Embed Size (px)
Citation preview
www.barloworld-equipment.com
© 2019 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, LET'S DO THE WORK, their respective logos, “Caterpillar Yellow,” the “Power Edge” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
FINAL DRIVE & AXLEREPAIR OPTIONS
Barloworld Equipment offers you repair options on selected machines and components, with wear and maintenance, common repair and critical repair solutions that focus on engines, transmissions, cylinders and � nal drives. Repair your machine before failure and avoid unscheduled down time.
[email protected] or [email protected]
Caterpillar repair options
FINAL DRIVE & AXLE REPAIR OPTIONS
INTRODUCTION
ARTICULATED TRUCKS725 ARTICULATED TRUCK730 ARTICULATED TRUCK740 ARTICULATED TRUCK (B1R / B1P)740 ARTICULATED TRUCK (L4E)740 ARTICULATED TRUCK (L4F)
WHEEL LOADERS 950H WHEEL LOADER962H WHEEL LOADER966H WHEEL LOADER988B WHEEL LOADER988H WHEEL LOADER
HYDRAULIC EXCAVATORS 320 HYDRAULIC EXCAVATOR390F HYDRAULIC EXCAVATOR
TRACK TYPE DOZERSD6R TRACK TYPE DOZERD7R TRACK TYPE DOZERD8R TRACK TYPE DOZERD9R TRACK TYPE DOZER
MOTOR GRADERS 140H MOTOR GRADER140K MOTOR GRADER
Caterpillar repair options
INDEXFINAL DRIVE & AXLE REPAIR OPTIONS
725 ARTICULATED TRUCK
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
CENTRE DIFF
725 ARTICULATED TRUCK
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 REMOVE AND INSTALL (installation parts not included)
CENTRE DIFFERENTIAL REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
Friction Disc ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
FINAL DRIVE
725 ARTICULATED TRUCK
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR AND SHAFT-PLANETARYOption 2 GEAR-RINGOption 3 GEAR-SUNOption 4 BRAKE LININGOption 5 LABOUR TO REMOVE AND INSTALL AXLE
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
FRONT & REAR DIFF
725 ARTICULATED TRUCK
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR-DIFFERENTIALOption 2 PINIONOption 3 SPIDEROption 4 GEAR SET-BEVELOption 5 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-FRONT Option 6 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-REAR
FRONT & REAR DIFFERENTIAL REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
Disc Plate ✓
Friction Disc ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
730 ARTICULATED TRUCK
CENTRE DIFF
Caterpillar repair options
RETURN TO CONTENTS PAGE
730 ARTICULATED TRUCK
FINAL DRIVE & AXLE REPAIR OPTIONS
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR SET-BEVELOption 2 PINIONOption 3 GEAR-DIFFERENTIALOption 4 SPIDEROption 5 PINION Option 6 SPIDEROption 7 GEAR-DIFFERENTIAL BEVELOption 8 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-CENTRE
CENTRE DIFFERENTIAL REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
Friction Disc ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
730 ARTICULATED TRUCK
FINAL DRIVE & AXLE REPAIR OPTIONS
FINAL DRIVE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAROption 2 GEAR-RINGOption 3 SHAFT-PLANETARYOption 4 KIT-SEAL (Brakes)Option 5 LABOUR TO REMOVE AND INSTALL FINAL DRIVE-EACH
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Caterpillar repair options
RETURN TO CONTENTS PAGE
730 ARTICULATED TRUCK
FINAL DRIVE & AXLE REPAIR OPTIONS
FRONT & REAR DIFF
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR SET-BEVELOption 2 PINIONOption 3 GEAR-DIFFERENTIALOption 4 SPIDEROption 5 PINION Option 6 SPIDEROption 7 GEAR-DIFFERENTIAL BEVELOption 8 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-FRONTOption 9 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-REAR
FRONT & REAR DIFFERENTIAL REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
Disc Plate ✓
