View
1
Download
0
Category
Preview:
Citation preview
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
DF 56 – The Highest Productive and Versatile Slitter, Cutter, Creaser, Perforator, and More all-in-one System
Computer Controlled
vacuum high pile feeder:
• 16” loading capacity is standard. 22” is optional.
• Hi-tech ADF™(anti double feeing) design makes double feeding virtually impossible
• No mark or scuff
Vacuum table sheet
registration table
Cross & Jump Perforation Module
• Up to 24 cross perforations in one sheet pass .
• Up to 12 jump perforations in one sheet per perf head
• Up to 6 jump perforation heads can be installed
Window’s based
control system
• Easy to use. • Optional remote
operating and remote tech service via internet
Cutting Module
• Up to 32 cuts in one sheet pass.
Creasing Mechanism
• Up to 24 creases in one sheet pass.
Slitting Modules
• Two slots for different combinations
• Software or manual adjusted positions
• One DF 56 can replace four stand alone machines. (slitter, cutter, creaser, and perforator)
• Slit, cut and crease up to 56 sheets per minute. Crease up to 120 sheets per minute
• Metal block design for long last and easy service
• Upgradable to DFF 56 easily(inline folder)• Multiple patents pending.
Proudly designed and
manufactured in the U.S.A.
The DF 56 slits, cuts, creases, jump perforates and cross perforates sheets up to 13” by 40” in one sheet pass. It can produce the
full range of business cards, greeting cards, post cards, wedding cards, flyers, photos, brochures, and more, both with and without
creases and perforations up to 400 GSM.
DF 56IFS
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
Proudly designed and
manufactured in the U.S.A.
Slit, Cut, Crease, Cross Perf and Jump Perf in One sheet Pass
DF 56 – The Highest Productive and high Versatile All-in-On
Typical example: from
one sheet pass, you will get
4-up full bleed folded cards
(from a 12” x 18” stock) with
“L” type tear-able perforations
Cross and
Jump Perf
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
“T” Perforated
“L” Perforated
Some Perf Examples
Standard jump perf head (lengthwise direction): 2Optional 3, or 4 or 5 or 6
Each jump perf head can do up to 12 perf segments in one sheet pass
Y (crosswise direction): up to 24 cross perf in one sheet pass
More Perf Examples
Manual
tear off
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
Some more examples of cards and documents
Slit, Cut, Crease, Cross Perf and Jump Perf in One sheet Pass
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
DF 56F 200 DFF 56+ =It takes less than a minute to upgrade DF 56 to DFF 56 . DF 56 and F 200 can work as two stand alone machines
Full bleed multi-row folding
Full bleed, folded
Remotely operate and tech service via internet (optional)
Some new benefits only from DF 32 (not any other OEM can provide)
DFF 56 DFF 56 Both DF56 and DFF 56
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
Gut Width “R”
Gut Width “L”
DF56 guarantees – the difference between gutter width “L” and “R” is less than 0.002” for entire 40” length sheet
DFG uses high precision gutter slit technology
DF 56 guarantees – There is no image shift (green on blue) for small or large card
DFG uses industry’s exclusive slitting and cutting technology
Sheets move direction
Good
Not Good
Some problems DF 56 solved (it is very difficult for high speed digital production)
Good Image Squareness
*DFG’s guarantees depends on materials
Sheets move direction
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
Quantum III Feeder™ - the most advanced vacuum belt, high pile top feeder (patent pending)
Quantum III Feeder™ - This AI (Artificial Intelligent) feeder uses high speed 32 bits embedded computer and high precision sensors to control all feeding process. It makes your job much easy.
Accept up to 8” sheets. (upgradable to 22”)• Sheet size from 8” x 8” to 13” x 21” (up to 40” with long sheet kit, from
5” x 5” with short sheet kit)• Sheet weight from 75 gsm to 450 gsm• Can feed up to 18,000 sheet per hour (11” sheet)
• No suck flow manual adjustment needed• No side blow (air knife) flow manual adjustment needed• No manual fence adjustment needed (gap between sheets and fence)• No manual table vacuum suck flow adjustment needed
Quantum III Feeder™ - This AI feeder
• Makes sheets double feeding physically virtually impossible and• No marking or scuffing (It uses anti static and dust free belt)• No or minimum feeding hesitation and it can be a• “Walk away” operation (No operator present needed when feeding)
This AI Feeder maintains top several sheets separated when needed
Feeding belt
The Quantum III Feeder™ will keep this gap at its best size by computer and sensors. (no manual adjustment needed)
Fence
Quantum III Feeder™ is a AI feeder
Quantum III Feeder™ uses an additional registration on exit vacuum
table of the feeder to maintain sheet squareness before getting feeding rollers. (there were lots of complains of sheet squareness from belt type high speed thick sheets feeding. Quantum III Feder™ got it solved)
• It compensates the sheet width
error from sheet manufacturer.
