up thecomputer when you press a key on the keyboard. This feature requiresan ATX power supply that can supply at least 1A on the +5VSB lead,and a corresponding setting in the BIOS.

6. USB device wake-up (J28, J29, J20)Set these jumpers to +5V to wake up the computer from S1 sleepmode (CPU stopped, DRAM refreshed, system running in low powermode) using the connected USB devices. Set to +5VSB to wake upfrom S3 sleep mode (no power to CPU, DRAM in slow refresh, powersupply in reduced power mode).

The J28 and the J29 jumpers are for the rear USB ports. The J20 isfor the internal USB header that you can connect to the front USBports.

PP-DLW

PP-DLW Keyboard Power Setting

J1

(Default)+5V +5VSB

1 2 2 3

PP-DLW

PP-DLW USB Device Wake Up

12 2

3

J28J29

J20

(Default)+5V +5VSB

1 2 2 3

(Default)+5V +5VSB


7. Clear RTC RAM (J21)

This jumper allows you to clear the Real Time Clock (RTC) RAM inCMOS. You can clear the CMOS memory of date, time, and systemsetup parameters by erasing the CMOS RTC RAM data. The RAMdata in CMOS, that include system setup information such as systempasswords, is powered by the onboard button cell battery.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the

cap on pins 2-3 for about 5~10 seconds, then move the cap backto pins 1-2.

3. Plug the power cord and turn ON the computer.4. Hold down the key during the boot process and enter BIOS

setup to re-enter data.

Except when clearing the RTC RAM, never remove the cap on CLRTCjumper default position. Removing the cap will cause system bootfailure!

PP-DLW

PP-DLW Clear RTC RAM

J21

Normal(Default)

1 2

Clear CMOS

2 3


2.8 ConnectorsThis section describes and illustrates the internal connectors on themotherboard.

Always connect ribbon cables with the red stripe to Pin 1 on theconnectors. Pin 1 is usually on the side closest to the power connectoron hard drives and CD-ROM drives, but may be on the opposite sideon floppy disk drives.

2. Floppy disk drive connector (34-1 pin FLOPPY)This connector supports the provided floppy drive ribbon cable. Afterconnecting one end to the motherboard, connect the other end to thefloppy drive. (Pin 5 is removed to prevent incorrect insertion whenusing ribbon cables with pin 5 plug).

1. Hard disk activity LED (2-pin J24)This connector supplies power to the hard disk activity LED. The reador write activities of any device connected to the primary or secondaryIDE connector cause this LED to light up.

PP-DLW

PP-DLW IDE Activity LED

J24

TIP: If the case-mounted LED does notlight, try reversing the 2-pin plug.

-+

PP-DLW

NOTE: Orient the red markings onthe floppy ribbon cable to PIN 1.

PP-DLW Floppy Disk Drive Connector

PIN 1


3. IDE connectors (40-1 pin IDE1, IDE2)

This connector supports the provided UltraDMA/100/66 IDE hard diskribbon cable. Connect the cable’s blue connector to the primary(recommended) or secondary IDE connector, then connect the grayconnector to the UltraDMA/100/66 slave device (hard disk drive) andthe black connector to the UltraDMA/100/66 master device. It isrecommended that you connect non-UltraDMA/100/66 devices to thesecondary IDE connector. If you install two hard disks, you mustconfigure the second drive as a slave device by setting its jumperaccordingly. Refer to the hard disk documentation for the jumpersettings. BIOS supports specific device bootup. If you have more thantwo UltraDMA/100/66 devices, purchase another UltraDMA/100/66cable. You may configure two hard disks to be both master deviceswith two ribbon cables – one for the primary IDE connector andanother for the secondary IDE connector.

1. Pin 20 on each IDE connector is removed to match the coveredhole on the UltraDMA cable connector. This prevents incorrectorientation when you connect the cables.

2. The hole near the blue connector on the UltraDMA/100/66 cable isintentional.

For UltraDMA/100/66 IDE devices, use an 80-conductor IDE cable.The UltraDMA/66 cable included in the motherboard package alsosupports UltraDMA/100.

PP-DLW

PP-DLW IDE Connectors

NOTE: Orient the red markings(usually zigzag) on the IDEribbon cable to PIN 1.

