Modlling of General arrangement of Tool Holder by CATIA

General arrangement of Tool Holder 2010MME007

1

A

DOCUMENTATION ON

“GENERAL ARRANGEMENT OF TOOL HOLDER”

By

GORE ABHAY S.

Reg. No: 2010MME007

M.Tech. (Mech-CAD/CAM) - I

Under the guidance of

Mr. R. P. PARVEKAR

Department of Production Engineering


2

DIFFERENT PARTS OF THE GENERAL ARRANGEMENT OF TOOLHOLR ARE AS

FOLLOWS

1. TOOL HODER

2. BASE PLATE

3. MOVER

4. HANDLE

5. KNOB

6. STUD

7. SET SCREW

8. SPRING

9. WASHER

10. GRUB SCREW

11. BALL

12. ASSEMBLY

13. Drafting


3

The procedure of drawing above parts in UGNX is explained below

For starting NX 4.0 begin with the following commands

Start-ALL ProgramsUGSNX4.0NX4.0CLICK


4


5

NX MAIN PAGE APPEARS AS SHOWN IN FIG

TOOL HODER

CREATE NEW FILEFROM NEW OPTION FILE NAMETOOL HOLDER


6

MAIN SCREEN OF NX4.0 APPEARS


7

GO TO START MENUSELECT MODELLING OPTION (CTRL+M)


8

AFTER SELECTING THE MODELING OPTION THE SCREEN APPEARS AS SHOWN

BELOW

FOR CREATING NEW DRAWING GO TO SKETCHSELECT PLANEOK


9

SELECT THE PLNE OF DRAWING AND CLICK OK AS SHOWN BELOW

GO TO SKETCH CURVE SELECT LINE OPTION AND START FIGURE


10

DIMENSIONS GIVEN BY INFERRED DIMENSIONS OPTION (D)

AFTER SELECTING THE LINE COMMAND FROM THE SKETCH CURVE DIALOG BOX

DRAW THE FIGURE AS PER GIVEN DIMENSIONS BY SELECTING APPROPRIATE CO-

ORDINATE AXIS AS SHOWN BELOW AND APPLY DIMENSIONS AS PER SKETCH.


11

AFTER DRAWING THE SKETCH SELECT FINISH SKETCH OPTION.

AFTER GO TO FORM FEATURE EXTRUDE COMMAND AND EXTRUDE SKETCH

AS PER GIVEN DIMENSIONS


12

AGAIN GO TO SKETCHSELECT PLANESELECT REQUIRED PLANE FROM

EXTRUDE FIGURE AND DRAW REQUIRED SKETCH WITH


13

DIMENSIONS.


14

AFTER DRAWING THE SKETCH SELECT FINISH SKETCH OPTION.




15


16

SELECT ANOTHER PANE


17

AFTER GO TO FEATURE OPERATION HOLE

HOLE DIALOGUE BOX APPEARS AS SHOWM BELOW


18

GIVE REQUIRED DIMENTIONS OF HOLE SELECT THESRFACE WHERE HOLE IS TO

BE DRAWN THEN CLICK “OK”

POSITIONING DIALOGUE BOX APPERAS

WITH THE HELP OF HORIZONTAL AND VERTICAL POSITIONING OPTIONS OCATE

HONE AS PER DIMENSIONS


19

THEN CLICK “OK”


20

FOR NEXT HOE USE SAME PROCEDURE


21

THEN GO TO INSTANCES AND CHOOSE REACTANGULAR ARRAYIT LOOK AS

SEECT THE HOLE TO BE USED


22

ENTER THE PARAMETERS ALONG APPROPRIATE AXIS

CLICK ON YES


23

ENTER THE POSITIONING PARAMETERS

T

HEN PART WILL LOOK AS

SELECT OTHER PLANE AS SHOWN


24

GO TO HOLE AND GIVE THE POSITIONS OF HOLE


25

CLICK ON OK


26

AGAIN GO FOR HOLE GIVE THE POSITION AND CLICK ON OK


27


28


29

GO THREAD ENTER THE PARAMETERS IT LOOK AS


30

CLICK ON OK THE PART IS AS


31


32


33

DOCUMENTATION OF BASE PLATE


34

“OK”



