Copyright 2013 Foundation Armor

Copyright 2013 Foundation Armor

Concrete Densifier

The Armor L3000 Concrete Sealer by Foundation Armor TM is the most advanced concrete densifier on the market. Aside from increasing the density of the concrete by up to 45%, it is guaranteed to waterproof and protect the concrete for a lifetime.

The Armor L3000 chemically reacts below the surface and does not change the color or appearance of the concrete. The concrete will look exactly like it did before being sealed. If the applicator decides to polish the concrete floor after applying the densifier, the Armor L3000 will help achieve the desired level of shine better, and faster than other densifiers on the market.

The Armor L3000 is easy to apply and the benefits are guaranteed.

Copyright 2013 Foundation Armor

Armor L3000 Concrete SealerARMOR L3000 SEALER STOPS: Water and vapor migration up to

100psi Moisture vapor transmission up to .015

WVT Alkali attack and efflorescence attack

ARMOR L3000 SEALER REDUCES: Transmission of hazardous gases,

including Radon The absorption of chemicals, chlorides,

solvents, fats and oils Internal chlorides by up to 50%-90%

ARMOR L3000 SEALER PREVENTS: The growth of mold, mildew, bacteria,

lichen, and moss Flaking, cracking, scaling and spalling

caused during freeze-thaw cycles Surface deterioration and discoloration

ARMOR L3000 SEALER INCREASES: •Overall strength, hardness, and density by up to 45% •Bond strength of epoxies, paints, and stains by up to 20%

ARMOR L3000 SEALER : NEVER peel, flake, or fade NEVER stain from exposure to UV rays NEVER leave behind a slippery surface coating NEVER have to be re-applied or maintained

Copyright 2013 Foundation Armor

How It Works

Water plus cement produces Calcium Silicate Hydrate (C-S-H) in a process known as Hydration. C-S-H is the binding system for concrete. Combined with the aggregate, C-S-H gives concrete its hardness and strength.

A reactive byproduct of the Hydration process is Calcium Hydroxide. When a Foundation Armor concrete sealer is applied to concrete, it reacts with the existing Calcium Hydroxide to produce additional C-S-H. This additional C-S-H is what provides the increased hardness and densification by up to 45%, and water resistance up to 100 PSI.

The Armor L3000 concrete sealer has the highest percentage of reactive material, and is optimized to make the silicate available more quickly for more rapid C-S-H formation.

Copyright 2013 Foundation Armor

Armor L3000 TM

The Armor L3000 TM is a permanent sealer that penetrates up to 4” into the substrate.

Armor L3000 TM – Where To UseThe Armor L3000 TM concrete sealer can be used on:Interior and exterior concrete, above and below grade.Vertical and horizontal uncoated concrete surfaces.Poured concrete, concrete bricks, concrete blocks, concrete slabs, concrete pavers, and stamped concrete.New and old concrete.Concrete with water, moisture, vapor, and radon permeability issues.

Armor L3000 TM – PreparationNew concrete must cure for a minimum of 28 days.Concrete must be free of paints, stains, oils, chemicals, sealers, and dyes.Remove any efflorescence, mold, or mildew prior to application.Surface can be swept or power washed prior to application.

Armor L3000 TM – ApplicationDilute Armor L3000 TM sealer with 1 part warm to hot water.Using a garden sprayer, saturate the surface of concrete.Roll out any puddles with a brush or roller, or wipe up an excess materials with a clean cloth.Use product when temperature is between 50-900F (10-320C).

Armor L3000 TM Dry TimeLet dry 6 hours.

Armor L3000 TM CoverageOne gallon of the Armor L3000 TM is diluted with 1 part warm water and covers up to 900 square feet. For old or porous concrete, or for applications that require a third coat, expect one gallon to cover up to 700 square feet.

Retail: $149.95/Gallon

Copyright 2013 Foundation Armor

Foundation Armor

TM

We hope you have enjoyed the presentation. Please visit FoundationArmor.com for access to our brochures and special programs.

Foundation Armor866-306-0246FoundationArmor.com