Siplace Vision Training. What‘s new? New cameras: – RV12-head: Type 28 (old: 12) – RV6-head:...

Siplace Vision Training

What‘s new?

New cameras: – RV12-head: Type 28 (old: 12)– RV6-head: Type 29 (old: 13)– Twin-head: Type 33 (old 22)

– PCB-camera: Type 34

What‘s new?

Component-type:– Baredie– Chip– Melf– Moulded– ECV– SOT– DPack– SOxx

– QFP– SOJ– PLCC– BGA– CCGA

– Sockets– Connector– Shield– Nonstandard

What‘s new

New lead-types– Corner to describe shields

– Blob to describe leads of any shape: for example oval: or undefined shape:

What‘s new?

No ICOS-computer any more - Siplace Vision is an application running on station computer

old: new:

SCICOSvisioncomp

SCvision comp

SV-appl

What‘s new?

Component face-down recognit.

Pattern-fiducial:– it is now possible to teach any pattern on PCB as

a fiducial. For instance: corners of circuit pathes

Area used as ficucial

What‘s new?

Autosave of failed component measurements– By analysing the stored dumps you can see why

the components were rejected.

This is a really big help to find and avoid errors and lower reject rates.

How to program- Preparations in SiPro

Already existing GF:1. If not yet done set the correct type in SiPro.2. If not yet done add digital cameras.3. For standard components SV will use ICOS-GF-data => Do not mark checkbox

„Requires seperate group description“!!!4. Only mark checkbox for components that have leadtypes ICOS does not

know!For example: Shields (corners) or components you described with „blob“ leads.(Teach these components on the station before production!)

5. If possible / required check „Detect flipped Component“.6. If you get error messages during optimizing correct existing GFs according to

optimizer‘s messages. For example: Lead tolerance <50% of lead size

1

3

5

How to program- Preparations in SiPro

New standard GF:1. Enter the correct dimensions (X,Y,Z) to pick up

the component correctly.2. Set type to „Baredie“ – you dont have to

describe leads then.3. Teach the component on the station (and set the

correct type).

Do not check!

1

1

2

It is not necessary to create leads here!Leads will be created through Sipl. Visionby teaching the component on the station.

The Siplace Vision groups are disabledbecause Sipl. Vision will use ICOS groupsfor components with standard lead shapes(Gullwing, J-Bend, Wraparound, Ball)

How to program- Preparations in SiPro

New special GF (shield, sockets, „blobs“, …):– Describe the GF correctly for the ICOS system.– Set the type baredie.– Mark checkbox „Requires seperate group description“– Test the component on an ICOS machine.– Teach the component on an SV machine and set the

correct type.– By teaching on the machine the lead groups for SV will be

written to SiPro database.

With seperate group descriptions SVhas no effect on ICOS lead groups.So you have to describe them manually.

It is not necessary to create leads here!Leads will be created through Sipl. Visionby teaching the component on the station.

How to program on the station

General things– First make sure the dimensions and geometry are

correct– If the GF does not run with an exact geometrical

description adust illumination– Adjusting algorithms is the very last step and only

needed in rare exceptions!

How to program on the station

In case of an error scroll through the list of measuresteps and find the failing step.

Look at the filters. Is it the correct one? Are the dimensions of the filter correct?

How to program on the station

SO4 SO4 SO4

How to program on the station

SO4 SO4 SO4