Color IR Bullet CameraUser Manual

Model : AA-4547P-FSR3Model : AA-6047P-FSR3

CAUTION : TO REDUCE THE RISK OF

ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

02

This lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intend to alert the user to the presence of important operating and maintenance instruction in the literature accompanying the product.

FCC WARNING : This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the user manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN

03

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expenses.

A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

Holes in meta, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushing.

WARNING: Do not install this equipment in a confined space such as a bookcase or similar unit.

WARNING: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

WARNING: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

WARNING: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should confirm to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

To disconnect power from the mains, pull out the mains cord plug. While installing the product, ensure that the plug is easily accessible.

04

Caution: The apparatus should not be exposed to water and no objects filled with liquids, such as vases, should be placed on the apparatus.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop from where you purchased the product.

Important Safety Instructions

1. Read this instructions.-All these safety and user instructions should be read before the product is operated.

2. Keep these instructions:- The safety, operating and user instructions should be retained for future references.

3. Read all warnings :- All warnings on the product and in the operating instructions should be adhered to.

4. Follow all instructions:- All operating and user instructions should be followed.

5. Do not use this apparatus near water :- e.g near swimming pool ,Bathroom, wet walls.

6. Clean Only with dry cloth:- Unplug the power supply and then clean with dry cloth.

7. Do not block any ventilation openings, install in accordance with the mfg instructions:- Kindly provide some air ventilation in any form. The opening should never be blocked by placing the product on a bed, sofa, fug or other similar surface.

8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus that produce heat.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the pint where they exit from the apparatus.

10.Only use attachments/accessories specified by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used use caution when moving the cart/apparatus combination to avoid injury from tip over.

12.Unplug this apparatus during lighting storms or when unused for long periods of time.

13.Refer all servicing to qualified service personal. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged.

05

Safety Precautions

Do not attempt to disassemble the camera.

To Prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service personnel for servicing.

Do not use strong solvents or detergents.

Use a dry cloth to the camera when it is dirty. If it is hard to remove the dirt on the camera, Use a mild detergent and wipe it gently.

Before operating, please check proper temperature, humidity and power source ratings.

Use the camera under conditions where temperature is between -10°C ~+50°C.

Do not expose the camera in such conditions as shown below.

User in a room or area filled with cigarettes smoke, dust or gas.

Avoid the camera with direct sunlight

Do not aim the camera at bright objects. Never face it with direct sunlight or other extremely bright objects.

Otherwise blooming or smear may be caused.

Handle the camera with care

Do not abuse the camera .Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage.

Do not expose the camera to rain or moisture

This product is designed for indoor use or location where it is protected from rain and moisture.

06

Contents

Cautions for Safe Operation ........................................................ 07

Box contains ............................................................................... 08

Construction ............................................................................... 09

Installation .................................................................................. 11

Troubleshooting .......................................................................... 13

Specification ............................................................................... 14

07

Cautions for Safe Operation

Power Supply

This camera must always be operated a DC 12V only.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautious not to get combustible or metallic material inside the body. If used with foreign Matter inside, the camera is liable to fail or to get a cause of fire or electric shock.

Operating and storage location

Avoid viewing a very bright object during an extended period. Avoid operating or storing the unit in the following locations.

Extremely hot or cold places( -10ºC ~+50°C We recommended to use unit in between 0ºC ~+45°C)

Damp or dust place

Places exposed to rain

Places subject to strong vibration

Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.

08

Box contains

2

Camera

Cable

DC Power Plug

Video BNC Plug

Screws3

09

Construction

Front View

Sun Shield

10

Lens

Camera Body

IR Sensor

IR

Construction

11

Camera body

Up & DownControl Screw

Left & RightControl

Sun Shield

Camera Bracket

Side View

Installation

1) Locate Installation Area. Select area where it would hold the camera for long time.

2) 3-Axis Bracket on the wall or ceiling with "L" Wrench and screw given and select the area you would like to monitor.

3) Connect Power DC12V and Video Or in to Video Input of DVR.

4) Using a screw driver open or change the camera Mounting & Bracket for suitable Position.

5) Always install the camera on Right Position with Wall or Ceiling Mount.

12

3.

Up & DownControl

Left & RightControl

2.

Installation

13

Cable

Video

Power

Troubleshooting

lIf you are not able to view anything from the screen

- Check power, video, strength of signal. Check monitor input/output. Check camera connection number with monitor.

lFor Fuzzy Screen.

- Check camera lens for dust or dirt. If so wipe them off with dry towel or brush. - Check cover to see if it's clean. If not so then wipe them off with dry towel or brush.- Check for direct sunlight exposure towards camera. - Check and see if protection film from camera cover is removed. - Check for camera focus.

lFor Dark Screen

- Check for Monitor Brightness. Unbalanced Black & White on the Monitor. - Check Monitor -Adjust the cameras position or angle of lens.

lWhen screen is not clear with IR LED functioning

- Check glass cover for dust : If there is dust clean them with dry towel or brush

If problem still remains please contact our Technical Support Department.

14

Model

Image Sensor Sony 1/3” Super HAD CCD II Proprietary Image Sensor

Picture elements(Effective Pixels) PAL -500(H) * 582(V) PAL -752(H) * 582(V)NTSC - 510(H) * 494(V) NTSC - 768(H) * 494(V)

Scanning System 2:1 Interlace

Scanning Frequency PAL –H: 15.625 KHz V:50HzNTSC – H:15.734Khz V:60Hz

Horizontal Resolution 450 TVL 600 TVL

S/N Ratio >48 db >65 db

Shutter Speed 1/50(60) -1/20000s 1/50(60) -1/1000000s

Back Light Compensation(BLC) Auto

Auto Gain Control (AGC) Auto

White Balance ATW

Min. Illumination 0.01Lux @ Day 0.05Lux @ Day0 Lux @Night with IR Led ON 0 Lux @Night with IR Led

ON, IR Cut Filter

IR LED 48 Pcs

IR Effect Distance 35 Mtr approx

Focal Length 8 mm IR Enable Lens

AA-4547P-FSR4 AA-6047P-FSR4

Specification

15

Specification

Aperture f/1.2

Input voltage 12 V DC ± 10%

Video Output Level 1V p-p,75Ù BNC connectors

Power Consumption <450mA/ 12V DC @ Night Time with IR LED ON

Operating Temperature -10º to ~ + 50ºC

Operating Humidity Up to 90%

Dimension 280mm (L) x 92(W)mm x 175mm(H)

Enclosure Metal Bullet

IP Protection IP66

Weight 640 g (W/O Box)

16 www.avtrontech.com