EDGE Creation

Site ID OMLR1TG 100

Excute:TG Level(ABISALLOC&DCP Change)

RXAPP:MO=RXOTG-100; DCP-Start9

RXAPE:MO=RXOTG-100,DCP=9&&11; DEV-StartRBLT2-11081

RXAPI:MO=RXOTG-100,DCP=9&&11,DEV=RBLT2-11081&&-11083,RES64K;

RLSTC:CELL=OMLR1A,STATE=HALTED;

RLSTC:CELL=OMLR1B,STATE=HALTED;

RLSTC:CELL=OMLR1C,STATE=HALTED;

RXBLI:MO=RXOTG-100,SUBORD,FORCE;

RXESE:MO=RXOTG-100,SUBORD;

RXMOC:MO=RXOTG-100,ABISALLOC=FLEXIBLE;

RXMOC:MO=RXOTRX-100-0,DCP1=178,DCP2=179&&186;

RXESI:MO=RXOTG-100,SUBORD;

RXBLE:MO=RXOTG-100,SUBORD;

RLSTC:CELL=OMLR1A,STATE=ACTIVE;

RLSTC:CELL=OMLR1B,STATE=ACTIVE;

RLSTC:CELL=OMLR1C,STATE=ACTIVE;

FPDCHRLGSC:CELL=OMLR1A,FPDCH=1,PSKONBCCH=ENABLED; 1

RLGSC:CELL=OMLR1B,FPDCH=1,PSKONBCCH=ENABLED; 1

RLGSC:CELL=OMLR1C,FPDCH=1,PSKONBCCH=ENABLED; 1

NUMREQBPCRLBDC:CELL=OMLR1A,NUMREQBPC=SYSDEF,NUMREQEGPRSBPC=1,CHGR=1; SYSDEF

RLBDC:CELL=OMLR1B,NUMREQBPC=SYSDEF,NUMREQEGPRSBPC=1,CHGR=1; SYSDEF

RLBDC:CELL=OMLR1C,NUMREQBPC=SYSDEF,NUMREQEGPRSBPC=1,CHGR=1; SYSDEF

EDGE BLOCK_DEBLOCK

RLGSE:CELL=OMLR1A;

RLGSE:CELL=OMLR1B;

RLGSE:CELL=OMLR1C;

RLGSI:CELL=OMLR1A;

RLGSI:CELL=OMLR1B;

RLGSI:CELL=OMLR1C;

RLGSP:CELL=OMLR1A;

RLGSP:CELL=OMLR1B;

RLGSP:CELL=OMLR1C;

RLBDP:CELL=OMLR1A;

RLBDP:CELL=OMLR1B;

RLBDP:CELL=OMLR1C;

RLGRP:CELL=OMLR1A;

RLGRP:CELL=OMLR1B;

RLGRP:CELL=OMLR1C;

DCP-END11

DEV-END11083

PSKONBCCHENABLED

ENABLED

NUMREQEGPRSBPC CHGR1 1

Input cells are in yellow

Prepared by:V.George Emmanuvel

Excute:TRX Level(DCP Change)

RXBLI:MO=RXOTRX-100-0,SUBORD,FORCE;

RXESE:MO=RXOTRX-100-0,SUBORD;

RXESI:MO=RXOTRX-100-0,SUBORD;

RXBLE:MO=RXOTRX-100-0,SUBORD;

TG 100Excute:TRX Level(DCP Change)

RXBLI:MO=RXOIS-100,FORCE;

RXESE:MO=RXOIS-100;

RXESI:MO=RXOIS-100;

RXBLE:MO=RXOIS=100;

To Improve EDGE Throughput

The command for checking that is

The print out for the command will be:

RADIO X-CEIVER ADMINISTRATIONMANAGED OBJECT DATA

MO RSITE AHOP COMB FHOP MODELRXOTG-0 SLM51 ON HYB SY G12

SWVERREPL SWVERDLD SWVERACT TMODE B4405R016H B4405R016H TDM

ABIS64KTHR DHRAABISTHR DFRMAABISTHR0

DAMRCR DAMRREDABISTHR

SDHRAABISTHR SDFRMAABISTHR SDAMRREDABISTHR

PTA JBSDL

TGFID SIGDEL BSSWANTED PACKALG H'0000-008A NORMAL 121

2. Check for the 64K reservation in the E1 attached to the TG.

1. Check for the TG if it is defined for FLEXIBLE in Abis allocation

rxmop:mo=rxotg-(tg number):

CONFMD CONFACT TRACO ABISALLOC CLUSTERID SCGR FASTREC 4 POOL FLEXIBLE

In the printout u can see that the abis allocation is made as flexible instead of the normal FIXED mode.

The command for checking that is

rxapp:mo=rxotg-(tg number):

The print out for the command will be:

If no devices have been reserved, you need to reserve the device as 64K.

