ECE 7366 Advanced Process Integration Set 10a: The Bipolar Transistor - Basics Dr. Wanda Wosik Text...

1

ECE 7366 Advanced Process Integration

Set 10a: The Bipolar Transistor - Basics

Dr. Wanda Wosik

Text Book: B. El-Karek, “Silicon Devices and Process Integration”

2

Bipolar Junction Transistors for Digital and Analog Applications

RFAMS

Why BJTs? Performance of SiGe BJTs superior than CMOS by several generation(ex. 115 nm ~385GHz SiGe vs. 20 nm CMOS ~389GHz)

Bipolar Junction Transistors

3

Bipolar Transistors

E-B junction is forward biased=injects minority carriers to the baseBase (electrically neutral) is responsible for electron transport via diffusion (or drift also if the build in electric field exists) to collectorC-B diode is reverse biased and collects transported carries

VBE>0 VBC<0

IE=IEn+IEp IC=aIEa<1

IB=IEp+Irec

IE IC

IB

4

Bipolar Junction Transistors

n-p-nIntegrated circuit BJT

p-n-p Individual device

5

Bipolar Junction Transistors

Currents’ Components

small

6

Bipolar Junction Transistors

n-p-n p-n-p

n+-p p+-n n-pp-n

BJT – injection and transport of carriers as well as capacitance and resistances optimized for gain, speed, and power.

Doping asymmetry; see F-level in Emitter in n-p-n and p-n-p transistors.

7

Notation and Biasing for Bipolar Junction Transistors

8

Charge Distributions in p-n-p Transistors Under Bias

9

BJT Operation

Common emitter

Common base

10

p-n-p BJT Energy Band Diagram

Thermal equilibrium

Forward bias condition

Holes are minority carriers injected from E to B

11

Idealized BJT Structure

• Base is short: Ln>>WB i.e. no recombination• Emitter is transparent: Lp>>WE • Low field in the depletion layers: no ionization i.e no breakdown• Leakage currents low• No recombination in the E-B space charge region

•Doping asymmetry•Doping uniformity in all regions

1212

Idealized BJT StructureForward Biasing Condition

Emitter efficiency

Base transport factor:

Current gain in CB configuration

Current gain in CE configuration

13

Planar TransistorStructure and Doping

n+

NE>>NB>>NC

E-field

Intrinsic base: short (Wb<<Lp); pinch-off base

Short emitterThe role of contact

Arsenic used in the buried layer• slow diffusion into epilayer• collector voltage not degraded by n+ diffusion

As vs P

Process integration of collector plug doping

Dopant distributions to ensure high injection g and transport a

As

14

Low Level Injection ParametersElectron Injection to the BaseBuilt-in E-field

Electron component of Emitter region

No recombination in the base

Gummel base number

For high doping – bandgap narrowingStrong effect in emitter

Note: Base is short

15

Note: Base is short but emitter is long

Electron current

Injection of Minority Carriers

Hole current

NA(x) <<NDE(x)

µpE<<µnB

niE2(x)>>niB

2(x) DEg(N) Bandgap narrowing

tpE<<tnB SRH & Auger≅f(N)

Emitter injection efficiency next

16

Emitter injection efficiency

Emitter Injection Efficiency and Current Gain

Current gain CB configuration

CE configuration

Need largeGE

Need smallGB

Recombination in the SCR

At high VBE High injection levels:

•Dnp≈pp(x)•ohmic voltage drop• base width modulation

Gummel Plots

17

Transport of Minority Carriers

Diffusion length vs. base width

Recombination in the base

No built-in E-field – diffusion current only

Base Current Components • Hole injection into emitter (to decrease, use high doping levels in E)• Generation current in C-B junction (no defects)• Recombination in the neutral base base (insignificant – base short)• Recombination in the E-B space charge region and the junction surface (depletion layer – defects)

18

Collector-Base Reverse Characteristics

Common Emitter configuration

Open base

Early voltage

Can lead to second breakdown

BJT are not symmetrical reverse operation conditions• injection at C-B junction is small (collector doping the lowest)• transport in the base poor (E-field retards carrier drift)

b with Ic due to high injection levels (also Kirk effect)

bR<<bF

19

Bipolar Junction TransistorsForward Operation Mode Early Effect

Early Voltage

20

Bipolar Junction TransistorsBreakdown Voltages

Common BaseCommon Emitter

Collector-Base junction

IB=0

Multiplication factor

21

Emitter Base Reverse Characteristics

High dopants’ concentrations in E-B junction• Surface concentrations are the highest • Hot carriers possible to increase recombination-generation there

• current gain decreases.