Sec

onda

ry ID

E C

onne

ctor

Prim

ary

IDE

Con

nect

or

PIN 1

PIN 1


4. Chassis alarm lead (4-1 pin J23)

This lead is for a chassis designed with intrusion detection feature.This requires an external detection mechanism such as a chassisintrusion sensor or microswitch. When you remove any chassiscomponent, the sensor triggers and sends a high-level signal to thislead to record a chassis intrusion event.

By default, the pins labeled “Chassis Signal” and “Ground” are shortedwith a jumper cap. If you wish to use the chassis intrusion detectionfeature, remove the jumper cap from the pins.

5. SMBus connector (6-1 pin J16)

This connector allows you to connect SMBus (System ManagementBus) devices. Devices communicate with an SMBus host and/or otherSMBus devices using the SMBus interface. SMBus is a specificimplementation of an I2C bus, a multi-device bus that allows multiplechips to connect to the same bus and enable each one to act as amaster by initiating data transfer.

PP-DLW

PP-DLW Chassis Open Alarm Lead

J23

+5V

olt

(Pow

er S

uppl

y S

tand

By)

Cha

ssis

Sig

nal

Gro

und

PP-DLW

PP-DLW SMBus Connector

J16

1

SM

BC

LK

Gro

und

SM

BD

ATA

+5V

FLO

AT

ING


6. ATX power connectors (24/20-pin EATXPWR, 8-pin CON12V)

These connectors connect to an ATX 12V power supply. The plugsfrom the power supply are designed to fit these connectors in only oneorientation. Find the proper orientation and push down firmly until theconnectors completely fit.

In addition to the 24/20-pin EATXPWR connector, this motherboardrequires that you connect the 8-pin +12V power plug to the CON12Vconnector to provide sufficient power to the CPU.

Make sure that your ATX 12V power supply can provide 20A on the+12V lead and at least 1A on the +5-volt standby lead (+5VSB). Theminimum recommended wattage is 300W for a fully configured system.The system may become unstable and may experience difficultypowering up if the power supply is inadequate.

7. Front panel audio connector (10-1 pin J5)This is an interface for the Intel front panel audio cable that allowconvenient connection and control of audio devices.

PP-DLW

PP-DLW ATX Power Connector

For Power Supplywith 20-pin

Power Connector

24-pin Power Connector

GND 12VGND 12VGND 12VGND 12V

8-pin

+3 Volts+3 VoltsGround+5 Volts

+5 VoltsGround

GroundPower OK

+5V Standby+12 Volts

-5 Volts

+5 Volts

+3 Volts-12 VoltsGround

GroundGroundPSON#

Ground

+5 Volts

+12 Volts+3 Volts

+5 Volts

1

Ground

PP-DLW

PP-DLW Intel Panel Connector

J5

BOUT_L

MIC2

LOUT_R

LOUT_LNC

MICPWR+5VAAGND_A

1

BOUT_R


8. CPU, Chassis, and Power Fan Connectors(3-pin FAN1, FAN2, FAN3, FAN4, FAN5)

The fan connectors support cooling fans of 350mA~740mA (8.88Wmax.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fancables to the fan connectors on the motherboard, making sure that theblack wire of each cable matches the ground pin of the connector.

Do not forget to connect the fan cables to the fan connectors. Lack ofsufficient air flow within the system may damage the motherboardcomponents. These are not jumpers! DO NOT place jumper caps onthe fan connectors!

9. GAME/MIDI connector (16-1 pin GAME1)This connector supports a GAME/MIDI module. The GAME/MIDI porton the module connects a joystick or a game pad for playing games,and MIDI devices for playing or editing audio files.

PP-DLW

PP-DLW 12-Volt Cooling Fan Power

GND

Rotation+12V

FAN1

GND

Rotation+12V

GN

D

Rot

atio

n+

12V

GND

Rotation+12VFAN2

FAN3

FAN4

FAN5

GN

D

Rot

atio

n+

12V

The GAME/MIDI module is separately purchased.

PP-DLW

PP-DLW Game Connector

GAME11

+5V

J2B

1J2

CX

MID

I_O

UT

J2C

YJ2

B2

MID

I_IN

+5V

J1B

1J1

CX

GN

DG

ND

J1C

YJ1

B2

+5V

9

8

16


10. USB header (10-1 pin J25)

If the USB ports on the rear panel are inadequate, a USB header isavailable for additional USB ports. The USB header complies with USB2.0 specification that supports up to 480Mbps connection speed. Thisspeed advantage over the conventional 12Mbps on USB 1.1 allowsfaster Internet connection, interactive gaming, and simultaneousrunning of high-speed peripherals.

