View
218
Download
0
Category
Preview:
Citation preview
50 T: 800.628.8139 or 508.946.6200 F: 508.946.6262 www.brookfieldengineering.com
Primary CharacteristicsPARAMETER SENSORIAL DEFINITION INSTRUMENTAL DEFINITION
HARDNESS
SPRINGINESS
ADHESIVENESS
COHESIVENESS
Force required to compress a food between molars. Dened as force necessary to attain given deformation.Rate at which a deformed material goes back to its undeformed condition after deforming force is removed.
The work necessary to overcome the attractive forces between the surface of the food and the surface of other materials with which the food comes into contact (e.g. tongue, teeth, palate). Work required to pull food away from a surface.The strength of internal bonds making up the body of the product (greater the value the greater the cohesiveness)
Peak force of the rst compression cycle.
Height that the food recovers during the time that elapses between the end of the rst bite and the start of the second bite.The negative area for the rst bite, representing the work necessary to pull compressing probe away from sample.
The ratio of positive force during the second to that of the rst compression cycle (downward strokes only)
*Parameters utilized in determining the manner in which a food handles and behaves in the mouth. PARAMETERS AS DENOTED WITHIN ORIGINAL SZCZESNIAK et al (1963) AND BOURNE (1978) TPA WORK
Secondary CharacteristicsPARAMETER SENSORIAL DEFINITION INSTRUMENTAL DEFINITION
BRITTLENESS(Fracture force)
GUMMINESS
CHEWINESS
The first significant break in the first compression cycle.
Calculated parameter: Product of Hardness x Cohesiveness
Calculated Parameter: Product of Gumminess x Springiness (essentially primary parameters of Hardness x Cohesiveness x Springiness)
Force at which a material fractures. Related to the primary parameters of hardness and cohesiveness, where brittle materials have low cohesiveness. Not all foods fracture and thus value may relate to hardness if only single peak is present. Brittle foods are never adhesive.Energy required to disintegrate a SEMI-SOLID food product to a state ready for swallowing. Related to foods with low hardness levels.Energy required to chew a SOLID food product to a state where it is ready for swallowing. attribute is di�cult to quantify precisely due to complexities of mastication (shear, compression, tearing and penetration).
BROOKFIELD TEXTURE ANALYZER
What is texture analysis?Texture analysis is primarily concerned with the evaluation of mechanical characteristics where a material is subjected to a controlled force from which a deformation curve of its response is generated. These mechanical characteristics in food can be further sub-divided into primary and secondary sensory characteristics which have proven to be correlated to sensory perception.
51
Brookfield now offers a complete bath system for processing gelatin samples in batches of 12 Bloom bottles. This system complies with GMIA and GME gelatin processing requirements, and the Brookfield Bloom bottles are recognized by both organizations.
Why measure texture?Consumer products succeed in the marketplace in part because their “textural characteristics” are pleasing to customers. This is certainly true with food products but it also applies to cosmetics, pharmaceuticals, packaging, industrial materials and even adhesive type materials.
Why Choose Brookfield?Brookfield Engineering is recognized around the world as offering high quality measurement instruments at an affordable price. Unsurpassed customer support is but one more reason to choose a Brookfield product when you are considering a viscometer, rheometer, texture analyzer or a powder flow tester.
The Brookfield Texture Department can also provide customers with complete texture assessment service. We specialize in the development of novel and innovative test applications and accessories for solid and semi-solid materials, enabling our customers to maximize the practical value of their texture studies within all test environments.
The CT3 Texture Analyzer utilizes uni-axial compression and tension forces in combination with a selection from our list of probes, grips and fixtures to test a wide variety of food, personal care products and industrial materials. Most tests desire to imitate conditions imposed on these products during manufacture, handling, and consumption or use. Characterizing the physical properties of your products in such an analytical manner provides “real life” insight and can be invaluable toward maintaining consistent, high quality manufacturing while minimizing cost.
Brookfield’s compact design of the CT3 has a long heritage of more than 20 years dating from the Stevens gelatin bloom tester. The CT3 still contains the Bloom test method and we offer the complete gelatin bath preparation system along with industry approved Bloom bottles.
