View
0
Download
0
Category
Preview:
Citation preview
A B1 B2 C1 C2 D E
G H I J KF L
Hardware Supplied
Phillips & Flathead screwdrivers and hammer required
30mmscrew x20
12mmscrew x16
bolt & nut set x32
14mmscrew x56
18mmscrew x8
50mmscrew x16
dowelx24
hingex4
wedgex8
*We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use.Please clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%.
washer x2
bracketx2
stopperx2
feetx4
sliderail x3
WARNING: Any furniture that is not anchored to a wall has the potential to tip over in certain circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake. Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device provided should fit most wall types, but please note that different wall materials may require different fixing devices from those supplied.
For quicker assembly, we recommend the use of a power drill on a low-speed setting.
M
12mmscrew x2
N
bracketx4
O P Q R
25mmscrew x2
14mmscrew x2
wall plug x2
wall strap x2
Wall Strap
Vigo Buffet
1mocka.co.nz | mocka.com.au
Assembly InstructionsThank you for your purchase. Please follow the instructions below for correct assembly.
1 2
Insert 4x feet (I) into the leg side panels as shown. Attach the leg panels together as shown using 8x 30mm screws (B1). Tighten with a screwdriver.
I
I I
I
B1
B1
B1
B1
B1
B1
B1
B1
Vigo Buffet
2mocka.co.nz | mocka.com.au
Assembly Instructions
3 4
Attach 4x brackets (N) into the corners of the legs and secure using 16x 12mm screws (B2). Tighten with a screwdriver.
Attach 3x slide rails (E1) to panel [5] using 6x 14mm screws (C1). Attach 3x slide rails (E3) to panel [6] using 6x 14mm screws (C1). Tighten with a screwdriver.
B2
N
E3
E1
E1
E1
65
E3
E3
C1
C1
Vigo Buffet
3mocka.co.nz | mocka.com.au
Assembly Instructions
5 6
Insert 4x bolts (A) into panels [5] and [6]. Attach 1x bracket (L) to panel [5] and secure with 4x 14mm screws (C1). Attach 1x bracket (L) to panel [6] and secure with 4x 14mm screws (C1). Tighten with a screwdriver.
Attach panels [5] and [6] to panel [2] using 4x dowels (F) and 4x 50mm screws (D). Tighten with a screwdriver.
2
C1
L
C1
65
65
D
F
F
F
F
D
D
DA
A
A
A 2
Vigo BuffetAssembly Instructions
4mocka.co.nz | mocka.com.au
Jolt WardrobeASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
7 8
Attach panel [7] to panel [5] using 2x dowels (F) and 2x locking nuts (A) as shown. Attach panel [7] to panel [6] using 2x dowels (F) and 2x locking nuts (A) as shown.Tighten with a screwdriver.
Insert 4x bolts (A) into panel [3] and panel [4].
7
65
43
7
A
F F
F A
A
A
A
A
A
A
A
A
A
3
Vigo BuffetAssembly Instructions
5mocka.co.nz | mocka.com.au
9 10
Slide panel [8] down along the grooves between panels [3] and [4]. Attach 2x stoppers (K) to the brackets (L) as shown.
K
8
L
4
37
4
3
7
F
F
F F
FF
A
A
A
A
Attach panel [3] to panel [7] using 4x dowels (F) and 4x locking nuts (A). Attach panel [4] to panel [7] using 4x dowels (F) and 4x locking nuts (A). Tighten with a screwdriver.
Vigo BuffetAssembly Instructions
6mocka.co.nz | mocka.com.au
11 12
Insert 8x bolts (A) to panel [1].
A
1
FF
F
F
F
F AF
F
65
4
3
1
A
AA
A
AA
A
A
Attach panel [1] to panels [3], [5], [6] and [4] using 8x dowels (F) and secure with 8x locking nuts (A). Tighten with a screwdriver.
A
A
A
A
A
A
A
Vigo BuffetAssembly Instructions
7mocka.co.nz | mocka.com.au
13 14
Attach 8x wedges (H) to the sides of panel [8] as shown, and secure with 8x 18mm screws (C2). Tighten with a screwdriver.
Attach base panel [2] to the legs using 12x 20mm screws (B1). Tighten with a screwdriver.
C2
8
H
HH
H
HH
HH
H
B1B1 B1
B1
B1B1
B1B1
B1B1
B1
B1
2
Vigo BuffetAssembly Instructions
8mocka.co.nz | mocka.com.au
15 16
Attach 1x washer (J) to panel [9] and secure with 1x 12mm screw (M). Attach 1x washer (J) to panel [10] and secure with 1x 12mm screw (M). Tighten with a screwdriver.
Attach 4x hinges (G) to the unit as shown using 24x 14mm screws (C1). Tighten with a screwdriver.
109
M
J
M
J
3
10
9
C1 G
G
G
NOTE: If the doors are uneven or there is a gap in the middle, loosen
or tighten the screw on the door hinge until they are sitting flush.
Vigo BuffetAssembly Instructions
9mocka.co.nz | mocka.com.au
17 18
insert 4x bolts (A) into panel [11], then attach side panels [12] and [13] using 4x locking nuts (A). Slide panel [15] along the grooves between panels [12] and [13] to form the base.
Attach panel [14] as shown using 4x screws (D). Attach 1x slide rail (E2) to panel [12] and 1x slide rail (E4) to panel [14]. Secure with 4x 14mm screws (C1) and tighten with a screwdriver. Repeat Steps 15 and 16 to assemble the remaining two drawers.
14
Drawers x3
A
E
AA
A
AA
13
12
11
15
13
12
D
DD
13
12
C1
C1
C1
C1
E2
E4
Vigo Buffet
10mocka.co.nz | mocka.com.au
Assembly Instructions
D
19
Insert the completed drawers as shown, ensuring they slide smoothly and easily along the rails. Attach 2x safety straps (R) to the back side of the unit using 2x 25mm screws (P). Lift the furniture into the desired position, do not drag. Attach the other end of the safety straps to the wall using 2x wall plugs (Q) and 2x 25mm screws (O). Tighten with a screwdriver. You抮e done, enjoy!
1
11
11
11
R
O
Q
R
R
Vigo Buffet
11mocka.co.nz | mocka.com.au
Assembly Instructions
Recommended