35

GO TO FORM FEATURESELECT EXTRUDE COMMAND AND EXTRUDE SKETCH



36

GO TO FORM FEATURESELECT CYINDEROPTION

THEN SELECT DIAMETER, HEIGHT


37

GIVE VECTOR CONSTRUCTOR POSITION OK

THEN GIVE DIAMETER AND HEIGHT OF CYLINDEROK

GIVE THE CENTRE POSITION OF CYLINDEROK


38


39

UNITE BOTH OF THEM


40

GO TO CHAMPER SELECT OFF SET METHOD AS ALOMG THE FAACE AND SELECT

TANGENT CURVE

NOW GO TO HOLE GIVE DIAMETER AND HEIGHT


41

GIVE THE POSITIONS AND CLICK ON OK


42


43

AGAIN GO TO HOLE AND DO THE ALL PROCEDURE ONCE AGAIN


44

GO TO INSTANCES SELECT THE HOLE TO BE ARRAYED


45

ENTER THE PARAMETERS ALON THE REQUIRED AXIS

THEN CLICKON OK AND CREATE INSTANCES


46


47

NOW GO TO HOLE AGAIN GIVE POSITIONS CLICK ON OK


48

GO TO INSTANCES IN IT CLICK ON CIRCULAR ARRAY ENTER NUMBER AND

ANGLE


49

GIVE VECTOR CONSTRAINTS AND CLICK ON OK


50


51

THE FINAL PART WILL LOOK AS


52

GO THREAD ENTER THE PARAMETERS IT LOOK AS


53

“OK”


54

THE FINAL PART LOOK AS


55


56


57

DOCUMENTATION OF MOVER

GO TO FILEFROM NEW OPTION FILE NAME

OK


58


59



60


BELOW



61


BELOW GO TO START MENUSELECT MODELLING OPTION (CTRL+M) .


62

DRAW THE SKETCH AS PER REQUIREMENT SHOWN BELOW

GO TO FORM FEATURE REVOLVE


63

GIVE ANGULAR LIMITS THAT IS START AND END VALUES CLICK ON OK


64

THEN THE SCREEN AS

AFTER GO TO FEATURE OPERATION HOLE

HOLE DIALOGUE BOX APPEARS AS SHOWM BELOW


65

CLICK ON OK


66

GO TO FEATURE OPERATION TOOL BAR EDGE BLEND

FOLLOWING BOX APPEARS


67

GO TO FEATURE OPERATION DATUM PLANE

SELECT THE TYPE AT AN ANGLE GIVE ANGLE


68

“OK”

AGAIN DO THE SAME OPERATION SELECT THE TYPE AS PARALLEL TO


69

GO TO SKETCH CURVE SELECT CIRCLE AND START FIGURE

THEN FINISH SKETCH OPTION.



EXTRUDE DILOGUE BOX APPERS SELECT SKETCHGIVE THE LIMITS GIVE

BOOLEAN OPERATIONOK


70

GO TO FEATURE OPERATIONTOOL BAR SELECT SUBSTRACT

GO TO FEATURE OPERATIONTOOL BAR SELECT THREAD COMMAND

SELECT DETAILED THREAD OPTION


71

CLCK OK THEN FINAL PART WILL BE


72


73


74

DOCUMENTATION OF HANDLE


75

“OK”




76


BELOW GO TO START MENUSELECT MODELLING OPTION (CTRL+M) .

GO TO FORM FEATURESELECT CYINDER OPTION


77

THEN SELECT DIAMETER, HEIGHT.


78

SELECT POINT CONSTRUCTOR


79

OK


80



81



82

THEN SELECT FACE ON WHICH THREAD ARE REQUIRED GIVE REQUIRED

DIMENSIONSOK


83

AT LAST PART LOOK AS


84


85

DOCUMENTATION OF KNOB


OK


86



87


BELOW

NOW GO TO FORM FEATURE SPHERE

THE SCREEN WILL LOOK AS

SELECT DIAMETER, CENTRE OPTION

GIVE DIAMETER AND CLICK ON OK


88


SELECT THE TYPE PARALLEL TO THIS WINDOW LOOK AS


89

ENTER OFFSET PARAMETER CLICK ON OK


90

GO TO FORM FEATURE OPRATIONS TRIM BODY

ENTER OFFSET VALUE OK


91

THEN GO TO FORM FEATER HOLE

GIVE DIAMETER, DEPTH, TIP ANGLE OK


92

“OK”


93

THE FINAL PART WILL LOOK LIKE


94


95


96

DOCUMENTATION OF STUD


OK


97


98



99


BELOW




100

GIVE ANGULAR LIMITS THAT IS START AND END VALUES CLICK ON OK

THEN THE SCREEN AS


101

THE PART WILL LOOK AS


102




103


SELECT THE TYPE AT AN ANGLE GIVE ANGLE


104

“OK”

