View
224
Download
0
Category
Preview:
Citation preview
7/28/2019 AUTOP 2013
1/62
7/28/2019 AUTOP 2013
2/62
All from a to .z
Inground is always possible!
Since more than 25 years autop is the specialist for the installation of inground lifts in existing
workshops. Thus we show that this is possible without any problem. With our long experience we found
solutions for nearly all conditions of the ground. The autop service team offers the civil works, assembly
and service.
Start Situation Professional desassembling Define position of the new workstation
Defining of the lifts position Cutting of the concrete
7/28/2019 AUTOP 2013
3/62
Digging with our own machines
7/28/2019 AUTOP 2013
4/62
Final assembly
7/28/2019 AUTOP 2013
5/62
Toujoursbien plac!
La plateorme est trs solide et acile daccs par sa hauteur rduite. Les
plateaux ajustables en longueur permettent le levage dune large gamme de
voitures.
La plateorme Pv est galvanise en srie et ore ainsi une sthtique de longue
dure.
Pratiques accessoires comme les cles dappui permettent un levage
proessionnel en toute scurit.
autop Sololift 1.35 Pv120-180, 140-200, 160-220
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
6/62
...une entreprise du groupe STENHJ!
Et en plus.........Nos technico-commerciaux se mettent votre disposition pour toutes demandes deplanifcation et modernisations.Veuillez nous contacter !
Donnes techniques:
Capacit de levage: 3.500 kg
Course du vrin: 1.800 mm
Hauteur de levage: 1.930 mm
Dure de monte/descente: env. 30 sec.
Diamtre du cylindre: 123 mm
Proondeur de la ondation: 2.400 mm
Branchement: 400 V / 50 Hz/16 A
Groupe moto-pompe: 3,0 kW
Sololift 1.35 Pv
Couleur standard:
galvanis et paint RAL 9006
Vrin invers en acier alli avec
surace chrome dureBride de guidage en aluminium coul
sous pression pour viter la corrosion
Commande lectronique
Descente durgence pneumatique
Dispositi anti-rotation intgr
Installation dans une cassette tanche
Livraison avec de lhuile cologique
Option:
les ttes en xy augmentent le conort
et la plage de levage
Composants:
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Sousrservedemodifcationstechniques-position12/09
7/28/2019 AUTOP 2013
7/62
Toujoursbien plac !
Le mono-vrin autop Sololit Sa a ait ses preuves dans le domaine de la carros-
serie et de la maintenance.
La capacit de levage de 3500 kg et les bras tlescopiques permettent un levage
proessionnel dune grande gamme de voitures.
Le verrouillage automatique des bras est un systme erm et ainsi labritdendommagement.
autop Sololift 1.35 Sa
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
8/62
...une entreprise du groupe STENHJ!
Service:Nos technico-commerciaux vous assistentpour la planifcation et ralisation pour les con-structions neuves et des modernisations.Contactez-nous!
Sololift 1.35 Sa
Composants:
Donnes techniques:
Capacit de levage: 3.500 kg
Course des vrins: 1.800 mm
Hauteur utilisable: 1.895-2.220 mm
Avec patins standard: 1.935-1.995 mm
Diamtre du vrin: 123 mm
Monte/Descente: env. 30 sec.
Groupe moto-pompe: 3,0 kW
Proondeur ondation: 2.400 mm
Branchement: 230/400 V/ 50 Hz/ 16A
Cylindre invers chrom-dur
Guide du vrin en aluminium coul
sous pression
Contrle lectronique
Descente durgence pneumatique
Installation dans une cassette tanche
Huile cologique en standard
Pr-montage dans la cassette avec
dispositi anti-rotation
Option:
Grand choix de patins dappui
Couleur standard:
RAL 7016 ( gris anthracite )
ou au choix
RAL 5019 ( bleu )
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
dition12/2011-Sousreservedemodifcations!
7/28/2019 AUTOP 2013
9/62
Toujoursbien plac !
Le mono-vrin autop Sololit Sa a ait ses preuves dans le domaine de la carros-
serie et de la maintenance.
La capacit de levage de 3500 kg et les bras tlescopiques permettent un levage
proessionnel dune grande gamme de voitures.
Le verrouillage automatique des bras est un systme erm et ainsi labritdendommagement.
autop Sololift 1.35 Saa
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
10/62
...une entreprise du groupe STENHJ!
Service:Nos technico-commerciaux vous assistentpour la planifcation et ralisation pour les con-structions neuves et des modernisations.Contactez-nous!
Sololift 1.35 Saa
Composants:
Donnes techniques:
Capacit de levage: 3.500 kg
Course des vrins: 1.800 mm
Hauteur utilisable: 1.895-2.220 mm
Avec patins standard: 1.935-1.995 mm
Diamtre du vrin: 123 mm
Monte/Descente: env. 30 sec.
Groupe moto-pompe: 3,0 kW
Proondeur ondation: 2.400 mm
Branchement: 230/400 V/ 50 Hz/ 16A
Cylindre invers chrom-dur
Guide du vrin en aluminium coul
sous pression
Contrle lectronique
Descente durgence pneumatique
Installation dans une cassette tanche
Huile cologique en standard
Pr-montage dans la cassette avec
dispositi anti-rotation
Option:
Grand choix de patins dappui
Couleur standard:
RAL 7016 ( gris anthracite )
ou au choix
RAL 5019 ( bleu )
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
dition12/2011-Sousreservedemodifcations!
7/28/2019 AUTOP 2013
11/62
Always onthe top!
The autop Sololit 1.30 Fv Uni is especially suitable or washing, general mainte-
nance and reconditioning o used cars.
Easy access and liting. The Sololit Fv Uni is a very exible lit; the liting area can
e.g. be modied to suit vehicles with long wheel bases, by either re-positioningthe adaptors, or alternatively tting more adaptors.
With a minimum height o only 80 mm the Sololit Fv Uni is suitable or also very
low vehicles.
The lit is hot galvanized so as to ensure long lie and reliable operation.
autop Sololift 1.30 Fv Uni
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
12/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weofer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Technical data:
Capacity: 3,000 kg
Cylinders diameter: 123 mm
Liting/lowering time: appr. 30 sec.
