View
251
Download
5
Category
Preview:
Citation preview
ALL TAXES EXTRA. ALL PRICES F.O.B. FACTORY. LIST PRICES SHOWN IN CANADIAN DOLLARS.PRICES SUBJECT TO CHANGE WITHOUT NOTICE. WE RESERVE THE RIGHT TO CORRECT PRICING ERRORS.
BERKELEY® CENTRIFUGAL PUMPS AND ACCESSORIES
CANADA 2017 LIST PRICESCB1525P_CAN • EFFECTIVE: MARCH 1, 2017 • SUPERSEDES ALL PREVIOUS PRICE LISTS
2 CB1525P_CAN (03/01/17)
TABLE OF CONTENTS
Page General Information
Ordering Information 3Certified Test Charges 3Pump Model Nomemclature 4
Small Stainless Centrifugals“SSCX” Stainless Steel Centrifugal Pumps 5“C” Single-Stage Motor Drive 7SSHM-2 Horizontal Multi-Stage Pumps 7
Type “B” Closed Coupled CentrifugalsElectric Motor Drive
T Series, 6” – Nominal Impeller Diameter 8W Series, 7” – Nominal Impeller Diameter 11Z Series, 9” – Nominal Impeller Diameter 12E Series, 10” – Nominal Impeller Diameter 18G Series, 12” – Nominal Impeller Diameter 20J Series, 13” – Nominal Impeller Diameter 22EX Series, 15”, EY Series, 18” – Nominal Impeller Diameters 25
Electric Self Priming 26Seal Adders 26Close Coupled Pump Motors 27-29Pentek Intellidrive™ XL 30PPX Three Phase Pump Panels 38
Type “B” Frame MountHydraulic, Belt and Coupling Drives Frame Mount & Self-Priming
Z Series, 9” – Nominal Impeller Diameter 39E Series, 10” – Nominal Impeller Diameter 42G Series, 12” – Nominal Impeller Diameter 43J Series, 13” – Nominal Impeller Diameter 44EX Series, 15” – Nominal Impeller Diameter 45EY Series, 18” – Nominal Impeller Diameter 45
PageType “B” SAE Engine Mount – For Flywheel Housings
SAE Centrifugal pumpsZ Series, 9” – Nominal Impeller Diameter 46E Series, 10” – Nominal Impeller Diameter 47G Series, 12” – Nominal Impeller Diameter 48J Series, 13” – Nominal Impeller Diameter 49EX Series, 15” – Nominal Impeller Diameter 50XT Series, 15.5” – Nominal Impeller Diameter 51EY Series, 18” – Nominal Impeller Diameter 51
SAE Self-Priming 52SAE Flywheel Couplings 52
Type “B” Air Cooled (Gas) PumpsAir-Cooled Engine Drives – End Suction 53Air-Cooled Engine Drives – Self-Priming 53
Wastewater/Trash PumpsB-AG Series Submersible 54
AccessoriesFlange Kits and Impeller Cutting Charges 55Discharge Priming Valves 56
NEW!
CB1525P_CAN (03/01/17)3
PRODUCT AND ORDERING INFORMATION
Certified Pump TestingElectric Motor Drive Centrifugal Pumps
The following information is required with each order.1. Pump Model Number2. Motor Horsepower3. Catalog Number4. Impeller Diameter5. Required Flow Rate, Head and RPM6. Optional Flow Rate, Head and RPMCONNECTION OPENINGS – Suction and Discharge openings are NPT tapped for standard pipe, or faced and drilled per ANSI B16.1, class 125 for standard flanges as indicated. Maximum working pressure for class 30 cast iron, per ANSI B16.1, is 175 PSI unless otherwise stated on pump curve. List price for cast iron companion flanges includes threaded flange for standard pipe, gaskets, bolts and nuts, and can be found on page 55.PRICES INCLUDE – Assembed pump and motor. BASIC PUMP AND MOTOR – Pump end and bracket assembled on standard horizontal close-coupled motor.BERKELEY® reserves the right to use the motor manufacturer of its choice. Units specified (ordered) with specific motor manufacturer maybe subject to additional charges and lead times.Consult factory for TEFC motors not listed on price sheets. Part-wind start motors are available. Consult factory for delivery times.
MOTOR VOLTAGESSingle-phase motors showing both 115 and 230 volts, and three-phase motors showing both 230 and 460 volts as standard, are reconnectable for either voltage, 230 volt motors WILL NOT operate on 208 volt systems. For 208 volt systems, order 200 volt motor. **200V motors subject to additional charges.PUMP CASES – All pump cases are cast iron.BRACKETS – All brackets are cast iron.IMPELLERS – Cast iron and bronze (see price sheet). Pricing for special impeller trims is listed on page 55.SHAFT SEALS – Seal materials are ceramic carbon, Buna-N, and 300 Series stainless steel generally suitable for water to 200°F. All models ending with the letter “S” are fitted with mechanical shaft seal. Special seals may be available, consult factory. Stuffing box is standard on all other models.PACKING – Fiber-metallic packing is used in stuffing box models. For special pumping applications (liquids other than water), consult factory.WEAR RINGS – All wear rings are bronze.
SHAFT SLEEVES – All shaft sleeves are stainless steel.
SPECIAL CONSTRUCTION AND MATERIALSALL IRON – List price additions for all-iron construction include cast iron bracket, cast iron case, cast iron impeller, packing gland, cast iron wear ring (where used), stainless steel shaft sleeve, and corrosion-resistant bolts, nuts and capscrews.ACCESSORIES – Items of equipment frequently required to complete the pump installation may be ordered separately from sections of the catalog accessories.
VOLUTE ORIENTATION
HP Phase 115V 200V** 230V 460V 575V1 thru 1-1/2 1 available available standard refer to factory
2 thru 10 1 N/A available standard refer to factory1 thru 40 3 N/A available standard standard available
50 thru 200 3 N/A available available standard available
Performance TestsNet PricePart Number Description
CTEST01 Non-Witnessed Performance Test with no NPSH
$900 NET
CTEST02 Customer Witnessed Performance Test with no NPSH Test
CTEST03 Non-Witnessed Performance with 1 Point NPSH Test
CTEST04 Customer Witnessed Performance with 1 Point NPSH Test
CTEST05 Non-Witnessed Certified Hydrostatic Test
$129 NETCTEST06 Witnessed Certified Hydrostatic Test
NOTES:• Certified tests shall be factory laboratory tests conducted in accordance
with the edition of ANSI/HI 1.6 and ANSI/HI 2.6 test standards. Test will be evaluated to Level B requirements.
• If the measured performance is within -3% to +5% of the published rating point or the customer specified rating point, the pump will be shipped along with the documentation.
• The factory reserves the right to modify the impeller diameter in order to meet the published or customer specified rating point.
• Head Capacity at the pump casing discharge and amperage draw by the motor will be provided on the certified performance curve.
• Power available for testing is 230/1/60, 230/460/3/60, 600/3/60. Customer’s power requirements must match factory’s power available. Pumps will be tested at synchronous motor speed.
• All pumps are NPSH tested using vacuum tank suppression.• For certified testing of frame mount, SAE and air-cooled engine drive
pumps, please contact factory.• Pump will be shipped to location specified on Customer Purchase Order
within 24-48 hours from testing completion in Pentair Delavan Lab and receipt of customer approval of test results. Pump(s) will not be held in Lab after this period. A copy of the pump tests will be provided to the fax number on the Customer’s Purchase Order.
Viewed fromthis direction
Viewed fromthis direction
Pump with aClockwise
Rotation
Pump with aCounter-Clockwise
Rotation(Standard Option on Frame Mount)
Clo
ckw
ise
rotation
As viewed As viewed
Counter-Clockwise
12
6
39
12
6
39
RotationVolute Orientation
(viewed from driver end of pump)
Clockwise
T1 T2 (Default) T3 T4
Counterclockwise (Std. option on frame mount)
4 CB1525P_CAN (03/01/17)
TYPE “B” PUMP MODEL NOMENCLATURE
B 4 G P B H SType Of ConstructionB="Back Pull-Out" Design
Discharge Size (Inches)
Nominal Impeller Diameter (Inches)3" = A 7" = W 11" = F 15" = EX 18" = EY4" = M 8" = Y 12" = G 15.5" = XT 19" = EZ5" = X 9" = Z 13" = J 16" = ET 20" = EE6" = T 10" = E 14" = N 17" = EW
Type of DriveP = Electric Motor - Pump Attached Directly
to Motor FrameQ = Engine Drive - Pump Attached Directly
to Engine FrameR = Frame Mounted Belt or Flexible Coupling DriveRM = Special Duty Mounting Frame
Special Features (Optional)B = Hydraulically Balanced Impeller DesignK = Self-Priming
Relative Capacity of ImpellerLL = Very LowL = LowM = Medium (Often Omitted)H = HighHH = Very High
Number Of Stages (Optional)(Single stages not indicated)
Shaft Seal (Optional)S = Mechanical Seal (Packed Stuffing Box is not indicated)
Horsepower of Motor or Engine (Normally indicated on Engine Driven Pumps only)
B –
4 –G –
P –
B –
H –
2 –
S –
10 –
4" x 6" x 13" B H Discharge Size (Inches)
Suction Size (Inches)
Nominal Impeller Diameter (Inches)3" = A 7" = W 11" = F 15" = EX 18" = EY4" = M 8" = Y 12" = G 15.5" = XT 19" = EZ5" = X 9" = Z 13" = J 16" = ET 20" = EE6" = T 10" = E 14" = N 17" = EW
Special Features (Optional)B = Hydraulically Balanced Impeller Design
Relative Capacity of ImpellerLL = Very LowL = LowM = Medium (Often Omitted)H = HighHH = Very High
4" –
6" –
13"–
B –
H –
The model configurations above illustrate the complete range of closed coupled product identification numbers.
NAME PLATE EXAMPLE: PUMP SIZE EXAMPLE:
CB1525P_CAN (03/01/17)5
SMALL STAINLESS CENTRIFUGALS
Berkeley® SSCX Series
Electric Motor Drive, Noryl Impeller
Model No. HPVoltage/
Phase EnclosureSuction
SizeDischarge
SizeCatalog
No. List PriceWeight
(lbs)
SS1XN-1⁄2 1/2
115/230-1ODP
1-1/4” 1”
B78635 $847 22230/460-3 B78636 868 26115/230-1
TEFCB78647 1,088 32
230/460-3 B78648 1,106 29
SS1XN-3⁄4 3/4
115/230-1ODP
1-1/4” 1”
B78637 921 25230/460-3 B78638 946 23115/230-1
TEFCB78649 1,159 37
230/460-3 B78650 1,216 32
SS1XN-1 1
115/230-1ODP
1-1/4” 1”
B78639 1,009 27230/460-3 B78640 1,014 22115/230-1
TEFCB78651 1,220 40
230/460-3 B78652 1,337 35
SS1XN-11⁄2 1-1/2
230-1ODP
1-1/4” 1”
B78641 1,106 32230/460-3 B78642 1,143 28
230-1TEFC
B78653 1,431 50230/460-3 B78654 1,492 37
SS11⁄4XN-2 2230-1
ODP1-1/2” 1-1/4”
B78643 1,396 36230/460-3 B78644 1,304 31
230-1 TEFC B78655 1,582 52
SS11⁄4XN-2-1/2 2-1/2230-1
ODP 1-1/2” 1-1/4”B78645 1,554 37
230/460-3 B78646 1,536 33The standard seal in a SSCX series pump with a Noryl Impeller is a Buna-Carbon/Ceramic. The volute uses a Buna O-Ring to seal the pumping chambers. Use the Seal Options below to upgrade your seal selection.
Mechanical Seal Options
Seal FacesElastomers – Mechanical
Seal & Pump Volute
ODP and TEFCSS_XN Seal Adder
List PriceCarbon / Ceramic Buna IncludedCarbon / Ceramic Viton $64 Carbon / Silicon Carbide Viton 113 Silicon Carbide Viton 170
6 CB1525P_CAN (03/01/17)
SMALL STAINLESS CENTRIFUGALS
Berkeley® SSCX Series
Electric Motor Drive, Stainless Steel Impeller
Model No. HP Voltage/Phase EnclosureSuction
SizeDischarge
SizeCatalog
No. List PriceWeight
(lbs)
SS1XS-3⁄4 3/4
115/230-1ODP
1-1/4” 1”
B82411 $1,152 25230/460-3 B82412 1,218 23115/230-1
TEFCB82413 1,364 37
208-230/460-3 B82414 1,427 32
SS1XS-1 1
115/230-1ODP
B82415 1,239 27230/460-3 B82416 1,304 22115/230-1
TEFCB82417 1,436 40
208-230/460-3 B82418 1,498 35
SS1XS-11⁄2 1-1/2230-1
ODPB82419 1,410 32
230/460-3 B82420 1,338 28230-1 TEFC B82421 1,604 50
SS1XS-2 2230-1
ODPB82423 1,604 36
230/460-3 B82424 1,493 31
SS1XS-21⁄2 2-1/2230-1
ODPB82427 1,774 37
230/460-3 B82428 1,757 33The standard seal in a SSCX series pump with a Stainless Steel Impeller and ODP motor is Viton-Carbon/Ceramic. For TEFC equipped pumps a Viton-Silicon Carbide seal is included. Use the Seal Options below to upgrade your seal selection.
Mechanical Seal Options
Seal FacesElastomers – Mechanical
Seal & Pump Volute
With ODP Motor With TEFC MotorSS_XS Seal Adder
List PriceSS_XS Seal Adder
List PriceCarbon / Ceramic Viton Included N.A.Carbon / Silicon Carbide Viton $112 N.A.Silicon Carbide Viton 161 Included
N.A. = Not available
CB1525P_CAN (03/01/17)7
SMALL STAINLESS CENTRIFUGALS
Berkeley® C Series
Electric motor drive, cast iron construction, silicon bronze impeller
Model Number HP
ODP Single-Phase 230V
ODP Three-Phase 230/460V
Weight Lbs.
Maximum Working Pressure
(PSI)
Suction Dimensions
(in.)
