MTAC-SkullTAC user guide Layout 1 4/1/13 1:23 PM Page 1 ......MTAC-SkullTAC user guide_Layout 1...

1x-4x-24mm1.5x-6x-40mm

The Ballistic CQ 5.56 / 7.62 reticleThe Ballistic CQ 5.56 / 7.62 reticles were developedfor competitive shooters, law enforcement, andmilitary applications. The circular “donut” in thecenter provides ultra-fast engagement at closedistances, while the smaller dots of the reticleprovide trajectory compensation out to 600 yardsfor the 5.56 62 grain FMJ and 7.62 150 grain FMJcartridges.

600

100200300400500600

000000

5.56 55gr FMJ.243BC 3200fpsSight Height 2.3"Altitude 2000ft

7.62 168gr SMK.462BC 2650fpsSight Height 2.3"Altitude 2000ft

5.56 77gr SMK.372BC 2750fpsSight Height 1.8"Altitude 2000ft

5.56 50gr V-Max.242BC 3300fpsSight Height 2.3"Altitude 2000ft

5.56, 62gr FMJ.307BC 3025fpsSight Height 2.3"Altitude 2000ft

5.56 68gr HMatch.355BC 2850fpsSight Height 2.3"Altitude 2000ft

7.62 150gr FMJ.425BC 2750fpsSight Height 2.3"Altitude 2000ft

100200300400500590

000000

100200300400500600

0+1+2+4+6+8

100200300400500600

.5000

-1-2

100200300400500600

+1.2+1

0-1-3-5

100200300400500600

+.500

-1-1-1

100200300400500600

+.900

-1-2-3

Ballistic CQ Reticle

Windage / Elevation Adjustment The windage and elevation knobs are designed forprecise adjustment. The dials are calibrated so that1 click = .5 MOA. Both dials can be reset to “0”once the scope is sighted-in. To rotate the dial andreset to “0”, insert a small screw driver into the dialslot, located at the base of the turret on the frictionring.

Illuminated Reticle Adjustment The 1x-4x-24mm and 1.5x-6x-40mm feature an illuminated reticle that makes it easier to see the reticle in low light conditions. The intensity of the illumination is controlled by the rotary illumination switch located on the left side of the adjustment turret. The switch has 10 intensity levels and an “Off” position in between each level. The reticle is powered by a 3-volt lithium cell battery #CR2032. To install a new battery, simply unscrew the battery cap on the rotary switch and install the new battery flat side (+) up. It is advisable to remove the battery for long term storage (over a month).

Tech Note

1x-4x-24mm

MTAC-SkullTAC user guide_Layout 1 4/1/13 1:23 PM Page 1

Windage / Elevation Adjustment The windage and elevation dials are calibrated sothat 1 click = .1 mRAD. Both dials offer 5 mils ofadjustment per revolution and they can be reset to“0” once the scope is sighted-in. To reset to “0”,use the hex wrench supplied with the scope toloosen the set screws located at the top of theknob on the elevation and windage adjustmentdials. The dial should spin freely allowing you torotate the dial back to “0”. Do not lift up or removethe dial. Retighten the set screws once the dial isreset.

Tech Note

3.5x-10x-42mm4.5x-14x-42mm6.5x-20x-50mm

G2B Mil-Dot ReticleThe G2B Mil-Dot is a mil-based reticle with 1/2mil hash marks in between each mil dot formore precise aiming, distance measurement,holdover and hold-off for wind. It is a versatile,combat proven reticle that is ideal for mid- tolong-range tactical shooting. The G2B Mil-Dotreticle is paired with Mil-Rad knobs so thatadjustments for windage and elevation correspondwith the reticle calibrations.

The subtension data below corresponds to thescope at the maximum power setting.

Units A B C D E F G H J K LmRad 10 0.5 0.5 0.2 0.06 .5 1 0.06 0.06 5 2in/100 yd. 36 1.8 1.8 0.72 .22 1.8 3.6 .22 .22 18 7.2cm/100 m 100 5.0 5.0 2 0.6 5 10 0.6 0.6 50 20

Reticle SubtensionsBurris Company331 East 8th StreetGreeley, CO 80631(970) 356-1670www.burrisoptics.comINSTR 1038

MTAC-SkullTAC user guide_Layout 1 4/1/13 1:23 PM Page 2