ApplicationsQuality Control, Product Development and R & D
Ripeness Fracture ForceYield Point ElasticitySpreadability HardnessTackiness Cohesiveness Consistency Burst Strength Relaxation Breaking PointPliability Gel StrengthAdhesiveness Apparent ModulusChewiness Gumminess
Properties Measured
FoodDairy Yogurt Butter Cheese
Bakery Dough Bread Pastry
Snack Foods Chips Granola Bars Confections
Meat Beef Poultry Seafood
Fruit and vegetables
CosmeticsLipstickMascaraPowdercompactsEye liner pencils Creams Soap bars
PharmaceuticalsGelatins
Tablet hardness
Ointment
Adhesive dressing
MaterialsPackaging
Adhesives
Caulking
Rubber
Grease
Wax
52 T: 800.628.8139 or 508.946.6200 F: 508.946.6262 www.brookfieldengineering.com
BROOKFIELD TEXTURE ANALYZER
CT3™ Texture Analyzer compression and tension testing for rapid QC analysis
Standard Test ModesNormal Test:a single compression cycleHold Time Test:compress and holdCycle Count Test: compress multiple timesBloom Test:gelatin bloom strength testTPA Test:texture profile analysisTension Test:tensile testingStatic Load Test:calibration check
Tension Modeprovides tensile testing capability
Increased Probe Travel Distance with more space for larger samples
An extensive history and customer input have contributed
to the development of the most powerful, low cost, stand-alone
Texture Analyzer ever produced. With six test modes (plus
calibration check) and a wide choice of accessories, no other
texture analyzer has ever done so much without a computer
and software!
Choice of Base Tablesallows for larger samples and
more accessory choices
Easy-to-Use Intuitive Controls
Rotary Base Table
Fixture Base Table
Additional Load CellsSeven measurement ranges up to 50kg
Easy-to-Read Backlit Display
Texture Loader software allows adding up to ten custom tests to suit your everyday applications
Texture Loader
USB Computer Interface
TA-BT-KIT
TA-RT-KIT
53
ALL CT3 MODEL SPECIFICATIONS0-100g/0.01g0-1000g/0.10g0-1500g/0.20g0-4500g/0.50g1-10000g/1.0g1-25000g/2.0g2-50000g/5.0g
CT3-100CT3-1000CT3-1500CT3-4500CT3-10kgCT3-25kgCT3-50kg
MODELLoad Range/Resolution*
g = grams kg = kilograms
*Accuracy = ±0.5% Full Scale Range (FSR) mm = millimeter s = seconds
0.01-0.1mm/s (increments 0.01mm/s)
0.1 - 10mm/s (increments 0.1mm/s)
±0.1% of setpoint
0-100mm0.01mm0.1mm
Speed: Range
AccuracyPosition: Range Resolution Accuracy
Cylinder Probe
Junior Punch Accessory
Adjustable Vice Jig Small ScaleShear Blade
TexturePro CT SoftwareOptionalCollect data and perform detailed data analysis with real-time graphic plotting.
Easily create custom reports and graphs right from the menu screen.• Sample identifi cation set-up screen helps new operators quickly get started; test fi elds outline a variety of parameters• Intuitive set up for test methods and database fi le structures in a single window• Data is captured as a graph and stored in tabular database format• Advanced data analysis with built-in parameter calculations such as springiness, chewiness, hardness and much more!
What’s Included?Instrument with choice of load cell
NEW Texture Loader Software
USB Cable
Optional AccessoriesThe CT3 has a wide variety of probes, fi xtures and jigs which enable it to be very versatile. Brookfi eld can also custom design a fi xture and probe for most applications.
Choice of Base Table
TexturePro CT Software TA-CT-PAD-AY
Gelatin Bath System for sample conditioning
Bloom Jar - industry approved TA-GBB-2
Temperature Probe DVP-94Y
Bubble Level TA-LVL
Calibration Weight Set
The probes and fi xtures shown here are just a small selection from our optional accessories. Brookfi eld can develop custom equipment to meet most any texture measurement application.
Ottawa Cell
AOAC Probe (Bloom Gel Test)
Snap Test Jig Dual Grip Assembly
Extrusion Cell
T: 800.628.8139 or 508.946.6200 F: 508.946.6262 www.brookfieldengineering.com
CT3 Texture Analyzer Accessories, Probes, Fixtures and Jigs
BROOKFIELD TEXTURE ANALYZERS
ACCESSORIES FOR ROTARY BASE TABLE
TA-RT-KIT ROTARYBASETABLERound base table provides quick and easy height adjustment to accommodate various samples. Acces-sories listed below are mounted onto this table to fa-cilitate special sample holding requirements. Includes pair of T-bolts for securing table.