Discharge Dimensions
(in.)Catalog Number List Price
Catalog Number List Price
C1-1/4TPMS 3 B53602S $2,534 B53603S $2,520 55 110 1-1/2” NPT 1-1/4” NPTC1-1/2TPHS 3 B59212S 2,717 B59213S 2,330 56 110 2” NPT 1-1/2” NPT
C2MPS 3 B53616S 2,643 B53617S 2,517 55 100 2-1/2” NPT 2” NPT
Berkeley® SSHM-2 Horizontal Multi-Stage Pumps Electric Motor Drive, Self-Priming
HP Voltage/Phase Catalog No. List Price Weight (lbs)
Max. Working Pressure Suction Discharge Stages
2 230-1 B86073 $1,743
95 130 Lbs. 1-1/2” 1-1/4”32 230/460-3 TEFC B86074 1,985
2 230-1 B82456-01 1,960 42 230/460-3 TEFC B82639 2,044
“C” Series Mounting Dimensions
8 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® T Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
6” – Nominal Impeller Diameter
Model Number (Size) HP
RPM Shaft Seal Impeller Material
Volute Con-nection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B1-1/2TPL 3
3600 PackingCast Iron
NPT
B53747 $3,777 B51592 $3,681 105(1-1/2 x 2 x 6 L) 5 B53748 4,312 B53749 3,927 145
5 Silicon Bronze B74385 4,270 B74386 3,919 145
B1-1/2TPLS 3
3600 MechanicalCast Iron
NPT
B54493 3,454 B54497 3,324 105(1-1/2 x 2 x 6 L) 5 B54494 3,987 B54498 3,563 145
5 Silicon Bronze B74388 3,961 B74389 3,571 145
B1-1/2TPM 5
3600 Packing
Cast Iron
NPT
B58143 4,338 B58144 3,964 145(1-1/2 x 2 x 6 M) 7.5 B58145 4,962 B58146 4,174 165
10 B58147 5,625 B58148 4,731 2205 Silicon
Bronze
B74394 4,303 B74393 3,954 1457.5 B74401 4,897 B74405 4,155 16510 B74414 5,529 B74413 4,690 200
B1-1/2TPMS 5
3600 Mechanical
Cast Iron
NPT
B58083 4,017 B58084 3,590 145(1-1/2 x 2 x 6 M) 7.5 B58085 4,682 B58086 3,801 165
10 B58087 5,340 B58088 4,416 2005 Silicon
Bronze
B74397 3,988 B74396 3,603 1457.5 B74409 4,628 B74407 3,806 16510 B74419 5,257 B74418 4,391 200
B2TPM 3
3600 Packing
Cast Iron NPT
B53765 3,860 B51603 3,783 105(2 x 2-1/2 x 6 M) 5 B53766 4,402 B53768 4,030 145
7.5 B53767 5,015 B53769 4,252 16510 B55576 5,724 B53770 4,839 2003
Silicon Bronze NPT
B73843 3,746 B73844 3,755 1055 B73848 4,379 B73849 3,999 145
7.5 B73853 4,925 B73857 4,205 16510 B73861 5,623 B73862 4,801 2003
Silicon Bronze Flanged
B74443 3,858 B74444 3,779 1055 B74447 4,361 B74448 4,021 145
7.5 B74451 4,951 B74454 4,230 16510 B74457 5,623 B74458 4,801 200
B2TPMS 3
3600 Mechanical
Cast Iron NPT
B54528 3,546 B54533 3,431 105(2 x 2-1/2 x 6 M) 5 B54529 4,089 B54534 3,680 145
7.5 B54530 4,764 B54535 3,894 16510 B54648 5,423 B54536 4,516 2003
Silicon Bronze NPT
B73864 3,546 B73865 3,441 1055 B73867 4,062 B73868 3,686 145
7.5 B73870 4,709 B73872 3,896 16510 B73876 5,336 B73877 4,482 2003
Silicon Bronze Flanged
B74460 3,546 B74461 3,441 1055 B74463 4,062 B74464 3,686 145
7.5 B74466 4,709 B74468 3,896 16510 B74471 5,336 B74472 4,482 200
B2-1/2TPM 3
3600 Packing Cast Iron NPT
B53793 3,947 B51620 3,854 105(2-1/2 x 3 x 6 M) 5 B53794 4,464 B53796 4,101 145
7.5 B53795 5,147 B53797 4,319 16510 B55577 5,806 B53798 4,940 20015 B53799 5,361 205
CB1525P_CAN (03/01/17)9
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® T Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
6” – Nominal Impeller Diameter
Model Number (Size) HP
RPM Shaft Seal Impeller Material
Volute Con-nection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B2-1/2TPM 3
3600 Packing Cast Iron Flanged
B75939 3,768 B75940 3,693 105(2-1/2 x 3 x 6 M) 5 B75943 4,278 B75944 3,930 145
7.5 B75947 4,933 B75950 4,139 16510 B75953 5,564 B75954 4,734 20015 B75957 5,138 205
B2-1/2TPMS 3
3600 Mechanical
Cast Iron NPT
B54562 3,629 B54570 3,516 105(2-1/2 x 3 x 6 M) 5 B54563 4,168 B54571 3,766 145
7.5 B54564 4,851 B54572 3,983 16510 B54650 5,512 B54573 4,612 20015 B54574 5,032 2053
Cast Iron Flanged
B75968 3,478 B75969 3,370 1055 B75971 3,994 B75972 3,609 145
7.5 B75974 4,649 B75976 3,817 16510 B75979 5,282 B75980 4,420 20015 B75983 4,822 2053
Silicon Bronze NPT
B73968 3,620 B73969 3,528 1055 B73971 4,135 B73972 3,764 145
7.5 B73974 4,790 B73976 3,975 16510 B73980 5,426 B73981 4,575 20015 B73983 4,978 205
3 Silicon Bronze Flanged B74550 3,620 B74551 3,528 105
B2-1/2TPMS 1
1800 Mechanical
Cast Iron NPTB54559 2,474 B54567 2,478 100
(2-1/2 x 3 x 6 M) 1.5 B54560 2,634 B54568 2,577 1102 B54561 2,792 B54569 2,674 1101
Cast Iron FlangedB75959 2,371 B75960 2,375 100
1.5 B75962 2,525 B75963 2,470 1102 B75965 2,675 B75966 2,563 1101 Silicon
Bronze NPTB73959 2,520 B73960 2,521 100
1.5 B73962 2,660 B73963 2,618 1102 B73965 2,790 B73966 2,709 1101 Silicon
Bronze FlangedB74541 2,511 B74542 2,521 100
1.5 B74544 2,660 B74545 2,618 1102 B74547 2,806 B74548 2,709 110
B3TPM 7.5
3600 Packing
Cast Iron NPT
B53814 5,250 B53815 4,403 175(3 x 4 x 6 M) 10 B55578 5,915 B53816 5,052 210
15 B53817 5,480 21520 B51633 6,208 3257.5
Cast Iron Flanged
B70084 5,222 B70116 4,403 17510 B70087 5,915 B70118 5,052 21015 B70119 5,480 21520 B70122 6,208 3257.5
Silicon Bronze NPT
B74736 5,173 B74740 4,367 17510 B74744 5,815 B74745 5,001 21015 B74749 5,408 21520 B74753 6,110 3257.5
Silicon Bronze Flanged
B74771 5,173 B74774 4,367 17510 B74777 5,815 B74778 5,001 21015 B74781 5,408 21520 B74784 6,110 325
10 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® T Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
6” – Nominal Impeller Diameter
Model Number (Size) HP
RPM Shaft Seal Impeller Material
Volute Con-nection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B3TPMS 7.5
3600 Mechanical
Cast Iron NPT
B54589 4,935 B54596 4,072 175(3 x 4 x 6 M) 10 B54651 5,597 B54597 4,707 210
15 B54598 5,124 21520 B56695 5,991 3257.5
Cast Iron Flanged
B70102 4,935 B70129 4,072 17510 B70380 5,597 B70131 4,707 21015 B70134 5,124 21520 B70137 5,991 3257.5
Silicon Bronze NPT
B74755 4,871 B74757 4,066 17510 B74761 5,508 B74762 4,666 21015 B74766 5,067 21520 B74768 5,895 3257.5
Silicon Bronze Flanged
B74847 4,871 B74849 4,066 17510 B74852 5,508 B74853 4,666 21015 B74856 5,067 21520 B74859 5,895 325
B3TPMS 1
1800 Mechanical
Cast Iron NPT
B54585 3,233 B54592 3,285 115(3 x 4 x 6 M) 1.5 B54586 3,369 B54593 3,352 125
2 B54587 3,501 B54594 3,412 1253 B69874 3,854 B69872 3,551 1601
Cast Iron Flanged
B70090 3,233 B70125 3,302 1151.5 B70092 3,369 B70126 3,352 1252 B70097 3,501 B70127 3,412 1253 B70099 3,854 B70128 3,551 1601
Silicon Bronze NPT
B74806 3,242 B74807 3,318 1151.5 B74809 3,369 B74810 3,370 1252 B74812 3,494 B74813 3,427 1253 B74815 3,836 B74816 3,560 1601
Silicon Bronze Flanged
B74834 3,242 B74835 3,318 1151.5 B74837 3,369 B74838 3,370 1252 B74840 3,494 B74841 3,427 1253 B74843 3,836 B74844 3,560 160
B3TPH 25 3600 Packing Silicon Bronze
NPT B66871S 7,385 380(3 x 4 x 6 H) Flanged B70140S 7,385 380B3TPHS 25 3600 Mechanical Silicon
BronzeNPT B66873S 6,827 380
(3 x 4 x 6 H) Flanged B70144S 6,827 380B3TPH 3 1800 Packing Silicon
BronzeNPT B66552S 4,390 B66553S 4,136 160
(3 x 4 x 6 H) Flanged B70105S 4,407 B70139S 4,136 160B3TPHS 3 1800 Mechanical Silicon
BronzeNPT B66554S 4,097 B66555S 3,800 160
(3 x 4 x 6 H) Flanged B70108S 4,097 B70143S 3,800 160B3TPHH 20 3600 Packing Silicon
Bronze Flanged B82477 7,593 355(3 x 4 x 6HH) 25 B82475 8,132 400B3TPHHS 20 3600 Mechanical Silicon
Bronze Flanged B82478 7,593 355(3 x 4 x 6HH) 25 B82476 8,132 400
NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required.Three phase motors used meet premium efficiency levels (NEMA MG 1-2011, Table 12-12, 20A or 20B).
CB1525P_CAN (03/01/17)11
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® W Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
7” – Nominal Impeller Diameter
Model Number
(Size) HP RPM Shaft SealImpeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B1WP 33600 Packing Silicon
Bronze NPTB55567S $3,971 B53697S $3,882 110
(1 x 1-1/2 x 7) 5 B55568S 4,448 B55569S 4,140 1507.5 B58132S 5,093 B55570S 4,368 170
B1WPS 33600 Mechanical Silicon
Bronze NPTB54485S 3,522 B54486S 3,402 110
(1 x 1-1/2 x 7) 5 B54487S 4,078 B54488S 3,645 1507.5 B54489S 4,701 B54490S 3,872 170
B5WP 51800 Packing Silicon
Bronze FlangedB51920S 7,959 B51922S 7,772 265
(5 x 6 x 7) 7.5 B51921S 8,721 B51923S 8,309 30510 B51924S 8,630 330
B5WPS 51800 Mechanical Silicon
Bronze FlangedB62577S 8,818 B68315S 8,739 265
(5 x 6 x 7) 7.5 B62579S 9,604 B62580S 9,272 30510 B68316S 10,323 B62581S 9,600 330
NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required.Three phase motors used meet premium efficiency levels (NEMA MG 1-2011, Table 12-12, 20A or 20B).
12 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® Z Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
9” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B1-1/2ZPL 7.5
3600 Packing
Cast Iron
NPT
B53750 $5,363 B53751 $4,403 175(1-1/2 x 2 x 9 L) 10 B55574 6,027 B53752 4,924 210
15 B53753 5,346 2157.5 Silicon
Bronze
B66487S 5,510 B66488S 4,552 17510 B66491S 6,173 B66492S 5,082 21015 B66493S 5,502 215
B1-1/2ZPLS 7.5
3600 Mechanical
Cast Iron NPT
B54499 4,751 B54500 3,891 175(1-1/2 x 2 x 9 L) 10 B54646 5,418 B54502 4,499 210
15 B54504 5,169 21520 B08607 6,458 3357.5
Silicon Bronze NPT
B66489S 4,899 B66490S 4,049 17510 B66832S 5,561 B66833S 4,658 21015 B66841S 5,327 21520 B78660 6,070 335
B1-1/2ZPH 15
3600 Packing
Cast Iron
NPT
B53759 6,110 210(1-1/2 x 2 x 9 H) 20 B52296 6,856 335
25 B52297 7,370 38015 Silicon
Bronze
B74423 6,003 21020 B74427 6,728 33525 B74431 7,241 380
B1-1/2ZPHS 15
3600 Mechanical
Cast Iron
NPT
B54520 5,253 210(1-1/2 x 2 x 9 H) 20 B54074 6,522 335
25 B54075 7,036 38015 Silicon
Bronze
B74435 5,188 21020 B74437 6,408 33525 B74439 6,902 380
B1-1/2ZPHS 3 1800 Mechanical Silicon Bronze NPT B75253 3,882 B75254 3,837 159(1-1/2 x 2 x 9 H)
B2ZPL 10
3600 Packing
Cast Iron NPTB55571 6,309 B55572 5,528 220
(2 x 2-1/2 x 9 L) 15 B55573 5,944 25420 B55561 6,654 34010 Silicon
Bronze NPTB73881 6,187 B73882 5,330 215
15 B73886 5,855 22020 B73890 6,538 34010 Silicon
Bronze FlangedB74476 6,187 B74477 5,463 215
15 B74480 5,855 22020 B74483 6,538 340
B2ZPLS 10
3600 Mechanical
Cast Iron NPTB55562 5,762 B55563 4,856 215
(2 x 2-1/2 x 9 L) 15 B55564 5,278 22020 B55565 6,509 34010 Silicon
Bronze NPTB73894 5,637 B73895 4,805 215
15 B73899 5,213 22020 B73901 6,388 34010 Silicon
Bronze FlangedB74486 5,637 B74487 4,805 215
15 B74490 5,213 22020 B74492 6,388 340
B2ZPH 25 3600 Packing Cast Iron NPT B58067 7,736 415(2 x 2-1/2 x 9 H) 30 B58149 8,969 490
CB1525P_CAN (03/01/17)13
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® Z Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
9” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B2ZPHS 25
3600 Mechanical
Cast Iron NPT B58068 7,370 415(2 x 2-1/2 x 9 H) 30 B58069 8,688 490
25 Cast Iron Flanged B76253 7,063 41530 B76304 8,326 490
30 Silicon Bronze Flanged B85787 8,393 400
B2-1/2ZPL 15
3600 Packing
Cast Iron
NPT
B53800 6,216 235(2-1/2 x 3 x 9 L) 20 B51626 6,933 345
25 B51627 7,426 39030 B53801 8,706 46015
Silicon Bronze
B66536S 6,560 23520 B66537S 6,982 34525 B66539S 7,772 39030 B66541S 9,087 460
B2-1/2ZPLS 15
3600 Mechanical
Cast Iron
NPT
B54576 5,634 235(2-1/2 x 3 x 9 L) 20 B54092 6,824 345
25 B54093 7,325 39030 B54094 8,670 46015
Silicon Bronze
B66837S 5,792 23520 B66538S 6,982 34525 B66540S 7,486 39030 B66542S 8,830 460
B2-1/2ZPLS 15
3600 Mechanical Silicon Bronze Flanged
B75189 5,629 235(2-1/2 x 3 x 9 L) with Bronze Wear Ring
20 B75190 6,766 34525 B75191 7,250 39030 B75192 8,546 460
B2-1/2ZPM 2
1800 Packing
Cast Iron
NPT
B53802 4,529 (2-1/2 x 3 x 9 M) 3 B53803 4,869 B53806 4,671 160
5 B53804 5,780 B53807 4,936 1807.5 B53805 6,604 B53808 5,859 2202
Silicon Bronze
B74569 4,583 B74570 4,626 1253 B74585 4,931 B74586 4,763 1605 B74600 5,801 B74604 5,023 180
7.5 B74622 6,592 B74623 5,907 220B2-1/2ZPM 2
1800 Packing Silicon Bronze Flanged
B74574 4,583 B74575 4,626 125(2-1/2 x 3 x 9 M) 3 B74589 4,931 B74590 4,763 160
5 B74607 5,801 B74610 5,023 1807.5 B74626 6,592 B74627 5,907 220
B2-1/2ZPMS 2
1800 Mechanical Cast Iron NPT
B54577 4,140 B54581 4,131 125(2-1/2 x 3 x 9 M) 3 B54578 4,509 B54582 4,262 160
5 B54579 5,220 B54583 4,530 1807.5 B54580 6,050 B54584 5,235 220
B2-1/2ZPMS 2
1800 Mechanical Silicon Bronze
NPT
B74577 4,226 B74578 4,251 125(2-1/2 x 3 x 9 M) 3 B74592 4,581 B74593 4,373 160
