View
23
Download
2
Embed Size (px)
Citation preview
1
STH-03ZB User's Manual
STH-03ZB User's Manual
Ver. 1.02
Copyright@2011 Nietzsche Enterprise Co., Ltd. All rights reserved.
Nietzsche Enterprise reserves the right to make changes and improvements to its products
without notice.
Contact information: E-Mail: [email protected]; Website: www.nhr.com.tw
INDEX
1. STH-03ZB Manual ................................................................................................................2
2. What is in the box .................................................................................................................2
3. STH-03ZB Views ..................................................................................................................2
4. Installing Mounting for STH-03ZB.........................................................................................3
5. Installing and Replacing Batteries in STH-03ZB ...................................................................4
6. Setting Transmission Interval for STH-03ZB.........................................................................5
7. Adding STH-03ZB to Receiving Device ................................................................................6
8. Removing STH-03ZB from Receiving Device .......................................................................7
9. STH-03ZB LED Signal Status ...............................................................................................7
10. ZigBee Reset ........................................................................................................................8
11. Product Specifications...........................................................................................................8
2
STH-03ZB User's Manual
1. STH-03ZB Manual
Congratulations for choosing a world-class digital temperature and humidity sensor using
state-of-the-art ZigBee wireless transmission technology. This manual is designed to help set up
and get the most from the sensor in a few short minutes.
2. What is in the box
NHR STH-03ZB digital temperature
and humidity sensor
Mounting fixtures (mounting cradle,
2 wall plugs, 2 screws)
2 x AA batteries
If any of the above is missing, please contact your supplier.
3. STH-03ZB Views
The following is the front view of STH-03ZB The following is the base view of STH-03ZB
The following is the side view of STH-03ZB The following is the back view of STH-03ZB
Battery Compartment
Transmission Interval Setting Temperature & Humidity Sensor
Status LED
Link Switch
Product Serial Number &
Unique MAC Address
3
STH-03ZB User's Manual
4. Installing Mounting for STH-03ZB
You will need:
Mounting fixtures
Drill with 5mm (approx. 0.2 inches) drill bit size (if using wall plugs) or 3.5mm (approx. 0.14
inches) drill bit size (if not using wall plugs)
Size 1 Phillips screwdriver
4.1 Locate STH-03ZB with at least 15cm (approx. 6 inches) spacing on each side (except
mounting side).
4.2 If it is necessary to pre-drill mounting holes, use mounting cradle to align locations for the 2
holes, then use appropriate drill bit to drill the holes - 5mm (approx. 0.2 inches) if using wall
plugs or 3.5mm (approx. 0.14 inches) if not using wall plugs. Note: pay careful attention to
orientation of the mounting cradle.
4.3 If necessary, insert wall plugs into the 2 holes and use size 1 Phillips screwdriver for the 2
screws to secure the mounting cradle. Note: pay careful attention to orientation of the
mounting cradle.
4.4 Install and remove STH-03ZB using the following 2-step actions to ensure mounting has
been correctly and securely installed:
Install - Remove -
4.5 Initial hardware installation for STH-03ZB has been successfully completed.
1
2
1
2
Orientation UP Arrow
4
STH-03ZB User's Manual
5. Installing and Replacing Batteries in STH-03ZB
You will need:
2 x AA batteries
5.1. Open the battery compartment using the following two-step action:
5.2. If necessary, remove existing batteries.
5.3. Install 2 AA batteries into the battery compartment.
5.4. The status LED on STH-03ZB should start flashing to indicate its current state:
Green LED Status
1 flash per second (loop) Ready to connect to coordinator or router device
1 flash every 60 seconds (loop) Already connected to coordinator or router device and
functioning normally
Rapid flashing (continue) Already connected but unable find coordinator or
router device
5.5. Replace battery compartment by first slotting base into STH-03ZB then clicking close the
compartment.
5.6. New batteries have been successfully installed.
Recommendation: It is strongly recommended to install batteries into STH-03ZB just before
adding to coordinator or router device as this will greatly improve battery life. For proper
functioning of STH-03ZB and longer battery life, please install alkaline batteries from reputable
suppliers.
Low battery power is indicated by the red LED repeating the following sequence: 2 rapid flashes
and pause 5 seconds. Replace batteries immediately to ensure correct functioning of
STH-03ZB.
1
2
1
2
5
STH-03ZB User's Manual
6. Setting Transmission Interval for STH-03ZB
6.1 If necessary, remove STH-03ZB from mounting cradle (see "Installing Mounting for
STH-03ZB"""" section).
6.2 Using the following setting positions to set the appropriate transmission interval for
STH-03ZB:
Transmit Interval DIP Switch Setting Transmit Interval DIP Switch Setting
1 Second 1 Minute
5 Seconds 5 Minutes
10 Seconds 10 Minutes
15 Seconds 15 Minutes
20 Seconds 20 Minutes
25 Seconds 25 Minutes
30 Seconds 30 Minutes
35 Seconds 35 Minutes
40 Seconds 40 Minutes
45 Seconds 45 Minutes
50 Seconds 50 Minutes
55 Seconds 55 Minutes
60 Seconds 60 Minutes
65 Seconds 65 Minutes
70 Seconds 70 Minutes
75 Seconds
75 Minutes
6.3 Ensure STH-03ZB is connected to a coordinator device (see "Adding STH-03ZB to
Receiving Device"""" section).
6.4 Use QuickView Data PS software on PC with coordinator device to confirm STH-03ZB
transmissions are being received and the update interval has been set correctly.