The following are accessories are for use with the rotary base table: TA-ATT ADHESIVETACKTESTER
Small scale assembly for testing adhesive strength TA-AVJ ADJUSTABLEVICEJIG
Small scale assembly for sample positioning TA-BEC BACKEXTRUSIONCELL
Small scale back extrusion testing consisting of 3 containers with internal dimensions of 38.1mm di-ameter, 24mm deep; includes one 25.4mm diameter probe
TA-JTPB JUNIORTHREEPOINTBENDASSEMBLY
Small scale three point bend assembly for fracture test of brittle materials. Probe used with this accy, TA7 Knife Edge Blade, is included in General Probe Kit TA-P-KIT2. Otherwise, please order TA7 sepa-rately.
TA-JPA JUNIORPUNCHASSEMBLY
Small scale accessory for controlled puncture testing of solid materials. Probe used with this accy, TA10, is included in General Probe Kit TA-P-KIT2. Other-wise, order TA10 separately.
Rotary Base Table
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
Fixture Base Table
Accessories, Probes, Fixtures and Jigs
TA-RT-5 T-BOLTS(2)
TA-RT-3 THUMBNUT(2)
T-bolts - used for securing base tables and grips to instrument base.
ACCESSORIES FOR FIXTURE BASE TABLE
TA-BT-KIT FIXTUREBASETABLERectangular base table with removable insert which is used as a test surface. With insert removed, all below accessories mount onto this table. Pair of T-bolts for securing table are included.
The following are accessories for use with the fixture base table: TA-CJ CONFECTIONERYJIG
Simple support jig used to permit the accu-rate positioning of irregular shaped samples beneath the travelling beam. Requires Fixture Base Table TA-BT-KIT
TA-DE DOUGHEXTENSIBILITYJIG
Comprising of 2 aluminium plates - 1 with 25.4mm hole and 1 with 38.1mm hole com-plete with upper fixing plates to hold del of sample. For use with TA18* and TA43* probes respectively. Requires Fixture Base Table TA-BT-KIT
TA-DEC DUALEXTRUSIONCELLFORBOTH BACKANDFORWARDEXTRUSION
Allows back extrusion and forward extrusion. Cylindrical cell 40mm diameter and 50mm in depth. Forces a semi-solid sample through an outlet of known geometry. Complete with 4 plungers of 34mm, 36mm, 38mm and 39.9mm in diameter and interchangeable base plates with apertures of 8mm, 6mm, 4mm, 2mm and one blank. Requires Fixture Base Table TA-BT-KIT
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
Accessories, Probes, Fixtures and Jigs
TA-DGA DUALGRIPASSEMBLY
These are multipurpose general jigs for ten-sile type testing. The fixtures utilize a univer-sal fitting enabling 360º rotation for compre-hensive test configuration. The 25mm wide grips are fitted with rubber inserts to maxi-mise contact adhesion with sample and are capable of holding rectangular samples up to 5mm thick. Each grip clamps from both sides of sample with two opposing thumbscrews.
TA-DSJ DOUGHSTICKINESSJIG
Special sample fixture for assessing the stick-iness of uncooked bakery dough. Requires Std Base Table TA-BT-KIT and TA3/1000 or TA11/1000* Probe.
TA-FMBRA FMBRADOUGHPOTSET
Standard accessory used in the preparation of dough samples prior to textural assessment. The set comprises of two test cells and two plungers: An aeration plunger and a compact-ing plunger. A known weight of sample is placed in the pot and the aeration plunger is used to remove air pockets through gentle rotation. The dough is then assessed for firmness using a 6mm in diameter stainless steel probe. Includes Dough Aerator, Dough Compactor & 2 Containers.