Reverse Early Voltage much larger than VA

Reverse Punch-Through Voltage

Ex. NA(0)=2.5E18cm-3 , NA(Wb)=5E16cm-3 VPT≈3.3V – before VEB0

22

Polysilicon Emitter and Interface Oxide

Emitter: Arsenic poly-Si doped • implant into poly•anneal polySi+c-Si junction (<50nm)

Contact away from the junction (leakage) – poly also plays a role of sacrificial layer

•Emitter is self aligned to base (capacitance, resistance, speed) •Extrinsic base contact made in p+-poly-Si• Shallow trench isolation (STI) at junctions reduces capacitances

Double poly n-p-n Scaling of BJTs requires shallow junctions and small areas: use polySi+self aligned structures

This transistor results in a smaller base current: injection into c-Si, tunneling through oxide, recombination in the poly-Si

23

Interface Oxide (IFO)

In c-Si long emitters recombination in the bulk

PolySi emitter• Transport of carriers into poly (Lp>xjE) • Interface poly/c-Si important for

recombination

Larger barrier height for holes that for electrons (δ≈4Å)

Degenerated semiconductor

Forward bias condition

For short E (20-50nm) no recombination in Eholes reach contact (leakage)

For thin oxide 1nm IB limited by tunneling

24

Polysilicon Emitters: SIMS Resultsn-p-n transitor

p-n-p transitor

1nm oxide

•Oxide thickness control by CVD, RTO, Atomic Layer Deposition•No oxide: epitaxial growth•Oxide breaks-ups: local recrystallization –

junction nonuniformity (lower current gain)• Segregation of dopant at the interface

SIC- selective implanted colector

25

Narrow-Emitter Effects

Reduction of current gain because:• E-Gummel number decreases and leads to lateral

injection of holes from the base (not big - if tunneling is dominating)

• Shadowing and aspect ratio effects reduce doping at the E perimeter

• Poly-Si grains columnar (postimplant anneal)– less diffusion in lateral direction – less perimeter doping due to this edge effect

• Self-aligned E-B junction: extrinsic base encroachment – compromise b/w resistance and injection.

• Width of emitter degrades further the injection

3D effects in small devices

26

Transistor Resistances Scaling: Frequency Response, Conductance And Switching Speed

Emitter-Base

Collector-Base

Emitter Resistance 1/AEPoly-Si emitters: •Contact resistance b/w metal/silicide and poly•Poly/mono Si interface resistance (IFO)•Vertical resistance in poly (dopants, grains, thickness – watch for silicide penetration)•Vertical resistance of c-Si emitter (doping)

27

Measurements of Emitter Resistance

Measurements: • ac (watch for parasitic capacitances),• dc widely used – here floating collector

• IB(VCEsat)

When E-B and C-B junctions become forward biased Parasitic transistors affect E resistance

High impedance voltmeter

28

Base Resistance

Extrinsic and Intrinsic (active) base

Ideal diodes plots ~60mV/decade

Use 4 point probe for the sheet resistance in both regions

Also SIMS, Spreading Resistance measurements (depends on depth).

Heavy doping effects may be important – Kirk effect

29

Geometry of BJT – Extrinsic Base Resistance

RBint>>RBext

DVBE(y) develops when base current flows

Nonuniform biasing at E-B junction – emitter crowding effect

Low injection

Make interdigitated geometry for emitters in high power devices PE/AE

Base spreading resistance – nonuniform along the emitter junction

Intrinsic base resistance high

30

Effective Base ResistanceAssume:RBint=24kW/sq

Apply bias:Rbint<RB0

Probe the transistor base here

RBint≈RB0/3 at low IC. At high IC, RBint and RBRBex b/c of emitter crowding effect (current crowding)npn transitor with double base contact- pinch-off resistor

31

Breakdown Voltages – Influence Of Base Resistance

32

Collector Resistance

Resistance of the Collector

Collector resistance extracted from: test structures, SIMS, SRP versus depth.

The “fly-back” (RE method not good – injected carriers in reverse operation - affect measurements)