Stroke length: 1,800 mm
Liting height: 1,820 mm
Foundation depth: 2,400 mm
Voltage: 230/400 V
50 Hz
16 A
Power unit: 3.0 kW
Superstructure
Length, short version: 4,240 mm
Length, long version: 4,750 mm
Width: 1,050/2,090 mm
Height: 20/80 mm
Wheel base
short version: 1,800-3,400 mm
long version: 1,800-3,900 mm
Sololift 1.30Fv Uni
Standard:
hot-galvanized
hard-chromed cylinder
corrosion-ree guiding elementSPS - control unit
pneumatic emergency drain
installation in waterproo cassette
use o bio-oil non hazardous to
water
on-oor superstructure with hot gal-
vanized sturdy welded rails
Components
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecicationsthataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodiferencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthediferencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable.
7/28/2019 AUTOP 2013
13/62
Qualit auprix raisonable!
Le pont Eurolit 2.30 Pv rparation est un pont hydraulique simple et robuste,
appropri pour un levage dune large gamme de vhicules. Il ore galement
scurit et ergonomie.
La plateorme Pv ore un levage simple et rapide par un ajustement des pla-teaux en longueur.
Pratiques accessoires comme les cles dappui permettent un levage
proessionnel en toute scurit.
autop Eurolift 2.30 Pv140-200, 160-220
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
14/62
...une entreprise du groupe STENHJ!
Et en plus....Nos technico-commerciaux se mettent votredisposition pour toutes demandes de planica-tion et modernisations.Veuillez nous contacter !
Eurolift 2.30 Pv
Composants:
Donnes techniques:
Capacit de levage: 3.000 kg
Espacement des cylindres: 1.335 mm
Course des vrins: 1.950 mm
Hauteur de levage: 2.020 mm
Dure de monte/descente: env. 30 sec.
Diamtre des cylindres: 2 x 123 mm
Proondeur de la ondation: 2.615 mm
Branchement: 400 V / 50 Hz/16 A
Groupe moto-pompe: 3,0 kW
2 vrins inverss en acier alli avec
surace chrome dure
Brides de guidage en aluminium coul
sous pression pour viter la corrosion
Commande lectronique
Descente durgence pneumatique
Barre fexible de synchronisation et de
scurit
Signal sonore au lieu de protecteurs
de piedsInstallation dans une cassette tanche
Livraison avec de lhuile cologique
Option:les ttes en xy augmentent le conort
et la plage de levage
Couleur standard:
galvanis chaud
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Sou
srservedemodifcationstechniques-position12/09
7/28/2019 AUTOP 2013
15/62
Le justechoix!
Le pont jumeaux autop Masterlit Pv ore un levage proessionnel dune grande
gamme de voitures.
Un levage rapide est donn par les plateaux ajustables en longueur et les patins
dappui stables assurent la scurit.
La barre de synchronisation exible et le contrle lectronique avec signalsonore reduisent la maintenance au minimum.
autop Masterlift 2.35 Pv / Pv xy120-180, 140-200, 160-220
...une entreprise du groupeSTENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
16/62
...une entreprise du groupe STENHJ!
Service:Nos technico-commerciaux vous assitent pourla planifcation et ralisation pour construc-tions neuves et de modernisations.Contactez-nous!
Masterlift 2.35Pv ou Pv xy
Composants:
Donnes techniques
Capacit de levage: 3.500 kg
Distance entre pistons: 1.335 mm
Course des vrins: 1.950 mm
Hauteur utilisable: 2.020 mm
Diamtre des cylindres: 2 x 123 mm
Monte/Descente: env. 30 sec.
Groupe moto-pompe: 3,0 kW
Proondeur ondation: 2.615 mm
Branchement: 230/400 V/50Hz/16A
Deux vrins inverses chroms-durs
Guides non-corrosis
Contrle lectronique
Descente durgence pneumatique
Dispositi de synchronisation/scurt
exible
Installation dans une cassette tanche
Huile cologique en standard
Option:Ttes en xy
Couleur standard:
Standard: galvanis chaud
Premium: galvanis et paint RAL
9006 blanc-aluminium
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
dition12/2011-Sousreservedemodifcations!
7/28/2019 AUTOP 2013
17/62
La formulepass-partout!
Le pont jumeaux Masterlit 2.35 Saav 135 dispose de bras double-tlescopiques
et peut tre ajust en longueur et largeur. Ainsi il est le pont le plus exible sur
le march utilisable de la petite voiture de ville la grande limousine, du tous-
terrains la vhicule utilitaire longue.Le grand choix de patins dappui assure un levage proessionnel et en tout s-
curit.
autop Masterlift 2.35 Saav 135
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
18/62
...une entreprise du groupe STENHJ!
Service:Nos technico-commerciaux vous assistentpour la planifcation et ralisation pour les con-structions neuves et des modernisations.Contactez-nous!
Masterlift 2.35Saav 135
Composants:
Donnes techniques
Capacit de levage: 3.500 kg
Distance entre pistons: 1.335 mm
Course des vrins: 1.950 mm
Hauteur utilisable: 2.045-2.370 mm
Patins standard: 2.045-2.085 mm
Diamtre des cylindres: 2 x 123 mm
Monte/Descente: env. 30 sec.
Groupe moto-pompe: 3,0 kW
Proondeur ondation: 2.615 mm
Branchement: 230/400 V/50Hz / 16A
Deux cylindres inverss chroms-durs
Guides non-corrosis
Contrle lectronique
Descente durgence pneumatique
Dispositi de synchronisation/scurt
exible
Installation dans une cassette tanche
Huile cologique en standard
Jeu de bras:
Double-tlescopiques Ajustables en largeur
Patins dappui ajustables en hau-
teur
Verrouillage automatique des bras
Option:
Grand choix de patins dappui
Couleur standard:
RAL 7016 ( gris-anthracite )
ou au choix
RAL 5019 ( bleu )
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
dition12/2011-Sousreservedemodifcations!
7/28/2019 AUTOP 2013
19/62
The hard-ware for your
bodyshop!