5 B74612 5,257 B74614 4,628 1807.5 B74631 6,062 B74632 5,302 2202
Flanged
B74580 4,226 B74581 4,232 1253 B74595 4,581 B74596 4,373 1605 B74616 5,257 B74618 4,628 180
7.5 B74635 6,062 B74636 5,302 220
14 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® Z Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
9” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B3ZPL 20
3600 Packing
Cast Iron NPT
B51634 7,295 360(3 x 4 x 9 L) 25 B51635 7,785 405
30 B53818 9,177 47540 B53819 10,372 54050 B51638 11,717 62520
Cast Iron Flanged
B70206 7,295 36025 B70209 7,785 40530 B70212 9,177 47540 B70215 10,372 54050 B70218 11,717 62520
Silicon Bronze NPT
B66674S 7,481 36025 B66688S 7,896 40530 B66694S 9,330 47540 B66700S 10,533 54050 B66845S 11,868 62520
Silicon Bronze Flanged
B70181S 7,451 36025 B70184S 7,896 40530 B70187S 9,330 47540 B70190S 10,533 54050 B70193S 11,868 625
B3ZPLS 20
3600 Mechanical
Cast Iron NPT
B54112 7,137 360(3 x 4 x 9 L) 25 B54113 7,638 405
30 B54114 9,130 47540 B54115 10,364 54050 B54116 11,799 62520
Cast Iron Flanged
B70221 7,137 36025 B70224 7,638 40530 B70227 9,130 47540 B70230 10,364 54050 B70233 11,799 62520
Silicon Bronze NPT
B66675S 7,295 36025 B66689S 7,804 40530 B66695S 9,288 47540 B66701S 10,521 54050 B66847S 11,902 62520
Silicon Bronze Flanged
B70196S 7,295 36025 B70198S 7,804 40530 B70200S 9,288 47540 B70202S 10,521 54050 B70204S 11,902 625
CB1525P_CAN (03/01/17)15
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® Z Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
9” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B3ZPM 3
1800 Packing
Cast Iron NPT
B53820 4,908 B53823 4,887 180(3 x 4 x 9 M) 5 B53821 6,035 B53824 5,148 200
7.5 B53822 6,702 B53825 6,149 24010 B55579 7,480 B53826 6,486 24015 B51711 7,254 3203
Cast Iron Flanged
B70158 4,908 B70236 4,904 1805 B70159 6,035 B70237 5,148 200
7.5 B70163 6,702 B70239 6,149 24010 B70166 7,480 B70240 6,486 24015 B70241 7,254 3203
Silicon Bronze NPT
B66568S 5,069 B66569S 5,073 1805 B66580S 6,148 B66581S 5,313 200
7.5 B66590S 6,809 B66591S 6,340 24010 B66600S 7,624 B66601S 6,650 24015 B66608S 7,406 3203
Silicon Bronze Flanged
B71930S 4,858 B71931S 4,862 1805 B71932S 5,947 B71933S 5,092 200
7.5 B71934S 6,560 B71935S 6,049 24010 B71936S 7,306 B71937S 6,373 24015 B71939S 7,097 320
B3ZPMS 3
1800 Mechanical
Cast Iron NPT
B54599 4,725 B54603 4,524 180(3 x 4 x 9 M) 5 B54600 5,441 B54604 4,781 200
7.5 B54601 6,251 B54605 5,493 24010 B54652 7,182 B54606 5,826 24015 B54118 7,000 3203
Cast Iron Flanged
B70169 4,725 B70244 4,524 1805 B70172 5,441 B70245 4,781 200
7.5 B70175 6,251 B70247 5,493 24010 B70178 7,182 B70248 5,826 24015 B70249 7,000 3203
Silicon Bronze NPT
B66570S 4,872 B66571S 4,691 1805 B66582S 5,589 B66583S 4,949 200
7.5 B66592S 6,396 B66593S 5,651 24010 B66602S 7,328 B66603S 5,987 24015 B66609S 7,167 3163
Silicon Bronze Flanged
B71940S 4,645 B71941S 4,472 1805 B71942S 5,356 B71943S 4,743 200
7.5 B71944S 6,130 B71945S 5,416 24010 B71946S 7,022 B71947S 5,738 24015 B71949S 6,868 320
B3ZPBH 30
3600 Packing Cast Iron
NPT
B55588 9,424 490(3 x 4 x 9 BH) 40 B55589 10,640 555
50 B55541 12,292 64060 B55542 13,491 70530
Flanged
B70252 9,424 49040 B70255 10,640 55550 B70258 12,292 64060 B70260 13,491 705
16 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® Z Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
9” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B3ZPBHS 30
3600 Mechanical
Cast Iron NPT
B55543 9,431 490(3 x 4 x 9 BH) 40 B55544 10,668 555
50 B55545 12,356 64060 B55548 13,592 70575 B68423 16,914 87530
Cast Iron Flanged
B70263 9,431 49040 B70266 10,668 55550 B70269 12,356 64060 B70272 13,592 70575 B70275 16,914 87530
Silicon Bronze NPT
B77195 9,463 49040 B77198 10,644 55550 B77201 12,270 64060 B77204 13,446 70530
Silicon Bronze Flanged
B76758 9,463 49040 B76759 10,644 55550 B76760 12,270 64060 B76761 13,446 70575 B76762 16,631 875
B4ZPBH 7.51800 Packing Cast Iron Flanged
B85691 5,679 32015 B85687 6,522 40020 B85685 7,282 430
B4ZPBHS 7.5
1800 Mechanical Cast Iron Flanged
B85692MS1 B85692 5,428 320(4X5X9 BH) 10 B85690 5,687 350
15 B85688 6,264 40020 B85686 7,011 430
B5ZPBH 10
1800 Packing Cast Iron Flanged
B85701 6,713 335(5X6X9 BH) 15 B85699 7,313 365
20 B85697 8,088 41525 B85695 9,231 49030 B86081 10,478 535
B5ZPBHS 10
1800 Mechanical Cast Iron Flanged
B85702 6,432 335(5X6X9 BH) 15 B85700 7,022 365
20 B85698 7,787 41525 B85696 8,910 49030 B86082 10,139 535
B6ZPL 101800 Packing Cast Iron Flanged
B69509 8,480 B69512 7,599 295(6 x 8 x 9 L) 15 B69548 8,360 415
20 B69542 8,968 465B6ZPLS 10
1800 Mechanical
Cast Iron
Flanged
B69514 7,649 B69515 6,681 295(6 x 8 x 9 L) 15 B69546 8,038 415
20 B69540 8,649 46510 Silicon
Bronze
B76777 8,352 B76778 7,534 29515 B76779 8,837 41520 B76780 9,419 465
CB1525P_CAN (03/01/17)17
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® Z Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
9” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B6ZPH 15
1800 Packing Cast Iron Flanged
B69536 8,523 425(6 x 8 x 9 H) 20 B69531 9,119 475
25 B69520 10,204 54530 B69526 10,864 590
B6ZPHS 15
1800 Mechanical
Cast Iron
Flanged
B69535 8,111 425(6 x 8 x 9 H) 20 B69530 8,709 475
25 B69518 9,849 54530 B69525 10,508 59015
Silicon Bronze
B76781 8,903 42520 B76782 9,481 47525 B76783 10,575 54530 B76784 11,206 590
B6ZPBHH 20
1800 Packing Cast Iron Flanged
B85709 8,854 419(6X8X9 PBHH) 25 B85707 9,953 512
30 B85705 10,649 57340 B85703 11,902 647
B6ZPBHHS 20
1800 Mechanical Cast Iron Flanged
B85710 8,453 419(6X8X9 PBHH) 25 B85708 9,609 512
30 B85706 10,299 57340 B85704 11,520 647
NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required.Three phase motors used meet premium efficiency levels (NEMA MG 1-2011, Table 12-12, 20A or 20B).
18 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® E Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
10” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B1-1/2EPL 20 3600 Packing Silicon Bronze NPT B51598S $9,330 375
(1-1/2 x 2 x 10 L) 25 B51599S 9,843 420B1-1/2EPLS 20 3600 Mechanical Silicon
Bronze NPT B54078S 8,576 375(1-1/2 x 2 x 10 L) 25 B54079S 9,089 420B2EPBL 30
3600 Packing
Cast Iron NPT B53790 8,836 490(2 x 3 x 10 BL) 40 B53791 10,112 555
30 Silicon Bronze NPT B74329 8,107 490
40 B74333 9,903 55530 Silicon
Bronze Flanged B74496 8,615 49040 B74499 9,903 555
B2EPBLS 30
3600 Mechanical
Cast Iron NPT B54084 8,637 490(2 x 3 x 10 BL) 40 B54085 9,910 555
30 Cast Iron Flanged B76739 10,554 49040 B77339 11,773 55530 Silicon
Bronze NPT B74337 8,491 49040 B74341 9,713 55530 Silicon
Bronze Flanged B74502 8,491 49040 B74505 9,713 555
B2EPBHH 50 3600 Packing Cast Iron NPT B55841 11,489 630(2 x 3 x 10 BHH) 60 B55842 12,753 680B2EPBHHS 50
3600 Mechanical
Cast Iron NPT B55843 11,104 630(2 x 3 x 10 BHH) 60 B55844 12,356 680
50 Silicon Bronze NPT B77327 10,846 630
60 B66867S 12,578 68050 Silicon
Bronze Flanged B76791 13,882 63060 B76792 15,087 680
B3EPBL 40
3600 Packing Cast Iron NPT
B58054 12,620 570(3 x 4 x 10 BL) 50 B58055 14,322 655
60 B58056 15,545 70575 B58057 18,868 875
B3EPBLS 40
3600 Mechanical
Cast Iron NPT
B58058 12,676 570(3 x 4 x 10 BL) 50 B58059 14,370 655
60 B58060 15,597 70575 B60609 16,550 875
100 B77450 19,937 146050 Silicon
Bronze NPTB77189 13,996 655
60 B76743 15,169 70575 B77192 16,080 87550 Silicon
Bronze FlangedB76764 13,996 655
60 B76765 15,169 70575 B76766 16,080 875
B3EPM 5
1800 Packing Cast Iron NPT
B53828 6,381 230(3 x 4 x 10 M) with Bronze Wear Ring
8 B53829 7,176 10 B55580 7,853 B53832 6,874 27015 B51716 7,655 400
B3EPMS 5
1800 Mechanical Cast Iron NPT
B54607 5,662 B54610 5,038 230(3 x 4 x 10 M) with Bronze Wear Ring
8 B54608 6,498 B54611 5,763 27010 B54653 7,140 B54612 6,120 27015 B54125 7,372 400
CB1525P_CAN (03/01/17)19
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® E Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
10” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B4EPBM 40
3600 Packing Cast Iron Flanged
B58786 12,848 525(4 x 5 x 10 BM) 50 B58787 14,548 590
60 B58788 15,773 67575 B58789 18,969 725
100 B58790 22,137 895125 B58791 25,918 1,225
B4EPBMS 40
3600 Mechanical
Cast Iron
Flanged
B58792 12,341 525(4 x 5 x 10 BM) 50 B58793 14,040 590
60 B58794 15,262 67575 B62031 20,030 725
100 B61804 23,186 895125 B62032 26,963 1,22540
Silicon Bronze
B76769 12,305 52550 B76770 13,941 59060 B76425 15,110 67575 B76771 19,675 725
100 B76772 22,701 895125 B76773 26,322 1,225
B4EPM 15 1800 Packing Cast Iron Flanged B51726 9,335 455(4 x 5 x 10 M) 20 B51727 9,941 495B4EPMS 15 1800 Mechanical Cast Iron Flanged B54154 8,858 455(4 x 5 x 10 M) 20 B54155 9,462 495B5EPBM 60
3600 Packing Silicon Bronze Flanged
B56011S 18,024 1,025(5 x 6 x 10 BM) 75 B55984S 20,688 1,165
100 B55985S 21,531 1,275125 B55986S 25,404 1,400150 B55987S 28,821 1,575
B5EPBMS 60
3600 Mechanical Silicon Bronze Flanged
B56016S 17,180 1,025(5 x 6 x 10 BM) 75 B62093S 19,089 1,165
100 B62094S 22,306 1,275125 B62095S 26,254 1,400150 B62096S 28,042 1,575
B5EPH 151800 Packing Cast Iron Flanged
B66806 10,458 355(5 x 6 x 10 H) 20 B66812 11,070 360
25 B66818 12,471 370B5EPHS 15
1800 Mechanical
Cast Iron
Flanged
B66807 9,729 355(5 x 6 x 10 H) 20 B66813 10,342 360
25 B66819 11,454 37015 Silicon
Bronze
B76774 10,016 36520 B76775 10,606 37025 B76776 11,673 380
NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required.Three phase motors used meet premium efficiency levels (NEMA MG 1-2011, Table 12-12, 20A or 20B).
20 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® G Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
12” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B4GPBH 15
1800 Packing Silicon Bronze Flanged
B80470 $8,824 488(4 x 5 x 12 BH) 20 B80472 9,111 538
25 B80474 10,072 60330 B80476 10,911 64840 B80478 12,167 72850 B80480 13,008 788
B4GPBH 15
1800 Packing Silicon Bronze Flanged
B75868 9,192 508(4 x 6 x 12 BH) with 6” Suction
20 B75859 9,491 55825 B75858 10,491 62330 B75857 11,364 66840 B75856 12,676 74850 B75855 13,551 808
B4GPBHS 15
1800 Mechanical Silicon Bronze Flanged
B80482 9,188 488(4 x 5 x 12 BH) 20 B80484 9,475 538
25 B80486 10,436 60330 B80488 11,275 64840 B80490 12,533 72850 B80492 13,373 788
B4GPBHS 15
1800 Mechanical Silicon Bronze Flanged
B75869 9,570 508(4 x 6 x 12 BH) with 6” Suction
20 B75863 9,872 55825 B75862 10,871 62330 B75861 11,744 66840 B75860 13,054 74850 B75279 13,928 808
B8GPBM 40
1800 Packing Cast Iron Flanged
B51766 18,256 880(8 x 10 x 12 BM) 50 B51767 19,316 940
60 B55999 21,518 1,16575 B56000 23,050 1,235
100 B56001 25,866 1,820125 B75241 26,840 1,895
B8GPBMS 40
1800 Mechanical
Cast Iron
Flanged
B54231 17,535 880(8 x 10 x 12 BM) 50 B54232 18,422 940
60 B60625 20,380 1,16575 B60621 22,366 1,235
100 B61666 24,576 1,820125 B75242 25,767 1,89540
Silicon Bronze
B76785 18,072 88050 B76786 18,982 94060 B76787 21,003 1,16575 B76788 23,049 1,235
100 B76789 25,325 1,820125 B76790 27,704 1,895
B8GPBM 15
1200 Packing Cast Iron Flanged
B53863 14,091 745(8 x 10 x 12 BM) 20 B53864 18,722 815
25 B51798 19,251 89030 B51799 21,290 94040 B75255 22,421 1,120
CB1525P_CAN (03/01/17)21
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® G Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
12” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B8GPBMS 15
1200 Mechanical Cast Iron Flanged
B54227 18,479 745(8 x 10 x 12 BM) 20 B54228 19,934 815
25 B54229 20,463 89030 B54230 22,500 94040 B75257 22,981 1,120
B10GPBM 60
1800 Packing Cast Iron Flanged
B56007 24,306 1,170(10 x 12 x 12 BM) 75 B56008 25,292 1,240
100 B56009 28,290 1,820125 B56010 30,795 1,895
B10GPBMS 60
1800 Mechanical Cast Iron Flanged
B62106 25,029 1,170(10 x 12 x 12 BM) 75 B62107 26,044 1,240
100 B62108 29,115 1,820125 B62109 31,682 1,895
B10GPBM 20
1200 Packing Cast Iron Flanged
B53865 24,173 820(10 x 12 x 12 BM) 25 B50611 25,212 895
30 B50612 22,826 94540 B75261 35,763 1,124
B10GPBMS 20
1200 Mechanical Cast Iron Flanged
B54234 24,936 820(10 x 12 x 12 BM) 25 B54235 26,000 895
30 B54236 29,225 94540 B75263 36,659 1,124
Three phase motors used meet premium efficiency levels (NEMA MG 1-2011, Table 12-12, 20A or 20B).