11. Infrared module connector (5-pin J26)This connector supports an optional wireless transmitting and receivinginfrared module. This module mounts to a small opening on systemchassis that support this feature. You must also configure the UART2Use As parameter in BIOS to set UART2 for use with IR.

Use the five pins as shown in Back View and connect a ribbon cablefrom the module to the motherboard SIR connector according to thepin definitions.

PP-DLW

PP-DLW USB 2.0 Header

US

B+

5VLD

M1

LDP

1G

ND

NC

US

B+

5VLD

M2

LDP

2G

ND

1 5

6 10J25

PP-DLW

PP-DLW Infrared Module Connector

Back View

+5VIRTX

IRRX(NC)GND

Front View

J26

+5V

IRR

X

IRT

X

GN

D

1

You may purchase a USB module to connect to the USB header.


13. Internal audio connectors (4-pin AUDIO_COM1, AUDIO_COM2)These connectors allow you to receive stereo audio input from soundsources such as a CD-ROM, TV tuner, or MPEG card. The MODEMconnector allows the onboard audio to interface with a voice modemcard with a similar connector. It also allows the sharing of mono_in(such as a phone) and a mono_out (such as a speaker) between theaudio and a voice modem card.

12. SMBus connector (6-1 pin J16)

This connector allows you to connect SMBus (System ManagementBus) devices. Devices communicate with an SMBus host and/or otherSMBus devices using the SMBus interface. SMBus is a specificimplementation of an I2C bus, a multi-device bus that allows multiplechips to connect to the same bus and enable each one to act as amaster by initiating data transfer.

PP-DLW

PP-DLW SMBus Connector

J16

1S

MB

CLK

Gro

und

SM

BD

ATA

+5V

FLO

AT

ING

PP-DLW

PP-DLW Internal Audio Connectors

AUDIO_COM1(Black)

AUDIO_COM2(White)

Right Audio Channel

Left Audio Channel

GroundGround


14. Wake-On-Ring Connector (2-pin J18)

This connector connects to internal modem cards with a Wake-On-Ring output. The connector wakes up the system when a ringup packetor signal is received through the internal modem card.

For external modems, Wake-On-Ring is detected through the COMport.

PP-DLW

PP-DLW Wake-On-Ring Connector

J18

Ring#Ground

21

15. System panel connector (20-pin PANEL)This connector accommodates several system front panel functions.

PP-DLW

PP-DLW System Panel Connectors* Requires an ATX power supply.

PLE

D

Gro

und

MLE

D

PW

R

+5V

SB

+5V Spe

aker

SpeakerConnectorPower LED

Gro

und

+5

V

Reset SW

SMI Lead

Message LED

Ext

SM

I#

Gro

und

Res

etG

roun

dG

roun

d

ATX PowerSwitch*

Gro

und

Key

lock

Keylock


• System Power LED Lead (3-1 pin PLED)

This 3-1 pin connector connects to the system power LED. The LEDlights up when you turn on the system power, and blinks when thesystem is in sleep mode.

• System Message LED Lead (2-pin MLED)This 2-pin connector is for the system message LED that indicatesreceipt of messages from a fax/modem. The normal status for this LEDis OFF, when there is no incoming data signal. The LED blinks whendata is received. The system message LED feature requires an ACPIOS and driver support.

• System Warning Speaker Lead (4-pin SPEAKER)

This 4-pin connector is for a chassis-mounted speaker.

• ATX Power Switch / Soft-Off Switch Lead (2-pin PWR)This lead connects a switch that controls the system power. Pressingthe power switch turns the system between ON and SLEEP, or ON andSOFT OFF, depending on the BIOS or OS settings. Pressing thepower switch while in the ON mode for more than 4 seconds turns thesystem OFF.

• Reset Switch Lead (2-pin RESET)

This lead connects to the case-mounted reset switch for rebooting thesystem without turning off the system power.

• System Management Interrupt Lead (2-pin SMI)This lead connects to the case-mounted suspend switch, and allowsyou to manually place the system into “Suspend Mode” or “GreenMode” where system activity is decreased to save electricity andexpand the life of system components.