Friction Disc ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
740 ARTICULATED TRUCK (B1R / B1P)
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (B1R / B1P)
CENTRE DIFF
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR SET-BEVEL CENTREOption 2 GEAR SET-BEVEL FRONT AND REAROption 3 GEAR-DIFFERENTIALOption 4 SPIDEROption 5 PINION Option 6 SPIDEROption 7 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-CENTRE
CENTRE DIFFERENTIAL REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
Friction Disc ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (B1R / B1P)
FRONT & REAR DIFF
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR SET-BEVEL CENTREOption 2 GEAR SET-BEVEL FRONT AND REAROption 3 GEAR-DIFFERENTIALOption 4 PINIONOption 5 SPIDEROption 6 PINIONOption 7 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-REAROption 8 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-FRONT
FRONT & REAR DIFFERENTIAL REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
Disc Plate ✓
Friction Disc ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (B1R / B1P)
FINAL DRIVE FRONT & CENTRE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 SHAFT-PLANETARYOption 2 GEAR-RINGOption 3 FRICTION DISCOption 4 LABOUR TO REMOVE AND INSTALL FINAL DRIVE-EACH
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (B1R / B1P)
FINAL DRIVE REAR
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 SHAFT-PLANETARYOption 2 GEAR-RINGOption 3 FRICTION DISCOption 4 LABOUR TO REMOVE AND INSTALL FINAL DRIVE-EACH
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
740 ARTICULATED TRUCK (L4E)
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (L4E)
FRONT, CENTRE & REAR DIFF
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR SET-BEVEL Option 2 GEAR AS DIFFERENTIAL 3389635Option 3 GEAR AS DIFFERENTIAL 3389638Option 4 PINIONOption 5 SHAFT GEAROption 6 SPIDEROption 7 BEARING AND SEAL AXLE YOKE TO REAR AXLEOption 8 LABOUR TO REMOVE AND INSTALL DIFF-FRONT (installation parts not included)Option 9 LABOUR TO REMOVE AND INSTALL DIFF-CENTRE (installation parts not included)Option 10 LABOUR TO REMOVE AND INSTALL DIFF-REAR (installation parts not included)
FRONT, CENTRE & REAR DIFFERENTIAL REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
Friction Disc ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (L4E)
FINAL DRIVE FRONT & CENTRE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 SHAFT-PLANETARYOption 2 GEAR-RINGOption 3 HUB ASOption 4 LABOUR TO REMOVE AND INSTALL (installation parts not included)Option 5 BRAKES
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (L4E)
FINAL DRIVE REAR
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 SHAFT-PLANETARYOption 2 GEAR-RINGOption 3 HUB ASOption 4 LABOUR TO REMOVE AND INSTALL (installation parts not included)Option 5 BRAKES
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
740 ARTICULATED TRUCK (L4F)
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (L4F)
FRONT, CENTRE & REAR DIFF
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR SET-BEVEL Option 2 GEAR AS DIFFERENTIAL 3389635Option 3 GEAR AS DIFFERENTIAL 3389638Option 4 PINIONOption 5 SHAFT GEAROption 6 SPIDEROption 7 BEARING AND SEAL AXLE YOKE TO REAR AXLEOption 8 LABOUR TO REMOVE AND INSTALL FRONT DIFF (installation parts not included)Option 9 LABOUR TO REMOVE AND INSTALL CENTRE DIFF (installation parts not included)Option 10 LABOUR TO REMOVE AND INSTALL REAR DIFF (installation parts not included)
FRONT, CENTRE & REAR DIFFERENTIAL REPAIR OPTIONS LEVEL 1
Bearings ✓
Plate ✓
Seals ✓
Friction Disc ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (L4F)
