Spare parts manual SAB 87 - Sabroe

Spare parts manual SAB 87

Screw compressor unit

ENG

18. Parts list for SAB 87

1/50662-831 - ENRev. 2006.09

Spare parts Manual SAB 87 - HP compressor

0662

_831

_EN

G.fm

18. Parts list for SAB 87HP compressor

Relevant drawing document: 0662-830

Pos. no. Designation No. Part no.2 Rotor housing, unclassified 1 3011-030

2 Rotor housing, sph. cast iron 1 3011-049 11)

4 Bearing housing unclassified 1 3013-240

4 Bearing housing, sph. cast iron 1 3013-362 11)

5 Dowel pin 2 2122-027

7 Pair of rotors, unclassified 1 3024-129

8 Gasket 1 2353-191

10 Distance washer 1 3049-050

11 Radial bearing 2320 1 1513-053

12 Radial bearing 2319 1 1511-028

13 Radial bearing 2316 2 1513-055

14 Thrust bearing 7318 3 1512-012

15 Thrust bearing 7317 2 1512-011

16 Nut M85x2 2 1514-021

18 Shaft seal 1 1332-187

18 Shaft seal, Double Ply Bellows 1 1332-191 11)

19 Snap Ring 1 3026-045

20 Spacer sleeve 1 3049-048


23 Bearing cover 1 3013-241

24 Gasket 1 2353-192

25 Seat holder 1 3026-042

26 Oil collector 1 3026-043

27 Gasket 1 2353-193

29 Pipe no. 1904 207-1 Replaced by : hose connecting branch 1/4”

1 1345-143

30 Draining hose no. 1904 211- 3

32 Adjusting screw 3 3049-051

33 Protecting washer 1 3049-052

34 Shims 1 2212-139

36 Balancing piston 1 3025-044 1)

37 Orifice plug ø1 1 3049-067 2)

38 Cover 1 3013-242

39 Slide valve 1 3049-158 4)

40 Slide valve, eco 1 3043-271 3)

41 Guide block 1 3049-053

42 Retainer for transmitter, complete 1 3045-074

44a Stop Screw (part of pos. 42) (4) 1413-231

45 Cover-Bearing housing 1 3013-244

46 Dowel pin 1 3049-055

47 Cylinder 1 3043-185

48 Cylinder head 1 3013-245

49 Hydraulic piston 1 3043-186

50 Piston rod 1 3043-188


2/5 0662-831 - ENRev. 2006.09


51 Probe 1 3045-068

52 Spring housing 1 3049-056

53 Gland 1 3043-192

54 Washer 1 3043-193

55 Unloading spring 1 3043-194

56 Support ring 1 2353-199

57 Vi-piston 1 3044-075 6)

58 Vi-cylinder 1 3044-076 5)

59 Cover, Vi-cylinder 1 3013-249 5)

60 Gasket 1 2353-194

61 Hydraulic piston 1 3044-077 5)

62 Piston rod 1 3044-078 5)

63 Indicator 1 3044-079 5)

64 Dowel pin 1 3044-080 6)

66 Support ring 1 2353-200 5)

67 Pilot valve 1 1372-208 5)

68 Cover 1 3013-250 5)

69 Gasket 1 2353-195

70 Control piston 1 3044-081 5)

71 Spring 1 3044-083 5)

72 Blind cover 1 3013-257 7)

75 Suction filter 1 3042-115

76 Gasket 2 2353-196

77 Filter holder 1 3042-116

78 Suction filter cover 1 3013-251

79 Guide 1 3042-117

81 Blind cover 1 3013-258 7)

82 Distance ring 1 2124-096 8)

84 Cover 1 3013-252

85 Cover 1 3013-253

86 Cover 1 3013-254

87 Cover 1 3013-255

88 Gasket 1 2353-197

89 Orifice plug ø8,0 2 3044-082

95 Oil pump 1 1524-221

96 Gasket 1 2353-198

97 Oil pump holder 1 3041-013

99 Reducing piston 1 3041-014

108 Blanking Plug with nut 3 1349-184

109 Stop valve 2 1361-119

110 Stop valve 1 1361-117

111 Connector 1 1349-137

112 Compressor name plate 1 2516-327

114 Warning sign 1 2516-302

115 Sign with logo 1 2516-303

116 Screw nail 8 1414-200

120 Blind flange DN 25 1 1344-302

Pos. no. Designation No. Part no.