22 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® J Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
13” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B2-1/2JPBM 15
1800 Packing
Cast Iron
NPT
B51693 $7,870 450(2-1/2 x 4 x 13 BM) 20 B51694 8,632 500
25 B53810 9,462 57015 Silicon
Bronze
B74656 7,979 45020 B74640 8,574 50025 B74644 9,459 570
B2-1/2JPBMS 15
1800 Mechanical
Cast Iron
NPT
B54104 6,993 450(2-1/2 x 4 x 13 BM) 20 B54105 7,685 500
25 B54106 9,125 57015 Silicon
Bronze
B74660 7,479 45020 B74652 8,070 50025 B74648 9,174 570
B3JPBL 15
1800 Packing
Cast Iron
NPT
B51717 8,223 455(3 x 4 x 13 BL) 20 B51718 8,840 505
25 B53833 9,827 57530 B53834 10,491 62015
Silicon Bronze
B74664 8,404 45520 B74668 8,995 50525 B74672 9,939 57530 B74676 10,579 620
B3JPBLS 15
1800 Mechanical
Cast Iron
NPT
B54130 11,243 455(3 x 4 x 13 BL) 20 B54131 11,243 505
25 B54132 9,479 57530 B54133 10,149 62015
Silicon Bronze
B74680 7,825 45520 B74684 8,416 50525 B74688 9,610 57530 B74692 10,250 620
B3JPBM 15
1800 Packing
Cast Iron
NPT
B51721 7,900 455(3 x 4 x 13 BM) 20 B51722 8,690 505
25 B53835 9,665 50530 B53836 10,372 57540 B51725 11,392 62015
Silicon Bronze
B74696 8,275 45520 B74700 8,853 50525 B74704 9,779 57530 B74708 10,416 62040 B74712 11,469 700
B3JPBMS 15
1800 Mechanical
Cast Iron
NPT
B54140 7,703 455(3 x 4 x 13 BM) 20 B54141 8,322 505
25 B54142 9,605 57530 B54143 10,272 62040 B54144 11,392 70015
Silicon Bronze
B74716 7,909 45520 B74720 8,497 50525 B74724 9,726 57530 B74728 10,371 62040 B74732 11,469 700
CB1525P_CAN (03/01/17)23
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® J Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
13” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B4JPBH 20
1800 Packing
Cast Iron
Flanged
B58872 10,811 540(4 x 5 x 13 BH) 25 B58873 11,978 605
30 B58874 12,600 65040 B58875 14,416 73050 B58876 15,406 79020
Silicon Bronze
B75871 10,513 54025 B75872 11,630 60530 B75873 12,235 65040 B75874 13,964 73050 B75875 14,918 790
B4JPBHS 20
1800 Mechanical
Cast Iron
Flanged
B58877 10,534 540(4 x 5 x 13 BH) 25 B58878 11,955 605
30 B58879 12,618 65040 B58880 14,487 79050 B58881 15,524 85020
Silicon Bronze
B75876 10,249 54025 B75877 11,610 60530 B75878 12,243 65040 B75879 14,041 79050 B75880 15,028 850
B4JPBHH 60 1800 Packing Cast Iron Flanged B55974 18,693 855(4 x 6 x 13 BHH)B4JPBHHS 60 1800 Mechanical Cast Iron Flanged B62036 18,110 855(4 x 6 x 13 BHH)B6JPBL 25
1800 Packing Cast Iron Flanged
B53858 12,948 670(6 x 8 x 13 BL) 30 B53859 13,616 715
40 B51759 15,545 79550 B51760 16,599 855
B6JPBLS 25
1800 Mechanical Cast Iron Flanged
B54214 12,502 670(6 x 8 x 13 BL) 30 B54215 13,172 715
40 B54216 15,062 79550 B54217 16,146 855
B6JPBM 30
1800 Packing Cast Iron Flanged
B58126 13,484 720(6 x 8 x 13 BM) 40 B56761 15,368 800
50 B56762 16,390 86060 B58127 19,148 1,08575 B58128 20,804 1,155
24 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® J Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
13” – Nominal Impeller Diameter
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B6JPBM 30
1800 Packing Silicon Bronze Flanged
B74909 14,017 720(6 x 8 x 13 BM) 40 B74913 15,829 800
50 B74917 16,818 86060 B74921 19,278 1,08575 B74925 20,976 1,155
B6JPBMS 30
1800 Mechanical
Cast Iron
Flanged
B56768 13,346 720(6 x 8 x 13 BM) 40 B56769 15,264 800
50 B56770 16,323 86060 B62097 17,723 1,08575 B08201 19,242 1,15530
Silicon Bronze
B74941 13,828 72040 B74945 15,676 79950 B74949 16,681 86060 B74953 18,026 1,08575 B74955 19,479 1,155
B6JPBM 10
1200 Packing
Cast Iron
Flanged
B56757 13,260 590(6 x 8 x 13 BM) 15 B58124 15,022 665
20 B58125 15,861 73510 Silicon
Bronze
B74897 13,749 59015 B74901 15,494 66520 B74905 16,149 735
B6JPBMS 10
1200 Mechanical
Cast Iron
Flanged
(6 x 8 x 13 BM) 15 B56766 14,552 66520 B56767 15,785 73510 Silicon
Bronze 15 B74933 14,983 66520 B74937 15,545 735
B6JPBH 75 1800 Packing Cast Iron Flanged B58301 21,891 1,155(6 x 8 x 13 BH) 100 B58439 24,972 1,355B6JPBHS 75 1800 Mechanical Cast Iron Flanged B08193 21,435 1,155(6 x 8 x 13 BH) 100 B62098 24,468 1,355B8JPBH 60
1800 Packing Cast Iron Flanged
B85776 23,195 1170(8x10x13 PBH) 75 B85774 24,756 1240
100 B85772 27,947 1410125 B85770 30,634 1820150 B85768 34,571 2100
B8JPBHS 60
1800 Mechanical Cast Iron Flanged
B85777 23,700 1170(8x10x13 PBH) 75 B85775 24,783 1240
100 B85773 28,590 1410125 B85771 29,736 1820150 B85769 35,108 2100
B10JPBH 100
1800 Packing Cast Iron Flanged
B85764 28,680 1820(10x12x13 PBH) 125 B85762 30,965 1895
150 B85760 35,068 1930200 B85758 42,392 2250
B10JPBHS 100
1800 Mechanical Cast Iron Flanged
B85765 29,694 1820(10x12x13 PBH) 125 B85763 31,979 1895
150 B85761 36,083 1930200 B85759 43,016 2250
NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required.Three phase motors used meet premium efficiency levels (NEMA MG 1-2011, Table 12-12, 20A or 20B).
CB1525P_CAN (03/01/17)25
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® EX Series Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
15” – Nominal Impeller Diameters
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B4EXPBL 60 1800 Packing Cast Iron Flanged B55975 $23,640 1,060(4 x 5 x 15 BL) 75 B55976 25,341 1,130B5EXPBH 100 1800 Packing Cast Iron Flanged B55988 28,805 1,265(5 x 6 x 15 BH) 125 B55989 31,386 1,475B6EXPBL 75 1800 Packing Cast Iron Flanged B55994 25,605 1,065(6 x 8 x 15 BL) 100 B55995 28,638 1,265B6EXPBLS 75 1800 Mechanical Cast Iron Flanged B68434 27,824 1,065(6 x 8 x 15 BL) 100 B68436 30,564 1,265B6EXPBH 75
1800 Packing Cast Iron Flanged
B58129 25,986 1,065(6 x 8 x 15 BH) 100 B58130 29,014 1,265
125 B58131 30,754 1,335150 B56803 35,144 1,410200 B56804 40,654 1,570
B6EXPBHS 75
1800 Mechanical Cast Iron Flanged
B68438 28,083 1,065(6 x 8 x 15 BH) 100 B68440 31,114 1,265
125 B68442 32,658 1,335150 B62103 37,786 1,410200 B62104 43,162 1,570
Berkeley® EY Series18” – Nominal Impeller Diameters
Model Number (Size) HP RPM Shaft Seal
Impeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number
List Price
Catalog Number
List Price
B4EYPBM 40
1800 Packing Cast Iron Flanged
B83191 16,146 965(4 x 5 x 18 BM) 50 B83195 20,411 1,025
60 B83192 23,030 1,25075 B83193 24,681 1,320
100 B83188 27,658 1,810B4EYPBMS 40
1800 Mechanical Cast Iron Flanged
B83186 18,450 965(4 x 5 x 18 BM) 50 B83187 19,473 1,025
60 B83194 22,194 1,25075 B83189 24,268 1,320
100 B83190 27,179 1,810B4EYPBH 100 1800 Packing Cast Iron Flanged B83196 26,770 1,810(4 x 5 x 18 BH) 125 B83197 29,160 1,962
NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required.Three phase motors used meet premium efficiency levels (NEMA MG 1-2011, Table 12-12, 20A or 20B).
26 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Berkeley® Electric Motor Drive
When ordering 575 volt product, please add -575T to the 3 phase base part number (i.e. B54488S would become B54488S-575T)3-30hp 575V pumps will be provided with TEFC motors at no additional charge40 – 200hp will be subject to additional charges for TEFC motors (Please Consult Factory)
Self-Priming
Model Number
(Size) HP RPM Shaft SealImpeller Material
Volute Connection
ODP 1 Phase ODP 3 PhaseWeight (Lbs.)
Catalog Number List Price
Catalog Number List Price
B2XPKS 1-1/23600 Mechanical Cast Iron NPT
B51499 $2,355 B51502 $2,714 91(2 x 2 x 5) 2 B51500 2,536 B51503 2,890 95
3 B51501 2,915 98B3TPKS 10 3600
Mechanical Cast Iron NPT
B60767 5,764 B60768 5,234 220(3 x 3 x 6) 15 B60769 5,771 329
1-1/21800
B60761 3,831 B60762 3,992 1322 B60763 3,956 B60764 4,050 1773 B60765 4,323 B60766 4,199 190
B4TPKLS 3 1800 Mechanical Cast Iron NPT B54629 6,011 B54630 6,149 185(4 x 4 x 6 L)B4TPKHS 5 1800 Mechanical Cast Iron NPT B54631 6,686 B54632 6,513 196(4 x 4 x 6 H)B4ZPKS 5
1800 Mechanical Cast Iron NPTB58449 6,730 B58450 6,560 370
(4 x 4 x 9) 7-1/2 B54633 7,557 B54634 7,146 35010 B54635 8,189 B54636 7,511 423
NOTE: See page 4 for model description.Three phase motors used meet premium efficiency levels (NEMA MG 1-2011, Table 12-12, 20A or 20B).
Berkeley® Electric Motor Drive
Seal Adders
RPM Range
Horsepower Range Viton EPDM
Sil-Carbide/Viton
1200 1-50 HP $71 $71 $171 1200 60-125 HP 105 105 3551800 1-50 HP 71 71 1711800 60-125 HP 105 105 3553600 5-60 HP 71 71 1713600 75-150 HP 105 105 355
Seal adders are for Berkeley® B-Line electric closed coupled pumps only. Please note, standard Berkeley Pumps are designed for pumping water only. Always check chemical compatibility charts when pumping solutions other than water.Consult factory for additional seal options and lead times.EPDM seals use standard carbon/ceramic rotating and stationary faces with 316 stainless steel compression spring. The operating temperature range is from -50° F to 300° F, EPDM seals are not compatible with petroleum products.Viton seals use standard carbon/ceramic rotating and stationary faces with 316 stainless steel compression spring. The operating temperature range is from -10° F to 400° F. Viton seals have a wider range of chemical compatibility than standard BUNA or EPDM seals.Sil-Car/Viton seals use an extremely durable silicon carbide material on both the stationary and rotating faces. Elastomers are Viton, 316 stainless compression spring. The operating temperature is from -10° F to 400° F.
CB1525P_CAN (03/01/17)27
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Close Coupled Pump Motors
Note: Single phase motors are standard efficiency. Three phase motors are premium efficiency.
PRODUCT LIST
NO. PH VOLTS PRICE
PRODUIT PRIX
SINGLE PHASE 208/230 VOLT MONOPHASÉ 208/230 VOLT
26295A0103 1½ 1 208/230 143JM TEFC 52/24 $1,122.00
26295A0105 2 1 208/230 145JM TEFC 52/24 $1,184.00
26295A0107 3 1 208/230 145JM TEFC 52/24 $1,283.00
26295A0109 5 1 208/230 184JM TEFC 99/45 $1,866.00
26295A0111 7½ 1 208/230 213JM TEFC 141/64 $2,826.00
26295A0113 10 1 208/230 215JM TEFC 163/74 $2,956.00
THREE PHASE 208/230/460 VOLT TROIS PHASE 208/230/460 VOLT
26296A0603 1½ 3 208/230/460 145JM TEFC 52/24 $946.00
26296A0605 2 3 208/230/460 145JM TEFC 52/24 $994.00
26296A0624 3 3 208/230/460 182JM TEFC 52/24 $1,119.00
26296A0609 5 3 208/230/460 184JM TEFC 99/45 $1,420.00
26296A0625 7½ 3 208/230/460 215JM TEFC 99/45 $1,777.00
26296A0613 10 3 208/230/460 215JM TEFC 163/74 $2,042.00
26296A0626 15 3 208/230/460 254JM TEFC 163/74 $2,952.00
26296A0617 20 3 208/230/460 256JM TEFC 253/115 $3,283.00
26296A0627 25 3 208/230/460 284JM TEFC 302/137 $4,241.00
26296A0621 30 3 208/230/460 286JM TEFC 375/170 $4,537.00
26296A0635 40 3 208/230/460 324JM TEFC 403/183 $4,987.00
26296A0637 50 3 208/230/460 326JM TEFC 573/260 $6,921.00
26296A0639 60 3 208/230/460 364JM TEFC 595/270 $9,662.00
THREE PHASE 575 VOLT TROIS PHASE 575 VOLT
26296A0803 1½ 3 575 145JM TEFC 52/24 $946.00
26296A0805 2 3 575 145JM TEFC 52/24 $994.00
26296A0824 3 3 575 182JM TEFC 52/24 $1,119.00
26296A0809 5 3 575 184JM TEFC 99/45 $1,420.00
26296A0825 7½ 3 575 215JM TEFC 99/45 $1,777.00
26296A0813 10 3 575 215JM TEFC 163/74 $2,042.00
26296A0826 15 3 575 254JM TEFC 163/74 $2,952.00
26296A0817 20 3 575 256JM TEFC 253/115 $3,283.00
26296A0827 25 3 575 284JM TEFC 302/137 $4,241.00
26296A0821 30 3 575 286JM TEFC 375/170 $4,537.00
26296A0835 40 3 575 324JM TEFC 403/183 $4,987.00
26296A0837 50 3 575 326JM TEFC 573/260 $6,921.00
26296A0839 60 3 575 364JM TEFC 595/270 $9,662.00
HP
CV
FRAME
CADRE
ENCLOSURE
CONTOUR
WT/PDS
LB/KG
3600 RPM
28 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Close Coupled Pump Motors
Note: Single phase motors are standard efficiency. Three phase motors are premium efficiency.
PRODUCT LIST
NO. PH VOLTS PRICE
PRODUIT PRIX
SINGLE PHASE 208/230 VOLT MONOPHASÉ 208/230 VOLT
26295A0100 1 1 208/230 143JM TEFC 52/24 $989.00
26295A0102 1½ 1 208/230 145JM TEFC 52/24 $1,144.00
26295A0104 2 1 208/230 145JM TEFC 52/24 $1,177.00
26295A0106 3 1 208/230 184JM TEFC 99/45 $1,578.00
26295A0108 5 1 208/230 213JM TEFC 99/45 $1,921.00
26295A0110 7½ 1 208/230 215JM TEFC 141/64 $2,722.00
26295A0112 10 1 208/230 215JM TEFC 163/74 $2,888.00
THREE PHASE 208/230/460 VOLT TROIS PHASE 208/230/460 VOLT
26296A0401 1 3 208/230/460 143JM TEFC 52/24 $872.00
26296A0402 1½ 3 208/230/460 145JM TEFC 52/24 $946.00
26296A0404 2 3 208/230/460 145JM TEFC 52/24 $967.00
26296A0406 3 3 208/230/460 182JM TEFC 82/37 $1,110.00
26296A0408 5 3 208/230/460 184JM TEFC 99/45 $1,420.00
26296A0410 7½ 3 208/230/460 213JM TEFC 141/64 $1,447.00
26296A0412 10 3 208/230/460 215JM TEFC 163/74 $1,740.00
26296A0414 15 3 208/230/460 254JM TEFC 253/115 $2,224.00
26296A0416 20 3 208/230/460 256JM TEFC 302/137 $2,739.00
26296A0418 25 3 208/230/460 284JM TEFC 375/170 $4,334.00
26296A0420 30 3 208/230/460 286JM TEFC 403/183 $4,855.00
26296A0422 40 3 208/230/460 324JM TEFC 573/260 $6,066.00
26296A0426 50 3 208/230/460 326JM TEFC 595/270 $7,735.00
THREE PHASE 575 VOLT TROIS PHASE 575 VOLT
26296A0701 1 3 575 143JM TEFC 52/24 $872.00
26296A0702 1½ 3 575 145JM TEFC 52/24 $946.00
26296A0704 2 3 575 145JM TEFC 52/24 $967.00
26296A0706 3 3 575 182JM TEFC 82/37 $1,110.00
26296A0708 5 3 575 184JM TEFC 99/45 $1,420.00
26296A0710 7½ 3 575 213JM TEFC 141/64 $1,447.00
26296A0712 10 3 575 215JM TEFC 163/74 $1,740.00
26296A0714 15 3 575 254JM TEFC 253/115 $2,224.00
26296A0716 20 3 575 256JM TEFC 302/137 $2,739.00
26296A0718 25 3 575 284JM TEFC 375/170 $4,334.00
26296A0720 30 3 575 286JM TEFC 403/183 $4,855.00
26296A0722 40 3 575 324JM TEFC 573/260 $6,066.00
26296A0726 50 3 575 326JM TEFC 595/270 $7,735.00
HP
CV
FRAME
CADRE
ENCLOSURE
CONTOUR
WT/PDS
LB/KG
1800 RPM
CB1525P_CAN (03/01/17)29
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Close Coupled Pump Motors
PRODUCT LIST
NO. PH VOLTS PRICE
PRODUIT PRIX
THREE PHASE 208/230/460 VOLT TROIS PHASE 208/230/460 VOLT
26296A0501 1 3 208/230/460 145JM TEFC 61/28 $905.00
26296A0503 1½ 3 208/230/460 182JM TEFC 95/43 $1,050.00
26296A0505 2 3 208/230/460 184JM TEFC 112/51 $1,261.00
26296A0507 3 3 208/230/460 213JM TEFC 175/80 $1,463.00
26296A0509 5 3 208/230/460 215JM TEFC 204/93 $1,943.00
26296A0511 7½ 3 208/230/460 254JM TEFC 292/133 $3,087.00
26296A0513 10 3 208/230/460 256JM TEFC 322/146 $3,472.00
26296A0515 15 3 208/230/460 284JM TEFC 360/164 P.O.A.