TA-JMPA JUNIORMULTIPLEPROBEASSEM-BLY
Small scale multiple probe assembly consist-ing of nine 2mm probes and corresponding base plate specifically designed to hold small samples of irregular geometry. Requires Fix-ture Base Table TA-BT-KIT
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
Accessories, Probes, Fixtures and Jigs
TA-OC OTTAWACELLThe Ottawa cell follows principles of the Ottawa Test Measurement System (OTMS). An acrylic fronted test cell and correspond-ing plunger are used to compress and extrude samples. Test samples are extruded by the travelling plunger. Complete With 3 Plates and 2 Plungers for forward and back extru-sion. Requires Fixture Base Table TA-BT-KIT
TA-VBJ VOLODKEVITCHBITEJAWS
Compression test used to simulate the shear-ing action of the front incisors as they bite through a food item, generating an indication of sample toughness or fibrousness. Consist-ing of both upper and lower jaws, the com-pressive movement of the travelling beam imitates the human “biting action”. Requires Fixture Base Table TA-BT-KIT
TA-WSP WIRESHEARPLATE
Aluminium plate with aperture to pass wire cutting blade through for shear type testing. Used with TA 53 cutting wire. Requires Fix-ture Base Table TA-BT-KIT
TA-SB SETOF4SHEARBLADES
Including Warner Bratzler test jig complete with slotted base. The blade set includes four shear blades, firmly held within a specially designed blade holder. The jig is utilized in the measurement of shearing and cutting forces, as the blades pass through a sample. Requires Fixture Base Table TA-BT-KIT
TA-CTP COMPRESSIONTOPPLATERectangular plate 150mm X 100mm, used for compressing large samples. Fixture Base Table TA-BT-KIT is normally used to support sample while testing with this large compres-sion plate.
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
Accessories, Probes, Fixtures and Jigs
T-BOLTSTA-RT-5 T-BOLT(2)
TA-RT-3 THUMBNUT(2)
SELECTED PROBE KITS
TA-P-KIT2 RECOMMENDEDGENERALPROBEKIT
Includes the following probes: 60 degree cone TA2/1000; 12.7mm cylindrical (BS std) TA5; 60mm wide knife edge TA7; 1.0mm dia needle TA9; 12.7mm cylindrical (AACC std) TA10; 25.4mm cylindrical (AOAC std) TA11/1000; 45 degree cone TA15/1000; 30 degree cone TA17; 12.7mm ball TA18; 50.8mm cylinder TA25/1000; 0.33mm cut-ting wire TA26; 2mm rod TA39; 38.1mm cylinder TA4/1000; 6mm cylindrical TA41; 25.4mm ball TA43; 4mm cylinder TA44 and TA-PCC
TA-P-KIT3 CURDPROBEKIT
Includes the following probes: 5mm disc TA46; 8mm disc TA-47; 10mm disc TA48 and storage case.
CYLINDER / ROD PROBES * included in TA-P-KIT2 TA3/100 25.4mmDIAMETERCYLINDERPROBE
Clear Acrylic. 35mm Long. Rad .35 - .43mm (Low mass for CT3100)
TA3/1000 25.4mmDIAMETERCYLINDERPROBE
Clear Acrylic. 35mm Long. Rad .35 - .43mm.
TA4/100 38.1mmDIAMETERCYLINDERPROBE
Clear Acrylic. 20mm Long. Rad .35 - .43mm. (Low mass for CT3100)
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
TA4/1000*38.1mmDIAMETERCYLINDERPROBEClear Acrylic 26g. 20mm Long. Rad .35 - .43mm.
TA5*12.7mmDIAMETERCYLINDERPROBE
Black Delrin 5g. 35mm Long. Rad .35 - .43mm.
TA6 6.35mmDIAMETERCYLINDERPROBE
Black Delrin. 20mm Long. Rad .35 - .43mm. . (Low mass for CT3100)
TA10*12.7mmCYLINDERPROBE
Clear Acrylic 5g. 35mm length with sharp edge. Gelatin Bloom Probe
TA11/100 25.4mmAOACSTANDARDCYLINDERPROBE
Clear Acrylic. 35mm Long. (Low mass for CT3100)
TA11/1000*25.4mmAOACSTANDARDCYLINDERPROBE
Clear Acrylic 21g. 35mm Long. TA19 1cm²KOBETESTPROBE
Stainless Steel. 11.3mm Diameter. 25mm Long.
TA24 4mmDIAMETERRODPROBE
Black Delrin. 20mm Long, Flat End TA25/1000*50.8mmDIAMETERCYLINDERPROBE
Clear Acrylic 23g. 20mm Long. Rad .35 - .43mm.
