View
17
Download
0
Category
Preview:
Citation preview
<WCDMA TX Minimum Power measurements using ARB files on the R&S CMW 500> Application Note
Products:
| R&SCMW500
| R&SCMW-KW400
| R&SCMW-KM400
<App
licati
onNo
te>
<Tho
masL
utz>
<05.2
010-
1CM8
0>-<
versi
on0.1
>
Table of Contents
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 2
Table of Contents 1 Test Equipment Setup ........................................................... 4 1.1 R&S CMW500 WCDMA Arbitrary Waveform Playback Setup.................4 1.1.1 Step 1 – Enable the General Purpose RF Generator ................................4 1.1.2 Step 2 – Configure the General Purpose RF Generator ...........................4 1.1.3 Step 3 – Select the ARB File........................................................................5 1.1.4 Step 4 – Turn ON the General Purpose RF Generator..............................6 1.1.5 – Table of the General Purpose RF Generator Settings...........................7 1.1.6 Rohde & Schwarz WCDMA Non-signaling test arbitrary waveform
configuration.................................................................................................7 1.1.7 Rohde & Schwarz WinIQSIM2 control sequence ......................................8 1.1.7.1 Reset the tool................................................................................................8 1.1.7.2 Defining the scrambling code.....................................................................9 1.1.7.3 Primary CPICH definition.............................................................................9 1.1.7.4 Secondary CPICH definition (inactive).......................................................9 1.1.7.5 Primary SCH definition ................................................................................9 1.1.7.6 Secondary SCH definition ...........................................................................9 1.1.7.7 Primary CCPCH definition ...........................................................................9 1.1.7.8 Secondary CCPCH definition (inactive) ...................................................10 1.1.7.9 PICH definition............................................................................................10 1.1.7.10 AICH definition (inactive)...........................................................................10 1.1.7.11 AP_AICH definition (inactive)....................................................................10 1.1.7.12 PDSCH definition (inactive).......................................................................10 1.1.7.13 Downlink DPCCH definition (inactive) .....................................................10 1.1.7.14 DPCH definition ..........................................................................................11 1.1.7.15 Definition of all other channels (12 to 137)..............................................11 1.1.7.16 Marker definition.........................................................................................11 1.1.7.17 ARB Length.................................................................................................12 1.1.7.18 Query for the relative total power.............................................................12 1.1.7.19 Query for channel conflicts, syntax errors in the remote sequence ....12 1.1.7.20 Creation of the arbitrary waveform file ...................................................12 1.1.8 R&S CMW500 Configuration for WCDMA Uplink Signal Measurement12 1.1.9 Multi Evaluation Settings...........................................................................13 1.1.10 RF Settings..................................................................................................14
Table of Contents
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 3
1.1.11 Measurement Control ................................................................................16 1.1.11.1 Repetition ....................................................................................................16 1.1.11.2 Stop Condition............................................................................................17 1.1.11.3 Statistic Counts ..........................................................................................17 1.1.11.4 Measurement Length .................................................................................17 1.1.11.5 Assign View ................................................................................................18 1.1.12 Start the Measurement...............................................................................18 1.1.13 Measurement Results Screen Shots ........................................................19 1.1.14 Automating a WCDMA Measurement with the R&S CMW500..............19 1.1.14.1 Configure the arbitrary signal generator to play the waveform ............19 1.1.14.2 Configure the R&S CMW500 analyzer to make a WCDMA measurement
......................................................................................................................20 1.1.14.3 Arm the measurement ...............................................................................20 1.1.14.4 Get the modulation measurement results ...............................................20
2 Summary............................................................................... 21
3 References............................................................................ 21
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 4
1 Test Equipment Setup
1.1 R&S CMW500 WCDMA Arbitrary Waveform Playback Setup
The following details how to configure the R&S CMW500 General Purpose RF Generator for playback of an arbitrary waveform used for WCDMA non-signaling TX measurements at minimum power. The waveform to execute playback on is:
• D:\Rohde-Schwarz\CMW\Data\waveform\RMC12_2_Min_0_9_04.wv
To start this arbitrary waveform file a software option KW400 on the R&S CMW500 is required
1.1.1 Step 1 – Enable the General Purpose RF Generator
1.1.2 Step 2 – Configure the General Purpose RF Generator
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 5
1.1.3 Step 3 – Select the ARB File
To select the arbitrary waveform, press the ARB soft key on left side of R&S CMW screen, followed by the “Select ARB File …” soft key on the bottom
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 6
Navigate through the pop up dialog, e.g. rotating the spin wheel and select the desired arbitrary waveform file by pushing the spin wheel. Navigate the focus of the dialog to the OK button by rotating the spin wheel again. After selecting the OK button push the spin wheel again
1.1.4 Step 4 – Turn ON the General Purpose RF Generator
To begin playing the arbitrary waveform, press the On/Off hard key button on the R&S CMW500 front panel, located along the top of the instrument, above the spin wheel.