3/50662-831 - ENRev. 2006.09


0662

_831

_EN

G.fm

123 Blind flange DN 65 1 1344-303

124 Gasket 43/57x2 1 2356-065

127 Gasket 95/109x2 1 2356-222

128 Spiral pin 3x10 2 1446-037

130 Spiral pin 6x16 2 1446-038

131 Parallel pin CPK 10x35 2 1445-082

132 Parallel pin 10x30 9(7) 1445-081 9)

134 Parallel pin 10x120 1 1445-085 5)

135 Parallel pin 10x140 1 1445-086 5)

138 Tension pin 6x32 1 1446-039

139 Grooved pin 4x14 1 1446-041

141 Retaining ring SgH 40 1 1437-150 5)

142 Retaining ring SgH 70 1 1437-159


145 Retaining ring SgA 80 1(2) 1437-230 2.1)

146 Retaining ring SgA 100 1 1437-244

148 Disc spring 4 1523-054 8)

149 Disc spring 2 1523-039

150 Disc spring 8 1523-048

151 Disc spring 1 1523-052

152 Pressure spring 1 1523-053


154 Gasket 10/16 11(10) 1331-426 9)

155 Plug 1/16” 9(2) 1343-021 9)

156 Plug G1/8 11(10) 1343-024 9)

158 Plug G3/8 16 1343-026

160 Plug G1/4 2 1343-025

161 Plug G1/2 6 1343-027

162 Plug G3/4 9 1343-028

163 Plug G1 3 1343-030

164 Gasket 17/24 16 1331-427

165 Gasket 14/21 2 1331-428

166 Gasket 22/29 6 1331-430

167 Gasket 27/35 9 1331-433

168 Gasket 34/43 3 1331-437

169 Gasket 34/43 1 1331-437

170 Slide ring 1 1243-020 5)

171 Slide ring 1 1243-021

173 Sealing ring 1 1332-034

174 Sealing ring 1 1332-037 5)


176 Sealing ring 1 1332-041 5)


180 Sight glass 1 1226-029

181 Check valve 1 1364-200

182 Check valve 1 1364-197

184 V-ring 1 1332-036



4/5 0662-831 - ENRev. 2006.09


187 O-ring 10,3x2,4 1 1331-612

188 O-ring 15,3x2,4 3 1331-613

191 O-ring 19,2x3 1 1331-614

192 O-ring 24,2x3 1 1331-615 5)

193 O-ring 29,2x3 1 1331-486 5)

194 O-ring 39,2x3 1 1331-616 5)

195 O-ring 44,2x3 2 1331-617

196 O-ring 49,5x3 2(1) 1331-618 9)

197 O-ring 54,5x3 1 1331-619

199 O-ring 69,5x3 1 1331-620

200 O-ring 79,5x3 1 1331-621

203 O-ring 109,5x3 2(1) 1331-487 9)

204 O-ring 114,5x3 1 1331-622

205 O-ring 124,5x3 1 1331-488 5)

206 O-ring 129,5x3 1 1331-624

207 O-ring 49,2x5,7 2(1) 1331-629 9)

208 O-ring 149,3x5,7 1 1331-489

209 O-ring 159,3x5,7 2 1331-630

210 O-ring 184,3x5,7 2 1331-634

211 O-ring 279,3x5,7 1 1331-638

212 O-ring 119,5x3,0 1 1331-623

214 Hexagon screw M12x35 4 1424-216

216 Hex socket screw 16x45 32 1413-433

219 Lifting eye M30 2 1427-160

223 Grub screw 6x10 2 1413-231

228 Hex. socket screw 5x30 4 1413-035




233 Hex. socket screw 10x30 9(7) 1413-372 9)

234 Hex. Socket screw 10x35 23 1413-373




239 Hex. Socket screw 10x110 3 1413-393 5)






256 Plug 3/8” 2 1343-023

259 Connection Angle 2 1349-233

270 Protecting cover 1 1246-059

275 Solenoid valve with coils 220-240 V AC 1 1372-584 10)

Solenoid valve with coils 110-120 V AC 1 1372-585 10)