• Keylock Lead (2-pin KEYLOCK)

This lead connects to a chassis-mounted switch to allow use of thekeyboard lock feature.

Chapter 3

Powering up

This chapter describes the power upsequence and gives information on theBIOS beep codes.


Chapter summary

3.1 Starting up for the first time.......................... 3-1

3.2 Powering off the computer ........................... 3-1


3.1 Starting up for the first time1. After making all the connections, replace the system case cover.

2. Be sure that all switches are off.

3. Connect the power cord to the power connector at the back of the systemchassis.

4. Connect the power cord to a power outlet that is equipped with a surgeprotector.

5. Turn on the devices in the following order:

a. Monitor

b. External SCSI devices (starting with the last device on the chain)

c. System power (if you are using an ATX power supply, you need toswitch on the power supply as well as press the ATX power switch onthe front of the chassis).

6. After applying power, the power LED on the system front panel case lightsup. For ATX power supplies, the system LED lights up when you press theATX power switch. If your monitor complies with “green” standards or if ithas a “power standby” feature, the monitor LED may light up or switchbetween orange and green after the system LED turns on. The systemthen runs the power-on tests. While the tests are running, the BIOS beepsor additional messages appear on the screen. If you do not see anythingwithin 30 seconds from the time you turned on the power, the system mayhave failed a power-on test. Check the jumper settings and connections orcall your retailer for assistance.

7. At power on, hold down to enter BIOS Setup. Follow theinstructions in Chapter 4.

3.2 Powering off the computerYou must first exit the operating system and shut down the system beforeswitching off the power. For ATX power supplies, you can press the ATXpower switch after exiting or shutting down the operating system. If youuse Windows 2000/XP, click the Start button, click Shut Down, then clickthe OK button to shut down the computer. The power supply should turnoff after Windows shuts down.

The message “You can now safely turn off your computer” does notappear when shutting down with ATX power supplies.

3-2 Chapter 3: Powering up

Chapter 4

BIOS setup

This chapter tells how to change systemsettings through the BIOS Setup menus.Detailed descriptions of the BIOSparameters are also provided.


Chapter summary

4.1 Managing and updating your BIOS .............. 4-1

4.2 BIOS Setup program...................................... 4-5

4.3 Main menu ...................................................... 4-8

4.4 Advanced menu ............................................. 4-9

4.5 PCI PnP menu .............................................. 4-19

4.6 Boot menu .................................................... 4-22

4.7 Security menu .............................................. 4-27

4.8 Chipset menu ............................................... 4-28

4.9 Power menu.................................................. 4-33

4.10 Exit menu ...................................................... 4-34


4.1 Managing and updating your BIOS

To update the BIOS, use the AFUDOS.EXE utility in DOS mode.

1. Copy the AFUDOS.EXE utility and the latest BIOS file into a floppydisk.

2. Insert the floppy disk into the drive, and type afudos at the prompt.The screen displays the command usage of the utility.

3. Type the command line afudos /filename.rom, where “filename.rom”means the original or latest BIOS file with which you wish to updatecurrent BIOS on the motherboard.

5. Boot the system with the new BIOS.

Visit the ASUS website (www.asus.com) to obtain BIOS updates forthis motherboard.

4. Press Enter. The screen displays the status of the update and goesback to the DOS prompt when done.

4-2 Chapter 4: BIOS Setup

4.2 BIOS Setup programThis motherboard supports a programmable firmware hub (FWH) that youcan update using the provided utility described in section “4.1 Managingand updating your BIOS.”

Use the BIOS Setup program when you are installing a motherboard,reconfiguring your system, or prompted to “Run Setup”. This sectionexplains how to configure your system using this utility.

Even if you are not prompted to use the Setup program, you may want tochange the configuration of your computer in the future. For example, youmay want to enable the security password feature or make changes to thepower management settings. This requires you to reconfigure your systemusing the BIOS Setup program so that the computer can recognize thesechanges and record them in the CMOS RAM of the firmware hub.

The firmware hub on the motherboard stores the Setup utility. When youstart up the computer, the system provides you with the opportunity to runthis program. Press during the Power-On Self Test (POST) toenter the Setup utility, otherwise, POST continues with its test routines.