FINAL DRIVE FRONT & CENTRE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 SHAFT-PLANETARYOption 2 GEAR-RINGOption 3 HUB ASOption 4 LABOUR TO REMOVE AND INSTALL (installation parts not included)Option 5 BRAKES
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
740 ARTICULATED TRUCK (L4F)
FINAL DRIVE REAR
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 SHAFT-PLANETARYOption 2 GEAR-RINGOption 3 HUB ASOption 4 LABOUR TO REMOVE AND INSTALL (installation parts not included)Option 5 BRAKES
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
950H WHEEL LOADER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
950H WHEEL LOADERLOADER
FRONT AXLE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 PINION-DIFFERENTIAL BEVEL Option 2 GEAR-DIFFERENTIAL LIMITED SLIPOption 3 PINION-BEVEL LIMITED SLIPOption 4 SHAFT PINION-LIMITED SLIPOption 5 GEAR-BEVELOption 6 SHAFT BEVEL PINIONOption 7 GEAR-RINGOption 8 GEAR-SUNOption 9 GEAR AND SHAFT-PLANETARYOption 10 LABOUR TO REMOVE AND INSTALL AXLE (installation parts not included)
FRONT AXLE LEVEL 1
Bearings ✓
Seals ✓
Friction Disc ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
950H WHEEL LOADERLOADER
REAR AXLE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 PINION-DIFFERENTIAL BEVEL Option 2 GEAR DIFFERENTIAL LIMITED SLIPOption 3 PINION-BEVEL LIMITED SLIPOption 4 SHAFT PINION-LIMITED SLIPOption 5 GEAR-BEVELOption 6 SHAFT BEVEL PINIONOption 7 GEAR-RINGOption 8 GEAR-SUNOption 9 GEAR AND SHAFT-PLANETARYOption 10 LABOUR REMOVE AND INSTALL AXLE (installation parts not included)
REAR AXLE LEVEL 1
Bearings ✓
Seals ✓
Friction Disc ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
962H WHEEL LOADER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
962H WHEEL LOADER
FRONT AXLE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR AND SHAFT-PLANETARYOption 2 GEAR-RINGOption 3 GEAR-SUNOption 4 PINION-DIFFERENTIAL BEVELOption 5 GEAR-DIFFERENTIALOption 6 GEAR SET-BEVELOption 7 LABOUR TO REMOVE AND INSTALL AXLE
FRONT AXLE LEVEL 1
Bearings ✓
Reaction Plate ✓
Disc Plate ✓
Friction Disc ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
962H WHEEL LOADER
REAR AXLE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR AND SHAFT-PLANETARYOption 2 GEAR-RINGOption 3 GEAR-SUNOption 4 PINION-DIFFERENTIAL BEVELOption 5 GEAR-DIFFERENTIALOption 6 SHAFT-PINIONOption 7 LABOUR TO REMOVE AND INSTALL AXLE
REAR AXLE LEVEL 1
Bearings ✓
Reaction Plate ✓
Disc Plate ✓
Friction Disc ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
966H WHEEL LOADER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
966H WHEEL LOADER
FRONT AXLE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 REMOVE AND INSTALL FRONT AXLE HOUSING ASSEMBLYOption 2 GEAR-PLANETARYOption 3 GEAR-RINGOption 4 GEAR-SUNOption 5 GEAR-DIFFERENTIAL BEVELOption 6 PINION-DIFFERENTIAL BEVELOption 7 GEAR-BEVEL Option 8 FRICTION DISC TYPE 1Option 9 FRICTION DISC TYPE 2
FRONT AXLE LEVEL 1
Bearings ✓
Seals ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
966H WHEEL LOADER
REAR AXLE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 REMOVE AND INSTALL FRONT AXLE HOUSING ASSEMBLYOption 2 GEAR-PLANETARYOption 3 GEAR-RINGOption 4 GEAR-SUNOption 5 GEAR-DIFFERENTIAL LIMITED SLIPOption 6 GEAR SET-BEVELOption 7 GEAR-DIFFERENTIAL BEVEL DIFFERENTIAL STANDARD Option 8 FRICTION DISC TYPE 1Option 9 FRICTION DISC TYPE 2
REAR AXLE LEVEL 1
Bearings ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
988B WHEEL LOADER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
988B WHEEL LOADER
FRONT & REAR DIFF
988B WHEEL LOADER