26296A0517 20 3 208/230/460 286JM TEFC 428/195 P.O.A.
26296A0519 25 3 208/230/460 324JM TEFC 591/269 P.O.A.
26296A0521 30 3 208/230/460 326JM TEFC 648/295 P.O.A.
THREE PHASE 575 VOLT TROIS PHASE 575 VOLT
26296A0901 1 3 575 145JM TEFC 61/28 $905.00
26296A0903 1½ 3 575 182JM TEFC 95/43 $1,050.00
26296A0905 2 3 575 184JM TEFC 112/51 $1,261.00
26296A0907 3 3 575 213JM TEFC 175/80 $1,463.00
26296A0909 5 3 575 215JM TEFC 204/93 $1,943.00
26296A0911 7½ 3 575 254JM TEFC 292/133 $3,087.00
26296A0913 10 3 575 256JM TEFC 322/146 $3,472.00
26296A0915 15 3 575 284JM TEFC 360/164 P.O.A.
26296A0917 20 3 575 286JM TEFC 428/195 P.O.A.
26296A0919 25 3 575 324JM TEFC 591/269 P.O.A.
26296A0921 30 3 575 326JM TEFC 648/295 P.O.A.
HP
CV
FRAME
CADRE
ENCLOSURE
CONTOUR
WT/PDS
LB/KG
Note: Single phase motors are standard efficiency. Three phase motors are premium efficiency.
1200 RPM
30 CB1525P_CAN (03/01/17)
VARIABLE FREQUENCY DRIVES
Pentek Intellidrive™ XL Pump Controller
Single Phase Input Drives
Output Amps Input Voltage Input Phase NEMA Rating Model Number List Price Weight24.2 230 1
NEMA 1
PID007512ND $5,868 5130.8 230 1 PID010012ND 6,916 6059.4 230 1 PID020012ND 13,056 9988 230 1 PID030012ND 18,113 143
24.2 230 1
NEMA 3R
PID007532ND 6,810 5130.8 230 1 PID010032ND 7,874 6059.4 230 1 PID020032ND 14,617 9988 230 1 PID030032ND 19,167 143
24.2 230 1
NEMA 4X
PID007542ND 10,477 5130.8 230 1 PID010042ND 12,349 6059.4 230 1 PID020042ND 24,267 9988 230 1 PID030042ND 39,090 143
CB1525P_CAN (03/01/17)31
VARIABLE FREQUENCY DRIVES
NEMA 1 Enclosure - No DisconnectOutput Amps Input Voltage Input Phase Model Number List Price Weight
4.6 230 3 PID001013ND $1,667 317.5 230 3 PID002013ND 1,859 31
10.6 230 3 PID003013ND 1,962 3116.7 230 3 PID005013ND 2,335 3124.2 230 3 PID007513ND 2,930 5130.8 230 3 PID010013ND 3,396 6046.2 230 3 PID015013ND 4,575 3059.4 230 3 PID020013ND 5,606 6074.8 230 3 PID025013ND 7,203 9988 230 3 PID030013ND 8,536 99
115 230 3 PID040013ND 10,820 99143 230 3 PID050013ND 12,147 143170 230 3 PID060013ND 14,585 1432.1 460 3 PID001014ND 1,545 123.4 460 3 PID002014ND 1,656 124.8 460 3 PID003014ND 1,804 128.2 460 3 PID005014ND 2,106 1211 460 3 PID007514ND 2,374 17
14.5 460 3 PID010014ND 2,814 1721 460 3 PID015014ND 3,667 5127 460 3 PID020014ND 4,618 5134 460 3 PID025014ND 5,960 5140 460 3 PID030014ND 7,040 6052 460 3 PID040014ND 8,529 6065 460 3 PID050014ND 10,838 9980 460 3 PID060014ND 12,654 99
105 460 3 PID075014ND 14,159 99130 460 3 PID100014ND 17,189 143160 460 3 PID125014ND 20,641 1431.7 575 3 PID001015ND 2,729 172.7 575 3 PID002015ND 2,788 173.9 575 3 PID003015ND 2,906 176.1 575 3 PID005015ND 2,993 179 575 3 PID007515ND 3,274 17
11 575 3 PID010015ND 3,725 1718 575 3 PID015015ND 4,845 5122 575 3 PID020015ND 6,100 5127 575 3 PID025015ND 7,880 5134 575 3 PID030015ND 9,309 6041 575 3 PID040015ND 11,276 6052 575 3 PID050015ND 14,329 9962 575 3 PID060015ND 16,734 9983 575 3 PID075015ND 18,722 99
100 575 3 PID100015ND 22,728 143131 575 3 PID125015ND 27,305 143
Pentek Intellidrive™ XL Pump Controller
32 CB1525P_CAN (03/01/17)
VARIABLE FREQUENCY DRIVES
NEMA 1 Enclosure - Fused Disconnect
Output Amps Input Voltage Input Phase Model Number List Price Weight4.6 230 3 PID001013FD $2,996 157.5 230 3 PID002013FD 3,348 15
10.6 230 3 PID003013FD 3,527 1516.7 230 3 PID005013FD 3,968 1924.2 230 3 PID007513FD 4,605 5130.8 230 3 PID010013FD 5,301 6046.2 230 3 PID015013FD 6,638 3059.4 230 3 PID020013FD 7,813 6074.8 230 3 PID025013FD 9,811 9988 230 3 PID030013FD 11,631 99
115 230 3 PID040013FD 14,741 99143 230 3 PID050013FD 16,276 143170 230 3 PID060013FD 19,081 1432.1 460 3 PID001014FD 2,771 313.4 460 3 PID002014FD 2,986 314.8 460 3 PID003014FD 3,255 318.2 460 3 PID005014FD 3,582 3111 460 3 PID007514FD 3,855 31
14.5 460 3 PID010014FD 4,295 3121 460 3 PID015014FD 5,594 5127 460 3 PID020014FD 6,790 5134 460 3 PID025014FD 8,318 5140 460 3 PID030014FD 9,519 6052 460 3 PID040014FD 11,162 6065 460 3 PID050014FD 14,177 9980 460 3 PID060014FD 16,544 99
105 460 3 PID075014FD 18,517 99130 460 3 PID100014FD 22,477 143160 460 3 PID125014FD 26,997 1431.7 575 3 PID001015FD 3,324 192.7 575 3 PID002015FD 3,431 193.9 575 3 PID003015FD 3,742 196.1 575 3 PID005015FD 4,123 199 575 3 PID007515FD 4,369 19
11 575 3 PID010015FD 4,880 1918 575 3 PID015015FD 6,435 5122 575 3 PID020015FD 7,816 5127 575 3 PID025015FD 9,558 5134 575 3 PID030015FD 10,944 6041 575 3 PID040015FD 12,825 6052 575 3 PID050015FD 16,290 9962 575 3 PID060015FD 19,031 9983 575 3 PID075015FD 21,291 99
100 575 3 PID100015FD 25,845 143131 575 3 PID125015FD 31,050 143
Pentek Intellidrive™ XL Pump Controller
CB1525P_CAN (03/01/17)33
VARIABLE FREQUENCY DRIVES
NEMA 3R Enclosure - No Disconnect
Output Amps Input Voltage Input Phase Model Number List Price Weight4.6 230 3 PID001033ND $2,251 317.5 230 3 PID002033ND 2,497 31
10.6 230 3 PID003033ND 2,628 3116.7 230 3 PID005033ND 3,118 3124.2 230 3 PID007533ND 3,658 5130.8 230 3 PID010033ND 4,297 6046.2 230 3 PID015033ND 5,615 3059.4 230 3 PID020033ND 6,688 6074.8 230 3 PID025033ND 8,365 9988 230 3 PID030033ND 9,887 99
115 230 3 PID040033ND 12,203 99143 230 3 PID050033ND 13,685 143170 230 3 PID060033ND 16,417 1432.1 460 3 PID001034ND 2,096 243.4 460 3 PID002034ND 2,243 244.8 460 3 PID003034ND 2,432 248.2 460 3 PID005034ND 2,825 2411 460 3 PID007534ND 3,168 31
14.5 460 3 PID010034ND 3,658 3121 460 3 PID015034ND 4,625 5127 460 3 PID020034ND 5,671 5134 460 3 PID025034ND 7,120 5140 460 3 PID030034ND 8,176 6052 460 3 PID040034ND 9,896 6065 460 3 PID050034ND 12,212 9980 460 3 PID060034ND 14,257 99
105 460 3 PID075034ND 15,945 99130 460 3 PID100034ND 19,332 143160 460 3 PID125034ND 23,203 1431.7 575 3 PID001035ND 2,889 312.7 575 3 PID002035ND 2,947 313.9 575 3 PID003035ND 3,201 316.1 575 3 PID005035ND 3,717 319 575 3 PID007535ND 4,169 31
11 575 3 PID010035ND 4,820 3118 575 3 PID015035ND 6,100 5122 575 3 PID020035ND 7,473 5127 575 3 PID025035ND 9,393 5134 575 3 PID030035ND 10,795 6041 575 3 PID040035ND 12,866 6052 575 3 PID050035ND 16,141 9962 575 3 PID060035ND 18,833 9983 575 3 PID075035ND 21,064 99
100 575 3 PID100035ND 25,544 143131 575 3 PID125035ND 30,674 143
Pentek Intellidrive™ XL Pump Controller
34 CB1525P_CAN (03/01/17)
VARIABLE FREQUENCY DRIVES
NEMA 3R Enclosure - Fused Disconnect
Output Amps Input Voltage Input Phase Model Number List Price Weight4.6 230 3 PID001033FD $3,353 317.5 230 3 PID002033FD 3,746 31
10.6 230 3 PID003033FD 3,951 3116.7 230 3 PID005033FD 4,443 3124.2 230 3 PID007533FD 4,982 5130.8 230 3 PID010033FD 5,622 6046.2 230 3 PID015033FD 6,938 3059.4 230 3 PID020033FD 8,029 6074.8 230 3 PID025033FD 10,084 9988 230 3 PID030033FD 11,942 99
115 230 3 PID040033FD 15,144 99143 230 3 PID050033FD 16,728 143170 230 3 PID060033FD 19,607 1432.1 460 3 PID001034FD 3,127 313.4 460 3 PID002034FD 3,349 314.8 460 3 PID003034FD 3,621 318.2 460 3 PID005034FD 4,014 3111 460 3 PID007534FD 4,358 31
14.5 460 3 PID010034FD 4,847 3121 460 3 PID015034FD 5,816 5127 460 3 PID020034FD 6,985 5134 460 3 PID025034FD 8,539 5140 460 3 PID030034FD 9,778 6052 460 3 PID040034FD 11,498 6065 460 3 PID050034FD 14,561 9980 460 3 PID060034FD 17,004 99
105 460 3 PID075034FD 19,027 99130 460 3 PID100034FD 23,096 143160 460 3 PID125034FD 27,745 1431.7 575 3 PID001035FD 3,792 312.7 575 3 PID002035FD 3,847 313.9 575 3 PID003035FD 4,187 316.1 575 3 PID005035FD 4,637 319 575 3 PID007535FD 5,030 31
11 575 3 PID010035FD 5,594 3118 575 3 PID015035FD 6,729 5122 575 3 PID020035FD 8,026 5127 575 3 PID025035FD 9,831 5134 575 3 PID030035FD 11,242 6041 575 3 PID040035FD 13,186 6052 575 3 PID050035FD 16,744 9962 575 3 PID060035FD 19,560 9983 575 3 PID075035FD 21,880 99
100 575 3 PID100035FD 26,561 143131 575 3 PID125035FD 31,907 143
Pentek Intellidrive™ XL Pump Controller
CB1525P_CAN (03/01/17)35
VARIABLE FREQUENCY DRIVES
NEMA 4X Enclosure - No Disconnect
Output Amps Input Voltage Input Phase Model Number List Price Weight4.6 230 3 PID001043ND $3,602 317.5 230 3 PID002043ND 3,970 31
10.6 230 3 PID003043ND 4,199 3116.7 230 3 PID005043ND 4,715 3124.2 230 3 PID007543ND 5,525 5130.8 230 3 PID010043ND 6,277 6046.2 230 3 PID015043ND 7,538 3059.4 230 3 PID020043ND 9,191 6074.8 230 3 PID025043ND 11,394 9988 230 3 PID030043ND 13,719 99
115 230 3 PID040043ND 17,015 99143 230 3 PID050043ND 20,026 143170 230 3 PID060043ND 24,095 1432.1 460 3 PID001044ND 3,708 243.4 460 3 PID002044ND 3,929 244.8 460 3 PID003044ND 4,225 248.2 460 3 PID005044ND 4,625 2411 460 3 PID007544ND 4,960 31
14.5 460 3 PID010044ND 5,509 3121 460 3 PID015044ND 6,997 5127 460 3 PID020044ND 8,095 5134 460 3 PID025044ND 10,132 5140 460 3 PID030044ND 12,064 6052 460 3 PID040044ND 14,184 6065 460 3 PID050044ND 18,170 9980 460 3 PID060044ND 21,074 99
105 460 3 PID075044ND 23,702 99130 460 3 PID100044ND 28,768 143160 460 3 PID125044ND 33,074 1431.7 575 3 PID001045ND 3,970 312.7 575 3 PID002045ND 4,182 313.9 575 3 PID003045ND 4,494 316.1 575 3 PID005045ND 4,944 319 575 3 PID007545ND 5,313 31
11 575 3 PID010045ND 5,933 3118 575 3 PID015045ND 7,538 5122 575 3 PID020045ND 8,791 5127 575 3 PID025045ND 11,024 5134 575 3 PID030045ND 13,120 6041 575 3 PID040045ND 15,461 6052 575 3 PID050045ND 19,552 9962 575 3 PID060045ND 23,269 9983 575 3 PID075045ND 26,068 99
100 575 3 PID100045ND 31,346 143131 575 3 PID125045ND 36,273 143
Pentek Intellidrive™ XL Pump Controller
36 CB1525P_CAN (03/01/17)
VARIABLE FREQUENCY DRIVES
NEMA 4X Enclosure - Fused Disconnect
Output Amps Input Voltage Input Phase Model Number List Price Weight4.6 230 3 PID001043FD $6,304 317.5 230 3 PID002043FD 6,740 31
10.6 230 3 PID003043FD 7,061 3116.7 230 3 PID005043FD 7,715 3124.2 230 3 PID007543FD 8,181 5130.8 230 3 PID010043FD 9,127 6046.2 230 3 PID015043FD 10,735 3059.4 230 3 PID020043FD 12,624 6074.8 230 3 PID025043FD 15,465 9988 230 3 PID030043FD 18,014 99
115 230 3 PID040043FD 24,786 99143 230 3 PID050043FD 31,642 143170 230 3 PID060043FD 39,593 1432.1 460 3 PID001044FD 6,076 313.4 460 3 PID002044FD 6,358 314.8 460 3 PID003044FD 6,733 318.2 460 3 PID005044FD 7,156 3111 460 3 PID007544FD 7,437 31
14.5 460 3 PID010044FD 7,960 3121 460 3 PID015044FD 8,981 5127 460 3 PID020044FD 10,232 5134 460 3 PID025044FD 11,830 5140 460 3 PID030044FD 13,559 6052 460 3 PID040044FD 15,684 6065 460 3 PID050044FD 19,440 9980 460 3 PID060044FD 22,479 99
105 460 3 PID075044FD 25,280 99130 460 3 PID100044FD 33,022 143160 460 3 PID125044FD 41,970 1431.7 575 3 PID001045FD 6,680 312.7 575 3 PID002045FD 6,719 313.9 575 3 PID003045FD 7,250 316.1 575 3 PID005045FD 7,745 319 575 3 PID007545FD 8,053 31
11 575 3 PID010045FD 8,628 3118 575 3 PID015045FD 9,774 5122 575 3 PID020045FD 11,189 5127 575 3 PID025045FD 13,017 5134 575 3 PID030045FD 14,916 6041 575 3 PID040045FD 17,219 6052 575 3 PID050045FD 21,420 9962 575 3 PID060045FD 24,796 9983 575 3 PID075045FD 27,848 99
100 575 3 PID100045FD 35,469 143131 575 3 PID125045FD 44,083 143
Pentek Intellidrive™ XL Pump Controller
CB1525P_CAN (03/01/17)37
VARIABLE FREQUENCY DRIVES
Open Chassis (IP20) - No Disconnect
Output Amps Input Voltage Input Phase Model Number List Price Weight4.6 230 3 PID001003ND $1,466 117.5 230 3 PID002003ND 1,580 11
10.6 230 3 PID003003ND 1,696 1116.7 230 3 PID005003ND 1,990 1524.2 230 3 PID007503ND 2,424 5130.8 230 3 PID010003ND 2,890 6046.2 230 3 PID015003ND 3,890 3059.4 230 3 PID020003ND 4,765 6074.8 230 3 PID025003ND 6,123 9988 230 3 PID030003ND 7,253 99
115 230 3 PID040003ND 9,201 99143 230 3 PID050003ND 10,330 143170 230 3 PID060003ND 12,401 1432.1 460 3 PID001004ND 1,318 113.4 460 3 PID002004ND 1,410 114.8 460 3 PID003004ND 1,541 118.2 460 3 PID005004ND 1,794 1111 460 3 PID007504ND 2,015 15
14.5 460 3 PID010004ND 2,398 1521 460 3 PID015004ND 3,118 3027 460 3 PID020004ND 3,929 3034 460 3 PID025004ND 5,068 3040 460 3 PID030004ND 5,985 5352 460 3 PID040004ND 7,243 5365 460 3 PID050004ND 9,207 5380 460 3 PID060004ND 10,756 77
105 460 3 PID075004ND 12,033 77130 460 3 PID100004ND 14,602 110160 460 3 PID125004ND 17,548 1101.7 575 3 PID001005ND 2,503 152.7 575 3 PID002005ND 2,565 153.9 575 3 PID003005ND 2,693 156.1 575 3 PID005005ND 2,789 159 575 3 PID007505ND 3,244 15
11 575 3 PID010005ND 3,575 1518 575 3 PID015005ND 4,661 3022 575 3 PID020005ND 5,864 3027 575 3 PID025005ND 7,567 3034 575 3 PID030005ND 8,948 5341 575 3 PID040005ND 10,843 5352 575 3 PID050005ND 13,770 5362 575 3 PID060005ND 16,087 7783 575 3 PID075005ND 17,993 77
100 575 3 PID100005ND 21,833 110131 575 3 PID125005ND 26,238 110
Pentek Intellidrive™ XL Pump Controller
38 CB1525P_CAN (03/01/17)
TYPE “B” CLOSE COUPLED CENTRIFUGALS
Pentek® PPX Three Phase Pump Panels
Part NumberMax HP of Contactor Disconnect A Max Total A
OL Current range NEMA size List price
208 VACPPX-1A-13-30R 7.5 30 13.5 6.5 - 13.5 1 $1,064PPX-1A-27-30R 7.5 30 27 13 - 27 1 1,064PPX-2A-50-60R 10 60 50 25 - 50 2 1,434
PPX-3A-70-100R 25 100 70 35 - 70 3 1,943PPX-3A-135-100R 25 100 100 65 - 135 3 1,943
230-240 VACPPX-1B-13-30R 7.5 30 13.5 6.5 - 13.5 1 1,064PPX-1B-27-30R 7.5 30 27 13 - 27 1 1,064PPX-2B-50-60R 15 60 50 25 - 50 2 1,434
PPX-3B-135-100R 30 100 100 65-135 3 1,943460-480 VAC
PPX-1C-13-30R 10 30 13.5 6.5 - 13.5 1 1,064PPX-1C-27-30R 10 30 27 13 - 27 1 1,064PPX-2C-50-60R 25 60 50 25 - 50 2 1,434
PPX-3C-70-100R 50 100 70 35-70 3 1,943PPX-3C-135-100R 50 100 100 65-135 3 1,943PPX-4C-135-200R 100 200 135 65-135 4 3,573
575-600 VACPPX-1D-13-30R 10 30 13.5 6.5 - 13.5 1 1,064PPX-2D-50-60R 25 60 50 25 - 50 2 1,434
PPX-3D-135-100R 50 100 100 65-135 3 1,943
CB1525P_CAN (03/01/17)39
TYPE “B” FRAME MOUNT
Berkeley® Z Series – Hydraulic Motor Drive
9” – Nominal Impeller Diameter
Model Number
(Size) Rotation Shaft SealImpeller Material
Volute Connection
Catalog Number List Price
Weight (Lbs.)