If you wish to enter Setup after POST, restart the system by pressing + + , or by pressing the reset button on the systemchassis. You can also restart by turning the system off and then back on.Do this last option only if the first two failed.

The Setup program is designed to make it as easy to use as possible. It isa menu-driven program, which means you can scroll through the varioussub-menus and make your selections among the predetermined choices.

Because the BIOS software is constantly being updated, the followingBIOS setup screens and descriptions are for reference purposes only,and may not exactly match what you see on your screen.


4.2.2 Menu barThe menu bar on top of the screen has the following main items:

Main For changing the basic system configuration

Advanced For changing the advanced system settingsPCIPnP For changing the PCI/PnP settingsBoot For changing the system boot configurationSecurity For changing the system security settings

Chipset For changing the advanced chipset settingsPower For changing the APM configurationExit For selecting the exit options and loading default settings

To select the menu bar items, press the right or left arrow key on thekeyboard until the desired item is highlighted.

4.2.1 BIOS menu screen

Navigation keys

General helpMenu bar

Menu items Field setting


4.2.4 General helpAt the top right corner of the menu screen is a brief description of theselected item.

4.2.5 Sub-menuAn item with a sub-menu on any menuscreen is distinguished by a solid trianglebefore the item. To display the sub-menu,select the item and press Enter.

Some of the navigation keys differ from one screen to another.

4.2.6 Scroll barA scroll bar appears on the right side ofa menu screen when there are itemsthat do not fit on the screen. Press Up/Down arrow keys or PageUp/PageDown keys to display the otheritems on the screen.

4.2.3 Navigation keysAt the bottom right corner of a menu screen are the navigation keys forthat particular menu. Use the navigation keys to select items in the menuand change the settings.

4.2.7 Pop-up windowSelect an item in the menu, then pressEnter to display a pop-up window withthe configuration options for that item.

Scroll bar

Pop-up window


4.3 Main menuWhen you enter the BIOS Setup program, the Main menu screen appearsgiving you an overview of the basic system information.

4.3.1 AMI BIOSThis item displays the auto-detected BIOS information.

4.3.2 ProcessorThis item displays the auto-detected CPU specification.

4.3.3 System MemoryThis item displays the auto-detected system memory installed.

4.3.4 System Time [xx:xx:xxxx]This item allows you to set the system time.

4.3.5 System Date [Day xx/xx/xxxx]This item allows you to set the system date.

Refer to section “4.2.1 BIOS menu screen” for information on themenu screen items and how to navigate through them.


4.4 Advanced menuThe Advanced menu items allow you to change the settings for the CPUand other system devices.

Take caution when changing the settings of the Advanced menu items.Incorrect field values may cause the system to malfunction.

4.4.1 CPU ConfigurationThe items in this menu allow you to change CPU-related settings. Selectthe item then press Enter to display the sub-menu.


The values opposite the dimmed items Manufacturer, Brand String,Frequency, Ratio Status, and Ratio Actual Value are auto-detected byBIOS and are not user-configurable.

Ratio CMOS Setting [8]Sets the ratio between the CPU core clock and the FSB frequency. If aninvalid ratio is set in CMOS, the actual and set point values may differ.This item is auto-detected.

Hyper-Threading [Disabled]This item allows you to enable or disable the CPU Hyper-ThreadingTechnology feature. Configuration options: [Disabled] [Enabled]

4.4.2 IDE ConfigurationThe items in this menu allow you to change the settings for the IDE drivesinstalled in the system. Select an item then press Enter to display theconfiguration options. For other items, a sub-menu appears when youpress Enter.

Onboard PCI IDE Controller [Both]This item allows you to enable or disable the IDE controller. Configurationoptions: [Disabled] [Primary] [Secondary] [Both]

The IDE master/slave items show Not Detected if no IDE device isinstalled in the system.


Primary IDE MasterPrimary IDE SlaveSecondary IDE MasterSecondary IDE SlaveWhile entering Setup, BIOS auto-detects the presence of IDE devices.These fields display the information of the detected IDE devices.

These items have sub-menus. Select an item then press Enter to displaythe specific sub-menu.

The values opposite the dimmed items Device, Vendor, Size, LBA Mode,Block Mode, PIO Mode, Async DMA, Ultra DMA, and S.M.A.R.T. are auto-detected by BIOS and are not user-configurable.These items show N/A ifno IDE device is installed in the system.