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 7
1.1.5 – Table of the General Purpose RF Generator Settings
General Purpose RF Generator RF Configuration Parameter Settings Units
RF Routing User defined (suggest RF1 COM)
External Attenuation User defined (RF cable path loss) dB
Frequency 2112.4 MHz
Level (RMS) -65.0 dBm
Digital Gain 0.0 dB
List Mode Off
Baseband Configuration Baseband Mode ARB
Dual Tone Not applicable
ARB Configuration Repetition Continuous
ARB File Name D:\Rohde-Schwarz\CMW\Data\waveform\ RMC12_2_Min_0_9_04.wv
Trigger Retrigger Checked
Autostart Checked
Source Not applicable
List Configuration List Elements Not applicable
1.1.6 Rohde & Schwarz WCDMA Non-signaling test arbitrary waveform configuration
The waveform described below is useful for testing WCDMA chipsets in non-signaling test mode using the Rohde & Schwarz CMW500 Wideband Radio Communication Tester. The signal provides everything needed in a downlink signal for a non-signaling test mode enabled device to synchronize and decode on downlink channel 10562. The signal can be used to perform minimum power TX measurements on the R&S
CMW 500. Changing the ARB file will cause the mobile to loose the synchronization. To prevent this, a multi-segment ARB generator mode is available on the R&S
CMW500.
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 8
Uplink signal measurements from the chip can be performed using the R&S CMW500 WCDMA measurement option, KM400. Waveform file name: RMC12_2_Min_0_9_04.wv Waveform Content 40 millisecond long waveform (4 frames equal to 1 TTI)
DL Primary Scrambling Code 0
DL Secondary Scrambling Code 0
DPCH Channel Code 9
Channel type 12.2kbps RMC
Power Control Bits set all to ‘1’
P-CPICH Level -3.3 dB
P-SCH Level -8.3 dB
S-SCH Level -8.3 dB
P-CCPCH Level –5.3 dB
PICH Level -8.3 dB
DPCH Level -10.3 dB
1.1.7 Rohde & Schwarz WinIQSIM2 control sequence
The Rohde & Schwarz tool WinIQSIM2 can also be remote controlled to define the parameters, which are used to generate the arbitrary waveform file. The remote interface behaves like a standard remote interface of a signal generator based on a SCPI syntax using an VISA driver to control a TCP/IP connection to “localhost”. The leading “WinIQSIM: ” is not part of the command, this is only used as a address symbol in this Rohde & Schwarz remote script tools