• It also compensates sheet
width shrink or expansion
An additional registration
Negative air pressure to assist sheets squareness
Due to continuous product improvement, specifications and other tech info are subject to change without notice.. Feeding quality is material dependent
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
Standard 16” capacity advanced
vacuum pile feeder (optional 22”
Quantum II™ feeder is available )
This patent pending feeding technology
virtually eliminates double feeding. The
table always moves up or down or stays
at its optimal position during each
feeding cycle. It also eliminates marking
and scuffing.
Vacuum table sheet registration
system
Interchangeable Cross Perf Module
Interchangeable Jump Perf Module
CutterModule
CreaseMechanism
Interchangeable Slit Modules
Slitter Modules
Position adjusted by software or manually. This
interchangeable module design makes the machine more
versatile and significantly reduces both operational cost
and machine down time. Patent Pending. Score modules
are optional
Cutter Module
Premium hardened US-produced tool steel to ensure a
longer life and low cost reshaping. Fully automatic
cutting force control, based on paper weight gsm and
width. (by software)
Creaser
Comes with a 10 year warranty. The soft touch
technology based matrix design results in a superior
quality of creasing. Fully automatic crease depth
control, based on paper weight gsm. (by software)
Jump Perf Module
Standard is two perf head. Optional up to 6 perf
head. It can makes up to 72 perf line segment for
one sheet pass
Cross Perf Module
You can do up to 24 cross perforations in one
sheet pass. A optional negative crease module can
be installed at this position.
This high tech F200 fold is
a direct response to the
need for a faster folder to
keep up with the demands
of today's market while
retaining high accuracy and
repeatability. The F 100 can
make more than 10,000
folded cards per hour. It can
handle a wide variety of
paper sizes and thicknesses,
with a maximum size and
thickness of 14.5” and 400
gsm.
F100
two stage knife fold
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
• It take less than a minute to change
• The perf force, speed, travel are all controlled by software.
• You can change it to Negative Creasing Modules too.
Interchangeable Cross Perforation Module.
• It take less than a minute to change
• You can change it to score modules
Interchangeable Jump Perforation Module.
Interchangeable Margin Slit Module.
Interchangeable Center Slit Module.
• It take less than a minute to change
• Slit position are adjusted by software for 1 or 2 or 4 pairs slitting blades. You can also change them manually
• For more than 4 pairs of blades, slit position are adjustment manually (Max. 12 pairs)
• You can also change it to score module
• It take less than a minute to change
• Slit position are adjusted by software for 1 or 2 or 4 pairs slitting blades. You can also change them manually
• For more than 4 pairs of blades, slit position are adjustment manually (Max. 12 pairs)
• You can also change it to score module
Some Interchangeable Modules
New Picture come soon
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
Speed: SCC up to 56 sheets per minute (2 cuts and 1 crease on 11” sheet) . Crease up to 120 sheets per minute (11” center crease).
Sheet size: 8” x 8” to 13” x 19”`(40” with optional long sheet kit)Minimum finished size: 1” x 2” (cut and creaser only)Minimum finished folded card:: 3.25” x 4”Sheet weight: 105 gsm to 400 gsm (perforation up to 300 gsm)Vacuum feeder loading capacity: 8” standard. 16 and 22” is optionalReceiving capacity: 6.5” for DF56. conveyor is optional# of jobs: unlimited job can stored and easy recalled from hard disk
Maximum cuts for one sheet pass: 32Maximum creases for one sheet pass: 24Maximum cross perf for one sheet pass:24Maximum jump perf for one sheet pass: 72 segmentsPower: Single phase. 115 V, 60 Hz, 6A or 230V, 50 Hz, 4AMachine size: 108” (L) x 30” (D) x 48” (H) Shipping Weight: 700 lbs.
Specifications*:
* Material dependent
High Productive and High Versatile
Digital Finishing
SystemDF 56IFS
Digital Finishing Group14050 Simone Dr., Shelby Twp., Michigan 48315 , U.S.A. Fax: 775-587-5352 Email: info@dfgus.com Website: www.ifinishingsystem.com
Digital Finishing GroupThe True Leader in Advanced Post-Printing Finishing
Due to continuous product improvement, specifications are subject to change without notice. The Data will change for different type of materials.. Duplo’s data is for reference only. Please contact www.duplousa.com for its latest machine speed and price info.
ACF Series – Creaser, perforation and
Knife Folders. World’s fastest at its class
– up to 9,000 sheets per hour
ACF 1500 / ACF 1200 / ACF 1100
C Series – Creasers
World’s fastest – up to 9,000 sheets
per hour
C1500 / C1200 / C1100 / C1000 / PC0
/ PC20 /PC10
IDF Series – Directly connect to a
printing press. Inline card slit, cut,
crease, and fold all in one. World’s first
and only
You might also interest:
SCCF Series – Slit, cut, crease, fold and moreSCC Series – Slit, cut, crease and moreSCCF 65 / SCCF 40 / SCC 65 / SCC40
DFF series – Slit, Cut, Crease, two dimensional perforation and Knife Fold and more. World’s fastest and most versatile – DFF 75 / DFF 32
World’s first and only
DF series – Slit, Cut, Crease, two dimensional perforation and more. World’s fastest and most versatile – DF 75 / DF 32
Recommended