Type [Auto]

Selects the type of IDE drive. Configuration options: [Not Installed][Auto] [CDROM] [ARMD]

LBA/Large Mode [Auto]

Enables or disables the LBA mode. Setting to Auto enables the LBAmode if the device supports this mode, and if the device was notpreviously formatted with LBA mode disabled. Configuration options:[Disabled] [Auto]

Block (Multi-sector Transfer) [Auto]

Enables or disables data multi-sectors transfers. When set to Auto, thedata transfer from and to the device occurs multiple sectors at a time ifthe device supports multi-sector transfer feature. When set toDisabled, the data transfer from and to the device occurs one sector ata time. Configuration options: [Disabled] [Auto]


PIO Mode [Auto]

Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4]

DMA Mode [Auto]

Selects the DMA mode. Configuration options: [Auto] [SWDMA0][SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0][UDMA1] [UDMA2] [UDMA3] [UDMA4]

S.M.A.R.T. [Auto]

Sets the Smart Monitoring, Analysis, and Reporting Technology.Configuration options: [Auto] [Disabled] [Enabled]

32Bit Data Transfer [Disabled]

Enables or disables 32-bit data transfer. Configuration options:[Disabled] [Enabled]

Hard Disk Write Protect [Disabled]Enables or disables device write protection. This will be effective only if thedevice is accessed through BIOS. Configuration options: [Disabled][Enabled]

IDE Detect Time Out (Sec) [35]Selects the time out value for detecting ATA/ATAPI devices. Configurationoptions: [0] [5] [10] [15] [20] [25] [30] [35]

ATA(PI) 80Pin Cable Detection [Host & Device]Selects the mechanism for detecting 80-pin ATA/ATAPI cable.Configuration options: [Host & Device] [Host] [Device]


4.4.3 Floppy ConfigurationThe items in this menu allow you to change the settings for the floppydrives installed in the system. Select an item then press Enter to displaythe configuration options.

Floppy A [Disabled]Floppy B [Disabled]Selects the type of floppy drive installed in the system. Configurationoptions: [Disabled] [360 KB 5 1/4] [1.2 MB 5 1/4] [720 KB 3 1/2] [1.44 MB3 1/2] [2.88 MB 3 1/2]

4.4.4 Super IO ConfigurationThe items in this menu allow you to configure the Super I/O chipset. Selectan item then press Enter to display the configuration options.


OnBoard Floppy Controller [Enabled]Allows you to enable or disable the floppy disk controller. Configurationoptions: [Disabled] [ Enabled]

Serial Port1 Address [3F8/IRQ4]Allows you to select the Serial Port1 base address. Configuration options:[Disabled] [3F8/IRQ4] [3E8/IRQ4] [2E8/IRQ3]

Serial Port2 Address [2F8/IRQ3]Allows you to select the Serial Port2 base address. Configuration options:[Disabled] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3]

Serial Port2 Mode [Normal]

Allows you to select the mode for Serial Port2. When the item SerialPort 2 Address is set to Disabled, this item does not appear.Configuration options: [Normal] [Sharp-IR] [SIR] [Consumer]

IR Duplex Mode

Allows selection of either Full Duplex or Half Duplex for Serial Port2 inIR mode. This item appears only when Serial Port2 Mode is set toeither Sharp-IR, SIR, or Consumer.

IR Receiver Pin

Allows selection of either Receiver pin or Transmit pin for Serial Port2in IR mode. This item appears only when Serial Port2 Mode is set toeither Sharp-IR, SIR, or Consumer.

Parallel Port Address [378]Allows you to select the Parallel Port base addresses. Configurationoptions: [Disabled] [378] [278] [3BC]

Parallel Port Mode [Normal]

Allows you to select the Parallel Port mode. When the item ParallelPort Address is set to 278, the Parallel Port Mode options are onlyNormal and EPP. Configuration options: [Normal] [Bi-directional] [EPP][ECP]

EPP Version [1.9]

Allows selection of the Parallel Port EPP version. This item appearsonly when the Parallel Port Mode is set to EPP. Configuration options:[1.9] [1.7]


4.4.5 ACPI ConfigurationThe items in this menu allow you to change the ACPI (AdvancedConfiguration and Power Interface) settings. Select an item then pressEnter to display the configuration options. For other items, a sub-menuappears when you press Enter.