TA35 5mmDIAMETERCYLINDERPROBE
Black Delrin. 20mm Long. TA36 7mmDIAMETERCYLINDERPROBE
Stainless Steel. 35mm Long. TA39*2mmDIAMETERRODPROBE
Stainless Steel 5g. 20mm Long. Flat End (Margarine).
Accessories, Probes, Fixtures and Jigs
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
TA40 4.5mmDIAMETERRODPROBE Stainless Steel. 20.5mm Long. Flat End (Margarine). TA41*6mmDIAMETERCYLINDERPROBE
Stainless Steel 7g. 35mm Long. TA42 3mmDIAMETERCYLINDERPROBE
Stainless Steel. 35.8mm Long. TA44*4mmDIAMETERCYLINDERPROBE
Stainless Steel 10g. TA45 1mmDIAMETERCYLINDERPROBE
Stainless Steel.
CONICAL PROBES * included in TA-P-KIT2 TA2/100 60ºCONEPROBE
Clear Acrylic. 30mm Diameter. (Low mass for CT3100)
TA2/1000* 60ºCONEPROBE
Clear Acrylic 15g. 30mm Diameter, 36mm L TA15/100 45ºCONEPROBE
Clear Acrylic. 30mm Diameter. (Low mass for CT3100)
TA15/1000* 45ºCONEPROBE
Clear Acrylic 13g. 30mm Diameter, 40mm L TA16 40ºCONEPROBE
Clear Acrylic. 29mm Diameter 41mm L TA17*30ºCONEPROBE
Clear Acrylic 8g. 24mm Diameter, 46mm L TA27 20ºCONEPROBE
Clear Acrylic. 12.4mm Diameter.
Accessories, Probes, Fixtures and Jigs
TA29 15ºCONEPROBEStainless Steel. 8mm Diameter.
TA32/100 90ºCONEPROBE
Clear Acrylic. 30mm Diameter. (Low mass for CT3100)
TA32/1000 90ºCONEPROBE
Clear Acrylic. 30mm Diameter. TA-PCC PROBECARRYINGCASE
For Texture Analyzer Probes And/Or Calibra-tion Weights. (Foam Insert Cut To Or-der). Black Polypropylene - 225mm(L)X 200mm(W) X 70mm(H).
SPHERICAL PROBES* included in TA-P-KIT2 TA8 6.35mmDIAMETERBALLPROBE
Stainless Steel. TA18*12.7mmBALLPROBE
Stainless Steel 30g TA28 2mmDIAMETERBALLPROBE
Stainless Steel. TA31 1mmDIAMETERBALLPROBE
Stainless Steel. TA33 3mmDIAMETERBALLPROBE
Stainless Steel. TA38 10mmDIAMETERBALLPROBE
Stainless Steel. TA43*25.4mmDIAMETERBALLPROBE
Nylon 14g TA50 5mmDIAMETERBALLPROBE
Surimi application
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
Accessories, Probes, Fixtures and Jigs
MISCELLANEOUS PROBES * included in TA-P-KIT2 ** included in TA-P-KIT3
TA-DGA DUALGRIPASSEMBLYThese are multipurpose general grips for tensile type testing. The 25mm wide grips are fitted with rubber inserts to maximise con-tact adhesion with sample and are capable of holding rectangular samples up to 5mm thick. Each grip clamps from both sides of sample with two opposing thumbscrews for precise alignment. Includes one pair of T-Bolts for mounting to base. Base table kits are NOT USED with this fixture.
TA7*KNIFEEDGEClear Acrylic 8g. 60mm Wide.
TA9*NEEDLEPROBE
Stainless Steel. 1.0mm Diameter. 43mm Long. 10º Maximum Taper.