Solenoid valve with coils 24 V AC 1 1372-586 10)

Solenoid valve with coils 24 V DC 1 1372-583 10)



5/50662-831 - ENRev. 2006.09


0662

_831

_EN

G.fm

1) Only for high pressure compressor

2) Only for booster compressors

2.1) No. in ( ) for booster compressor

3) Compressors with economizer

4) Compressors without economizer

5) Only for compressors with variable Vi

6) Only for compressors with variable Vi or fixed Vi = 4.8

7) Only for compressors with fixed Vi = 2.6 or 4.8

8) Only for compressors with fixed Vi = 4.8

9) No. In ( ) for compressors with fixed Vi

9.1) No. In ( ) for compressors with fixed Vi=2,6

10) Depending on pilot voltage

11) For max. operating pressure 33,5 bar (R410A)

Coil 220-240 V AC 2 1921 470-1 10)

Coil 110-120 V AC 2 1921 470-2 10)

Coil 24 V AC 2 1921 470-3 10)

276 Orifice plug 2.0 1 1371-172

277 Orifice plug 2.5 1 1371-173

280 Position transmitter 1 1553-276

281 Bushing for capacity transmitter 1 3043-251

282 Alu pipe for retainer (part of pos. 42) (1) 1116-018

283 Hexagon socketscrew M6x35 2 1413-344

285 Hexagon Screw M27x70 12 1424-342



1/50662-837 - ENRev. 2006.06

Spare parts Manual SAB 87 - Booster compressor

0662

_837

_EN

G.fm

18. Parts list for SAB 87Booster compressor

Relevant drawing document: 0662-830 1, 3 - 4 - 5 - 6/6 and 4848 - R - 305E 8/12

Pos. no. Designation No. Part no.2 Rotor housing, unclassified 1 3011-030

4 Bearing housing unclassified 1 3013-256

5 Dowel pin 2 2122-027

7 Pair of rotors, unclassified 1 3024-132

8 Gasket 1 2353-191

9 Holder 1 3049-063

10 Distance washer 1 3049-064

11 Discharge sleeve 1 3049-065

12 Discharge sleeve 1 3049-066

13 Bearing 6316 2 1511-009

14 Thrust bearing 7318 4 1512-012

16 Nut M85x2 2 1514-021

18 Shaft seal 1 1332-187

19 Snap Ring 1 3026-045


23 Bearing cover 1 3013-241

24 Gasket 1 2353-192

25 Seat holder 1 3026-042

26 Oil collector 1 3026-043

27 Gasket 1 2353-193

29 Pipe no. 1904 207-1 Replaced by : hose connecting branch 1/4”

1 1345-143

30 Draining hose no. 1904 211- 3

32 Adjusting screw 3 3049-051

33 Protecting washer 1 3049-052

34 Shims 1 2212-139

37 Orifice plug ø1 1 3049-067

38 Cover 1 3013-242

39 Slide valve 1 3049-158 4)

40 Slide valve, eco 1 3043-271 3)

41 Guide block 1 3049-053

42 Retainer for transmitter, complete 1 3045-074

44a Stop Screw (part of pos. 42) (4) 1413-231

45 Cover-Bearing housing 1 3013-244

46 Dowel pin 1 3049-055

47 Cylinder 1 3043-185

48 Cylinder head 1 3013-245

49 Hydraulic piston 1 3043-186

50 Piston rod 1 3043-188

51 Probe 1 3045-068

52 Spring housing 1 3049-056

53 Gland 1 3043-192


2/5 0662-837 - ENRev. 2006.06


54 Washer 1 3043-193

55 Unloading spring 1 3043-194

56 Support ring 1 2353-199

57 Vi-piston 1 3044-075 6)

58 Vi-cylinder 1 3044-076 5)

59 Cover, Vi-cylinder 1 3013-249 5)

60 Gasket 1 2353-194

61 Hydraulic piston 1 3044-077 5)

62 Piston rod 1 3044-078 5)

63 Indicator 1 3044-079 5)

64 Dowel pin 1 3044-080 6)