ACPI Aware O/S [Yes]Allows you to enable or disable ACPI support for your operating system.Select No if your operating system does not support ACPI. Select Yes ifyour operating system supports ACPI. Configuration options: [No] [Yes]

ECP Mode DMA Channel [DMA3]

Allows selection of the Parallel Port ECP DMA. This item appears onlywhen the Parallel Port Mode is set to ECP. Configuration options:[DMA0] [DMA1] [DMA3]

Parallel Port IRQ [IRQ7]

Allows you to select the Parallel Port IRQ. Configuration options:[IRQ5] [IRQ7]

Onboard Game Port [Disabled]Allows you to select the Game Port address or to disable the port.Configuration options: [Disabled] [220h-22Fh] [210h-21Fh]

Onboard MIDI Port [Disabled]Allows you to select the MIDI Port address or to disable the port.Configuration options: [Disabled] [300] [330]


General ACPI ConfigurationAllows you change the general ACPI settings.

Advanced ACPI ConfigurationAllows you to change the advanced ACPI settings.

Suspend Mode [S1 (POS) Only]

Allows you to select the ACPI state to be used for system suspend.Configuration options: [S1 (POS) Only] [S1 & S3 (STR)]

Repost Video On S3 Resume [Yes]

Determines whether to invoke VGA BIOS post on S3/STR resume.Configuration options: [Yes] [No]

BIOS -> AML ACPI Table [Enabled]

Allows you to enable or disable the inclusion of the BIOS -> AMLexchange pointer to (X)RSDT pointer list. Configuration options:[Disabled] [Enabled]


4.4.6 USB ConfigurationThe items in this menu allows you to change the USB-related features.Select an item then press Enter to display the configuration options.

Legacy USB Support [Enabled]Allows you to enable or disable support for legacy USB devices. Setting toAuto disables the legacy support if no USB devices are connected.Configuration options: [Disabled] [Enabled] [Auto]

USB 2.0 Controller Mode [HiSpeed]Allows you to configure the USB 2.0 controller in HiSpeed (480 Mbps) orFull Speed (12 Mbps). Configuration options: [HiSpeed ] [Full Speed]

The Module Version and USB Devices Enabled items show the auto-detected values. If no USB device is detected, the item shows None.


4.4.7 System Health Configuration

USB Mass Storage Reset Delay [20 Sec]

Allows you to select the number of seconds POST waits for the USBmass storage device after the start unit command. The message “NoUSB mass storage device detected” appears if none is installed in thesystem. Configuration options: [10 Sec ] [20 Sec] [30 Sec] [40 Sec]

USB Mass Storage Device Configuration

System Health Configuration [Enabled]Allows you to enable or disable the System Health Configuration feature.When this feature is enabled, the items in the menu displays the auto-detected fan speeds, system temperatures, and output voltages. Whendisabled, the items show [N/A]. Configuration options: [Disabled] [Enabled]


4.5 PCI PnP menuThe PCI PnP menu items allow you to change the advanced settings forPCI/PnP devices. The menu includes setting IRQ and DMA channelresources for either PCI/PnP or legacy ISA devices, and enabling ordisabling the PCI device option ROM for shadow memory.

4.5.1 Plug & Play O/S [No]When set to [No], BIOS configures all the devices in the system. When setto [Yes] and if you installed a Plug & Play operating system, the operatingsystem configures the Plug & Play devices not required for boot.Configuration options: [No] [Yes]

4.5.2 PCI Latency Timer [64]This item allows you to select the value in units of PCI clocks for the PCIdevice latency timer register. Configuration options: [32] [64] [96] [128][160] [192] [224] [248]

4.5.3 Pallete Snooping [Enabled]When set to [Enabled], the pallete snooping feature informs the PCIdevices that an ISA graphics device is installed in the system so that thelatter can function correctly. Setting to [Disabled] deactivates this feature.configuration options: [Disabled] [Enabled]

Take caution when changing the settings of the PCI PnP menu items.Incorrect field values may cause the system to malfunction.