This lift allows a comfortable repair of damaged vehicles with a straightening
bench. The requirements for a body repair lift are:
free access to all sides of the vehicle
drive-in with a straightening bench without obstacle exible and variable swivel arms
comfortable lifting of the vehicle even with a straightening bench
security arm locking system
Very exible lift for body repair.
autop Masterlift 2.30 Sav 230
...a company of the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
20/62
...a company of th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning of a new garageor the modernization of an existing one. Weoer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Technical data:
Capacity: 3,000 kg
Piston distance: 2,285 mm
Cylinders diameter: 2 x 123 mm
Lifting/lowering time: appr. 30 sec.
Stroke length: 1,950 mm
Lifting height, dep. on lifting pads: 2,075-2,125 mm
Foundation depth: 2,615 mm
Voltage: 230/400 V
50 Hz
16 A
Power unit: 3.0 kW
Masterlift 2.30Sav 230
Standard colour:
RAL 7016 ( grey anthracite )
on request
RAL 5019 ( blue )
two hard-chromed hydraulic cylinders
corrosion-free guiding elementsSPS - control unit
pneumatic emergency drain
exible synchronizing and safety
device
installation in waterproof cassette
use of bio-oil, non hazardous to
water
two on-oor platforms with four
telescopic swivel arms on traverses,
in length adjustable, incl. four screw
pads 120 mm and height adjustable
125-175 mm
Components
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedforspecicationsthataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinformationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightofdierencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.
technicaldata,
equipment,materialandopticalappearance)sofarasthedierencesarereasonableforthecustomerandapossible
re
ductioni
nv
alue
ofthe
goodsdelivered
isnotconsiderable.
7/28/2019 AUTOP 2013
21/62
The rightchoice!
The autop Masterlit 2.35 Saa 135 Universal is a swivel arm lit which has been
designed especially or passenger cars, o-roaders and transporters.
The automatic and completely closed arm locking system oers a high level o
security.A wide range o liting pads assures a sae positioning and liting o dierent
types o cars with this autop lit; the double telescopic swivel arms make a big
liting area possible.
autop Masterlift 2.35 Saa 135
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
22/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weoer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Technical data:
Capacity: 3,500 kg
Piston distance: 1,335 mm
Cylinders diameter: 2 x 123 mm
Liting/lowering time: appr. 30 sec.
Stroke length: 1,950 mm
Liting height, dep. on liting pads: 2,045-2,370 mm
Standard: 2,045-2,085 mm
Foundation depth: 2,615 mm
Voltage: 230/400 V
50 Hz
16 APower unit: 3.0 kW
Masterlift 2.35Saa 135
Standard colour:
RAL 7016 ( grey anthracite )
on request
RAL 5019 ( blue )
two hard-chromed hydraulic cylinders
corrosion-ree guiding elementsSPS - control unit
pneumatic emergency drain
fexible synchronizing and saety
device
installation in waterproo cassette
use o bio-oil, non hazardous to
water
two on-foor swivel arm bridges with
double telescopic arms and height ad-
justable liting pads as well as integra-
ted automatic arm locking system
Components
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecifcationsthataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodierencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthedierencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable.
7/28/2019 AUTOP 2013
23/62
Le complmentpour votre atelier!
Le pont bras Masterlit 2.35 Saa 230 a t conu pour des voitures particulires,
des tous-terrains et des camionettes.
Les bras double-tlescopiques et la distance entre pistons de 2285 mm assurent
un accs acile et un levage proessionnel.
Le verrouillage automatique des bras est un systme erm qui protge contreendommagement.
Le grand choix de dirents patins dappui assure un levage en tout scurit.
autop Masterlift 2.35 Saa 230
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
24/62
...une entreprise du groupe STENHJ!
Service:Nos technico-commerciaux vous assistentpour la planication et ralisation pour les con-structions neuves et des modernisations.Contactez-nous!
Masterlift 2.35Saa 230
Composants:
Donnes techniques
Capacit de levage: 3.500 kg
Distance entre pistons: 2.285 mm
Course des vrins: 1.950 mm
Hauteur utilisable: 2.045-2.370 mm
Patins standard: 2.045-2.085 mm
Diamtre des cylindres: 2 x 123 mm
Monte/Descente: env. 30 sec.
Groupe moto-pompe: 3,0 kW
Proondeur ondation: 2.615 mm
Branchement: 230/400 V
50 Hz16 A
Deux cylindres inverss chroms-durs
Guides non-corrosis
Contrle lectronique
Descente durgence pneumatique
Dispositi de synchronisation/scurt
fexible
Installation dans une cassette tanche
Huile cologique en standard
Option:Grand choix de patins dappui
Couleur standard:
RAL 7016 ( gris-anthracite )
ou au choix
RAL 5019 ( bleu )
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
d
ition12/2011-Sousreservedemodifcations!
7/28/2019 AUTOP 2013
25/62
Le complmentpour votre atelier!
Le pont bras Masterlit 2.30 Sa 230 Sport avec sa distance entre pistons de
2285 mm trouve son application surtout dans le levage de voitures basses.
Les patins dappui avec une hauteur minimum de 70 mm sont paraits pour un
levage proessionnel mme pour des voitures sportives.
Un grand choix de dierents patins dappui permet une utilisation pour unegrande gamme de voitures particulires.
autop Masterlift 2.30 Sa 230
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
26/62
...une entreprise du groupe STENHJ!
Service:Nos technico-commerciaux vous assistentpour la planication et ralisation pour les con-structions neuves et des modernisations.Contactez-nous!
Masterlift 2.30Sa 230
Composants:
Donnes techniques
Capacit de levage: 3.000 kg
Distance entre pistons: 2.285 mm
Course des vrins: 1.950 mm
Hauteur utilisable: 2.020-2.370 mm
Diamtre des cylindres: 2 x 123 mm
Monte/Descente: env. 30 sec.
Groupe moto-pompe: 3,0 kW
Proondeur ondation: 2.615 mm
Branchement: 230/400 V /50Hz /16A
Deux cylindres inverss chroms-durs
Guides non-corrosis
Contrle lectronique
Descente durgence pneumatique
Dispositi de synchronisation/scurt
fexible
Installation dans une cassette tanche
Huile cologique en standard
Jeu de bras pivotants tlescopiques
avec hauteur min. rduite ( 70 mm )
Option:
Grand choix de patins dappui
Couleur standard:
RAL 7016 ( gris-anthracite )
ou au choix
RAL 5019 ( bleu )
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
dition07/2012-Sousreservedemodifcations!