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 BEVEL GEAR-DIFFERENTIAL AND BEVEL GEAROption 2 BEVEL GEAR-DIFFERENTIAL AND BEVEL GEAROption 3 PINION SHAFT-DIFFERENTIAL AND BEVEL GEAR S/N 50W7747-10993Option 4 PINION SHAFT-DIFFERENTIAL AND BEVEL GEAR S/N 50W10994-99999Option 5 PINION SHAFT-DIFFERENTIAL AND BEVEL GEAR S/N 50W1-TO 50W4430 AND
50W4430 AND UPOption 6 PINION-DIFFERENTIAL (SPIDER GROUP) 50W6041 – UPOption 7 GEAR-DIFFERENTIAL Option 8 SPIDER SHAFTOption 9 GEAR-DIFFERENTIALOption 10 PINION-DIFFERENTIAL (SPIDER GROUP) 50W1-4421, 4424, 4426 AND 50W4429Option 11 GEAR-DIFFERENTIALOption 12 SPIDER SHAFTOption 13 BEARING-THRUST OSCILLATIONOption 14 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-EACH
FRONT & REAR DIFFERENTIAL LEVEL 1
Bearings ✓
Seals ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
988B WHEEL LOADER
FINAL DRIVE EACH
988B WHEEL LOADER
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 BRAKES EXTENDED LIFE FRICTION DISCOption 2 BRAKES STANDARD LIFE FRICTION DISCOption 3 GEAR-RINGOption 4 SHAFT-PLANETARYOption 5 GEAR-PLANETARYOption 6 SPINDLE-WHEELOption 7 LABOUR TO REMOVE AND INSTALL FINAL DRIVE AND BRAKES-EACH
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
988H WHEEL LOADER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
988H WHEEL LOADER
FRONT & REAR DIFF
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR-BEVELOption 2 PINION-DIFFERENTIAL BEVELOption 3 GEAR-DIFFERENTIAL BEVELOption 4 SHAFT-BEVEL PINIONOption 5 SPIDEROption 6 SHAFT-BEVEL PINIONOption 7 BEARING-THRUST OSCILLATIONOption 8 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-EACH
FRONT & REAR DIFFERENTIAL REPAIR OPTIONS LEVEL 1
Bearings ✓
Seals ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
988H WHEEL LOADER
FINAL DRIVE EACH
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 SPINDLEOption 2 CARRIER-PLANETARYOption 3 GEAR-RINGOption 4 HUB ASOption 5 GEAR-PLANETARYOption 6 GEAR-SUNOption 7 SHAFTOption 8 LABOUR TO REMOVE AND INSTALL FINAL DRIVE AND BRAKES-EACH
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Friction Disc ✓
Final Drive Brake Kit ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
320 HYDRAULIC EXCAVATOR
Caterpillar repair options
RETURN TO CONTENTS PAGE
320 HYDRAULIC EXCAVATOR
FINAL DRIVE & AXLE REPAIR OPTIONS
FINAL DRIVE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR-COUPLINGOption 2 GEAR AND SHAFT-PLANETARY TYPE 1Option 3 GEAR AND SHAFT-PLANETARY TYPE 2Option 4 GEAR-SUNOption 5 GEAR-SUNOption 6 LABOUR TO REMOVE AND INSTALL FINAL DRIVE-EACH
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Shims ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
390F HYDRAULIC EXCAVATOR
Caterpillar repair options
RETURN TO CONTENTS PAGE
390F HYDRAULIC EXCAVATOR
FINAL DRIVE & AXLE REPAIR OPTIONS
FINAL DRIVE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR AND SHAFT-PLANETARY TYPE 1Option 2 GEAR AND SHAFT-PLANETARY TYPE 2Option 3 GEAR-RING TYPE 1Option 4 GEAR-RING TYPE 2Option 5 GEAR-SUN TYPE 1Option 6 GEAR-SUN TYPE 2Option 7 GEAR-SUN TYPE 3Option 8 GEAR AND SHAFT-PLANETARY TYPE 3Option 9 LABOUR TO REMOVE AND INSTALL FINAL DRIVE-EACH
FINAL DRIVE REPAIR OPTIONS LEVEL 1
Bearings ✓
Shims ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
D6R TRACK TYPE DOZER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
D6R TRACK TYPE DOZER
FINAL DRIVE & DIFF DRIVE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR-RING FINAL DRIVEOption 2 GEAR-PLANETARY FINAL DRIVEOption 3 SHAFT-PLANETARY FINAL DRIVEOption 4 GEAR-SUN FINAL DRIVEOption 5 SPINDLE FINAL DRIVEOption 6 GEAR AS-SUNOption 7 GEAR AND SHAFT-PLANETARYOption 8 GEAR AND SHAFT-PLANETARYOption 9 GEAR-RINGOption 10 GEAR SET-BEVELOption 11 LABOUR TO REMOVE AND INSTALL FINAL DRIVE
FINAL DRIVE & DIFF DRIVE LEVEL 1
Bearings ✓
Friction Disc ✓