6.5 Replace STH-03ZB into mounting cradle (see "Installing Mounting for STH-03ZB"""" section)
as required.
6.6 Transmission interval setting has been successfully configured.
6
STH-03ZB User's Manual
7. Adding STH-03ZB to Receiving Device
You will need:
Sharp pointed tool
Coordinator or router device (WZB-01USBPS or WZB-02485RPS or WZB-01USBPSR or
WZB-05ETPS)
7.1. Ensure coordinator or router device is powered on (see relevant device’s manual).
7.2. Ensure batteries have been installed in STH-03ZB (see "Installing and Replacing
Batteries in STH-03ZB" section).
7.3. Use the sharp pointed tool to apply 1 quick press to link switch on the coordinator or router
device, the blue ZigBee LED should flash 1 flash per 0.5 second and repeat the sequence,
detection can take up to 30 seconds.
7.4. If 30 seconds has passed and no device has been connected, the blue ZigBee LED on the
coordinator or router should return to one flash then pause for a second and repeat the
sequence.
7.5. When STH-03ZB has been connected, the blue ZigBee LED on the coordinator or router
device should flash, it should return to one flash then pause for a second and repeat the
sequence.
7.6. If STH-03ZB has been successfully connected, the green status LED should flash every 60
seconds to confirm successful addition.
If STH-03ZB’s status LED does not flash once every 60 seconds, then it has not been connected
successfully. Repeat above steps until STH-03ZB has been connected successfully. If
STH-03ZB has still not been connected successfully after a few attempts, check it is within the
operational distance of 50m (line of sight) from the coordinator or router device and away from
other 2.4GHz devices that might interfere with its operation.
If STH-03ZB had been successfully connected, but is showing unable to find coordinator or
router device (repeating sequence of 2 flashes and pause for 2 seconds), then check coordinator
and all router (where applicable) devices are correctly powered on. If coordinator and all router
(where applicable) devices are functioning correctly, STH-03ZB may be out of range from the
coordinator or router device, an additional router may need to be added to extend the range.
7
STH-03ZB User's Manual
8. Removing STH-03ZB from Receiving Device
You will need:
Sharp pointed tool
8.1. Ensure coordinator or router device is powered on (see relevant device’s manual).
8.2. Ensure STH-03ZB is powered on (see Installing and Replacing Batteries in STH-03ZB
section) and has already been connected to the coordinator or router device.
8.3. Use the sharp pointed tool to apply 2 quick presses to the link switch on the coordinator or
router device, the blue ZigBee LED should flash rapidly for up to 30 seconds or until removal
has been successful, removal need to take place within 30 seconds.
8.4. 3 quick presses to the link switch on STH-03ZB, the green status LED should flash rapidly
for up to 30 seconds or until removal has been successful.
8.5. If STH-03ZB has been successfully removed, coordinator or router device’s blue Zigbee
LED should flash once and pause for one second then repeat the sequence, STH-03ZB’s
green status LED should flash once per second.
Recommendation: It is strongly recommended to remove batteries immediately from STH-03ZB
once it has been removed successfully from the coordinator or router device as this will greatly
improve battery life.
9. STH-03ZB LED Signal Status
The table below shows the LED signal status for STH-03ZB:
STH-03ZB LED Status
Green LED:
1 flash per second (loop)
Ready to join – ready to be connected to
coordinator or router
Green LED:
1 flash every 60 seconds (loop)
Successfully Connected – connected and
functioning normally
Green LED:
Rapid flashing (continue)
Orphaned – connected but unable to find
coordinator or router
Green LED:
Rapid flashing up to 30 seconds
Removing – being removed from coordinator or
router
Green & Red LED:
ON for 3 seconds
ZigBee Reset – Zigbee linkage to all data
receivers being reset
Red LED:
1 flash every 60 seconds (loop)
Low Power – low battery power, replace
batteries immediately
8
STH-03ZB User's Manual
10. ZigBee Reset
In the case where the data receivers (coordinator or router devices) for the STH-03ZB are no
longer available or have been reset, to clear STH-03ZB ZigBee linkage to all data receivers,
apply 3-second press to the link switch, the green and red status LEDs should be ON for 3
seconds, then return to just the green status LED flashing once every 1 second.
STH-03ZB’s ZigBee linkage to all data receivers has been cleared.
Recommendation: It is strongly recommended to remove batteries immediately from STH-03ZB
once its linkage to data receivers has been removed successfully as this will greatly improve
battery life.
11. Product Specifications
Measurement Channel Built-in 1 temperature and humidity sensor
Wireless Protocol l Compliant IEEE 802.15.4, ZigBee2007/PRO
Operating Frequency 2.4GHz ISM Band
Transmission Range 50m (around 164 feet) Line of sight
RF Output Power 1mW/ 0dBm
Power Supply 3V 2 AA Alkaline battery
Operating Environment -10~ +55 ºC, 85%RH. Max.
Power Consumption TX:35mA Sleep:1.3uA
Measurement Accuracy Temperature +0.5 ºC/ Humidity +/-5%
Network Topology Star/ Tree/ Mesh
Transmitting protocol Modbus RTU
Addressing IEEE MAC 64bit
Transmit Interval 1 second to 75 minutes setting by DIP Switch
Battery Life 1 year based on sending data per 5 minutes
Coordinator WZB-01USBPS / WZB-05ETPS Peripherals
Router WZB-01USBPSR / WZB-02485RPS
Dimensions 92(L) x 50(W) x 23(H) mm
Weight 86g
OS Windows 95/ 98/ NT/ 2000/ XP/ Vista/ Win7
Certifications CE/ FCC