Triangulation with the Disto Using 3 points Copyright © 2006 by Distagage.com, All Rights...

Triangulation with the Disto Using

3 points

The slides in this presentation will advance automatically. To manually advance/reverse the slides, use the navigation buttons

provided at the bottom of each slide

Click Here To Begin

Triangulation with the Disto Using 3 Points

Let’s look at a situation where we would like to determine the width (ft) of the front side of a house.

Let’s call it “X”

To determine “X,” we will use the “3-point Triangulation” method; also referred to as the “3-point Indirect Measurement” method.

First, we call this a “3-point” measurement because it involves measuring to 3 distinct points.

Point 1

Point 2Point 1

Point 1 Point 2 Point 3

Turn the Disto on

Turn the Disto on … and press 2 times ….

Turn the Disto on … and press 2 times …. to enter the 3-point mode.

Notice the blinking line.

Notice the blinking line. The Disto is now ready for the 1st measurement.

Now, step back from the house ….

Now, step back from the house …. to a distance that will allow you to clearly see both corners of the front side of the house ….

The goal is to position the Disto somewhere within the middle section of the object being measured …

AND … create a right angle with the front side of the house.

Rotate the Disto to the left …

Rotate the Disto to the left … and point the laser dot at the leftmost edge of the front side of the house.

Press the DIST key.

Notice that the 1st measurement appears on the screen …

And … a blinking line indicates that the Disto is ready for the 2nd measurement.

Rotate the Disto so that it creates a RIGHT ANGLE with the front side of the house …

Rotate the Disto so that it creates a RIGHT ANGLE with the front side of the house … and press the DIST key.

The distance for the 2nd measurement appears on the screen …

And … a blinking line indicates that the Disto is ready for the 3rd measurement.

To obtain the 3rd measurement, rotate the Disto to the right …

And … point the laser dot at the rightmost edge of the front side of the house.

Press the DIST key.

The distance for the 3rd measurement appears on the screen …

AND … the resulting measurement for “X” appears on the main line of the display.

55 ‘

Important: Make sure all three measurements are taken at the same relative position …

AND … rotate the Disto about a solid, stationary REFERENCE POINT.

To increase accuracy, consider using the “continuous measurement” function for the 2nd (middle) measurement.

The purpose of the continuous measurement function is to find the shortest (perpendicular) distance to the front side of the house.

To use the continuous measurement function, simply press AND HOLD DOWN the DIST key for the 2nd (middle) measurement.

There will be a slight delay and the Disto will begin to beep rapidly.

Let up on the DIST key.

Point the Disto in a direction that appears to be perpendicular to the front side of the house …

Point the Disto in a direction that appears to be perpendicular to the front side of the house … AND …

… while the Disto records continuous measurements, point the Disto slightly to the left and right of the perpendicular line.

Continue until you are certain the perpendicular distance has been recorded.

Then press the DIST key again (one time) to stop the continuous measurements.

The minimum (perpendicular) distance displays on the screen …

and … the Disto is now ready for the 3rd and final measurement.

The 3-point triangulation (or indirect measurement) function is available on the Disto A5, Disto A6 and Disto Plus models.

A5 A6Plus

The most significant feature that separates the Disto A5/A6 models from the Disto Plus model is the continuous measurement function.

A5 A6Plus

The Disto A5 and A6 models both incorporate the continuous measurement feature within all 3 measurements.

The Disto Plus only uses the continuous measurement feature for the middle (2nd) measurement..

The 3-point triangulation feature is available on some of the older Disto models such as the Disto Classic and Disto Pro series models.

A5 A6Plus

The procedures for using the triangulation feature with the older Disto models will differ slightly from the procedures provided in this demonstration.

A5 A6Plus

Click Here to Exit

Triangulation with the Disto Using 3 points Copyright © 2006 by Distagage.com, All Rights...

Documents

gostamos disto

Triangulation Group5

Zlekha Triangulation

Triangulation and Integration: processes, claims and ...epubs.surrey.ac.uk › 787219 › 1 › Triangulation and... · conceptualisations of ‘triangulation’. Outcomes: what triangulation

Leica DISTO

Triangulation Matrix

Final triangulation

TRIANGULATION AND TRILATERATION - الصفحات الشخصيةsite.iugaza.edu.ps/.../TRIANGULATION-AND-TRILATRATION.pdf · 2012-05-04 · TRIANGULATION AND TRILATERATION 1.1 GENERAL

Leica Disto 2012

Spec DISTO reveres011Laitz HLD60 Leica Disto D110 Leica Disto D210 Leica Disto X310 Leica Disto D5 Leica Disto D8 Leica Disto D510 Leica Disto D810 touch ช่วงการวัดระยะทางตั

Leica Disto D3

Delaunay triangulation of manifolds - 3. Triangulation of

A Distributed Triangulation Algorithm for Wireless Sensor ...h1wu/paper/triangulation-infocom11.pdf(l) Triangulation with k =3. (m) Triangulation under 10% distance errors. (n) Triangulation

Delauny Triangulation

TRIANGULATION - PERSILAusmpersila.weebly.com/uploads/1/7/6/5/17653075/triangulation.pdf · Triangulation – pronunciation ^traɪˌæŋgjʊˈleɪʃən _ Triangulation - meaning Often

Recove Disto

Image Morphing, triangulation - Penn Engineeringcse399b/Lectures/CSE... · Image Morphing, triangulation 2) Compute triangulation between the feature points a)Use Delaunay triangulation

Leica DISTO TM D3 - Leica Geosystemsptd.leica-geosystems.com/.../disto/DistoD3/manuals/User_Manual_D3… · The Leica DISTO™ is designed for use in areas perma- ... Leica DISTO™

Data Triangulation

Manual Disto D8