View
1
Download
0
Category
Preview:
Citation preview
“ The Don Bosco Technical
High School Programs aims
to develop fundamental
Knowledge, Attitude, Skills
and Habit which would
prepare the students future
studies in Engineering and
other Technology fields. To
accept the demands of
Collegiate life through
sufficient Technical
preparations and their
intelligent application in
appropriate life situation.”
Learning Areas
Number of
Hrs. / Week
Unit
Equivalent
1st Yr. 2nd Yr.
Automotive-Mechanical
Technology (AT/MT)
2 2 1
Electro-Electrical
Technology (ET/ELX)
2 2 1
Computer Technology 2 2 1
Industrial Drafting Technology 2 2 1
Total Time Allotment 8 Hrs 8 Hrs. 4 Units
By the end of the 2nd year
level, the students are
evaluated for specialization in
6 Technologies for 3rd and 4th
year levels.
The evaluation for
specialization is based on:
Aptitude Test – 40%
Technical Grades (1st
and 2nd Years) – 40%
Shop Preference - 20 %
SHOP AR MA NA SR
AUTOMOTIVE 30% 40% 15% 15%
MECHANICAL 15% 40% 30% 15%
ELECTRONICS 40% 10% 40% 10%
ELECTRICITY 30% 15% 40% 15%
INDUSTRIAL DRAFTING 35% 10% 20% 35%
COMPUTER 40% 10% 20% 30%
AR - Abstract Reasoning NA - Numerical Ability
MA - Mechanical Ability SR - Space Relations
Learning Areas Number
of Hrs. /
Week
Unit
Equivalent
3rd
Yr.
4th
Yr.
Automotive Technology
• Technology
• Shopwork
• CAD (Computer
Aided Design)
2
6
1
2
6
1
1.5
2.0
0.5
Mechanical Technology
• Technology
• Shopwork
• CAD
2
6
1
2
6
1
1.5
2.0
0.5
Computer Technology
• Technology
• Shopwork
• CAD
2
6
1
2
6
1
1.5
2.0
0.5
Learning Areas Number
of Hrs. /
Week
Unit
Equival
ent
3rd
Yr.
4th
Yr.
Electrical Technology
• Technology
• Shopwork
• CAD
3
5
1
3
5
1
1.5
2.0
0.5
Electronics Technology
• Technology
• Shopwork
• CAD
3
5
1
3
5
1
1.5
2.0
0.5
Industrial
DraftingTechnology
• Technology
• Shopwork
• CAD
2
5
2
2
5
2
1.5
2.0
0.5
FIRST YEAR
- Application of different measuring
tools, hand tools and light power
tools through experiments and light
metal works.
SECOND YEAR
- Introduction to precision works as
applied in light metal works
- Mastery of linear measurements
- Application of measuring tools,
bench work tools, light power tools
and work holding devices in shop
activities.
THIRD YEAR
- Basic automobile servicing of a
gasoline engine and electrical
systems
- Trouble shooting and testing with
the use of manual and power tools
FOURTH YEAR
- Automobile servicing of a diesel
engine
- Trouble shooting, testing,
overhauling and assembling with
the use of servicing and testing
tools.
THIRD YEAR
- Precision measurements using Vernier , Micrometer calipers, Vernier height Gauge and Vernier Bevel Protractor
- Machine tools, machine principles, theories, operations and set -ups
FOURTH YEAR
- Mastery in using machine and precision measuring tools that are used in translating a creative design into a functional mechanical unit.
FIRST YEAR
- Different types of electrical/electronics hand tools, components, and concepts in basic electricity and electronics
Solving mathematical equations concerning Ohm’s Law and Power laws
Computing the parameters of series and parallel circuits
Multitester Assembly
SECOND YEAR
- Computation of parameters of different electrical circuits
- Translate schematic diagram to actual components
- PCB designing (Printed Circuit Board)
THIRD YEAR
- Interpret and assemble different basic
electronics circuits and operate
electronic precision measuring
instruments.
- Circuit Parameters of Series, Parallel
and Combination Circuits; Magnetism
and Electromagnetic.
- RLC Circuits
- Filter Circuits; Semiconductor
Principles; Semiconductor Diodes
and Transistors; Power Supply
Circuits.
- Transistor Biasing and Coupling;
Classes of Transistor Amplifier and
Power Amplifiers
FOURTH YEAR
- Design and construct electronic
communication system and test
communication circuit project and
phase control electronic
components.
- Sound and Audio, Amplifier
Circuits.
- Factors that affect the audio
amplifier circuits like distortions
and negative feedback, tone
control circuits and the parameters
of the amplifier circuits.
THIRD YEAR
- Electrical plan for a
residential consumer
- Basic residential wiring
FOURTH YEAR
- Transformers and single
phase motors
- Designing, constructing and
troubleshooting different
types of Industrial controls
FIRST YEAR
- Development of web
pages using basic HTML.
SECOND YEAR
- Web development and
animation using advanced
HTML and Javascript.
THIRD YEAR
- Web design and development
using Dreamweaver for web
pages, Fireworks for graphic
design and Flash for animation,
Programming using Access and
Visual Basic
FOURTH YEAR
- Computer networking, C++,
PHP/MySQL and Java.
FIRST YEAR
- Creating 2-dimensional drawing, color rendering, lettering and basic 3-dimansional drawing in pencil practice through proper measuring, scaling, correct usage and manipulation of drafting instruments
SECOND YEAR
- Advance 2-dimensional and 3-dimensional drawings in pencil and ink applications through proper scaling methods using the metric system of measurements
THIRD YEAR
- Basic commercial art, product
designing, fundamentals of
architectural designing, interior
perspective presentation and 3-
dimensional scaled modeling both in
manual and Computer Aided Design
applications (CAD).
FOURTH YEAR
- Basic architectural drafting designs,
interior, plumbing, electrical, structural
drawings and designs, pictorial
rendering both in manual and
Computer Aided Design applications
(CAD) as well as in translating the
said designs into a 3-dimensional
scaled models
FIRST YEAR & SECOND YEAR
SUBJECTS HOURS
ENGLISH 5
MATHEMATICS 5
SCIENCE 5
SOCIAL STUDIES 4
FILIPINO 3
CHRISTIAN LIVING 3
MUSIC 2
PHYSICAL EDUCATION 2
THIRD YEAR
SUBJECTS HOURS
CHEMISTRY 6
ENGLISH 5
GEOMETRY 5
PHYSICS 1 3
FILIPINO 3
ALGEBRA 3 3
WORLD HISTORY 3
CHRISTIAN LIVING 3
PE/MUSIC 2
RESEARCH 1 1
INFORMATION TECHNOLOGY 1
Recommended