Plate-Clutch and Brake ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
D6R TRACK TYPE DOZER
FINAL DRIVE BRAKE & PLANETARY
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR-RINGOption 2 GEAR-PLANETARYOption 3 SHAFT-PLANETARYOption 4 GEAR-SUNOption 5 SPINDLEOption 6 GEAR-PLANETARYOption 7 GEAR AS-SUNOption 8 SHAFT-PLANETARYOption 9 GEAR-RINGOption 10 LABOUR TO REMOVE AND INSTALL FINAL DRIVE
FINAL DRIVE BRAKE & PLANETARY LEVEL 1
Bearings ✓
Friction Disc ✓
Plate-Clutch and Brake ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
D7R TRACK TYPE DOZER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
D7R TRACK TYPE DOZER
FINAL DRIVE BRAKES & DIFFERENTIAL STEER
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR AS-SUN BRAKE AND DIFFERENTIAL STEEROption 2 GEAR-BEVEL BRAKE AND DIFFERENTIAL STEEROption 3 GEAR-RING BRAKE AND DIFFERENTIAL STEEROption 4 SHAFT-PLANETARY BRAKE AND DIFFERENTIAL STEEROption 5 SHAFT-PLANETARY BRAKE AND DIFFERENTIAL STEEROption 6 GEAR-FINAL DRIVEOption 7 GEAR-FINAL DRIVEOption 8 GEAR-FINAL DRIVEOption 9 GEAR-PLANETARY FINAL DRIVEOption 10 SHAFT-PLANETARY FINAL DRIVEOption 11 LABOUR TO REMOVE AND INSTALL FINAL DRIVE
FINAL DRIVE & DIFFERENTIAL STEER LEVEL 1
Bearings ✓
Friction Disc ✓
Plate-Clutch and Brake ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
D7R TRACK TYPE DOZER
FINAL DRIVE BRAKES & PLANETARY
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR AS-SUN BRAKE AND PLANETARYOption 2 GEAR-PLANETARY BRAKE AND PLANETARYOption 3 GEAR-RING BRAKE AND PLANETARYOption 4 GEAR-FINAL DRIVEOption 5 GEAR-FINAL DRIVEOption 6 GEAR-FINAL DRIVEOption 7 GEAR-PLANETARY FINAL DRIVEOption 8 SHAFT-PLANETARY FINAL DRIVEOption 9 LABOUR TO REMOVE AND INSTALL FINAL DRIVE
FINAL DRIVE BRAKE & PLANETARY LEVEL 1
Bearings ✓
Friction Disc ✓
Plate-Clutch and Brake ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
D8R TRACK TYPE DOZER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
Caterpillar repair options
D8R TRACK TYPE DOZER
FINAL DRIVE BRAKES & DIFFERENTIAL
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR-BEVEL BRAKE AND DIFFERENTIAL DRIVEOption 2 GEAR-PLANETARY BRAKE AND DIFFERENTIAL DRIVEOption 3 GEAR-RING BRAKE AND DIFFERENTIAL DRIVEOption 4 GEAR-RING BRAKE AND DIFFERENTIAL DRIVEOption 5 GEAR-SUN BRAKE AND DIFFERENTIAL DRIVEOption 6 PINION-BEVEL BRAKE AND DIFFERENTIAL DRIVEOption 7 GEAR-PLANETARY BRAKE AND DIFFERENTIAL DRIVEOption 8 SHAFT-FINAL DRIVEOption 9 GEAR-RING FINAL DRIVEOption 10 GEAR-SUN FINAL DRIVEOption 11 GEAR-SUN FINAL DRIVEOption 12 SPINDLE FINAL DRIVEOption 13 GEAR-PLANETARY FINAL DRIVEOption 14 LABOUR TO REMOVE AND INSTALL AXLE
FINAL DRIVE BRAKES & DIFFERENTIAL LEVEL 1
Bearings ✓
Friction Disc ✓
Plate-Clutch and Brake ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
Caterpillar repair options
D8R TRACK TYPE DOZER
FINAL DRIVE BRAKES & PLANETARY
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR AS-BRAKE AND PLANETARYOption 2 GEAR-PLANETARY BRAKE AND PLANETARYOption 3 GEAR-RING BRAKE AND PLANETARYOption 4 SHAFT-FINAL DRIVEOption 5 GEAR-RING FINAL DRIVEOption 6 GEAR-SUN FINAL DRIVEOption 7 GEAR-SUN FINAL DRIVEOption 8 SPINDLE FINAL DRIVEOption 9 GEAR-PLANETARY FINAL DRIVE Option 10 LABOUR TO REMOVE AND INSTALL AXLE
FINAL DRIVE BRAKES & PLANETARY LEVEL 1
Bearings ✓
Friction Disc ✓
Plate-Clutch and Brake ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
D9R TRACK TYPE DOZER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
D9R TRACK TYPE DOZER
FINAL DRIVE & STEERING CLUTCH
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR-PLANETARYOption 2 GEAR-RINGOption 3 GEAR-SUNOption 4 GEAR-SUNOption 5 GEAR-PLANETARYOption 6 CARRIER-PLANETARYOption 7 CARRIER-PLANETARYOption 8 CARRIER-PLANETARYOption 9 SPINDLE Option 10 LABOUR TO REMOVE AND INSTALL AXLE