66 Support ring 1 2353-200 5)

67 Pilot valve 1 1372-208 5)

68 Cover 1 3013-250 5)

69 Gasket 1 2353-195

70 Control piston 1 3044-081 5)

71 Spring 1 3044-083 5)

72 Blind cover 1 3013-257 7)

75 Suction filter 1 3042-115

76 Gasket 2 2353-196

77 Filter holder 1 3042-116

78 Suction filter cover 1 3013-251

79 Guide 1 3042-117

81 Blind cover 1 3013-258 7)

82 Distance ring 1 2124-096 8)

84 Cover 1 3013-252

85 Cover 1 3013-253

86 Cover 1 3013-254

87 Cover 1 3013-255

88 Gasket 1 2353-197

89 Orifice plug ø8,0 2 3044-082

95 Oil pump 1 1524-221

96 Gasket 1 2353-198

97 Oil pump holder 1 3041-013

99 Reducing piston 1 3041-014

108 Blanking Plug with nut 3 1349-184

109 Stop valve 2 1361-119

110 Stop valve 1 1361-117

111 Connector 1 1349-137

112 Compressor name plate 1 2516-327

114 Warning sign 1 2516-302

115 Sign with logo 1 2516-303

116 Screw nail 8 1414-200

120 Blind flange DN 25 1 1344-302

123 Blind flange DN 65 2 1344-303

124 Gasket 43/57x2 1 2356-065

127 Gasket 95/109x2 2 2356-222



3/50662-837 - ENRev. 2006.06


0662

_837

_EN

G.fm

128 Spiral pin 3x10 2 1446-037

130 Spiral pin 6x16 2 1446-038

131 Parallel pin CPK 10x35 2 1445-082

132 Parallel pin 10x30 9(7) 1445-081 9)

134 Parallel pin 10x120 1 1445-085 5)

135 Parallel pin 10x140 1 1445-086 5)

138 Tension pin 6x32 1 1446-039

139 Grooved pin 4x14 1 1446-041

141 Retaining ring SgH 40 1 1437-150 5)



145 Retaining ring SgA 80 2 1437-230

148 Disc spring 4 1523-054 8)

149 Disc spring 2 1523-039

150 Disc spring 8 1523-048

151 Disc spring 1 1523-052



154 Gasket 10/16 11(10) 1331-426 9)

155 Plug 1/16” 9(2) 1343-021 9)

156 Plug G1/8 11(10) 1343-024 9)

158 Plug G3/8 16 1343-026

160 Plug G1/4 2 1343-025

161 Plug G1/2 6 1343-027

162 Plug G3/4 9 1343-028

163 Plug G1 3 1343-030

164 Gasket 17/24 16 1331-427

165 Gasket 14/21 2 1331-428

166 Gasket 22/29 6 1331-430

167 Gasket 27/35 9 1331-433

168 Gasket 34/43 3 1331-437

169 Gasket 34/43 1 1331-437

170 Slide ring 1 1243-020 5)

171 Slide ring 1 1243-021


174 Sealing ring 1 1332-037 5)


176 Sealing ring 1 1332-041 5)


180 Sight glass 1 1226-029

181 Check valve 1 1364-200

182 Check valve 1 1364-197

184 V-ring 1 1332-036

187 O-ring 10,3x2,4 1 1331-612

188 O-ring 15,3x2,4 3 1331-613

191 O-ring 19,2x3 1 1331-614

192 O-ring 24,2x3 1 1331-615 5)



4/5 0662-837 - ENRev. 2006.06


193 O-ring 29,2x3 1 1331-486 5)

194 O-ring 39,2x3 1 1331-616 5)

195 O-ring 44,2x3 2 1331-617

196 O-ring 49,5x3 2 1331-618 9)

197 O-ring 54,5x3 1 1331-619

199 O-ring 69,5x3 1 1331-620

200 O-ring 79,5x3 1 1331-621

203 O-ring 109,5x3 2(1) 1331-487 9)

204 O-ring 114,5x3 1 1331-622

205 O-ring 124,5x3 1 1331-488 5)

206 O-ring 129,5x3 1 1331-624

207 O-ring 49,2x5,7 2(1) 1331-629 9)

208 O-ring 149,3x5,7 1 1331-489

209 O-ring 159,3x5,7 2 1331-630

210 O-ring 184,3x5,7 2 1331-634

211 O-ring 279,3x5,7 1 1331-638

212 O-ring 119,5x3,0 1 1331-623

214 Hexagon screw M12x35 4 1424-216