4.5.4 Slot 1, Slot 2, Slot 3, Slot 4, Slot 5 OptionROM Keep [Enabled]

These items allow you to enable or disable copying the PCI device optionROM to shadow memory. Configuration options: [Disabled] [Enabled]

4.5.5 Onboard LAN Option ROM Keep [Enabled]This item allows you to enable or disable copying the onboard LAN optionROM to shadow memory. Configuration options: [Disabled] [Enabled]


4.6 Boot menuThe Boot menu items allow you to change the system boot options. Selectan item then press Enter to display the sub-menu.

4.6.1 Boot Settings Configuration

Quick Boot [Enabled]Enabling this item allows BIOS to skip some power on self tests (POST)while booting to decrease the time needed to boot the system. When setto [Disabled], BIOS performs all the POST items. Configuration options:[Disabled] [Enabled]

Quiet Boot [Disabled]Setting to [Disabled] displays the normal POST messages. Setting to[Enabled] displays the OEM logo instead of the POSt messages.Configuration options: [Disabled] [Enabled]


Bootup Num-Lock [On]Allows you to select the power-on state for the NumLock. Configurationoptions: [Off] [On]

PS/2 Mouse Support [Enabled]Allows you to enable or disable support fr PS/2 mouse. Configurationoptions: [Disabled] [enabled]

Typematic Rate [Fast]Allows you to select the keyboard typematic rate. Configuration options:[Slow] [Fast]

System Keyboard [Present]Allows you to enable or disable the keyboard/s connected to the system[Absent] [Present]

Boot to OS/2 [No]Allows you to specify the OS/2 compatibility mode. Configuration options:[No] [Yes]

Wait for ‘F1’ If Error [Enabled]When set to Enabled, the system waits for F1 key to be pressed whenerror occurs. Configuration options: [Disabled] [Enabled]

Hit ‘DEL’ Message Display [Enabled]When set to Enabled, the system displays the message “Press DEL to runSetup” during POST. Configuration options: [Disabled] [Enabled]

Interrupt 19 Capture [Disabled]When set to [Enabled], this function allows the option ROMs to trapInterrupt 19. Configuration options: [Disabled] [Enabled]


4.6.2 Boot Device Priority

4.6.3 Hard Disk Drives

1st ~ 12th Boot Device [1st Floppy Drive]These items specify the boot device priority sequence from the availabledevices. The number of device items that appear on the screen dependson the the number of devices installed in the system. Configurationoptions: [xxxxx Drive] [Disabled]

1st ~ 12th DriveThese items specify the boot priority sequence from the available harddisk drives. The number of device items that appear on the screendepends on the the number of devices installed in the system.Configuration options: [xxxxx Drive] [Disabled]


4.6.4 Removable Drives

4.6.5 ATAPI CDROM Drives

1st ~ 4th DriveThese items specify the boot priority sequence from the availableremovable drives. The number of device items that appear on the screendepends on the the number of devices installed in the system.Configuration options: [xxxxx Drive] [Disabled]

1st ~ 4th DriveThese items specify the boot priority sequence from the available ATAPICD- ROM drives. The number of device items that appear on the screendepends on the the number of devices installed in the system.Configuration options: [xxxxx Drive] [Disabled]


4.7 Security menuThe Security menu items allow you to change the system security settings.Select an item then press Enter to display the configuration options.

4.7.1 Change Supervisor PasswordSelect this item to set or change the supervisor password. The SupervisorPassword item on top of the screen shows the default Not Installed. Afteryou have set a password, this item shows Installed.

To set a Supervisor Password:

1. Select the Change Supervisor Password item and press Enter.

2. On the password box that appears, type a password composed ofletters and/or numbers, then press Enter. Your password should haveat least six characters.

3. Confirm the password when prompted.The message “Password Installed” appears after you havesuccessfully set your password.

The Supervisor Password item now shows Installed.

To change the supervisor password, follow the same steps as in setting auser password.

To clear the supervisor password, select the Change Supervisor Passwordthen press Enter. The message “Password Uninstalled” appears.


4.7.2 User Access Level (Full Access]After you have set a supervisor password, the item User Access Levelappears. This item allows you to select the access restriction to the Setupitems. Configuration options: [No Access] [View Only] [Limited] [FullAccess]

No Access prevents user access to the Setup utility.

View Only allows access but does not allow change to any

Documents

PP-DLW - Asusdlcdnet.asus.com/pub/ASUS/mb/Socket604/pp-dlw/e1173_pp-dlw.pdfiii Features Contents Notices .....vi Safety information ..... vii