SERIES ˆ 2˛ - API Delevan Electronic RF and Power ...API_newlayouts_single:APIcatalog_newlayouts...

Actual Size (Max.)

SERIES 2534R2534

Molded Unshielded RF Coils

SRF MINIM

UM (M

Hz)

DASH NUMBER*

INDUCTANCE (mH)

Q MINIM

UM

TEST FREQUENCY (kHz)

DC RESISTANCE

MAXIM

UM (OHM

S)

CURRENT RATING

MAXIM

UM (m

A)

TOLERANCE

Physical Parameters

Inches MillimetersHeight 0.345 Max. 8.76 Max.Diameter 0.25 ± 0.010 6.35 ± 0.25Lead SizeAWG #24 TCW 0.020 ± 0.0015 0.508 ± .0038Lead Length 1.62 ± 0.12 41.15 ± 3.05Lead Spacing 0.170 to 0.210 4.32 to 5.33

Current Rating at 90°C Ambient 35°C Rise

Operating Temperature Range –55°C to +125°C

Maximum Power Dissipation at 90°C 0.23 W

Weight Max. (Grams) 1.0

Core Material Ferrite

Marking Delevan cage code (99800); 2534; dash numberwith tolerance letter. Note: An R after 2534 indicates aRoHS component.

Example: 2534R-24K

99800 2534R -24K

Packaging Bulk only

Made in the U.S.A.

SERIES 2534 FERRITE CORE

-00K -02K -04K -06K -08K -10K -12K -14K -16K -18K -20K -22K -24K -26K -28K -30K -32K -34K -36K -38K -40K -42K -44K -46K -48K -50L -52L -54L -56L -58L -60L -62L -64L -66L -68L -70L -72L -74L -76L

RF Inductors

270 Quaker Rd., East Aurora NY 14052 • Phone 716-652-3600 • Fax 716-652-4814 • E-mail: apisales@delevan.com • www.delevan.com

330 300 285 277 265 229 220 203 193 187 175 170 160 130 118 110 100 90 85 80 70 68 61 59 58 41 40 37 34 29 26 23 21.5 19.5 18.0 16.6 15.8 13.5 12.0

1.5 1.8 2.0 2.2 2.4 3.2 3.4 4.1 4.5 4.8 5.4 5.8 6.4 10.0 12.0 14.0 17.0 20.0 24.0 27.0 34.0 37.0 45.0 48.0 51.0 100.0 105.0 120.0 145.0 195.0 250.0 295.0 365.0 430.0 510.0 605.0 670.0 900.0 1100.0

4.0 3.3 3.2 2.8 2.5 2.3 2.2 2.0 1.9 1.8 1.7 1.6 1.4 1.2 1.15 1.10 0.95 0.86 0.80 0.68 0.64 0.60 0.50 0.47 0.42 0.41 0.32 0.30 0.25 0.24 0.21 0.20 0.18 0.17 0.15 0.14 0.12 0.11 0.10

7907907907907907907907907907907907907902502502502502502502502502502502502507979797979797979797979795050

1009590859095908070656565659590909090908585807565454045454545454040403030303025

± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 15%± 15%± 15%± 15%± 15%± 15%± 15%± 15%± 15%± 15%± 15%± 15%± 15%± 15%

0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.00 1.20 1.50 1.80 2.20 2.70 3.30 3.90 4.70 5.60 6.80 8.20 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120.0 150.0

Optional Tolerances: J = 5% H = 3%

*Complete part # must include series # PLUS the dash #

For surface finish information, refer to www.delevanfinishes.com

1/2009

API_newlayouts_single:APIcatalog_newlayouts 8/24/10 3:43 PM Page 59