216 Hex socket screw 16x45 32 1413-433

219 Lifting eye M30 2 1427-160

223 Grub screw 6x10 2 1413-231






233 Hex. socket screw 10x30 7(5) 1413-372 9)





239 Hex. Socket screw 10x110 3 1413-393 5)






256 Plug 3/8” 2 1343-023

259 Connection Angle 2 1349-233

270 Protecting cover 1 1246-059

275 Solenoid valve with coils 220-240 V AC 1 1372-584 10)

Solenoid valve with coils 110-120 V AC 1 1372-585 10)

Solenoid valve with coils 24 V AC 1 1372-586 10)

Solenoid valve with coils 24 V DC 1 1372-583 10)

Coil 220-240 V AC 2 1921 470-1 10)

Coil 110-120 V AC 2 1921 470-2 10)

Coil 24 V AC 2 1921 470-3 10)



5/50662-837 - ENRev. 2006.06


0662

_837

_EN

G.fm

3) Compressors with economizer

4) Compressors without economizer

5) Only for compressors with variable Vi

6) Only for compressors with variable Vi or fixed Vi = 4.8

7) Only for compressors with fixed Vi = 2.6 or 4.8

8) Only for compressors with fixed Vi = 4.8

9) No. In ( ) for compressors with fixed Vi

9.1) No. In ( ) for compressors with fixed Vi=2,6

10) Depending on pilot voltage

276 Orifice plug 2.0 1 1371-038

277 Orifice plug 2.5 1 1371-039

280 Position transmitter 1 1553-276

281 Bushing for capacity transmitter 1 3043-251

282 Alu pipe for retainer (part of pos. 42) (1) 1116-018

283 Hexagon socketscrew M6x35 2 1413-344

285 Hexagon screw M27x70 12 1424-342


Image1

01.10

0662--835 1/3

Spare Parts for SAB 87 Unit

Relevant drawing: Piping DiagramUnless otherwise stated all measurements are in mmStandard set for UNISAB II Part no. 3084.394Certificate set for UNISAB II Part no. 3084.383

Pos. Designation No. Remarks Part no.

20 Suction side compressorGasket set for SVA 100 1 R717Gasket 1 2356-225

22 Discharge side compressorGasket 1 Discharge pipe 2356--225Oil Inlet compressorGasket 1 Flange - Oil inlet 2356--221

28 Safety valve Part no.

Safety valve Part no. according to orderspecification

Gasket set Nipple/Flange -- Part no. accord-ing to order specification

30 Selection of heating cartridgeHeating cartridge 115 V 2 Oil separator 3181--039Heating cartridge 230 V 2 Oil separator 3181--040Heating cartridge 250 V 2 Oil separator 3181--038Sealing ring - heating cartridge 2 Oil separator 1349--213Sight glass

31 O-ring 3 Sight glass 1331--14031 Sight glass 3 Oil separator 1226--01732 Selection of oil cooler OWSG

Gasket 270/150 x 5.0 2 OWSG 16xx 2355--171Gasket - free of asbestos 2 OWSG 16xx 2357--014Aluminium gasket 1 OWSG 16xx 2356--141Aluminium gasket 1 OWSG 27xx 2356--141Rubber gasket 2 OWSG 27xx 2356--173O-ring 8 OWSG 27xx 1331--028Gasket - free of asbestos 2 OWSG 27xx 2357--016

0662--8352/3


32 Aluminium gasket 1 OWSG 32xx 2356--141Rubber gasket 2 OWSG 32xx 2355--174O-ring 8 OWSG 32xx 1331--028Gasket - free of asbestos 2 OWSG 32xx 2357--017Aluminium gasket 1 OWSG 41xx 2356--141Rubber gasket 2 OWSG 41xx 2355--175O-ring 8 OWSG 41xx 1331--041Gasket - free of asbestos 2 OWSG 41xx 2357--018Gasket sets SVA15 and SNV 8