7/28/2019 AUTOP 2013
27/62
For difcultinstallations!
Die autop Masterlit with electronic synchronisation is especially suitable or di-
cult installation situations such as installation in 400 mm drilled holes or plas-
tic tubes. The liting units are communicating electronically without mechanical
cylinder connection. Due to the exibility o the liting units individual pistondistances can be realized. No mechanical cylinder connection combined with a
sel-carrying cylinder construction means that various installations are possible:
ceiling installation
tube installation
pit installation
autop Masterlit 4.35 Synchro
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
28/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weofer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Technical data:
Capacity: 3,500 kg
Piston distance: exible mm
recommended 1,335/2,285
Cylinders diameter: 4 x 123 mm
Stroke length: 1,885 mm
Foundation depth: 2,390 mm
Voltage: 230/400 V
50 Hz
16 A
Power unit: 3.0 kW
Sel-supporting construction ( no support rom the bot-
tom necessary ) Suitable or drilled holes 400 mm.
Masterlit 4.35Synchro
OPTIONAL:
12071 at installation rame h=45 mm
12070 Pump unit attachment or ceiling
installation ML-Synchro (instal
lation o the pump unit at the
ceiling o the basement)12069 Pump unit-and control unit
column ( i installation on
the wall is not possible )
two pairs o inversed hydraulic cylin-
derscylinder running on teon rings
separated hydraulic circuits and
mechanical connection o the cylin-
ders o one side as saety device
together with the SPS-control unit
steel bearings in a sturdy welded
construction, galvanized and painted
push button control unit with syn-
chronization control, control o the
electronic limit switch and alarm
signal
distance between the cylinders
and the control unit up to max. 15 m
possible
with position sensor out o casted
electronic components and stainless
steel as electronical synchronization
device.
pump unit with sub-oil motor
can be combined with superstructu-
res autop Pv Premium- and swivel
arm superstructures with up to 3.5 t.
Components
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecicationsthataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodiferencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthediferencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable.
7/28/2019 AUTOP 2013
29/62
The prowants autop!
The model autop Masterlit Check-in has been improved and optimized. The
result is a new Check-in with still more unctionality or the reception area.
Also the design elements were taken into consideration.
The handy, pyramidal rubber pads assure a correct liting at the recommendedliting points.
Xy-heads increase the liting area considerably.
The hydraulic unit consists in proven components. The sychronizing/saety de-
vice is the most reliable on the market. The construction is simple and nearly
without any wear due to the well proven components.
autop Masterlift 2.35Combi Check-in
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
30/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weoer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Technical data:
Capacity: 3,500 kg
Stroke length platorms: 1,835 mm
Length platorms: 4,400 mm
Height platorms: 95 mm
Stroke length wheel-ree: 1,835 mm
Height wheel-ree: 65 mm
Piston distance: 1,335 mm
Cylinders diameter: 4 x 123 mm
Liting/lowering time: appr. 30 Sek
Foundation depth: 2,650 mm
Voltage: 230/400 V50 Hz
16 A
Power unit: 3.0 kW
Masterlift 2.35Combi Check-in
Standard colour:
RAL 7016 (grey anthracite)
aluminium plated
two separate hydraulic units
hard-chromed cylinderscorrosion-ree guiding elements
SPS - control unit
pneumatic emergency drain
fexible synchronizing and saety
device
illumination as standard equipment
installation in a waterproo cassette
use o bio-oil , non hazardous to
water
Installation possibilities:
- on-foor
- recessed in the foor
Components
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecifcationsthataresubjecttoalteration-validity07/2012.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodierencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthedierencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable.
7/28/2019 AUTOP 2013
31/62
Flexibility isthe key!
The Combi is a genuine all-purpose lit. A high quality and ecient diagnostic in
the check-in area is given due to the combination o platorm lit and wheel-ree
device Pv or Saav.
During repair works the platorms remain on-oor and the wheel-ree devicesallow nearly any kind or service work to be done.
Three installation versions are possible:
on-oor
recessed in the oor
recessed in the oor with ush-oor device
autop Masterlift 2.35 CombiPv or Saav
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
32/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weofer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Masterlift 2.35Combi Pv/Saav
Standard colour:
RAL 7016 ( grey anthracite )
on request
RAL 5019 ( blue )
two seperate hydraulic units
corrosion-ree guiding elementsSPS - control unit
pneumatic emergency drain
exible synchronizing and saety
device
installation in waterproo cassette
use o bio-oil, non hazardous to
water
platorms with anti-sliding surace
Wheel-ree device available:
Pv-superstructure ( standard or
with xy-unction )
Saav-superstructure
Components
Technical data
Capacity: 3.500 kg
Piston distance: 1,335/1,705 mm
PlatformStroke length: 1,905 mm
Liting/lowering time: appr. 35 sec.
Wheel-free device Pv/Saav
Stroke length: 1,905 mm
Liting/lowering time: appr. 35 sec.
Power unit: 3.0 kW
Voltage: 230/400 V
50 Hz
16 A
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecifcationsthataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodierencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthedierencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable.
7/28/2019 AUTOP 2013
33/62
Proessionaltechnology!
The technical advance o the Prolit consists in the pneumatic, electric and hy-
draulic supply inside o the cylinder and not in cable conduit tubes. The cylinder
dimensions o 140 x 9.5 mm increase the stability.
The platorm lits F 460 (without wheel-ree) and Fn 460 (with wheel-ree) con-sist in 2 on-oor sturdy welded platorms with special shaped proles, sand-
blasted, primed and painted; appropriate drive-on aps are available in dife-
rent lengths. Equipped with platorm supports and cross-bar the lit responds
perectly to the tolerances or wheel alignment.