B3ZRMCW
Packing Cast Iron
NPT B80357 $3,996
108(3 x 4 x 9 M) Victaulic B81203 4,080
Flanged B81205 3,920
CCW NPT B80360 3,996 Victaulic B81204 4,080
B4ZRKH CW Packing Cast Iron NPT B80468 6,154 195(4 x 4 x 9)NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required.
Belt and Coupling Drive
Model Number
(Size)Drive Type Rotation Shaft Seal
Impeller Material
Volute Connection
Catalog Number List Price
Weight (Lbs.)
B1MRS CouplingCCW
Mechanical
Cast Iron
NPT
B56413 $918 15(1 x 1-1/4 x 4)B1XRS Coupling B56414 918 15(1 x 1-1/4 x 5) BELT B01784 918 20B1XRMS Coupling
CW
Silicon Bronze
B56415S 810 17(1 x 1-1/4 x 5) BELT B07005S 827 B1-1/2TRLS
CouplingCast Iron B56417 1,322 37
(1-1/2 x 2 x 6 L) Silicon Bronze B74361 1,362 37
Belt
Cast Iron
B03539 1,322 35B2TRMS Coupling B56418 1,355 37(2 x 2-1/2 x 6 M) BELT B03540 1,355 40B2-1/2TRMS Coupling B56419 1,438 41(2-1/2 x 3 x 6 M) BELT B03541 1,438 42B3TRMS Coupling B56420 1,570 45(3 x 4 x 6 M) BELT B03542 1,570 50
40 CB1525P_CAN (03/01/17)
TYPE “B” FRAME MOUNT
Berkeley® Z Series
9” – Nominal Impeller Diameter
Model Number
(Size) Rotation Shaft SealImpeller Material
Volute Connection
Catalog Number List Price
Weight (Lbs.)
B1-1/2ZRL
CWPacking
Cast Iron
NPT
B52383 $2,153 90(1-1/2 x 2 x 9 L) Silicon
Bronze B74963 2,196 80
B1-1/2ZRLS Mechanical Cast Iron B68454 2,421 80(1-1/2 x 2 x 9 L)B2ZRL
CWPacking
Cast Iron NPTB55566 2,391
90(2 x 2-1/2 x 9 L)B2ZRLS Mechanical B68410 2,651(2 x 2-1/2 x 9 L)B2ZRM
CWPacking
Cast Iron NPTB52170 2,430
90(2 x 2-1/2 x 9 M)B2ZRMS Mechanical B68411 2,705(2 x 2-1/2 x 9 M)B2-1/2ZRL
CWPacking
Cast Iron
NPT
B52385 2,835 105(2-1/2 x 3 x 9 L) Silicon
Bronze B74966 2,854 100
B2-1/2ZRLS Mechanical Cast Iron B68412 3,094 100(2-1/2 x 3 x 9 L)B2-1/2ZRM
CWPacking
Cast Iron NPTB52175 2,889 75(2-1/2 x 3 x 9 M)
B2-1/2ZRMS Mechanical B68413 3,144 100(2-1/2 x 3 x 9 M)B3ZRM¨
CW
Packing Cast Iron
NPT B66161 3,081 108(3 x 4 x 9 M) Standard Frame
NPT w/hyd adapter B59539 4,133 120
Victaulic B66899 3,249 95
CCW
NPT B66168 3,081 104NPT w/hyd
adapter B59538 4,252 120
Victaulic B66895 3,249 100B3ZRMS¨
CWMechanical
Cast IronNPT B68414 3,327 120
(3 x 4 x 9 M) Standard Frame
Flanged B70280 3,327 120Victaulic B68417 3,488 130
Silicon Bronze Flanged B77324 3,318 120
CCW Cast Iron NPT B68415 3,327 104Victaulic B68416 3,488 130
B3ZRMCW
Packing Cast Iron
NPT B85579 3,548 158Heavy Duty Frame Flanged B85580 3,718 160Standard Frame Footprint
Victaulic B85581 3,718 158
CCW NPT B85578 3,548 158Victaulic B85582 3,718 158
B4ZRBH
CW
Packing
Cast Iron Flanged
B85713 4,343 300(4X5X9 BH)B4ZRBHS Mechanical B85714 4,617 300(4X5X9 BH)B5ZRBH Packing B85715 4,826 350(5X6X9 BH)B5ZRBHS Mechanical B85716 5,127 350(5X6X9 BH)
CB1525P_CAN (03/01/17)41
TYPE “B” FRAME MOUNT
Berkeley® Z Series
9” – Nominal Impeller Diameter
Model Number
(Size) Rotation Shaft SealImpeller Material
Volute Connection
Catalog Number List Price
Weight (Lbs.)
B6ZRL
CW
Packing
Cast Iron Flanged
B80431 5,065
240
(6 x 8 x 9 L) Heavy Duty FrameB6ZRLS
Mechanical B80432 5,379 (6 x 8 x 9 L) Heavy Duty FrameB6ZRL¨
CWPacking
Cast Iron FlangedB69504 4,809
190(6 x 8 x 9 L) B6ZRLS¨ Mechanical B69760 4,986 (6 x 8 x 9 L) B6ZRM¨ CCW Flange
Kit Needed. See page 53
PackingCast Iron Flanged
B66167 4,175 190(6 x 8 x 9 M)
B6ZRMS¨ Mechanical B63821 3,360 (6 x 8 x 9 M)B6ZRH
CW
Packing Cast Iron Flanged B80433 4,965
240
(6 x 8 x 9 H “HD”) Heavy Duty FrameB6ZRHS
Mechanical Cast Iron Flanged B85529 5,186 (6 x 8 x 9 H “HD”) Heavy Duty FrameB6ZRH¨
CWPacking
Cast Iron FlangedB69501 4,809 169(6 x 8 x 9 H)
B6ZRHS¨ Mechanical B69500 4,986 190(6 x 8 x 9 H)B6ZRBHH
CWPacking
Cast Iron FlangedB85717 7,606 405(6X8X9 PBHH)
B6ZRBHHS Mechanical B85718 7,952 405(6X8X9 PBHH)
42 CB1525P_CAN (03/01/17)
TYPE “B” FRAME MOUNT
Berkeley® E Series
10” – Nominal Impeller Diameter
Model Number (Size) Rotation Shaft Seal
Impeller Material
Volute Connection
Catalog Number List Price
Weight (Lbs.)
B1-1/2ERL
CWPacking Silicon
Bronze NPTB75017 $4,126
85(1-1/2 x 2 x 10 L)B1-1/2ERLS Mechanical B60194S 4,841 (1-1/2 x 2 x 10 L)B2ERL
CW PackingCast Iron
NPTB60656 4,510
95(2 x 3 x 10 L)B2ERL Silicon
Bronze B85321 5,367 (2 x 3 x 10 L)
B2ERL CCW Packing Cast Iron NPT B60657 4,510 95(2 x 3 x 10 L)B2ERLS CW Mechanical Cast Iron NPT B60892 4,935 95(2 x 3 x 10 L)B2ERH
CWPacking
Cast Iron NPTB60658 4,510
95(2 x 3 x 10 H)B2ERHS Mechanical B61368 4,935 (2 x 3 x 10 H)B2ERBH
CWPacking
Cast Iron NPTB54345 5,576
165(2 x 3 x 10 BH)B2ERBHS Mechanical B73020 5,828 (2 x 3 x 10 BH)B2ERHH CW Packing Cast Iron NPT B55829 4,510 95(2 x 3 x 10 HH)B2ERHH CCW Packing Cast Iron NPT B55159 4,510 116(2 x 3 x 10 HH)B2ERHHS CW Mechanical Cast Iron NPT B75178 4,729 116(2 x 3 x 10 HH)B3ERBL CW Packing
Cast Iron NPT
B58063 6,183 215(3 x 4 x 10 BL) CCW B58064 6,183 180B3ERBLS CW Mechanical B73019 6,389 180(3 x 4 x 10 BL) CCW B73022 6,389 180B3ERM
CWPacking
Cast Iron NPTB55210 5,241
115(3 x 4 x 10 M)B3ERMS Mechanical B61799 5,433 (3 x 4 x 10 M)B4ERM CW Packing Cast Iron Flanged B55211 5,517 155(4 x 5 x 10 M)B4ERBM CW Packing Cast Iron Flanged B58811 6,540 225(4 x 5 x 10 BM) CCW B58810 6,540 200B4ERBMS CW Mechanical Cast Iron Flanged B73023 6,814 200(4 x 5 x 10 BM) CCW B73027 7,013 200B5ERH
CWPacking
Cast Iron FlangedB66929 8,874
340(5 x 6 x 10 H)B5ERHS Mechanical B66928 7,820 (5 x 6 x 10 H)
NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required. See page 45 for ordering instructions.
CB1525P_CAN (03/01/17)43
TYPE “B” FRAME MOUNT
Berkeley® G Series
12” – Nominal Impeller Diameter
Model Number (Size) Rotation Shaft Seal
Impeller Material
Volute Connection
Catalog Number
List Price*
Weight (Lbs.)
B4GRMBH
CWPacking
Silicon Bronze Flanged
B75569 $8,849328
(4 x 6 x 12 BH)B4GRMBHS Mechanical B75570 9,336(4 x 6 x 12 BH) Dry-Run B75570D 10,553B8GRMBM CW Packing
Cast Iron Flanged
B52379 12,224 440(8 x 10 x 12 BM) CCW B52380 12,224
490B8GRMBMS CW Mechanical B66915 13,029(8 x 10 x 12 BM) CCW B66916 13,029
CW Dry-Run B66915D 14,352B10GRMBM
CW
Packing
Cast Iron Flanged
B52381 13,388 430(10 x 12 x 12 BM)B10GRMBMS Mechanical B66917 14,193 495(10 x 12 x 12 BM)
Dry-Run B66917D 15,515NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required.*Berkeley Dry-Run pumps include: Mechanical Seal, Dry-Run Gland with Lip Seal, Hardened Stainless Steel Shaft Sleeve, Lubricant Reservoir & Tubing. See page 54 for Dry-Run Spare Parts Kits.See page 40 for ordering instructions.
44 CB1525P_CAN (03/01/17)
TYPE “B” FRAME MOUNT
Berkeley® J Series
13” – Nominal Impeller Diameter
Model Number (Size) Rotation Shaft Seal
Impeller Material
Volute Connection
Catalog Number
List Price*
Weight (Lbs.)
B2-1/2JRMBM
CWPacking
Cast Iron NPTB52362 $7,383 278(2-1/2 x 4 x 13 BM)
B2-1/2JRMBMS Mechanical B66925 7,869 135(2-1/2 x 4 x 13 BM)B3JRMBM CW Packing
Cast Iron NPT
B52363 7,491 265(3 x 4 x 13 BM) CCW B52364 7,491 278B3JRMBMS CW Mechanical B66924 8,373
150(3 x 4 x 13 BM) CCW B61999 7,980CW Dry-Run B66924D 9,969
B4JRMBH CW Packing
Cast Iron Flanged
B62321 8,242 312(4 x 5 x 13 BH) CCW B62323 8,242
310B4JRMBHS CW Mechanical B61050 9,130(4 x 5 x 13 BH) CCW B66923 8,873
CW Dry-Run B61050D 10,482B4JRMBHH
CWPacking
Cast Iron FlangedB62328 7,594 320(4 x 6 x 13 BHH)
B4JRMBHHS Mechanical B61657 7,869 310(4 x 6 x 13 BHH) Dry-Run B61657D 9,454B6JRMBL CW Packing
Cast Iron Flanged
B52375 8,849 390(6 x 8 x 13 BL) CCW B52376 8,849 350B6JRMBLS CW Mechanical B66919 9,723 390(6 x 8 x 13 BL)B6JRMBM CW≠ Packing
Cast Iron Flanged
B80368 9,284
390(6 x 8 x 13 BM) CCW B56775 9,504B6JRMBMS CW≠ Mechanical B80367 10,149(6 x 8 x 13 BM) CCW B66920 10,385
CW Dry-Run B80367D 11,664B6JRMBH
CWPacking
Cast Iron FlangedB58238 10,029
360(6 x 8 x 13 BH)B6JRMBHS Mechanical B75059 11,905 (6 x 8 x 13 BH)B8JRBH
CW
Packing
Cast Iron Flanged
B85798 12,928 1100(8X10X13 PBH)B8JRBHS Mechanical B85799 13,004 1100(8X10X13 PBH)B10JRBH Packing B85796 17,271 1200(10X12X13 PBH)B10JRBHS Mechanical B85797 17,373 1200(10X12X13 PBH)
*Berkeley Dry-Run pumps include: Mechanical Seal, Dry-Run Gland with Lip Seal, Hardened Stainless Steel Shaft Sleeve, Lubricant Reservoir & Tubing. See page 54 for Dry-Run Spare Parts Kits.