48--50--54--64 Gasket set 7 SNV 8 2453--053

39 Oil filterElement 1 1517-015O--ring 1 Cover 1331-175Al--gasket 1 Air--purging 2356-127O--ring 1 1331-169O--ring 1 Element 1331-225

38-42 Gasket set 2 Stop valve SVA 50 3184-07746 Thermostatic 3 way--valve

O-ring 1 Thermostatic three-way valveRT6 1331--273

Thermo-element 1 Thermostatic three-way valve -RT6 1365--084

PTFE-ring 1 Thermostatic three-way valve -RT6 1331--306

Filter elements Oil Separator55 Filter element-- RHC 5000--1 2 Oil separator 1517--13055 O-ring 2 Cover for oil separator 1331--19252 Oil return system

Nozzle valveSight glassGasket dia. 40,5/33 x 1,5

1364--1511226--0142356--144

97 Economizer portGasket 1 Economizer 2356--222

203 Gasket setselection of non return valveGasket set -- Non return valveDischarge outlet

2 Part no. according to orderspecification

0662--835 3/3


204 Gasket setselection of discharge valveGasket set for SVA 100 2 Discharge outlet valve 3184--079

FT209 Level Switch (not standard)Oil level Switch 1 Oil Seperator 4514--012

210 Selection of non-return valveO-ring-- ZRK--S DN 87 1 Oil by-pass - Non-return valve 1331--086

220 GasketGasket

11

POV system 2356--2222356--221

228 Coupling and Coupling Guarde

Spare parts set 1 Disk set - setting plugs - nuts -washer 1524--128

Grub screw M10x30 1 Coupling series 52 size 375 1413--192Coupling Guarde 1 Inner part 2158-299Coupling Guarde 1 Outer part 2158-300Coupling Guarde 1 Adaptor plate incl. screws 2158-342

0662-832 rev. 00.05

page 1 of 1

Spare Parts for service onSAB 87 compressorThe spare parts listed below are needed for thefollowing service jobs. For separate gaskets oritems -see part list for compressor Document no.0662-831The relevant drawing document: 0662-830

Cleaning of suction filterPart no. 3084-719No. Designation Pos. no. Remarks2 Gasket 762 Gasket 127 D=109/95x21 O-ring 211 279,3x5,7

Change of seal for visual positionindicatorPart no. 3084-706No. Designation Pos. no. Remarks1 Sealing ring 1731 Support ring 561 O-ring 191 19,2x31 O-ring 195 44,3x31 O-ring 206 129,5x3

Change of seal for indication of Vi-pistonPart no. 3084-835No. Designation Pos. no. Remarks1 Sealing ring 1741 Support ring 661 O-ring 193 29,2x31 O-ring 205 124.5x3

Inspection of rotorsPart no. 3084-720No. Designation Pos. no. Remarks1 Gasket 602 Gasket 761 Gasket 882 Gasket 127 D=109/95x21 O-ring 211 279.3x5,7

Change of oil pumpPart no. 3084-717No. Designation Pos. no. Remarks1 Oil pump 951 Gasket 962 Tension pin 130 6x16

Change of shaft sealPart no. 3084-716No. Designation Pos. no. Remarks1 Shaft seal 181 O-ring 203 109.5x31 O-ring 204 114.3x31 V-ring 1841 Gasket 271 Gasket 167

Capacity control

No. Designation Pos. no. Remarks1 240 V/60 Hz1921 438-1 220 V/50 Hz1 120 V/60 Hz1921 438-2 110 V/50 Hz1

Completesolenoid valvebut withoutorifices

1921 438-3 24 V/50-60 Hz2 240 V/60 Hz1921 470-1 220 V/50 Hz2 120 V/60 Hz1921 470-2 110 V/50 Hz2

Coil

1921 470-3 24 V/50-60 Hz1 Orifice conn. P 277 Ø 2,3 mm1 Orifice conn. T 276 Ø 2,0 mm4 O-ring 9,25x1,78