The platorms can also be installed recessed in the oor with or without ush-
oor device.
autop Proflit 2.40 F and Fn 460
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
34/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weofer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Proflit 2.40F/Fn 460
Standard colour:
RAL 7016 ( grey anthracite )
on request
RAL 5019 ( blue )
two hard-chromed hydraulic cylinders
corrosion-ree guiding elementsSPS - control unit
pneumatic emergency drain
exible synchronizing and saety
device
installation in waterproo cassette
use o bio-oil, non hazardous to
water
platorms with anti-sliding surace
Possible installations:
on-oor
recessed in the oor
recessed in the oor with ush-
oor device
Optional:
illumination
accessories or wheel alignment
Components
Technical data
Capacity: 4.000 kgPiston distance: 1,315 mm
Stroke length: 1,960 mm
Liting height: 2,105 mm
Cylinder diameter: 2 x 140 mm
Liting/lowering time: appr.. 30 sec.
Pump unit: 3.0 kW
Foundation depth: 2,615 mm
Voltage: 230/400 V
50 Hz
16 A
Platorm:
Length: 4,600 mmWidth: 605 mm
Wheel-base, max.: 4,000 mm
Drive-over height: 150 mm
Wheel-ree (Fn460) Jacking beam (F460)
Capacity: 3.500 kg Capacity: 2,000 kg
Stroke length: 370 mm Stroke length: 250 mm
Length: 1400-2100 mm 3-ponts lting
Liting/lowering : appr. 8 sec. middle/ 660 / 1,340 mm
Drive-over height:25 mm
Liting height: 2,505 mm
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecicationsthataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodiferencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthediferencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable.
7/28/2019 AUTOP 2013
35/62
Proessionaltechnology!
Hydraulic twin-ram inground lit with platorms, wheel-ree device and integra-
ted play detector or check-in, repair and maintenance as well as MOT, testing
and reception.
Assessories: hydraulic play detector, integrated in the platorm on both sides
two turning plates working in counter rotation
control o the turning plate via test lamp
or a ast diagnostic o play in the wheel assembly
testing can be done even with a loaded vehicle by using the hydraulicly
controlled turning plates.
deposit or test lamp integrated in the platorm
autop Proflit 2.40 Fn 460GST 2500
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
36/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weoer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Proflit 2.40 Fn460 - GST 2500
Standard colour:
RAL 7016 ( grey anthracite )
on request
RAL 5019 ( blue )
two hard-chromed hydraulic cylinders
corrosion-ree guiding elementsSPS - control unit
pneumatic emergency drain
fexible synchronizing and saety
device
installation in waterproo cassette
use o bio-oil, non hazardous to
water
two on-foor platorms; appropriate
drive-on faps are available
platorms with anti-sliding surace
integrated scissor lit eective as
wheel-ree device
integrated play detector
Components
Technical data
Capacity: 4,000 kg
Piston distance: 1,315 mm
Stroke length: 1,960 mm
Liting height: 2,105 mm
Cylinder diameter: 2 x 140 mm
Liting/lowering time: appr. 30 sec.
Pump unit: 3.0 kW
Foundation depth: 2,615 mm
Voltage: 230/400 V
50 Hz
16 A
Platorm
Length: 4,600 mm
Width: 605 mmWheel-base, max.: 4,000 mm
Drive-over height: 150 mm
Wheel-ree device: GST:
Capacity: 3.500 kg Max. axle load: 2500 kg
Stroke length: 370 mm Drive-over height:150 mm
Length: 1400-2100 mm
Liting/lowering: ca. 8 Sek.
Drive-over height: 25 mmautop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecifcationsthataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodierencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthedierencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable.
7/28/2019 AUTOP 2013
37/62
Safety,leading to the
top!
The Cargolit with platorms has been developed or an ease liting o utility
vehicles with dierent chassis and wheel bases.
Possible accessories are:
illumination or the underbody platorms installed on-foor or recessed in the foor
wheel alignment
axle liting, also or long wheel bases
autop Cargolift 2.50 F 480
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
38/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weoer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Cargolift 2.50F 480
Standard colour:
RAL 7016 ( grey anthracite )
on request
RAL 5019 ( blue )
two hard-chromed hydraulic cylinders
corrosion-ree guiding elementsSPS - control unit
pneumatic emergency drain
fexible synchronizing and saety
device
installation in waterproo cassette
use o bio-oil, non hazardous to
water
two on-foor platorms, drive-on faps
are available
platorms with anti-sliding surace
Optional:
jacking-beam
illumination
wheel alignment package
Components
Technical data
Capacity: 5,000 kg
Piston distance: 1,465 mm
Stroke length: 1,750 mm
Liting height: 1,915 mm
Cylinders diameter: 2 x 140 mm
Liting/lowering time: appr. 45 sec.
Pump unit: 3.0 kW
Foundation depth: 2,665 mm
Anschlusswerte: 230/400 V
50 Hz
16 APlatform
Length: 4,800 mm
Width: 630 mm
Wheel-base, max.: 4,200 mm
Drive-over height: 165 mm
Jacking beam
Capacity: 2,600 kg
Liting height: 210 mm
3-points liting: middle/690-1500 mm
Function: air-hydraulic
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecifcationsthataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodierencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthedierencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable.
7/28/2019 AUTOP 2013
39/62
A realallrounder!
The swivel arm lit autop Cargolit 2.50 Saa 230 is appropriate or all commercial
vehicles up to little trucks i all-around ree access is demanded especially or
body repair works. This lit can also be used or any private cars and 4-wheels
drives i complementary capacities are needed.
The piston distance o 2,150 mm allows an easy access, the cars can be driven in
between the cylinders.
The solid construction with a cylinder diameter o 213 mm guarantees an out-
standing stability also in case o unavourable load distribution
A wide range o liting pads allows a sae liting o the dierent vehicles.
autop Cargolift 2.50 Saa 230
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
40/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weoer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Technical data:
Capacity: 5,000 kg
Piston distance: 2,150 mm
Cylinders diameter: 2 x 213 mm
Liting/lowering time: appr. 45 sec.