FINAL DRIVE & STEERING CLUTCHES LEVEL 1
Bearings ✓
Friction Disc ✓
Plate-Clutch and Brake ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
140H MOTOR GRADER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
DIFF
140H MOTOR GRADER
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 SPIDEROption 2 PINION ASOption 3 GEAR-BEVEL SPIDEROption 4 GEAR-BEVEL SPIDEROption 5 SHAFT-PINIONOption 6 GEAR-BEVELOption 7 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-EACH
DIFFERENTIAL LEVEL 1
Bearings ✓
Friction Disc ✓
Seals ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
140H MOTOR GRADER
FINAL DRIVE & BRAKE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR-PLANETARYOption 2 GEAR-RINGOption 3 SHAFT-SUN GEAROption 4 LABOUR TO REMOVE AND INSTALL FINAL DRIVE
FINAL DRIVE & BRAKE LEVEL 1
Bearings ✓
Shims ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
140H MOTOR GRADER
SPINDLE BRAKE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 LABOUR TO REMOVE AND INSTALL SPINDLE (BRAKES)-EACH
SPINDLE BRAKE LEVEL 1
Bearings ✓
Friction Disc ✓
Disc ✓
Shims ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
140K MOTOR GRADER
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
Caterpillar repair options
140K MOTOR GRADER
DIFF
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 SPIDEROption 2 PINION ASOption 3 GEAR-BEVEL SPIDEROption 4 GEAR-BEVEL SPIDEROption 5 SHAFT-PINIONOption 6 GEAR-BEVELOption 7 LABOUR TO REMOVE AND INSTALL DIFFERENTIAL-EACH
DIFFERENTIAL LEVEL 1
Bearings ✓
Friction Disc ✓
Seals ✓
* Any options not included in the repair level will incur an additional cost if problems are encountered during the commissioning or at the Dyno test (level dependent) upon natural agreement
* Above options include parts and labour
* Parts kits only are available on request
Terms and conditions:• Transportation / travel time / mileage not included
on all levels and options• Customer to provide lifting equipment (where
required)• All prices are � xed for speci� c marketing period• All prices are excluding VAT• Component must be in a working condition
(transmission must be a runner) (oil samples to be provided). Transmission to be clean on delivery
• Commissioning documents to be completed when installing transmission
• Oil sample to be taken at 50 hours• Re-man pricing is based on full core credit• Removal and installation costs and parts not
included• All prices are � xed for a speci� c marketing period
and are subject to change
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
Caterpillar repair options
140K MOTOR GRADER
FINAL DRIVE & BRAKE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 GEAR-PLANETARYOption 2 GEAR-RINGOption 3 SHAFT-SUN GEAROption 4 LABOUR TO REMOVE AND INSTALL FINAL DRIVE
FINAL DRIVE & BRAKE LEVEL 1
Bearings ✓
Shims ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
Caterpillar repair options
RETURN TO CONTENTS PAGE
FINAL DRIVE & AXLE REPAIR OPTIONS
Caterpillar repair options
140K MOTOR GRADER
SPINDLE BRAKE
ADD-ON OPTIONS FOR REPAIR LEVELS
Option 1 LABOUR TO REMOVE AND INSTALL SPINDLE (BRAKES)-EACH
SPINDLE BRAKE LEVEL 1
Bearings ✓
Friction Disc ✓
Disc ✓
Shims ✓
Seals ✓
* Disassembled parts and items noted under visual inspection will be compared to Caterpillar re-usability guidelines.
* Parts found not to meet the re-usability guidelines will be replaced or reconditioned at an additional cost.
www.barloworld-equipment.com
© 2019 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, LET'S DO THE WORK, their respective logos, “Caterpillar Yellow,” the “Power Edge” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
