Upload
bryan-herity
View
535
Download
2
Embed Size (px)
Citation preview
HAVELLS USABryan Herity
2
Mission
One of Europe’s most respected commercial and architectural lighting brands Renowned for its strong design ethos, high technical performance and aesthetic form
Wide range of contemporary designed fixtures Intended for lighting medium to large projects (shops, offices, hotels and restaurants)
Brand Portfolio
Strong dominant brand in the India home market
A full-spectrum provider of professional electrical solutions worldwide
An Expanding Global Leader
U$1.4 Billion +One of the world’s largest lighting and electrical product companies
Global HQ:Noida, India
InnovativeHighest quality standardsStrong distribution strategyStrong brands
ISO certified & EU-Eco Audit
62%
27%8%
3%
0% 10% 20% 30% 40% 50% 60% 70%
Wholesale
Retail
OEM
Enduser
HAVELLS World Wide
Full Line Lamp Manufacturer
Lamps
Full Line• T8 Electronic Fluorescent• T5 Electronic Fluorescent
• Quick connect• Leads
Limited Line• T12 Electronic Fluorescent• Electronic CFL
Full line magnetic• Metal Halide• HPS
Havells Brand
Ballasts
Full Line Fixture Manufacturer
Fixtures
10
One-stop shoppingInnovative range of lamps Broad selection of fixturesEfficient ballast
Professional Lighting Solutions
11
Residential Industrial Outdoor
Retail & Display Commercial Hotels & Leisure
Major Target Segments
VAPORTITE FIXTURE LAUNCH Fluorescent T5 &T8 FIXTURES
FEATURES BENEFITS
Durable fiberglass housing Adaptable to any adverse conditions
Poured in place gasketing Allows enclosure to be sealed from harsh environments
Injection molded diffuser Shatter resistant lens reducing breakage
Corrosive resistant latches Standard on all units
Stainless steel mounting clips For easy installation
Energy Efficient Available with T5 or T8 lamp options
Lightweight Easy to mount
Easy ballast removal Removable gear tray for access
Rubber end plug For utilization of standard die cast liquid or water tight fittings
IP67 Rated Dust tight rated and temporary immersion in water
NSF Splash Zone Certification Approved for washdown environments
Vaportite (VP Series) - Fluorescent T5 & T8
ISO 9001-2000 & ISO 14001
Fixture Plant in Costa Rica
Specification Sheets
Stainless Steel mounting clips
Rubber End Plug
Removable Gear tray for ballast access
Injection molded diffuser
Polycarbonate Latch to secure lens
Exploded View
Latching Options: Clear Polycarbonate or Stainless Steel. Both options can easily be made tamper resistant.
Stainless Steel Latches are securely held in place to prevent loss during maintenance.
Simple Mounting SystemReduces installation labor
costsNo holes drilled through the
housingVariable mounting centersUL rated
BailsOptional bail provides convenient means of suspending the fixture
Stainless Steel Mounting Clips
Accessories
Insert one side of the Vaportite housing into the mounting brackets.
Securely attach mounting brackets (2) mounting surface. The Vaportite enclosure will engage the mounting brackets at any point along it’s length, except for where there are latches. It is recommended that the dimension between brackets equal about 70-80% of the enclosure’s length.
Installation
T5 High Output Fluorescent LampT8 & T8HO Fluorescent Lamp3 Lengths (2’, 4’ and 8’)2, 3, 4, 6 lamp x 32 T8 watt or 54 T5
wattPendant or surface mountedSupplied with SLI ballastUniversal voltage (120 volt to 277
volt) standard
Vaportite T5 & T8 Fixture
Protection Against Solid Objects Protection Against Liquids
First No. Definition Second No. Definition
0 No protection 0 No protection
1 Protected against solids objects over 50mm (e.g. accidental touch by hands.)
1 Protected against vertically falling drops of water
2 Protected against solids objects over 12mm (e.g. fingers)
2 Protected against direct sprays up to 15 from the vertical
3 Protected against solids over 2.5mm (e.g. tools and wires)
3 Protected against direct sprays up to 60 from the vertical
4 Protected against solids objects over 1mm (e.g. tools, wires and small wires
4 Protected against sprays form all directions – limited ingress permitted
5 Protected against dust – limited ingress (no harmful deposit)
5 Protected against low pressure jets if water from all directions – limited ingress permitted
6 Totally protected against dust (dust tight) 6 Protected against strong jets of water (e.g. for use on shipdecks – limited ingress permitted
7 Protected against the effects of temporary immersion between 15cm and 1 m. Duration of test 30 minutes
8 Protected against long periods of immersion under pressure.
IP Rating System (IP67)
NSF Certification Description of Location/ Use and Commentary Typical Lighting Applications
Non-Food Zone Areas where direct contact with food products during normal operations would not be expected. Equipment is located outside the normal washdown area. There is a concern that the fixture will add contamination to the protected space or food product (i.e. Cleanability - will the finish withstand cleaning, chipping paint, deteriorating paints or finishes, lens impact resistance, lamp glass breakage, etc.