Stroke length: 1,865 mm
Liting height, dep. on liting pads
Standard: 2,010-2,070 mm
Foundation depth: 2,465 mm
Voltage: 230/400 V
50 Hz
16 APower unit: 3.0 kW
Cargolift 2.50Saa 230
Standard colour:
RAL 7016 ( grey anthracite )
on request
RAL 5019 ( blue )
two hard-chromed hydraulic cylinders
corrosion-ree guiding elementsSPS - control unit
pneumatic emergency drain
fexible synchronizing and saety
device
installation in waterproo cassette
use o bio-oil, non hazardous to
water
two on-foor swivel arm bridges, easy
to adjust:
double telescopic swivel arms
height adjustable liting pads
integrated automatic arm locking
system
Components
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecifcationsthataresubjecttoalteration-validity11/2012
.Thedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodierencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i
.e.technicaldata,
equipment,materialandopticalappearance)soarasthedierencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable
.
7/28/2019 AUTOP 2013
41/62
A realallrounder!
The swivel arm lit autop Cargolit 2.50 Jumbo is suitable or any kind o repair
and maintenance at light goods vehicles or little lorries i ree access is required.
The solid construction with a piston diameter o 213 mm guarantees an out-
standing stability also in case o unavourable load distributionO course this lit can also be used or private cars or o-roaders to compensate
ree capacities within your workshop.
A wide range o liting pads allows a sae liting o the dierent vehicles.
autop Cargolift 2.50 Saav 145
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
42/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weoer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Technical data:
Capacity: 5,000 kg
Piston distance: 1,350 mm
Cylinders diameter: 2 x 213 mm
Liting/lowering time: appr. 45 sec.
Stroke length: 1,865 mm
Liting height, dep. on liting pads
Standard: 2,010-2,070 mm
Foundation depth: 2,665 mm
Voltage: 230/400 V
50 Hz
16 APower unit: 3.0 kW
Cargolift 2.50Saav 145
Standard colour:
RAL 7016 ( grey anthracite )
on request
RAL 5019 ( blue )
two hard-chromed hydraulic cylinders
corrosion-ree guiding elementsSPS - control unit
pneumatic emergency drain
fexible synchronizing and saety
device
installation in waterproo cassette
use o bio-oil, non hazardous to
water
two on-foor swivel arm bridges, easy
to adjust:
sliding part on a traverse
double telescopic swivel arms
height adjustable liting pads
integrated automatic arm locking
system
Components
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecifcationsthataresubjecttoalteration-validity11/2012
.Thedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodierencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i
.e.technicaldata,
equipment,materialandopticalappearance)soarasthedierencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable
.
7/28/2019 AUTOP 2013
43/62
Une forceextraordinaire!
Le pont Biglit 2.65 Saaa 145 est un pont trs universel pour le levage dutilitaires
et de petits camions. Les vrins dun diamtre de 213 mm assurent un levage en
toute scurit avec des charges jusqu 6,5 t, mme en cas de repartition de la
charge davorable.
Une hauteur de passage rduite permet galement lutilisation pour desvoitures particulires et des 4 x 4.
La exibilit des bras triple-tlscopiques assure un maximum daccs autour
du vhicule pour toutes opration de rparation et de maintenance.
autop Biglift 2.65 Saaa 145
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
44/62
...une entreprise du groupe STENHJ!
Et en plus.........Nos technico-commerciaux se mettent votredisposition pour toutes demandes de planifca-tion et modernisations.Veuillez nous contacter !
Biglift 2.65Saaa 145
Composants:
Donnes techniques:
Capacit de levage: 6.500 kg
Espacement des cylindres: 1.350 mm
Course des vrins: 1.865 mm
Hauteur de levage: 1.960-2.285 mm
Dure de monte/descente: env. 45 sec.
Diamtre des cylindres: 2 x 213 mm
Proondeur de la ondation: 2.665 mm
Branchement: 400 V / 50 Hz /16 A
Groupe moto-pompe: 3,0 kW
2 vrins inverss (diamtre 213 mm) en
acier alli avec surace chrome dure
Brides de guidage en aluminium coul
sous pression pour viter la corrosion
Commande lectronique
Descente durgence pneumatique
Barre exible de synchronisation et de
scurit
Installation dans une cassette tanche
Livraison avec de lhuile cologiqueJeu de deux bras, aciles ajuster par :
Bras triple-tlscopiques
Patins dappui ajustables en hau-
teur
Verouillage des bras automatique
Couleur standard:
RAL 7016 (gris anthracite)
Au choix
RAL 5019 (bleu)
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Sou
srservedemodifcationstechniques-position12/09
7/28/2019 AUTOP 2013
45/62
Une forceextraordinaire!
Le pont Biglit 4.60 F 550 a t conu pour le levage rapide et simple des uti-
litaires avec des empattements trs dirents. Avec la capacit de levage de
6t et une longueur des chemins de roulement de 5,5 m mme des vhicules
utilitaires de la nouvelle gnration peuvent tre levs sans aucun problme.
Une hydraulique avec deux double-vrins inverss et cylindre et piston chroms
durs sont la base du pont. Les avantages sont :
Excution trs stable par doubles-vrins
Levage en scurit mme en cas de repartition de la charge davorable
Installation du pont cot reduit
Peut tre install dans des cassettes Cargolit existantes
Cylindres chroms durs (mini. 30 microns)
Besoin dun espace rduit
autop Biglift 4.60 F 550
...une entreprise du groupe STENHJ
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
46/62
...une entreprise du groupe STENHJ
Et en plus.........Nos technico-commerciaux se mettent votredisposition pour toutes demandes de planica-tion et modernisations.Veuillez nous contacter !
Biglift 4.60 F550
Composants:
Donnes techniques:
Capacit de levage: 6.000 kg
Espacement des cylindres: 1.485/145 mm
Course des vrins: 1.850 mm
Hauteur de levage: 2.065 mm
Dure de monte/descente: env. 45 sec.
