View
101
Download
12
Category
Tags:
Preview:
DESCRIPTION
Ansys Mechanical APDL lecture 2 by Haydar Alsalami from IRAQ - Hilla, studied in JNTUH - INDIA . haydar2200@gmail.com - mobile : 00919059070644 - 009647801518389
Citation preview
1 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
- We can make REFRESH for ANSYS by pressing: Ctrl+Shift+Delete.
- In the drawing of a BEAM we must start drawing with lines, then we can convert the lines
to the new sections, don’t start with area.
2 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
Preprocessor:
Choosing structural to
update all mechanical
and physical properties
such as Loads, stresses ..
etc.
3 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
In ANSYS 14.0, we choose any
of these two choices, But in the
versions such as 11 and below we
must choose (2D elastic 3)
4 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
In Ansys 14.0, we cannot add
constants such as (area, moment of
inertia, height .. etc.) in the current
Real Constant order, But we can do
that in ANSYS 11 and below, So
we have to make the constants
depending on the next SECTION
order which is more accurate.
5 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
e: means exponential
2e5: means 200000
PRXY : start from 0
and less than 1, here
take it 0
6 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
In the current problem we have two sections are same,
and third section is different.
Set ID=1 then choose Sub-type as in the problem, then
fill in the dimension below, then press Preview to see
the new figure in the screen with all properties then
press Apply, now repeat for the second section ... etc.
7 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
New method to enter keypoints :
Enter first one then Apply, then
enter second one then Apply,
then add third one as in fig. then
Apply, then add fourth one as in
fig. then OK.
8 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
Draw straight lines as in
the figure then OK.
9 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
After picking first line and Apply then
choose from this window number 1 ,
means we setup ID Section 1 for this
line, then Apply, again same procedure
for another two lines but changing to
No. 2 then No. 3
10 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
After picking first line and Apply then
write any number for element division,
and Apply then again repeat same
procedure for remaining two lines with
any No. of division according to the
length of lines.
11 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
12 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
Solution:
Applying constraints
on the LEFT and
RIGHT keypoints.
13 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
Better to change to
keypoints to setup
the suitable FORCE.
14 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
Enter the direction
and the magnitude of
the force, then OK.
15 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
Solve the problem
16 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
General PostProcessor:
Apply Def + Undeformed
17 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
Change to ON then OK.
18 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
We get like this.
19 | Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: haydar2200@yahoo.com
Von Mises Stress
Recommended