EDGE Creation

Site ID OMLR1TG 100

Excute:TG Level(ABISALLOC&DCP Change)

RXAPP:MO=RXOTG-100; DCP-Start9

RXAPE:MO=RXOTG-100,DCP=9&&11; DEV-StartRBLT2-11081

RXAPI:MO=RXOTG-100,DCP=9&&11,DEV=RBLT2-11081&&-11083,RES64K;

RLSTC:CELL=OMLR1A,STATE=HALTED;

RLSTC:CELL=OMLR1B,STATE=HALTED;

RLSTC:CELL=OMLR1C,STATE=HALTED;

RXBLI:MO=RXOTG-100,SUBORD,FORCE;

RXESE:MO=RXOTG-100,SUBORD;

RXMOC:MO=RXOTG-100,ABISALLOC=FLEXIBLE;

RXMOC:MO=RXOTRX-100-0,DCP1=178,DCP2=179&&186;












RXESI:MO=RXOTG-100,SUBORD;

RXBLE:MO=RXOTG-100,SUBORD;

RLSTC:CELL=OMLR1A,STATE=ACTIVE;

RLSTC:CELL=OMLR1B,STATE=ACTIVE;

RLSTC:CELL=OMLR1C,STATE=ACTIVE;

FPDCHRLGSC:CELL=OMLR1A,FPDCH=1,PSKONBCCH=ENABLED; 1

RLGSC:CELL=OMLR1B,FPDCH=1,PSKONBCCH=ENABLED; 1

RLGSC:CELL=OMLR1C,FPDCH=1,PSKONBCCH=ENABLED; 1

NUMREQBPCRLBDC:CELL=OMLR1A,NUMREQBPC=SYSDEF,NUMREQEGPRSBPC=1,CHGR=1; SYSDEF

RLBDC:CELL=OMLR1B,NUMREQBPC=SYSDEF,NUMREQEGPRSBPC=1,CHGR=1; SYSDEF

RLBDC:CELL=OMLR1C,NUMREQBPC=SYSDEF,NUMREQEGPRSBPC=1,CHGR=1; SYSDEF

EDGE BLOCK_DEBLOCK

RLGSE:CELL=OMLR1A;

RLGSE:CELL=OMLR1B;

RLGSE:CELL=OMLR1C;

RLGSI:CELL=OMLR1A;

RLGSI:CELL=OMLR1B;

RLGSI:CELL=OMLR1C;

RLGSP:CELL=OMLR1A;

RLGSP:CELL=OMLR1B;

RLGSP:CELL=OMLR1C;

RLBDP:CELL=OMLR1A;

RLBDP:CELL=OMLR1B;

RLBDP:CELL=OMLR1C;

RLGRP:CELL=OMLR1A;

RLGRP:CELL=OMLR1B;

RLGRP:CELL=OMLR1C;

DCP-END11

DEV-END11083

PSKONBCCHENABLED

ENABLED

ENABLED

NUMREQEGPRSBPC CHGR1 1

1 1

1 1

Input cells are in yellow

Prepared by:V.George Emmanuvel

Excute:TRX Level(DCP Change)

RXBLI:MO=RXOTRX-100-0,SUBORD,FORCE;

RXESE:MO=RXOTRX-100-0,SUBORD;


RXESI:MO=RXOTRX-100-0,SUBORD;

RXBLE:MO=RXOTRX-100-0,SUBORD;
























































TG 100Excute:TRX Level(DCP Change)





























































RXBLI:MO=RXOIS-100,FORCE;

RXESE:MO=RXOIS-100;

RXESI:MO=RXOIS-100;

RXBLE:MO=RXOIS=100;

To Improve EDGE Throughput

The command for checking that is

The print out for the command will be:

RADIO X-CEIVER ADMINISTRATIONMANAGED OBJECT DATA

MO RSITE AHOP COMB FHOP MODELRXOTG-0 SLM51 ON HYB SY G12

SWVERREPL SWVERDLD SWVERACT TMODE B4405R016H B4405R016H TDM

ABIS64KTHR DHRAABISTHR DFRMAABISTHR0

DAMRCR DAMRREDABISTHR

SDHRAABISTHR SDFRMAABISTHR SDAMRREDABISTHR

PTA JBSDL

TGFID SIGDEL BSSWANTED PACKALG H'0000-008A NORMAL 121

END

2. Check for the 64K reservation in the E1 attached to the TG.

1. Check for the TG if it is defined for FLEXIBLE in Abis allocation

rxmop:mo=rxotg-(tg number):

CONFMD CONFACT TRACO ABISALLOC CLUSTERID SCGR FASTREC 4 POOL FLEXIBLE

In the printout u can see that the abis allocation is made as flexible instead of the normal FIXED mode.

The command for checking that is

rxapp:mo=rxotg-(tg number):

The print out for the command will be:

If no devices have been reserved, you need to reserve the device as 64K.

This can be done by:

rxmoc: mo=rxotg-(tg number),dcp=dcp number, dev=device name,res64k;

3. We need to check if the TRU’s are configured for EDGE

In the Printout you can see that, 64K reservation has been done for some 9 devices in the E1.

The command to check that is:

rxmop:mo=rxotrx-(tg number)-(trx number);

The printout of that command will be:

The MO side on EDGE definition is done.

This can be checked by the command:

rlbdp:cell=cell name:

The printout of the command is:

In this result you can find that the TRU DCP values are configured for EDGE. I will attach a separate TRU DCP Values for both EDGE and Normal TRU.

4. Check for the cell if the required number of EGPRS (NUMREQEGPRSBPC) is allocated

You can see that NUMREQEGPRSBPC is defined as 5, for Showcase towns. Note that if the TG is not defined for FLEXI ABIS, NUMREQEGPRSBPC is defined as

This can be checked by the command:

rlgsp:cell=cell name;

The printout of the command is:

Once all this check is done then you can rest assure EDGE is working.

command to check type of DRUrxmfp:mo=rxotrx-338-0&&-11;

5. Check for the cell if FPDCH and GPRS Support are allocated

NUMREQEGPRSBPC is defined as 2 and not 5.

Documents

EDGE Creation