Diamtre des cylindres: 4 x 123 mm
Proondeur de la ondation: 2.665 mm
Branchement: 400 V / 50 Hz /16 A
Groupe moto-pompe: 3,0 kW
Chemins de roulement :Longueur : 5.500 mm
Largeur : 630 mm
Empattement maxi : 4.900 mm
Hauteur de monte : 215 mm
2 doubles-vrins inverss en acier alli
avec surace chrome dure
Brides de guidage en aluminium coul
sous pression pour viter la corrosion
Commande lectronique
Descente durgence pneumatique
Barre fexible de synchronisation et de
scurit
Installation dans une cassette tanche
Livraison avec de lhuile cologiqueChemins de roulement avec surace
antidrapante
Couleur standard:
RAL 7016 (gris anthracite)
Au choix:
RAL 5019 (bleu)
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Sou
srservedemodifcationstechniques-position12/09
7/28/2019 AUTOP 2013
47/62
Une forceextraordinaire!
Le pont jumeaux Biglit 2.65 Saaa 230 a t conu pour la nouvelle gnrati-
on de vhicules utilitaires avec empattement trs long. Les bras triple-tlesco-
piques permettent lutilisation du pont pour le levage dune petite voiture de
ville, de toutes les voitures particulires, des tous-terrains ainsi que des grosses
camionettes.
La distance des pistons de 2.150 mm garanti un accs acile.
Le diamtre des cylindres de 213 mm donne une stabilit exemplaire surtout
pour le levage de grosses vhicules utilitaires.
autop Biglift 2.65 Saaa 230
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
48/62
...une entreprise du groupe STENHJ!
Service:Nos technico-commerciaux vous assistentpour la planication et ralisation pour les con-structions neuves et des modernisations.Contactez-nous!
Biglift 2.65Saaa 230
Composants:
Donnes techniques
Capacit de levage: 6.500 kg
Distance entre pistons: 2.150 mm
Course des vrins: 1.865 mm
Hauteur utilisable: 2.010-2.285 mm
Patins standard: 2.010-2.070 mm
Diamtre des cylindres 2 x 213 mm
Monte/Descente: env. 45 sec.
Groupe moto-pompe: 3,0 kW
Proondeur ondation: 2.665 mm
Branchement: 230/400 V /50 Hz /16 A
Deux cylindres inverss 213 mm
Guides non-corrosis
Contrle lectronique
Descente durgence pneumatique
Dispositi de synchronisation/scurit
fexible
Installation dans une cassette tanche
Huile cologique en standard
Bras pivotants triple-tlescopiques
Option:
Grand choix de patins dappui
Couleur standard:
RAL 7016 ( gris anthracite )
ou au choix
RAL 5019 ( bleu )
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
dition03/2012-Sousreservedemodifcations!
7/28/2019 AUTOP 2013
49/62
The key toyour success!
The autop Triolit is a proven team workstation or simultaneous work on three
levels: underbody o the vehicle, wheels and brakes, motor.
Fast service and repair as well as high rentability and space saving installtion
make this product outstanding.
The autop Triolit is known as
team workstation or quick-service
wheel alignment station or exact wheel alignment
autop Triolift 3.35 Fn 420
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
50/62
...a company o th e STENHJ-group!
Service:Our expert consultants would appreciate tohelp you with the planning o a new garageor the modernization o an existing one. Weoer to work out a workshop concept incl. anequipment proposal.Please do not hesitate to contact us!
Triolift 3.35Fn 420
Standard colour:
RAL 7016 ( grey anthracite )
on request
RAL 5019 ( blue )
two hydraulic cylinders made o mic-
ro-alloyed high grade steelwith hard-chrome plated pistons
security device by rigid bearing at the
working platorm
push button control or liting/lowe-
ring o platorms and wheel-ree de-
vice
working platorm with control column
and tool deposit
two on-oor platorms o sturdy wel-
ded design with special shaped prof-
les, sand-blasted, primed and painted;
with corresponding drive-on aps
platorms with anti-sliding surace
integrated hydraulic scissor lit with
low drive-over height or simultaneous
wheel-ree liting on all our wheels
Components
Technical data
Capacity: 3,500 kg
Platforms
Stroke length: 650 mm
Liting/lowerng time: appr. 5 sec.
Length: 4,200 mm
Width: 570 mm
Between platorms: 905 +/- 70 mm
Drive-on angle: 5
Wheel-free device
Stroke length: 370 mm
Liting/lowering time: ca. 8 Sek.
Length: 1,400-2,100 mm
Working platform
Depth: 1,060 mm
Pit
Length: 4,980 mm
Width: 990 mm
Depth: 900-950 mm
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
Noliabilityacceptedorspecifcationsthataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapproximatedescription.
Moreoverwereservethe
rightodierencesbetweenthegoodsdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthedierencesarereasonableorthecustomerandapossible
re
ductioninvalueothegoodsdeliveredisnotconsiderable.
7/28/2019 AUTOP 2013
51/62
Une technolgiepassionnante!
Le double pont jumeaux ore une prcision exemplaire pour la gomtrie. Il est
quip avec des reserves lavant et larrire qui permettent lutilisation de
toutes les appareillages de gomtrie modernes, soit avec 4 plaques tournan-
tes, soit avec 2 plaques tournantes et 2 plaques pivotantes larrire.
Avec loption cric dessieu vous pouvez lever tous les vhicules, mme avec des
dessous de caisses compliqus.
autop Quattrolift 4.50 F 480 / 550Gomtrie
...une entreprise du groupe STENHJ!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
52/62
...une entreprise du groupe STENHJ!
Service:Nos technico-commerciaux vous assitentpour la planication et ralisation pour cons-tructions neuves et de modernisations.Contactez-nous!
Donnes techniques
Capacit de levage: 5,000 kg
Distance des pistons: 1,685/4,000 mm
Diamtre des cylindres: 4 x 140 mmMonte/Descente: env. 45 sec
Course des vrins: 1,960 mm
Hauteur utilisable: 2,155 mm
Proondeur ondation: 2,625 mm
Branchement: 230/400 V/50Hz /16A
Groupe moto-pompe: 3.0 kW
Chemins des roulement:
Longeur (F480): 4,800 mm
Longeur (F550): 5,500 mm
Largeur: 650 mm
Empattement maxi: 4,850 mmHauteur de monte: 195 mm
Levage auxiliare mobile:
Capacit de levage: 2,600 kg
Hauteur de levage: 300 mm
Monte
( avec air 1000/2000kg): env. 27/52 sec
Pression (min/max) 5.5/8.0 bar
Quattrolift 4.50F 480/550
Couleur standard
RAL 7016 ( gris anthracite )
ou au choix
RAL 5019 ( bleu )
2 units de levage spares avec 4
cylindres inversesCylindres chroms-durs
Guides non-corrosis
Contrle lectronique avec achage
digital et descente durgence pneu-
matique
Dispositis des synchronisation/scuri-
t fexible
Synchronisation lectronique des
deux units de levage avec program-
mation des dierentes hauteurs.