Change of bearing or complete overhaulPart no. 3084-548No. Designation Pos. no. Remarks1 Set of gaskets 3084-7011 Radial bearing 111 Radial bearing 122 Radial bearing 133 Thrust bearing 142 Thrust bearing 151 Shaft seal kit 18 3084-7161 Shim 34 0.1

0662-804 rev. 99.12

page 1 of 1

Small tool set for SAB 81- 83 – 85 – 87 - 89 compressorsThis tool set contains the tools needed to align the electric motor, to replace a shaft seal, to replace avisual indicator seal and to replace a coupling. Each compressor should be provided with this tool set.For major overhaul work (replacing bearings e.g.), this tool set must be supplemented with the large toolset – see doc.no. 0662-803 (SAB 81), 0662-813 (SAB 83) , 0662-823 (SAB 85) , 0662-833 (SAB 87) or0662-843 (SAB 89).

List of tools in the tool set 3083.189Item quantity Article no. Designation

1 1 1906 139-1 Tool box2 1 3183.105 Alignment device for coupling3 2 1622.050 Feeler gauge (incl. In 3183.105)4 1 1906 152-1 Level arm5 2 1906 153-1 Puller screw6 2 1906 154-1 Guiding pin7 1 1906 155-1 Dismantling tool8 2 1905 156-1 Puller screw9 1 1906 157-A Guide15 2 1906 140-15 Screw M14x4016 2 1906 140-16 Nut M1217 2 1906 140-17 Nut M618 1 1906 140-18 Hexagon key 4 mm19 1 1906 140-19 Hexagon key 5 mm20 1 1906 140-20 Hexagon key 12 mm21 2 1906 140-21 Socket-head sleeve 6 mm22 1 1906 140-22 Socket-head sleeve 8 mm23 1 1906 140-23 Socket-head sleeve 10 mm

0662-833 rev. 00.05

page 1 of 2

Large tool set for SAB 87 compressorsThe tools specified below are needed for major overhauls and repairs (e.g. service after 40 000 operatinghours or changing bearings). These tools named the large tool set must be supplemented with the so-called small tool set article no. 3083.189. See Document no. 0662-804

List of tools in the tool set 1906 147-AItem quantity Article no. Designation

1 1 1906 147-1 Tool box2 1 1906 380-A Sleeve for bearing nut ,screw3 1 1906 481-A Sleeve for bearing nut, slide4 1 1906 490-1 Yoke5 1 1906 491-1 Level arm6 2 1906 454-A Holder7 1 1906 455-A Holder8 1 1906 456-A Holder9 2 1906 136-1 Tie rod10 1 1906 137-1 Tie rod12 1 1906 075-1 Dismounting tool for radial bearing13 1 1906 094-1 Dismounting tool for radial bearing14 1 1906 095-1 Dismounting tool for radial bearing15 1 1906 098-1 Sleeve16 1 1906 484-1 Assembling tool for bearing17 1 1906 485-1 Washer18 1 1906 486-1 Adapter20 1 1906 488-1 Guide21 1 1906 489-1 Guide22 1 1906 138-1 Level arm23 1 1906 478-1 Guide24 1 1906 478-2 Guide25 1 1906 478-3 Guide26 1 1906 492-1 Guide32 1 1878 747-A Feeler gauge33 1 1906 147-33 Retaining-ring pliers34 1 1906 147-34 Socket head sleeve35 1 1906 147-35 Socket head sleeve36 1 1906 147-36 Socket head sleeve37 1 1906 147-37 Socket head sleeve38 1 1906 147-38 Adapter40 1 1906 147-40 Hexagon socket screw key41 1 1906 147-41 Ratched-ring key42 2 1906 144-42 Flange nut43 1 1906 147-43 Flange nut45 1 1906 147-45 Thrust bearing47 1 3921 8333 534 Lifting eye48 1 3921 8333 670 Lifting eye50 4 3921 2120 532 Screw51 1 1906 147-51 Hexagon screw52 1 1906 147-52 Hexagon screw55 1 1906 147-55 Grub screw60 2 1905 777-1 Guide

0662-833 rev. 00.05

page 2 of 2

Weight 60 kg

Documents

Spare parts manual SAB 87 - Sabroe