Expect Brilliant Results

Magnetic Field Effective Driven catalysis1

1 - Catalysis is the increase in the rate of a chemical reaction due to the participation of an additional substance called a catalyst. With a catalyst, reactions occur faster and with less energy, because catalysts are not consumed, they are recycled.

Patent, #8,714,967, issued May 6, 2014 by USPTO. High Flow-Rate System. MFED system has no power requirements for operations. MFED system has no moving parts. MFED system does not use any chemicals and has no harmful by-

products. More energy efficient because of superior flocculation2.

2 – Flocculation: The separation of a solution, most commonly, the removal of a sediment from a fluid.

Changes the Geometrical Shape of Molecular Structures of fluids and materials.

Based on Magnetic Hydrodynamic Principles that Michael Faraday experimented with in 1839.

MFED breaks down materials at a molecular level. Molecular Sciences technology. Catalysis process breaks apart carbon/carbon bonds. Based on MHD magnetic hydrodynamics. Fuel Efficiency increases have been proven up to 14%

Unique magnetic flux (“UMF”) is applied to hydrocarbon-based fuel pre-consumption.

UMF provides inter-molecular excitation promoting molecular spin and vibration of the hydrocarbon molecule.

UMF creates intra-molecular stresses that weaken covalent C-H and C-C bonds in alkane fuels and enhances reaction rate similar to a catalytic effect.

Increased collision frequency promotes the combustion reaction and pushes it closer to perfect conditions.

In essence, the MFED® enhances the ability of fuel to react with combustion air to improve combustion kinetics to enable the release of more heat from a given amount of fuel.

Water Treatment Fuel Enhancement Oil Well Pipeline

Water TreatmentBenefits:

Recycling Vs. Disposal. Operating Cost Reduction. Production of recycled water for the following approved beneficial re-use:

o Well stimulation fluidso Spray irrigationo Sub-surface irrigation

Improves water purity to a quality standard suitable for land irrigation as well as fracking operations.

Byproduct created during the process is non-toxic and can be used to produce fertilizer.

AnalogyWhen experimenting with two magnets. Point the North pole of one magnet toward the South pole of the other magnet. They will attract. Opposite poles will repel.

In basic terms, if you run foul water through two opposing magnets, the molecules in the water will explode and separate. Thus, the clean water goes to storage tanks and the solids, composed of mineral oxides, flow to the disposal storage tanks.

System has produced stunning

results on simulated

fouled water.

The following results were obtained in 10 seconds

of processing

time:

Physically alters the inter & intra‐molecular physical properties of gaseous and liquid fuels

Enables gaseous and liquid fuels to produce more heat upon combustion; reduced fuel usage for the same process output

Uses no chemicals or other additives

Designed for in‐line flow, high or low pressure fuel lines to industrial and power sector combustion chambers

The MFED® Effect:

• MFED® activates fuel through excitation and, in case of liquid fuels, viscosity reduction and optimized atomization

• MFED® activated fuels combine with air more effectively

• Better air/fuel combination as a result of geometrical shape change and more complete combustion with less air

• Lower air requirement drives improved thermal efficiency without increasing emissions

Burners experience INCREASED

fuel efficiency with MFED®

The ProblemAs oil enters the pipeline, it encounters various problems such as cooling of the fluid, thus increasing the viscosity and slowing the flow, and turbulent flow. With longer distances and colder environments, the problem becomes exacerbated.

Less buildup of wax and/or solids. Reducing the crude viscosity for improved faster flow. Units are all 150 psi flange rated and have been tested and

certified with the paperwork for hydro testing and welding procedures.

Lowering the viscosity of crude oil is important in the oil industry. It is especially important for transporting oil via pipelines. As more and more heavy crude oil is produced, a reliable technology to lower crude oil’s viscosity becomes urgent.

MFED’s application of a suitable magnetic field pulse can significantly reduce the viscosity of crude oil for several hours. Whether for paraffin-base crude oil or for asphalt-base crude oil or mixed-base crude oil.

This viscosity reduction method does not change the temperature of the crude oil; instead, it temporarily aggregates paraffin particles or asphaltene particles inside the crude oil into large ones. The particle aggregation changes the rheological property of the crude oil and leads to the viscosity reduction. While this viscosity reduction is not permanent, it lasts for several hours and is repeatable.

One well-known approach to improving the flow is to use a polymer to improve the flow characteristics. However, these DRA polymers are very expensive.

The MFED will accomplish the increased flow of the crude product by reducing the molecular weight of the flowing crude product without the introduction of chemicals or polymers, thus being safer for personnel and operations.

Reduces the viscosity of the crude for improved, faster flow. Requires no chemicals or additives. Eliminates the need for pigging operations.More up-time of the pipeline infrastructure. Faster Transporting of the product to final destination.MFED system is installed directly in-line with the pipeline.

Larry White281.794.7969

larry@fidelisenergypartnersllc.com

For additional information, copies of White Papers, test results, and/or demonstrations, please contact Larry White.