1.1.7.1 Reset the tool
buffout = [ ] WINIQSIM2: *IDN? WINIQSIM2: *RST WINIQSIM2: *CLS WINIQSIM2: BB:W3GP:STAT OFF
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 9
1.1.7.2 Defining the scrambling code
The primary scrambling code is defined with 4 digits followed by the secondary scrambling code with 1 digit
1.1.7.3 Primary CPICH definition
1.1.7.4 Secondary CPICH definition (inactive)
1.1.7.5 Primary SCH definition
1.1.7.6 Secondary SCH definition
1.1.7.7 Primary CCPCH definition
WINIQSIM2: BB:W3GP:BST1:CHAN4:STAT ON WINIQSIM2: BB:W3GP:BST1:CHAN4:POW -5.3 WINIQSIM2: BB:W3GP:BST1:CHAN4:CCOD 1 WINIQSIM2: BB:W3GP:BST1:CHAN4:DATA PN9 WINIQSIM2: BB:W3GP:BST:ENH:PCCP:CCOD:STAT ON WINIQSIM2: BB:W3GP:BST:ENH:PCCP:STAT ON
WINIQSIM2: BB:W3GP:BST1:CHAN3:STAT ON WINIQSIM2: BB:W3GP:BST1:CHAN3:POW -8.3
WINIQSIM2: BB:W3GP:BST1:CHAN2:STAT ON WINIQSIM2: BB:W3GP:BST1:CHAN2:POW -8.3
WINIQSIM2: BB:W3GP:BST1:CHAN1:STAT OFF WINIQSIM2: BB:W3GP:BST1:CHAN1:POW -3.3 WINIQSIM2: BB:W3GP:BST1:CHAN1:CCOD 7
WINIQSIM2: BB:W3GP:BST1:CHAN0:STAT ON WINIQSIM2: BB:W3GP:BST1:CHAN0:POW -3.3
WINIQSIM2.write('BB:W3GP:BST1:SCOD #H0000') WINIQSIM2: BB:W3GP:BST1:SCOD:STAT ON
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 10
1.1.7.8 Secondary CCPCH definition (inactive)
1.1.7.9 PICH definition
1.1.7.10 AICH definition (inactive)
1.1.7.11 AP_AICH definition (inactive)
1.1.7.12 PDSCH definition (inactive)
1.1.7.13 Downlink DPCCH definition (inactive)
WINIQSIM2: BB:W3GP:BST1:CHAN10:STAT OFF
WINIQSIM2: BB:W3GP:BST1:CHAN9:STAT OFF
WINIQSIM2: BB:W3GP:BST1:CHAN8:STAT OFF
WINIQSIM2: BB:W3GP:BST1:CHAN7:STAT OFF WINIQSIM2: BB:W3GP:BST1:CHAN7:POW -8.3 WINIQSIM2: BB:W3GP:BST1:CHAN7:CCOD 2
WINIQSIM2: BB:W3GP:BST1:CHAN6:STAT ON WINIQSIM2: BB:W3GP:BST1:CHAN6:POW -8.3 WINIQSIM2: BB:W3GP:BST1:CHAN6:CCOD 16 WINIQSIM2: BB:W3GP:BST1:CHAN6:DATA PN9 WINIQSIM2: BB:W3GP:BST1:CHAN6:TOFF 0
WINIQSIM2: BB:W3GP:BST1:CHAN5:STAT OFF WINIQSIM2: BB:W3GP:BST1:CHAN5:POW -5.3 WINIQSIM2: BB:W3GP:BST1:CHAN5:CCOD 4 WINIQSIM2: BB:W3GP:BST1:CHAN5:DATA PN9 WINIQSIM2: BB:W3GP:BST1:CHAN5:SFOR 4 WINIQSIM2: BB:W3GP:BST1:CHAN5:TOFF 0
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 11
1.1.7.14 DPCH definition
The code channel is 9. It is using aRMC12.2 coded channel with transport format combination index 3. The data source is a PRBS-9 sequence TPC bits set continuously to zero.
