Upload
icpdas
View
115
Download
3
Embed Size (px)
Citation preview
ICP DAS Co., Ltd.
PLASTIC INJECTION MACHINE MONITORING SYSTEM
ICP DAS Co., LTD. Joyce Yeh Tel: +886-3-5973366 ext: 3307 Email: [email protected]
ICP DAS Co., Ltd.
Outlines
¢ Background ¢ Requirement ¢ The fact and difficulty ¢ How to obtain the machine data? ¢ System Architecture ¢ Solutions ¢ Benefits ¢ Why ICP DAS?
ICP DAS Co., Ltd.
Background
• Location: Indonesia
• Plastic products manufacturer for IKEA
• More than 100sets of plastic injection machines
• Operators may steal the products
• 2015 electricity charge is increased up to 40%
ICP DAS Co., Ltd.
Requirement
• Machine power consumption monitoring • Machine operation monitoring • Production status monitoring
• Remote monitoring
• Reports
• Alarm
ICP DAS Co., Ltd.
The fact and difficulty
• PLC+HMI for single machine control without networking function
• Machine maker doesn’t want to modify PLC program and provide source code
ICP DAS Co., Ltd.
How to obtain the machine data?
1. Read register mapping of PLC I/O by RS-232 à Not possible due to poor support from PLC
programmer
2. Get data from physical I/O points à M-7000 DI module to read DI status according
to machine wiring guide
ICP DAS Co., Ltd.
System Architecture
ICP DAS Co., Ltd.
Injection Molding Machine Monitoring
• TouchPAD (TPD-433) will read the power information, temperature, door lock status, and count the mold opening & closing times.
• By Ethernet, RS-485 or ZigBee, TouchPAD can easily integrate with SCADA system.
ICP DAS Co., Ltd.
Introduction of Operation & Management Interfaces
Operation Interface(TPD) • On-site Operation( Machine) • Machine Maintenance • Mold Replacement • Event Logger
Operation Interface(SCADA) • Central Management(PC) • Machine Status Logger • Power Status Logger
ICP DAS Co., Ltd.
Operation Interface – TPD at Machine Side
TPD-433F TPD-433F is placed on the machine. Machine status is sent back to the control center in real time.
REPAIR
RUN
MOLD
Buttons on Main Page
ICP DAS Co., Ltd.
Operation Interface – Repair
When performing repair/maintenance, press the red “Repair” button to start recording the repair time.
Password or employee ID (or both) is required to process the operation.
Comments of repair/maintenance can be inputted by English or digits (max. 15 characters)
ICP DAS Co., Ltd.
Operation Interface – Run
After the mold replacement or maintenance of the device is completed, press green “Run” button to start the machine for calculation of production quantity & record of machine status.
ICP DAS Co., Ltd.
Operation Interface – Mold Replacement
When performing mold replacement, press blue “Mold” Button to start recording the time spent on replacing of the mold
Password or employee ID control.
Input the mold code for record
Input the quantity of defective products produced by current mold after the end of production.
ICP DAS Co., Ltd.
Management Interface -SCADA at PC Side
Display status of all machines
Connection status between Operation interface(machine)& Management Interface(PC)
Machine abnormal alarm
Daily/Monthly power consumption (in kWh)
ICP DAS Co., Ltd.
Injection Machine Monitoring & Status Overview
Automatically detect and display current Machine Status
ICP DAS Co., Ltd.
Single Injection Machine Monitoring Information
Production status • Cycle Time(time per piece) • Time to complete production
Production Analysis • Production Quantity • Time Spent • Defective No. & Rate
Maintenance Record • Time • Code (Eng. or No.)
Machine Status • Mold open & close • Engine Operation • Heating for Injection
ICP DAS Co., Ltd.
Power Consumption Overview
User-Defined Electricity Rates • Rates of Time Zone 1 (22:00~18:00) • Rates of Time Zone 2 (18:00~22:00)
Daily (updated daily) • Price of Time Zone 1 • Price of Time Zone 2 • Total daily cost
Total Electricity Cost Calculator Monthly (updated monthly) Price of Time Zone 1 • Price of Time Zone 2 • Total Monthly cost
ICP DAS Co., Ltd.
Power Consumption Monitoring of Single Machine
Electricity Cost log • Daily • Monthly
Electricity Cost Display • Daily (updated daily) • Monthly (updated monthly)
Power Consumption Information 1.V 4.I 2.kW 5.kVA 3.kWh 6.kVAh
Power Consumption Trend Chart 1.V 4.I 2.kW 5.kVA 3.kWh 6.kVAh
ICP DAS Co., Ltd.
Solutions
¢ M-7055D: � Machine Status (DI: ON/OFF) � Motor Status (DI: ON/OFF) � Safety Door Status (DI: ON/OFF) � Safety Door Limit Switch (DO: ON/OFF) � Mold Open & Close Status (DI Counter, DI ON/OFF) � Injection Preheating Status (DI Counter, DI ON/OFF)
¢ TPD-433F: � Read and display module information and convenient for operation at
local site � Repair Mode/Mold Mode/Run Mode/Defective Quantity
ICP DAS Co., Ltd.
Solutions
¢ LC-101 � Control safety door Open/ Close
¢ M-7011D � Preheating temperature
¢ PM-3133 � Machine power consumption
¢ WF-2570/2571 l Ethernet to Wi-Fi Bridge that creates a connection between
TPD-433F and control center (InduSoft) ¢ InduSoft
ICP DAS Co., Ltd.
Benefits
¢ Enable traditional machines networking capability
¢ Convert different PLC protocols to Modbus
¢ Restriction free by machine maker
¢ Integrate all real time machine operation and production data to control center
¢ Easy to install and deploy
ICP DAS Co., Ltd.
¢ InduSoft: real time data display ¢ Report: retrieve data from BD for customization
Benefits
ICP DAS Co., Ltd.
Why ICP DAS?
¢ High CP ratio
¢ Data acquisition and communication expert
¢ Field and integration experience
¢ Good service: system analysis, system planning, system design