CB1525P_CAN (03/01/17)45
TYPE “B” FRAME MOUNT
Berkeley® EX Series
15” – Nominal Impeller Diameter
Model Number (Size) Rotation Shaft SealImpeller Material
Volute Connection
Catalog Number List Price
Weight (Lbs.)
B6EXRBL
CW Packing Cast Iron FlangedB53962 $16,234
605(6 x 8 x 15 BL)B6EXRBH B56755 16,234 (6 x 8 x 15 BH)
NOTE: Suction and Discharge Companion Flange Kit pricing can be found on page 53, if required.¨ Model B4JRMBHH does not have a standard suction flanged connection. Requires a 6” x 10” special suction flange available through Berkeley.≠ New double volute case with splitter - Check literature for dimensional and performance information.See page 46 for ordering instructions.
Berkeley® EY Series18” – Nominal Impeller Diameter
Model Number (Size) Rotation Shaft SealImpeller Material
Volute Connection
Catalog Number List Price
Weight (Lbs.)
B4EYRMBM
CWPacking
Cast Iron FlangedB85282 12,683 465(4 x 5 x 18 BM)
B4EYRMBMS Mechanical B85284 13,180 490(4 x 5 x 18 BM) Dry-Run B85284D 15,255B4EYRMBH
CWPacking
Cast Iron FlangedB85283 12,323
490(4 x 5 x 18 BH)B4EYRMBHS Mechanical B85285 13,564(4 x 5 x 18 BH)
Self-PrimeModel Number
(Size) Drive Type Rotation Shaft SealImpeller Material
Volute Connection
Catalog Number List Price
Weight (Lbs.)
B2XRKS Coupling
CW Mechanical Cast IronSuction-FPT Discharge-
Flange
B56562 $1,480 33
(2 x 2 x 5)V-Belt B06310 1,509 45
B3TRKS Coupling B60772 3,045 60
(3 x 3 x 6)V-Belt B60771 3,244 95
B4ZRKS¨ Coupling B82375 7,112 300(4 x 4 x 9)¨ New heavy-duty Z Frame.
Ordering InstructionsThe following information is required with each order.1. Pump Model2. Catalog Number3. Required Flow Rate, Head and RPM4. Impeller Diameter (See Cutting Charge)PRICES INCLUDEFrame-mounted pump with integral shaft and ball-bearing assembly either:1. Designed for use with a flexible coupling - or -2. Fitted with a conventional pulley for belt-drive.NOTE: Baseplate, coupling, guards, shields and other required components are not included and must be purchased separately. Refer to Tech Data 4163 for details of various drive arrangements.CONNECTION OPENINGS – Suction and discharge openings are NPT tapped for standard pipe as indicated.ROTATION – Clockwise (CW) or counter-clockwise (CCW) when looking at pulley end of shaft.
46 CB1525P_CAN (03/01/17)
TYPE “B” SAE MOUNT — FOR FLYWHEEL HOUSINGS
Berkeley® Z Series
9” – Nominal Impeller Diameter
Model Number (Size)
Shaft Seal
Impeller Material
Volute Connection
Shaft Spline
SizeShaft Ext.
SAE HSG Size
Basic Pump End Unmounted Less Flywheel Coupling
Weight (Lbs.)
Catalog Number List Price
B1-1/2ZQM
Packing Cast Iron NPT 1-3/8”-10T 2-1/2”
5 B70315 $4,326 115(1-1/2 x 2 x 9 M)B2ZQM 5 B65985 4,407 120(2 x 2-1/2 x 9 M)B2-1/2ZQM 5 B65989 4,881 130(2-1/2 x 3 x 9 M) 3” 4 B71826 4,881 130
9” - Nominal Impeller Diameter
Model Number
(Size) Shaft SealImpeller Material
Volute Connection
Shaft Spline
Size Shaft Ext.
Coupling Catalog Number
(Included)Clutch
Size
Pump Catalog
Number¨
List Price (Including
Elastomeric Coupling)
Weight (Lbs.)
B3ZQM¨
Packing Cast Iron
Flanged
1-1/2”-10T SAE 4–2-3/4” SAE 5–2-1/2”
B85398 6.5” B80831 $6,051
250(3 x 4 x 9 M) B85400 7.5” B80830 6,051 Heavy Duty Frame
B85402 8” B80833 6,051 B85404 10” B80832 6,133
Victaulic
B85398 6.5” B80835 6,215
225
B85400 7.5” B80834 6,215 B85402 8” B80837 6,215 B85404 10” B80836 6,301
NPT
B85398 6.5” B80839 6,051 B85400 7.5” B80838 6,051 B85402 8” B80841 6,051 B85404 10” B80840 6,133
B3ZQMS¨
Mechanical Cast Iron
Flanged
1-1/2”-10T SAE 4–2-3/4” SAE 5–2-1/2”
B85398 6.5” B80843 6,384
250(3 x 4 x 9 M) B85400 7.5” B80842 6,384 Heavy Duty Frame
B85402 8” B80845 6,384 B85404 10” B80844 6,468
Victaulic
B85398 6.5” B80847 6,553
225
B85400 7.5” B80846 6,553 B85402 8” B80998 6,553 B85404 10” B80848 6,634
NPT
B85398 6.5” B80851 6,384 B85400 7.5” B80850 6,384 B85402 8” B80853 6,384 B85404 10” B80852 6,468
B6ZQL¨
Packing Cast Iron NPT 1-1/2”-10T SAE 4–2-3/4” SAE 5–2-1/2”
B85398 6.5” B80855 7,282
325(6 x 8 x 9 L) B85400 7.5” B80854 7,282 Heavy Duty Frame
B85402 8” B80857 7,282 B85404 10” B80856 7,366
B6ZQLS¨
Mechanical Cast Iron Flanged 1-1/2”-10T SAE 4–2-3/4” SAE 5–2-1/2”
B85398 6.5” B80859 7,615
325(6 x 8 x 9 L) B85400 7.5” B80858 7,615 Heavy Duty Frame
B85402 8” B80861 7,615 B85404 10” B80860 7,700
¨Pump includes a heavy duty elastomeric coupling.*“Z” series SAE pumps are dual machined to fit SAE #4 and SAE#5 engine bell housings. List prices include elastomeric coupling. Please refer to chart above for appropriate clutch size.
CB1525P_CAN (03/01/17)47
TYPE “B” SAE MOUNT — FOR FLYWHEEL HOUSINGS
Berkeley® E Series10” – Nominal Impeller Diameter
Model Number (Size)
Shaft Seal
Impeller Material
Volute Connection
Shaft Spline
Size Shaft Ext.
SAE HSG Size
Basic Pump End Unmounted Less
Flywheel CouplingWeight (Lbs.)
Catalog Number List Price
B1-1/2EQL
Packing Cast Iron
NPT
2-1/2” 5 B71848 $5,822 170(1-1/2 x 2 x 10 L)B2EQHH 2-1/2” 5 B71850 6,060 160(2 x 3 x 10 HH) 3” 4 B71849 6,060 160B3EQBL 2-1/2” 5 B71978 6,470 180(3 x 4 x 10 BL) 3” 4 B71979 6,470 180B4EQM
Flanged2-1/2” 5 B71855 7,646 200
(4 x 5 x 10 M) 4 B71981 7,327 200B5EQBH 3” 4 B71860 8,537 350(5 x 6 x 10 BH)
9” - Nominal Impeller Diameter
Model Number
(Size) Shaft SealImpeller Material
Volute Connection
Shaft Spline
Size Shaft Ext.
Coupling Catalog Number
(Included)Clutch
Size
Pump Catalog
Number¨
List Price (Including
Elastomeric Coupling)
Weight (Lbs.)
B6ZQH¨
Packing Cast Iron Flanged 1-1/2”-10T SAE 4–2-3/4” SAE 5–2-1/2”
B85398 6.5” B80863 7,282
325(6 x 8 x 9 H) B85400 7.5” B80862 7,282 Heavy Duty Frame
B85402 8” B80865 7,282 B85404 10” B80864 7,366
B6ZQHS¨
Mechanical Cast Iron Flanged 1-1/2”-10T SAE 4–2-3/4” SAE 5–2-1/2”
B85398 6.5” B80867 7,615
325(6 x 8 x 9 H) B85400 7.5” B80866 7,615 Heavy Duty Frame
B85402 8” B80869 7,615 B85404 10” B80868 7,700
¨Pump includes a heavy duty elastomeric coupling.*“Z” series SAE pumps are dual machined to fit SAE #4 and SAE#5 engine bell housings. List prices include elastomeric coupling. Please refer to chart above for appropriate clutch size.
Berkeley® Z Series
Model Number
(Size) Shaft SealImpeller Material
Volute Connection
Shaft Spline Size
Shaft Ext.
SAE HSG Size
Catalog Number
List Price
Weight (Lbs.)
B4ZQBH Packing
Cast Iron Flanged
1-1/2”–10T (3) 2.81 (4) 2.63
3/4
B85719 $6,395 300(4X5X9 BH)B4ZQBHS Mechanical B85720 6,689 300(4X5X9 BH)B5ZQBH Packing B85721 6,876 350(5X6X9 BH)B5ZQBHS Mechanical B85722 7,190 350(5X6X9 BH)B6ZQBHH Packing
1.5”–10T 3”B85723 7,522 405(6X8X9 PBHH)
B6ZQBHHS Mechanical B85724 7,864 405(6X8X9 PBHH)
48 CB1525P_CAN (03/01/17)
TYPE “B” SAE MOUNT — FOR FLYWHEEL HOUSINGS
Berkeley® G Series
12” – Nominal Impeller Diameter
Model Number (Size) Shaft Seal
Impeller Material
Volute Connection
Shaft Spline
SizeShaft Ext.
SAE HSG Size
Basic Pump End Unmounted Less
Flywheel CouplingWeight (Lbs.)
Catalog Number List Price
B4GQBH
Packing Silicon Bronze Flanged 1-1/2”-10T 3”
4 B75561 9,978 328(4 x 6 x 12 BH) 3 B75562 9,978 353
2 B75563 10,477 4181 B75564 10,474 418
B4GQBHS
Mechanical
Silicon Bronze Flanged 1-1/2”-10T 3”
4 B75565 10,468 328(4 x 6 x 12 BH) 3 B75566 10,468 353
2 B75567 10,989 4181 B75568 10,989 418
Dry-Run
4 B75565D 12,148 3283 B75566D 12,148 3532 B75567D 12,148 4181 B75568D 12,148 418
B8GQBM
Packing Cast Iron Flanged 1-1/2”-10T 3”
4 B78723 9,867 445(8 x 10 x 12 BM) 3 B66103 10,296 455
2 B66104 10,296 4601 B68910 10,296 475
B8GQBMS
Dry-Run Cast Iron Flanged 1-1/2”-10T 3”
4 B78723D 11,135 445(8 x 10 x 12 BM) 3 B66103D 11,619 455
2 B66104D 11,619 4601 B68910D 11,619 475
B10GQBMPacking Cast Iron Flanged 1-1/2”-10T 3”
3 B66106 12,369 800(10 x 12 x 12 BM) 2 B68935 12,369 800
1 B66107 12,369 800B10GQBMS
Dry-Run Cast Iron Flanged 1-1/2”-10T 3”3 B66106D 13,688 800
(10 x 12 x 12 BM) 2 B68935D 13,688 8001 B66107D 13,688 800
*Berkeley Dry-Run pumps include: Mechanical Seal, Dry-Run Gland with Lip Seal, Hardened Stainless Steel Shaft Sleeve, Lubricant Reservoir & Tubing.
CB1525P_CAN (03/01/17)49
TYPE “B” SAE MOUNT — FOR FLYWHEEL HOUSINGS
Berkeley® J Series
13” – Nominal Impeller Diameter
Model Number (Size) Shaft Seal
Impeller Material
Volute Connection
Shaft Spline
SizeShaft Ext.
SAE HSG Size
Basic Pump End Unmounted Less
Flywheel CouplingWeight (Lbs.)
Catalog Number List Price*
B2-1/2JQBLPacking Cast Iron NPT 1-3/8”-10T 3” 3 B65992 $7,493 345
(2-1/2 x 4 x 13 BL) 4 B68548 7,493 3452-1/2” 5 B68598 7,493 345
B2-1/2JQBLS Mechanical Cast Iron NPT 1-3/8”-10T 3” 4 B75451 8,110 345(2-1/2 x 4 x 13 BL) 2-1/2” 5 B75234 8,110 345B2-1/2JQBM
Packing Cast Iron NPT 1-3/8”-10T 3” 3 B65995 7,493 293
(2-1/2 x 4 x 13 BM) 4 B68551 7,493 3452-1/2” 5 B65998 7,493 345
3” 2 B69337 7,493 345B2-1/2JQBMS Mechanical Cast Iron NPT 1-3/8”-10T 3”
3 B75300 8,110 345(2-1/2 x 4 x 13 BM) 4 B78033 8,110 345
Dry Run 1-1/2”-10T 4 B78033D 9,410 425B3JQBM
Packing Cast Iron NPT 1-1/2”-10T
2-1/2” 5 B80708 7,770 365(3 x 4 x 13 BM)
3”
4 B80707 7,770 2943 B80706 7,770 3002 B80705 7,770 3651 B80704 7,770 365
B3JQBMS MechanicalCast Iron NPT 1-1/2”-10T 3”
4 B80709 8,701 365(3 x 4 x 13 BM) 3 B80710 8,701 365
Dry-Run 4 B80709D 10,002 3653 B80710D 10,002 365
B4JQBH
Packing Cast Iron Flanged
1-3/8”-10T
3”
5 B73400 8,252 400(4 x 5 x 13 BH) 4 B66024 8,610 324
3 B66027 8,610 4002 B66025 8,610 330
1-1/2”-10T
4 B66030 8,610 3203 B66026 8,610 3352 B66031 8,610 4001 B68906 8,610 400
B4JQBH
Packing Silicon Bronze Flanged
1-3/8”-10T
3”
5 B75000 8,995 400(4 x 5 x 13 BH) 4 B75001 8,995 400
3 B75002 8,995 4002 B75003 8,995 400
1-1/2”-10T
4 B75004 8,995 4003 B75005 8,995 4002 B75006 8,995 4001 B75007 8,995 400
B4JQBHS
MechanicalCast Iron
Flanged 1-1/2”-10T 3”
3 B67294 9,584 320(4 x 5 x 13 BH) 2 B71834 9,584 400
Silicon Bronze
3 B75010 9,926 4002 B75011 9,926 400
Dry-Run Cast Iron 3 B67294D 10,938 3202 B71834D 10,938 320
B6JQBL Packing Cast Iron Flanged 1-3/8”-10T 3” 4 B68564 9,982 355(6 x 8 x 13 BL) 3 B66065 9,982 475
*Berkeley DRY-RUN pumps include: Mechanical Seal, DRY-RUN Gland with Lip Seal, Hardened Stainless Steel Shaft Sleeve, Lubricant Reservoir & Tubing. See page 54 for DRY-RUN Spare Parts Kits.
50 CB1525P_CAN (03/01/17)
TYPE “B” SAE MOUNT — FOR FLYWHEEL HOUSINGS
Berkeley® EX Series
15” – Nominal Impeller Diameter
Model Number
(Size) Shaft SealImpeller Material
Volute Connection
Shaft Spline
Size Shaft Ext.SAE HSG
Size
Basic Pump End Unmounted Less
Flywheel CouplingWeight (Lbs.)
Catalog Number List Price
B4EXQBLSMechanical Cast Iron Flanged 1-1/2”-10T 3”
3 B66034 $15,854 545(4 x 6 x 15 BL) 2 B68501 15,854 545
1 B68500 14,960 545B5EXQBHS
Mechanical Cast Iron Flanged 1-1/2”-10T 3”3 B66055 16,251 630
(5 x 6 x 15 BH) 2 B66054 16,251 4451 B66056 16,251 630
B6EXQBM
Packing Cast Iron Flanged 1-1/2”-10T 3”
4 B70385 11,548 490(6 x 8 x 13.5 BM) 3 B70384 11,784 399
2 B70383 11,784 4901 B70382 11,784 490
Berkeley® J Series
13” – Nominal Impeller Diameter
Model Number (Size) Shaft Seal
Impeller Material
Volute Connection
Shaft Spline
SizeShaft Ext.
SAE HSG Size
Basic Pump End Unmounted Less
Flywheel CouplingWeight (Lbs.)