1.1.7.15 Definition of all other channels (12 to 137)
1.1.7.16 Marker definition
1 = ARB length 2 = ARB length 3 = Slot 4 = Frame
WINIQSIM2: SOUR:BB:W3GP:TRIG:OUTP1:MODE CSP WINIQSIM2: SOUR:BB:W3GP:TRIG:OUTP2:MODE CSP WINIQSIM2: SOUR:BB:W3GP:TRIG:OUTP3:MODE SLOT WINIQSIM2: SOUR:BB:W3GP:TRIG:OUTP4:MODE RFR
for index in range (12, 138): buffout = "BB:W3GP:BST1:CHAN" + str(index) + ":STAT OFF" WINIQSIM2.write(buffout) buffout = "BB:W3GP:BST1:CHAN" + str(index) + ":POW 0.0" WINIQSIM2.write(buffout) buffout = "BB:W3GP:BST1:CHAN" + str(index) + ":TOFF 0" WINIQSIM2.write(buffout)
WINIQSIM2: BB:W3GP:BST1:CHAN11:STAT ON WINIQSIM2: BB:W3GP:BST1:CHAN11:POW -10.3 WINIQSIM2: BB:W3GP:BST1:CHAN11:CCOD 9 WINIQSIM2: BB:W3GP:BST1:CHAN11:DATA PN9 WINIQSIM2: BB:W3GP:BST1:CHAN11:TOFF 0 WINIQSIM2: BB:W3GP:BST:ENH:CHAN11:DPCH:CCOD:TYPE M12K2 WINIQSIM2: BB:W3GP:BST:ENH:CHAN11:DPCH:CCOD:STAT ON WINIQSIM2: BB:W3GP:BST:ENH:CHAN11:DPCH:STAT ON WINIQSIM2: BB:W3GP:BST:ENH:CHAN11:DPCH:TCH1:DATA PN9 WINIQSIM2: BB:W3GP:BST1:CHAN11:DPCC:TFCI 3 WINIQSIM2: BB:W3GP:BST1:CHAN11:DPCC:TFCI:STATE ON WINIQSIM2: BB:W3GP:BST1:CHAN11:DPCC:TPC:DATA ZERO WINIQSIM2: BB:W3GP:BST1:CHAN11:DPCC:TPC:READ CONT
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 12
1.1.7.17 ARB Length
Defined with number of frames
1.1.7.18 Query for the relative total power
1.1.7.19 Query for channel conflicts, syntax errors in the remote sequence
1.1.7.20 Creation of the arbitrary waveform file
1.1.8 R&S CMW500 Configuration for WCDMA Uplink Signal Measurement
The following describes how to configure the R&S CMW500 to perform a measurement on the uplink WCDMA transmitter. First, enable the WCDMA TX Measurement option on, by checking its enable radio button from the Measurement Controller sub panel. This menu can be found by pressing the Measure hard key found along the top of the R&S CMW500 front panel, above the number keypad.
WINIQSIM2: SOUR:BB:W3GP:WAV:CRE "e:\RMC12_2_Min_0_9_04.wv" WINIQSIM2: SYST:ERR?
WINIQSIM2: BB:W3GP:BST1:DCON? WINIQSIM2: SYST:ERR?
WINIQSIM2: BB:W3GP:SLEN 4 WINIQSIM2: BB:W3GP:STAT ON;*OPC?
WINIQSIM2: BB:W3GP:POW?
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 13
1.1.9 Multi Evaluation Settings
Next find and press the following soft key on from the R&S CMW500 WCDMA TX Measurement – Multi Evaluation screen. If this soft key is not yet visible, use the Tasks hard key.
The Tasks hard key shows the available currently enabled (loaded) software features and to select this feature. Press the soft key “WCDMA Multi Eval.”
The displayed soft keys row along the bottom of the LCD display should change to one of the WCDMA Multi Evaluation controls like shown below.
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 14
1.1.10 RF Settings
Press the “Config…” on the right side of the displayed soft keys row along the bottom of the LCD display. You should see the shown pop up menu now.