Installation dans des cassettes tan-
ches
Installation du groupe moto-pompe
et de la distribution hydraulique dans
une cassette spare
Huile cologique en standard
Chemins de roulement avec surace
anti-glissante
Composants:
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
dition12/2011-Sousreservedemodifcations!
7/28/2019 AUTOP 2013
53/62
No. Item Designation1 11007 Insert pads U 102 11014 Insert pads Ro
jacking beam3 11029 Insert pads 12
4 11031 Pv pads 120 / 5 11000 Rubber blocs 806 11001 Rubber blocs 607 11004 Rubber blocs 108 S1014-50 Adapter Monde9 11005 Rubber plate 20
No. Item Designation1 11027 Insert pad 2 11029 Insert pad 3 11030 Insert pad 4 11014 Insert pad
jacking bea5 11013 Insert pad s6 11006 Insert pad U7 11021 Insert pad U
11007 Insert pad U11009 Insert pad U37940 Support for 11028 Insert pad 11100 Wall mounte
(delivery wit
Accessories for autop lifts
1
2
3
4
75
6
8
9
7/28/2019 AUTOP 2013
54/62
Nr. Item Designation11025 Traverse, fo
1 set = 2 pie
Attention: Lifting pads to be orde
Nr. Item Designation20930 Jacking bea
for autop pl
Accessories for autop lifts
7/28/2019 AUTOP 2013
55/62
Nr. Item Designation12233 Jacking bea
for autop pl
Nr. Item Designation12221 Platform su
Fn 420, F480H 1 = 160H 2 = 600 H 3 = 1600
12222 Platform su420, Fn 420,H 1 = 160H 2 = 1600
Accessories for autop lifts
7/28/2019 AUTOP 2013
56/62
Nr. Item Designation1 12275 Cassette 132 12276 Cassette 233 12226 Cassette Co
4 12192 Cassette 14
Nr. Item Designation1 12007 Cassette for
With integra2 12006 Cassette for
Ceiling insta3 12005 Stahlwanne
With wall-m
Nr. Item Designation1 S0728 Cassette KA
Self-carryin2 S0729 Cassette KA
Self-carryin
3 S0750 Cassette KASelf-carryin
4 S0526 Plastic coat1350 / 1450
5 S0527 Plastic coat1705 / 2300
Accessories for autop lifts
7/28/2019 AUTOP 2013
57/62
Nr. Item Designation1 11060 XY-heads2 11062 XY-heads fo
Nr. Item Designation1 12239 Cross-bar 2 12240 Cross bar
Querstrebe
Accessories for autop lifts
7/28/2019 AUTOP 2013
58/62
Nr. Item Designation1 12181 Foundation
for tube ins2 12183 Foundation
for tube ins3 12197 Foundation
for tube ins
Nr. Item Designation1 12162 Flat foundat2 12163 Flat foundat3 12179 Flat foundat4 12238 Flat foundat
Accessories for autop lifts
7/28/2019 AUTOP 2013
59/62
3
3
4
4
5
5
6
6
A
B
C
D
Schutzv
der N
NameZust. nderung
DIN IS
Freigabe
Ersteller
m
EDV Datum
X
Radgreiferaufnahme
Detailansicht vomAufnahmedorn
Radgreiferaufnahme "OEntwickelt fr die SUV- zur Aufnahme von Fahrz
7/28/2019 AUTOP 2013
60/62
http://www.autop.de/mailto:mail@autop.de7/28/2019 AUTOP 2013
61/62
Cleanerthan ever!
The Jet-Cleaners oers:
easy handling
automatic operation the possibility o programming or working days, week-ends and holidays
cleaning on the basis o water
longer lietime o washing liquid, i equipped with an oil skimmer
minimum operation costs due to economy isolation
autop Jet CleanerRC 82 and RC 122
...a company o the STENHJ-group!
autop Maschinenbau GmbH
Sandkampstr. 90
D-48432 Rheine
Tel. ++49(0)5971/8602-02
Fax ++49(0)5971/8602-25
E-Mail: mail@autop.de
www.autop.de
7/28/2019 AUTOP 2013
62/62
Jet CleanerRC 82 / 122
Standard colour:
RAL 7016 ( grey anthracite ) - housing-
RAL 1004 ( yellow ) - cover
Standard:
made o stainless steellow-water alarm
suction flter made o stainless steel
bath cover
movable
Optional:
programmable operation time
oil skimmer
economy insulation
special colour
detergents, baskets, etc.
Components
Technical data RC 82 RC122
Useul basket : 790 mm 1,190 mm
Useul height: 500 mm 500 mm
Loading height: 930 mm 830 mm
Max. basket load: 300 kg 500 kg
Liquid volume: 150 l 370 l
Pump ration: 200 l/min 280 l/min
Projection pressure: 3 bar 5 bar
Voltage: 230/400 V/50 Hz 230/400 V/50 Hz
14 A 24 A
Pump motor rating: 1,5 kw 4 kW
Heater rating: 6 kw 9+6 kW
Basket drive: jet o water E-motor 0,09 kW
Total height: appr. 1200 mm appr. 1250 mm
Total width: appr. 1300 mm appr. 1650 mm
Total depth: appr. 1300 mm appr. 1650 mm
Total weight: appr. 220 kg appr. 400 kgth
ataresubjecttoalteration-validity07/2011.T
hedateandpicturesinthisproductinormationarenotbindingandareonlygivinganapprox
imatedescription.Moreoverwereservethe
sdeliveredandthedateandpicturesgivenhere(i.e.technicaldata,equipment,materialandopticalappearance)soarasthedierencesarere
asonableorthecustomerandapossible
redisnotconsiderable.
Recommended