AGAIN DO THE SAME OPERATION SELECT THE TYPE AS PARALLEL TO


105


106

THE FINAL PART IS AS


107


108


109

DOCUMENTATION OF SET SCREW


OK


110



111


BELOW



112


BELOW


113

GO TO FORM FEATURE BLOCK

ENTER X, Y, Z LENGTHS

GO TO FEATURE OPERATION TOOL BAR EDGE BLEND

FOLLOWING BOX APPEARS


114


115


THEN SELECT DIAMETER, HEIGHT


116




117

THEN THE PART LOK AS


118


119


120

DOCUMENTATION OF SPRING


OK


121


122



123


BELOW



124


BELOW


125

GO OT FORM FEATURE CURVE HEILX OK


126

NOW GO TO FORM FARURE TUBE

GIVE OUTER DIAMETER AND INNER DIAMETER OK


127

THE FINAL PART IS


128


129


130

DOCUMENTATION OF WASHER


OK


131


132



133


BELOW




134

ENTER DIAMETER AND HEIGHT

THEN GO TO FORM FEATER HOLE

GIVE DIAMETER, DEPTH, TIP ANGLE OK


135


136


137


138

DOCUMENTATION OF GRUB SCREW


OK

THE WINDOW LOOK AS


139



140


BELOW


141



142

AGAIN GO TO SKETCHER


143

GO TO FORM FEATURESELECT EXTRUDE COMMAND AND EXTRUDE SKETCH


IN IT CLICK ON TO SUBSTRACT BUTTON

OK


144

GO TO FORM FEATURE THREAD ENTER THE VALUES

THEN THE LAST PART WILL LOOK LIKE


145


146


147

DOCUMENTATION OF BALL


OK

THE WINDOW LOOK AS


148



149


BELOW

NOW GO TO FORM FEATURE SPHERE

THE SCREEN WILL LOOK AS

SELECT DIAMETER, CENTRE OPTION

GIVE DIAMETER AND CLICK ON OK


150

IT WILL BE LIKE AS


151


152


153

DOCUMENTATION OF ASSEMBLY

NX MAIN PAGE APPEARS AS SHOWN IN FIG

CREATE NEW FILEFROM NEW OPTION FILE NAMEASSEMBLY


154

THEN GO TO START ASSEMBLIES


155

GO TO ADD EXISTING PART


156

GIVE THE COMPONENET NAME, REFERANCE SET, POSITIONING AND LAYER OPTION


157

ENTER THE VALUES IN POINT CONSTRUCTOR OK


158


159

IMPORT THE ANOTHER PART AS


160

GIVE THE POSITIONING AS MATE


161

ENTER THE MATING CONDITIONS AS CENTER AND DIETANCE BETWEEN TWO FACES


162

OK

IMPORT ANOTHER PART


163

GIVE THE POSITIONING AS REPOSITION


164

LOOK FOR ANOTHER PART


165

GIVE THE POSITIONING AS MATE, REFERANCE SET AS MODEL, LAYER OPTION ORIGINAL


166

ENTER MATING CONDITIONS AS CENTER, MATE, DISTANCE


167

GOTO ASSEMBLIES CREAT COMPONENT ARRAY OK

GIVE ARRAY DEFINATION AS FROM INSTANCE FEATUREOK


168

IMPORT GRUB SCREW

GIVE POSITIONING CONDITION AS MATE


169

GIVE MATING CONDITIONS AS CENTER, PERPEDICULAR, DISTANCE


170

GOTO ASSEMBLIES CREAT COMPONENT ARRAY OK

GIVE ARRAY DEFINATION AS FROM INSTANCE FEATUREOK

SELECT THE COMPONENT TO ARRAYED


171


172

IMPORT TOOL HOLDER


173

GIVE MATING CONDITION AS CENTER, DISTANCE, PARALLEL

ADD STUD


174

ENTER MATING CONDITION AS DISTANCE

ADD MOVER


175

ENTER MATING CONDITION AS CENTER DISTANCE


176

IMPORT HANDLE

ENTER MATING CONDITION AS CENTER DISTANCE


177

OK

IMPORT KNOB


178

GIVE THE MATIN CONDITION AS CENTER, DISTANCE, PARALLEL

IMPORT SET SCREW


179

ENTER MATING CONDITION AS CENTER, DISTANCE

MAKE MIRROR ASSEMBLY NEXT SELECT COMPONENTOK


180

THEN IT LOOK AS


181


182

Drafting of Tool Holder

Select click on the drafting option or use Crtl+Shift+D

Then the screen will look like


183

Click OK

The drafting window will be as


184

Now go to Base View-OK

The bottom view will be


185

The back view looks like


186

The side view is as


187


188


189


190

For sectional view go to section view select the view to be used then

locate the sectional plane.


191

For part list go to tabular note select part list option, locate the position

for it.


192


193

The part list looks like as given in following window.


194

Go to tabular note auto balloon select the view to used


195

The part with balloon is


196

Documents

Modlling of General arrangement of Tool Holder by CATIA