The following screen shots detail how to configure the following parameters to these values:
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 15
WCDMA Measurements RF Configuration Parameter Settings Units
RF Routing User defined (suggest RF1 COM)
External Attenuation User defined (RF cable path loss) dB
Frequency 1922.4 MHz
Expected Power Level (RMS) -35.0 dBm
User Margin 6.0 dB
List Mode Off
Trigger Trigger Source Free Run (Standard)
Trigger Timeout 2000 (default) msec.
Minimum Trigger Gap 25 (default) µsec.
Multi Evaluation Configuration Measurement Length 1 slot
Statistic Counts Power 1 Slot
Modulation 5 Slots
ACLR Spectrum Not applicable Slots
Spectrum Emission Mask Not applicable Slots
BER Not applicable Blocks
List Configuration List Elements Not applicable
Press the soft key “Config…” again to come back to the measurement screen. The R&S CMW500 LCD screen should look like the following:
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 16
1.1.11 Measurement Control
Find and press the following soft key on the right-hand column of the LCD screen.
Configure the remaining parameters by manipulating the soft keys as such:
1.1.11.1 Repetition
Set the repetition mode to “Continuous”
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 17
1.1.11.2 Stop Condition
Set the stop condition to “None”
1.1.11.3 Statistic Counts
1.1.11.4 Measurement Length
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 18
1.1.11.5 Assign View
Press the soft key “Assign Views…” to select the TX measurements of your interest.
1.1.12 Start the Measurement
The measurement can be manually executed (triggered) by pressing the ON/OFF hard key on the front panel of the R&S CMW500, located along the top of the instrument, above the spin wheel.
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 19
1.1.13 Measurement Results Screen Shots
A successful WCDMA multi-evaluation measurement on the R&S CMW500 should look something like found on the following screen shot.
1.1.14 Automating a WCDMA Measurement with the R&S CMW500
The following SCPI command code is an example of how to configure the R&S
CMW500 signal generator and signal analyzer to perform a non-signaling WCDMA uplink TX measurement on non signaling enabled WCDMA chipset. The leading “CMW: ” is not part of the command, this is only used as a address symbol in Rohde & Schwarz remote script tools.
1.1.14.1 Configure the arbitrary signal generator to play the waveform
Whenever loading an ARB file, you should ensure it was present on the selected path. The verification can be achieved by querying the currently loaded ARB file. A return string "No File Selected" would be an indication, that the file is not present.
Test Equipment Setup
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 20
1.1.14.2 Configure the R&S CMW500 analyzer to make a WCDMA measurement
1.1.14.3 Arm the measurement
1.1.14.4 Get the modulation measurement results
CMW: FETC:WCDM:MEAS:MEV:MOD:AVER?
CMW: INIT:WCDM:MEAS:MEV;*OPC?
CMW: ROUT:WCDM:MEAS:RFS:CONN RF1C CMW: CONF:WCDM:MEAS:RFS:EATT 1 CMW: CONF:WCDM:MEAS:RFS:FREQ 1922.4e6 CMW: CONF:WCDM:MEAS:RFS:ENP -35 CMW: CONF:WCDM:MEAS:RFS:UMAR 6 CMW: CONF:WCDM:MEAS:UES:SCOD 0 CMW: CONF:WCDM:MEAS:UES:SFOR 0 CMW: CONF:WCDM:MEAS:UES:ULC WCDMA CMW: CONF:WCDM:MEAS:UES:DPDC ON CMW: CONF:WCDM:MEAS:MEV:REP SING CMW: CONF:WCDM:MEAS:MEV:RES:ALL OFF,OFF,OFF,OFF,OFF,OFF,OFF,OFF,OFF,OFF,OFF,ON,OFF,OFF,OFF, OFF,OFF,OFF CMW: CONF:WCDM:MEAS:MEV:MSC 1 CMW: CONF:WCDM:MEAS:MEV:SCO:MOD 5 CMW: CONF:WCDM:MEAS:MEV:MPER:MOD FULL CMW: TRIG:WCDM:MEAS:MEV:SOUR 'Free Run (Standard)'
CMW: ROUT:GPRF:GEN1:RFS:CONN RF1C CMW: SOUR:GPRF:GEN1:BBM ARB CMW: SOUR:GPRF:GEN1:RFS:FREQ 2112.4e6 CMW: SOUR:GPRF:GEN1:RFS:EATT 1 CMW: SOUR:GPRF:GEN1:RFS:LEV -65 CMW: SOUR:GPRF:GEN1:ARB:FILE 'd:\\Rohde-Schwarz\\CMW\\data\\waveform\\RMC12_2_Min_0_9_04.wv' CMW: SOUR:GPRF:GEN1:ARB:FILE? CMW: SOUR:GPRF:GEN1:ARB:REP CONT CMW: TRIG:GPRF:GEN1:ARB:RETR ON CMW: TRIG:GPRF:GEN1:ARB:AUT ON CMW: SOUR:GPRF:GEN1:LIST OFF CMW: SYST:ERR? CMW: SOUR:GPRF:GEN1:STAT ON;*OPC?