TA22 18SWGBARFRAMEPROBE
Aluminium Frame. 39mm Wide.1.2mm Dia TA23 12.7mmDIAMETERROUNDENDPROBE
Black Delrin. 35mm Long. TA26*0.33mmDIAMETERCUTTINGWIREPROBE
Aluminium Frame 67g, 40mm Wide, Con-nects to M3 Male Thread
TA46**TACURDPROBE5mm
Stainless Steel, 5mm dia disc ( 0.2 sq cm ) TA47**TACURDPROBE8mm
Stainless Steel, 8mm dia disc ( 0.5 sq cm ) TA48**TACURDPROBE10mm
Stainless Steel, 10mm dia disc ( 0.8 sq cm )
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
Accessories, Probes, Fixtures and Jigs
TA37 2.36mmdiametercuttingwireprobe Aluminium Frame. 40mm Wide. TA49 25.4mmDIAMETERROUNDEND
Clear Acrylic. LFRATrain LFRAOn-SiteInstallationandTraining
one day on-site time CT3Train CT3On-SiteInstallationandTraining
one day on-site time TA52 SmallScaleMOHRSShearBlade
Includes one blade holder and five blades. Blades are 9mm Wide x 35mm Length x .5mm Thick
TA53 .33mm Dia Cutting Wire Probe Aluminum Frame, 40 mm Wide, Connects to M6 Female Thread
CALIBRATION ACCESSORIES TA-CW-100C CALIBRATIONWEIGHTSET,100g WITHCASE&CERTIFICATE
Set of weights (total mass 100g) to be used to check calibration of the 100g LFRA Texture Analyzer. Includes verification certificate traceable to NIST standards.
TA-CW-1000C CALIBRATIONWEIGHTSET,1000g WITHCASE&CERTIFICATE
Set of weights (total mass 1000g) to be used to check calibration of the 1000g LFRA Tex-ture Analyzer. Includes verification certificate traceable to NIST standards.
TA-CW-1500C CALIBRATIONWEIGHTSET,1500g WITHCASE&CERTIFICATE
Set of weights (total mass 1500g) to be used to check calibration of the 1500g CT3 Tex-ture Analyzer. Includes verification certificate traceable to NIST standards.
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
Accessories, Probes, Fixtures and Jigs
TA-CW-4500C CALIBRATIONWEIGHTSET,4500gWITHCASE&CERTIFICATE
Set of weights (total mass 4500g) to be used to check calibration of the 4500g CT3 Tex-ture Analyzer. Includes verification certificate traceable to NIST standards.
TA-CW-10KGCCALIBRATIONWEIGHTSET,10kgWITHCASE&CERTIFICATE
Set of weights (total mass 10kg) to be used to check calibration of the 10kg CT3 Texture Analyzer. Includes verification certificate traceable to NIST standards.
TIA-8013 HANGERMOUNTINGRING
Used to hang calibration weights. Included with each weight set. Replacements may be ordered with this number.
CCSCT3 Calibration & Certification Service for CT3
GELATIN ACCESSORIES
TA-GBB-2 BROOKFIELDGELATINBLOOMBOTTLEKIT(12pcs)
One dozen Brookfield gelatin bloom sample bottles w/BEL logo bottle holds 120ml vol-ume and includes TA-SBS stoppers
GelatinPreparationBathSystem
TC-402D(qty2)TC-351D(qty1)
System is used by attaching TC-351 to one TC-402D bath set to 10C. Second TC-402D bath is set to 60C providing rapid transfer between the thermal environments necessary for conditioning gelatin for Bloom testing. Each bath has 29L reservoir and capacity for twelve (12) gelatin jars and a removable rack for easy handling. 21L of water is required for proper fluid level with rack and 12 bloom jars.
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
Accessories, Probes, Fixtures and Jigs
TA-SB BROOKFIELDSAMPLEBOTTLES(6pcs)
Alternative sample bottle similar to TA-BSB. Order stoppers TA-SBS separately
TA-SBS BROOKFIELDRUBBERSTOPPERS(12pcs)
Rubber stoppers for TA-SB (Brookfield Sample Bottles)
CT3-CS-100 BLOOMTESTSTRIPFor use with 100g CT3 Texture Analyzer to check load calibration.
CT3-CS-1000 BLOOMTESTSTRIP
For use with 1000g & 1500g CT3 Texture Analyzer to check load calibration.
Don't see what you need? Brookfield can design fixtures, probes and jigs to hold products of all shapes and sizes and to perform a variety of texture tests. Please call to discuss your application.
Accessories, Probes, Fixtures and Jigs
Brookfield Engineering Laboratories, Inc. 11 Commerce Boulevard Middleboro, MA 02346-1031 USAT: 800.628.8139 or 508.946.6200 F: 508.946.6262 W: www.brookfieldengineering.com
Recommended