Catalog Number List Price
B6JQBM
Packing
Cast Iron
Flanged 1-1/2”-10T 3”
4 B80375 9,750 475(6 x 8 x 13 BM) 3 B80376 9,750 370
2 B80377 9,750 4751 B80378 9,750 372
Silicon Bronze
1 B80380 10,759 4752 B80381 10,759 4753 B80382 10,759 4754 B80383 10,759 475
B6JQBMSMechanical Silicon
Bronze Flanged 1-1/2”-10T 3” 3 B80385 10,700 475(6 x 8 x 13 BM)
B8JQBH Packing
Cast Iron Flanged 2”–10T 3” 2/3
B85802 13,704 1100(8X10X13 PBH)B8JQBHS Mechanical B85803 14,510 1100(8X10X13 PBH)B10JQBH Packing B85800 19,764 1200(10X12X13 PBH)B10JQBHS Mechanical B85801 19,878 1200
CB1525P_CAN (03/01/17)51
TYPE “B” SAE MOUNT — FOR FLYWHEEL HOUSINGS
Berkeley® XT Series
15.5” – Nominal Impeller Diameter
Model Number (Size) Shaft Seal
Impeller Material
Volute Connection
Shaft Spline
SizeShaft Ext.
SAE HSG Size
Basic Pump End Unmounted Less
Flywheel CouplingWeight (Lbs.)
Catalog Number
List Price*
B6XTQBHPacking Cast Iron Flanged 1-1/2”-10T
3” 2/3 B85333 16,432 564(6 x 8 x 15.5 BH) 2 1 B85335 16,432 59415.5” TrimB6XTQBHS
Dry-Run Cast Iron Flanged 1-1/2”-10T 3”2/3 B85333D 18,122
564(6 x 8 x 15.5 BH) 1 B85335D 18,12215.5” TrimB6XTQBH
Packing Cast Iron Flanged 1-1/2”-10T 3” 2/3 B85334 16,432 560
(6 x 8 x 15.5 BH) 2 1 B85336 16,432 59014” TrimB6XTQBHS-14”
Dry-Run Cast Iron Flanged 1-1/2”-10T 3”2/3 B85334D 18,122
560(6 x 8 x 15.5 BH) 1 B85336D 18,12214” Trim
Berkeley® EY Series 18” – Nominal Impeller Diameter
Model Number (Size) Shaft Seal
Impeller Material
Volute Connection
Shaft Spline
SizeShaft Ext.
SAE HSG Size
Basic Pump End Unmounted Less
Flywheel CouplingWeight (Lbs.)
Catalog Number
List Price*
B4EYQBM
Packing Cast Iron Flanged 1-1/2”-10T 3”
4 B85288 12,780
620(4 x 5 x 18 BM) 3 B85287 12,780
2 B85292 12,780 1 B85293 12,780
B4EYQBHPacking Cast Iron Flanged 1-1/2”-10T 3”
3 B85290 12,780 620(4 x 5 x 18 BH) 2 B85289 12,780
1 B85291 12,780 B4EYQBHS Mechanical Cast Iron Flanged 1-1/2”-10T 3” 3 B85286 13,047 620(4 x 5 x 18 BH)B4EYQBHS Mechanical
Cast Iron Flanged 1-1/2”-10T 3”2 B85342 13,047
620(4 x 5 x 18 BH)Dry-Run 3 B85286D 14,739
2 B85342D 14,739 NOTE: Suction and discharge companion flange kit pricing can be found on page 53.See page 6 for model description.*Berkeley Dry-Run pumps include: Mechanical Seal, Dry-Run Gland with Lip Seal, Hardened Stainless Steel Shaft Sleeve, Lubricant Reservoir & Tubing. See page 54 for Dry-Run Spare Parts Kits.
52 CB1525P_CAN (03/01/17)
TYPE “B” SAE MOUNT — FOR FLYWHEEL HOUSINGS
Model Number
(Size) Shaft SealImpeller Material
Volute Connection
Shaft Spline
Size Shaft Ext.SAE HSG
Size
Basic Pump End Unmounted Less
Flywheel CouplingWeight (Lbs.)
Catalog Number
List Price*
B4ZQKLS
Mechancial Cast Iron NPT 1-3/8”-10T
2-1/2” 5 B69490 $8,181 320(4 x 4 x 9 L) 3” 4 B69350 8,181 320B4ZQKHS 2-1/2” 5 B66110 8,181 320(4 x 4 x 9 H) 3” 4 B68865 8,181 215
NOTE: Basic pump end includes centrifugal pump end (unmounted), with ball bearing bracket assembly for mounting on engine with standard SAE flywheel housing. Flywheel coupling is not included.
Berkeley® Z Frame Series – New Self Priming Heavy Duty
Model Number
(Size) Shaft SealImpeller Material
Volute Connection
Shaft Spline
SizeShaft Ext.
Coupling Catalog Number
(Included)Clutch
Size
Pump Catalog
Number¨
List Price (Including
Elastomeric Coupling)
Weight (Lbs.)
B4ZQKLS
Mechanical Cast Iron NPT 1-1/2”-10T
SAE 4 - 2-3/4” SAE 5 - 2-1/2”
B85398 6.5” B82381 $9,112
325
(4 x 4 x 9 L) B85400 7.5” B82380 9,112 B85402 8” B82383 9,112 B85407 10” B82382 9,153
B4ZQKHS B85398 6.5” B82377 9,112 (4 x 4 x 9 H) B85400 7.5” B82376 9,112
B85402 8” B82379 9,112 B85407 10” B82378 9,112
“Z” series SAE pumps are dual machined to fit SAE #4 and SAE#5 engine bell housings. List prices include elastomeric coupling. Please refer to chart above for appropriate clutch size. Pump includes a heavy duty elastomeric coupling.
Flywheel Couplings for SAE HousingsWide RPM Range, Elastomer Mounted Hub
Clutch Size Outside Dimension Catalog Number Shaft Size R Rating List Price6.5” 8.5”OD B85397 1-3/8”-10T 7 $801 6.5” 8.5”OD B85398 1-1/2”-10T 7 801 7.5” 9.5”OD B85399 1-3/8”-10T 7 801 7.5” 9.5”OD B85400 1-1/2”-10T 7 801 8.0” 10-3/8”OD B85401 1-3/8”-10T 7 801 8.0” 10-3/8”OD B85402 1-1/2”-10T 7 801
10.0” 12-3/8”OD B85403 1-3/8”-10T 7 825 10.0” 12-3/8”OD B85407 1-3/8”-10T HD 9 1,027 10.0” 12-3/8”OD B85404 1-1/2”-10T 7 825 10.0” 12-3/8”OD B85408 1-1/2”-10T 9 1,027 11.5” 13-7/8”OD B85406 1-1/2”-10T 7 825 11.5” 13-7/8”OD B85409 1-3/8”-10T HD 9 1,027 11.5” 13-7/8”OD B85405 1-3/8”-10T 7 825 11.5” 13-7/8”OD B85410 1-1/2”-10T HD 9 1,027 11.5” 13-7/8”OD M15654 2”-10T 16 3,062 11.5” 13-7/8”OD M15655 2”-10T 19 3,062 14” 18-3/8”OD B85411 1-1/2”-10T HD 9 1,027
NOTE: All splines are 10T. A flywheel coupling is required for the connection of pumps to engines with SAE flywheel housings. The standard flywheel couplings listed here are shown on dimension sheet 4117. Suction and Discharge companion flange kit pricing can be found on page 53.To determine “R” Rating, divide horsepower by RPM and multiply by 100.EXAMPLE: (120 ÷ 1800) x 100 = 6.66 – A coupling with an “R” Rating of 7 would be used.
CB1525P_CAN (03/01/17)53
TYPE “B” AIR-COOLED (GAS) PUMPS
Engine Drive
Model Number HPEngine
ManufacturerEngine Model
Engine Type
Engine Starter
Fuel Tank Capacity
(Gal.)Mounting
TypeCatalog Number
List Price
Weight Lbs.
End SuctionB1WQS-9 9 Robin® EX27 OHC Rewind 1.59 Base Mtd. B72133 $3,222 182B1-1/2TQMS-9 9 Robin EX27 OHC Rewind 1.59 Base Mtd. B72136 3,531 152B1-1/2TQMS-12 12 Robin EX35 OHV Electric 1.59 Base Mtd. B72599 4,267 226B1-1/2TQMS-14 14 Robin EX40 OHV Electric 1.85 Base Mtd. B71146 6,149 187B1-1/2ZQLS-14 14 Robin EX40 OHV Electric 1.85 Base Mtd. B71124 7,211 221B1-1/2ZQLS-18 18 Briggs & Stratton® V-Twin OHV Electric N/A Base Mtd. B70287 7,640 265B2TQMS-14 14 Robin EX40 OHV Electric 1.85 Base Mtd. B70371 6,272 242B2ZQLS-18 18 Briggs & Stratton V-Twin OHV Electric N/A Base Mtd. B70368 8,252 275B2-1/2TQMS-14 14 Robin EX40 OHV Electric 1.85 Base Mtd. B71685 6,554 262B3TQMS-14 14 Robin EX40 OHV Electric 1.85 Base Mtd. B71123 7,245 272B3TQMS-18 18 Briggs & Stratton V-Twin OHV Electric N/A Base Mtd. B71149 7,086 285Self-PrimingB2XQKLS-4.5 4.5 Robin EX13 OHC Rewind 0.7 Roll Cage B71907 3,863 91B2XQKHS-6 6 Robin EX17 OHC Rewind 0.95 Roll Cage B71908 4,121 98B3TQKLS-9 9 Robin EX27 OHC Rewind 1.59 Base Mtd. B72139 5,865 164B3TQKLS-12 12 Robin EX35 OHV Electric 1.59 Base Mtd. B72602 7,760 282B3TQKHS-14 14 Robin EX40 OHV Electric 1.85 Base Mtd. B71543 8,859 300B4TQKLS-18 18 Briggs & Stratton V-Twin OHV Electric N/A Base Mtd. B71546 9,910 330
NOTE: On base mounted 14 HP and 18 HP units, pumps are positioned to accommodate a lawn and garden battery.Lawn & garden battery is NOT included.Battery & battery cable not included on electric start units.Fuel tank not included on 18 HP units.Optional seals available, consult factory for lead times.
Pumper and Pumper Plus Series
Model Number HPEngine
ManufacturerEngine Model
Engine Type
Engine Starter
Fuel Tank Capacity
(Gal.)Mounting
TypeCatalog Number List Price Weight Lbs.
EDP55RV 5.5 Power Pro® 5.5 OHV Rewind 0.95 Roll Cage EDP55RV 1,011 46P60R 6 Robin EX17 OHC Rewind 0.95 BaseMtd. B82932 2,031 49P60R 6 Robin EX17 OHC Rewind 0.95 Roll Cage B82933 2,734 79P90R 9 Robin EX27 OHV Rewind 1.59 BaseMtd. B82934 2,855 71P90R 9 Robin EX27 OHV Rewind 1.59 Roll Cage B82935 3,923 71
PP60R 6 Robin EX17 OHC Rewind 0.95 BaseMtd. B82936 2,305 53PP60R 6 Robin EX17 OHC Rewind 0.95 Roll Cage B82937 3,010 53PP90R 9 Robin EX27 OHV Rewind 1.59 BaseMtd. B83148 3,352 73PP90R 9 Robin EX27 OHV Rewind 1.59 Roll Cage B83149 4,466 73
54 CB1525P_CAN (03/01/17)
WASTEWATER/TRASH PUMPS
Berkeley® AG Series Vortex Pumps
Model Number
Motor Horsepower (1 PH, 230V) Voltage (1 PH only) Catalog Number List Price
Weight (Lbs)
B-AG3 3 230 B27670F002 $8,708 200B-AG5 5 230 B27670F003 $9,216 210
Controls
Model Number HP Volts Phase Type Nema
Catalog Number List Price
Weight (Lbs)
BCNC3S 3 230 1 Simplex 4X B25084C000 $2,571 21BCNC3D 3 230 1 Duplex 4X B25092C000 5,315 35BCNC5S 5 230 1 Simplex 4X B25191C000 3,610 21BCNC5D 5 230 1 Duplex 4X B25192C000 5,675 35
Float Switch
Model Number Description List Price
Weight (Lbs)
SMF25NO Mercury-free switch sealed in polypropylene, float ball weight attached to 25’ 18/2 SJQW/A cord, rated 125VA @ 115VAC, ball colored green $95 3
CB1525P_CAN (03/01/17)55
ACCESSORIES
Flange Kits and Cutting Charges
Companion Flange KitsNPT tapped suction and discharge openings are for standard pipe. All models with a discharge size 3” or smaller are NPT except for the victaulic coupled B3ZRM.Flanged suction and discharge openings are faced and drilled (per ANSI B16.1, class 125) for standard flanges. Maximum working pressure for class 30 cast iron, per ANSI B16.1, is 175 PSI unless otherwise stated on pump curve. All models with a discharge size of 4” or larger are flanged except the B6Z models as noted, and model B4JRMBHH as noted.
Series Suction Size List Price Discharge Size List PriceB2TPM
B60128 2-1/2” X 7” $149 B60120 2” X 6” $136 B2ZPLB2ZPHSB2EPBL B60129 3” X 7-1/2” 189 B60120 2” X 6” 136B2EPBHH
B2-1/2TPMB60129 3” X 7-1/2” 189 B60128 2-1/2” X 7” 149B2-1/2ZPL
B2-1/2ZPMB3TPM
B74303 4” X 9” 204 B60129 3” X 7-1/2” 189
B3TPHB3ZPLB3ZPM
B3ZPBHB3EPBLB4EPM
B59875 5” X 10” 270 B59870 4” X 9” 213B4EPBMB4JPBH
B4GPBH w/o Eccentric Reducer
B59871 5” X 10” 270 B59870 4” X 9” 213B4EYPBMB4EXPBLB4EYPBH
B4GPBH with Eccentric Reducer B59872 6” X 11” 278 B59870 4” X 9” 213B4JPBHH B59876 6” X 10” 426 B59870 4” X 9” 213
B5EPH
B59877 6” X 11” 278 B59871 5” X 10” 270B5EPBMB5WP
B5EXPBHB6ZPL
B59878 8” X 13-1/2” 404 B59872 6” X 11” 278
B6ZPHB6JPBLB6JPBMB6JPBH
B6EXPBLB6EXPBHB8GPBM B59879 10” X 16” 708 B59873 8” X 13-1/2” 404
Impeller Cutting ChargesAn impeller cutting charge will be applied for non-standard trims.
Description Catalog No. List PriceImpellers 9” diameter and smaller S16104 $233 Impellers over 9” diameter S16105 280
ACCESSORIES
Part No. Description List PriceSuction Primers
S20018 Manifold Primer $684 M12186 Replacement Diaphram Kit for #7 Protek Primer 206 M14832 TS6 Tuf-Skin Hand Primer, 6” 548 M14833 TS9 Tuf-Skin Hand Primer, 9” 812 M14834 TS6-3 Replacement Handle Tuf-Skin Hand Primer 198 M14835 TS6-5 Replacement Diaphragm Tuf-Skin Hand Primer 220 M14836 TS9-9 Replacement Handle Tuf-Skin Hand Primer 218 M14837 TS9-5 Replacement Diaphragm Tuf-Skin Hand Primer 257
Discharge Priming ValvesB02352 2 x 2-1/2 1,049 B05922 2-1/2 x 3 893 B05923 3 x 4 782 B05924 4 x 4 1,064 B05925 5 x 5 1,246 B05926 6 x 6 1,269
Packing PullerS15510 Packing Puller 70
Dry-Run Spare Part Kits
Catalog No. Pump Models Description List Price
B85599 B_G, B_J, B_EY Dry-Run Gland, with Lip Seal, Hardened SS shaft sleeve, O-ring, mechanical seal $1,775
B85600 B6XT Dry-Run Gland, with Lip Seal, Hardened SS shaft sleeve, O-ring, mechanical seal 2,309
B85576 B_G, B_J, B_EY Lubricant reservoir, tubing, mounting plate, fittings 1,774
B85577 B6XT Lubricant reservoir, tubing, mounting plate, fittings 1,774
© 2017 Pentair plc. All Rights Reserved. CB1525P_CAN (03/01/17)
Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.
PENTAIR CANADA, INC. - FLOW AND FILTRATION SOLUTIONS490 PINEBUSH ROAD, UNIT #4, CAMBRIDGE, ON N1T 0A5
CUSTOMER SERVICE: 1.888.363.PUMP (7867) | TOLL FREE FAX: 1.888.606.5484
All Pentair trademarks and logos are owned by Pentair, Inc. or its affiliates. All other registered and unregistered trademarks and logos are the property of their respective owners. Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice. Pentair is an equal opportunity employer.
Recommended