Summary
<1CM80_0E> Rohde & Schwarz < WCDMA TX Minimum power measurements, using ARB files on the R&SCMW 500> 21
2 Summary The application note explains how to create and use an arbitrary waveform file to perform typical WCDMA transmitter tests at minimum Tx power for a non-signaling test mode enabled device.
3 References [1] User manual of the R&S CMW 500 or R&S CMW 280 radio communication
tester. [2] Software manual for the R&S WinIQSim Simulation Software [3] Software manual for the R&SWinIQSim Options xxx-K42/ -K242/ -K43/ -
K243/ -K45/ -K245/ -K59/ -K259/ -KW401/ -KW402 3GPP FDD, HSDPA, HSUPA and HSP
Index A
Arm the WCDMA Measurement............................................... 20 Automating a WCDMA Measurement ...................................... 19
CConfigure the ARB generator................................................... 19 Configure the GPRF Generator.................................................. 4 Configure the WCDMA analyzer .............................................. 20
E
Enable the GPRF Generator...................................................... 4
G
Get the WCDMA modulation measurement results .................. 20
M
Measurement Control .............................................................. 16
Multi Evaluation Settings ..........................................................13
R
RF Settings of the WCDMA Measurement................................14
SSelect the ARB File ....................................................................5 Start the WCDMA Measurement ..............................................18
TTable of the GPRF Generator Settings .......................................7 Turn On the GPRF Generator..................................................6,8
W
WCDMA Measurement Result Screen Shot..............................19 WCDMA Uplink Measurements ................................................12
About Rohde & Schwarz Rohde & Schwarz is an independent group of companies specializing in electronics. It is a leading supplier of solutions in the fields of test and measurement, broadcasting, radiomonitoring and radiolocation, as well as secure communications. Established 75 years ago, Rohde & Schwarz has a global presence and a dedicated service network in over 70 countries. Company headquarters are in Munich, Germany.
Environmental commitment ● Energy-efficient products ● Continuous improvement in
environmental sustainability ● ISO 14001-certified environmental
management system
Regional contact
USA & Canada USA: 1-888-TEST-RSA (1-888-837-8772) from outside USA: +1 410 910 7800 CustomerSupport@rohde-schwarz.com
East Asia +65 65 13 04 88 CustomerSupport@rohde-schwarz.com
Rest of the World +49 89 4129 137 74 CustomerSupport@rohde-schwarz.com
This application note and the supplied programs may only be used subject to the conditions of use set forth in the download area of the Rohde & Schwarz website.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG. Trade names are trademarks of the owners.
Rohde & Schwarz GmbH & Co. KG Mühldorfstraße 15 | D - 81671 München Phone + 49 89 4129 - 0 | Fax + 49 89 4129 – 13777 www.rohde-schwarz.com
Recommended