This can be done by:

rxmoc: mo=rxotg-(tg number),dcp=dcp number, dev=device name,res64k;

3. We need to check if the TRU’s are configured for EDGE

In the Printout you can see that, 64K reservation has been done for some 9 devices in the E1.

The command to check that is:

rxmop:mo=rxotrx-(tg number)-(trx number);

The printout of that command will be:

The MO side on EDGE definition is done.

This can be checked by the command:

rlbdp:cell=cell name:

The printout of the command is:

In this result you can find that the TRU DCP values are configured for EDGE. I will attach a separate TRU DCP Values for both EDGE and Normal TRU.

4. Check for the cell if the required number of EGPRS (NUMREQEGPRSBPC) is allocated

You can see that NUMREQEGPRSBPC is defined as 5, for Showcase towns. Note that if the TG is not defined for FLEXI ABIS, NUMREQEGPRSBPC is defined as

This can be checked by the command:

rlgsp:cell=cell name;

The printout of the command is:

Once all this check is done then you can rest assure EDGE is working.

command to check type of DRUrxmfp:mo=rxotrx-338-0&&-11;

5. Check for the cell if FPDCH and GPRS Support are allocated

NUMREQEGPRSBPC is defined as 2 and not 5.

EDGE Creation

Documents

Environmental Protection Agency P3 Grant for the Creation ...edge.rit.edu/edge/OldEDGE/public/Archives/P05301/Documents/PDR.… · Environmental Protection Agency P3 Grant for the

Cover illustration: Renée Saunders · CNT’s unique approach combines cutting edge research and analysis, public policy advocacy, the creation of web-based information tools for

creation and valuation of novelty at the marginsedge-conference.de/wp-content/uploads/2019/12/... · Edge probes into the interrelations between generation and valuation of novelty,

KNOWLEDGE CREATION, DIFFUSION, AND USE IN INNOVATION ... · edge and innovation systems and infrastructures (such as innovation networks of networks and knowledge clusters of clusters)

Visible Edge Institute - Core Classes (formerly Pro/ENGINEER) (MA Program # 1101674) Geometry Creation Introduction to Parametric Modeling - Fundamentals Introduction to Parametric

Cutting Edge · 2018. 11. 9. · Cutting Edge advanced Cutting Edge advantage Navigate Cutting Edge advantages Navigate adventure advert Cutting Edge advertise Navigate Cutting Edge

The Co-Creation Edge: Harnessing Big Data to Transform Sales and Procurement for Business

Test-as-a-Service: Accelerate Test. Improve Safety. · • (IMA)Cutting-edge calibration test setups, PathWave software, and accessories • Traffic scenario creation and monitoring

EDUC European Digital UniverCity · EDUC (European Digital UniverCity) will strengthen the European identification process by enhancing knowl-edge creation and by putting forward

A Dynamic Theory of Organizational Knowledge Creation. 2008/Uploaded in... · edge creation, it is important to concentrate on the semantic aspects of information. 2.2. Two Dimensions

THE ORIGINAL EDGE FLASHING - DLM Guide -Manual.pdf · 2019-05-21 · these changes saw the design and creation of the original Flashguard soft edge by DLM over 20 years ago. This

Extending the Edge Drawing Creation Productivity and Performance How-to Session Ricky Black Product Manager Productivity and Performance How-to Session

Anza Borrego Geology Trip Spring 2012 Credits Special ...employees.oneonta.edu/hasbarle/Anza-Borrego-Field...Optional: Geology of Anza-Borrego: Edge of Creation (California Desert

creation re creation

Create an account - Edge Hill Universityeshare.edgehill.ac.uk/14033/1/RefWorks User Guide - v7... · Web view2017-10-23 · Manual Creation. This isn’t something you need to do

Chevalet vibrato Edge/Lo-Pro Edge - · PDF file1 FR Chevalet vibrato Edge/Lo-Pro Edge Edge Lo-Pro Edge ③ ② ⑤ ⑥ ④ ① ① ③ ② ④ ⑥ ⑤ ① ① Arrière ⑦ ⑧ ①Pontet

Sheffield City Region: Supply Chain needs & capabilities ... · ‘High-Value Manufacturing is the application of leading-edge technical knowledge & expertise to the creation of products,

The EDGE Model Teaching EDGE Leading EDGE Trainer ’ s EDGE Teaching EDGE Leading EDGE Trainer ’ s EDGE The first one to fall asleep gets today’s competitive-edge

Effects of shoreline reef creation on edge erosion, marsh resilience and nekton assemblages in south Louisiana

Accelerate NICT Open Innovation · Accelerate NICT Open Innovation ―For the further co-creation stages― Making Cutting-edge Technologies New Social Value through Open Innovation