Kitchens; food storage dry process areas; damp process areas – no drip possibility
Splash Zone Areas where direct contact with food products during normal operations would not be expected; however , the fixture may be situated such that liquids used in the process or cleaning procedures, may splash, spill or otherwise soil – either intentionally or inadvertently – the surface on the fixture. There then is the potential for dripping or draining onto other surfaces or even the process. Since these fixtures are often used in washdown areas, a Wet Location listing is not sufficient. Fixtures must be tested to withstand high-pressure hose washdown. The concerns of Non-Food Zone also apply.
Wet or damp process areas; high pressure purging or decontamination used in the process; area hose washdown
Food Zone Areas where direct contact with food products is normally expected and surfaces from which the food may drip, drain, or splash back onto surfaces normally in contact with food. Equipment other than lighting fixtures typically require this certification (i.e. work tables, cutting boards, other direct contact equipment.
Category not typically used for lighting
NFS Certification (Splash Zone Rated)
CENIT FIXTURE LAUNCH Fluorescent T5 &T8 High Bay Lighting
• Very low profile • Only 2.4’ deep/ Lightweight for easy installation.
• Mounting Options • Can be surface or pendant mounted.
• Pre-wired for multi level switching • Provides for 2 levels of lighting
• Anticorrosive treated steel housing finished with electrostatic powder coating after fabrication
• No sharp edges with anti rust capabilities
• Anodized aluminum reflector designed specifically for each available lamp configuration
• Highly reflective surface yielding very high fixture efficiencies
• Side mounted ballasts • Allows ballast to maintain a lower ambient temperature
• Havells manufacturing facility builds every fixture • Complete control and adaptability over all aspects of manufacturing
• Quality Control • Each fixture is lamped and energized in factory
• Energy efficient • Reduces operation costs with a superior quality of light
• Availability • Most common configurations are in stock
• Several Options • Available with cable mounting kits, wireguards, 6 ft. cords, emergency ballast, door frames with clear lens, and occupancy sensors
CENIT Fluorescent T5 & T8 High Bay Lighting
Specification Sheet
Ballast Access
Access to ballast removing side reflector sections
• Overheat test• Ballast temperature remained below 90°C limit• Heat emitted by lamps doesn’t rise towards ballasts
10 20 30 40 50 60 70 80 90 100 110
Component Temp on Cenit 6x54w
4x54w Ballast
2x54w Ballast
Lamp (center)
Ambient Temp C/F°
120/248
40/104
100/212
20/68
40/104
60/140
80/176
100/212
120/248
80/176
60/140
Co
mp
on
ent
Tem
p
C
/F°
Not recommended for applications with ambient temperature above 35°C (95°F) due to lamp output reduction
Thermal Impact of Ballast Location
• Can be surface or pendant mounted• Hanging kit must be attached to at least two points on the ceiling
Installation
• UL required labels and hanging cable kit installation
Stop sleeve on all four hanging kit cables. Must pass through this hole and slide inward.
Surface mount holes.
Labels on Fixture Body & Cable Kit
Installation Instructions
• 3D model view from below - guard attached
Wideguard (Currently being developed)
T5 High Output Fluorescent LampT8 Fluorescent Lamp3 Fixture sizes
14” wide25” wide33” wide
2, 3, 4, 6, 8 x 32W or 54WPendant or surfaceSupplied with Havells USA ballast
4 lamps 1 ballast6 lamps 2 ballasts8 lamps 2 ballasts
Universal voltage (standard)
CENIT Fluorescent T5 & T8 High Bay
• Example of incorrect application of high bay fixture for low bay site
49%
34%
15%
2%
Reflector Performance
AdvantagesHigh efficiency (energy savings and photometricaly efficient).High CRI, instant restart, and double circuit for energy saving.Less weight on structures, less heat emission.Return on Investment (ROI) advantage.
Top view of warehouse. Illumination simulation by Marketing’s Projects Dept.
6 Cenit 4x54w T5HO
5 MH 400w
5 Cenit 6x54w T5HO
1,182 watts/21 FC avg.
2,485 watts/19FC avg.
1,550 watts/30FC avg.
CENIT T5 High Bay Retrofit
5 10 15 20
Life in thousands of hours
10
20
30
0
Thou
sand
s of
em
itted
lum
ens
Cenit 6x54W T5HO
Metal Halide 400W
Comparison of luminous maintenance & energy savings for a 6 Lamp Fixture
310W
475W
Replacement Costs
(Replace 1–400W MH HID with 1-6 lamp T5HO High Bay fixture)
$185 installed & lamped
165 watts/fixture of energy savings
Over 50% increase in lighting levels
Return on Investment
(ROI) = 20 months
CENIT T5 High Bay Retrofit