ESD PRODUCTS DISTRIBUTED BY …

ARGUS SELF CONTAINED HYDRAULIC ESD SYSTEM

ADDED VALUE:

DYNA-FLO IS THE EXCLUSIVE DISTRIBUTOR FOR THE ARGUS HYDRAULIC ESD SYSTEMS IN CANADA. AS A FULL SERVICE AUTOMATION HOUSE, WE HAVE THE EXPERTISE TO PROVIDE THE RIGHT PRODUCTS TO SUIT YOUR APPLICATION.

DYNA-FLO WILL SIZE & PROVIDE THE VALVE, ACTUATOR, MOUNTING HARDWARE, & HYDRAULIC SYSTEM. WE MOUNT AND TEST THE SYSTEM, SO THAT YOU ARE CONFIDENT THAT THE SYSTEM IS READY TO GO WHEN YOU RECEIVE IT.

HIGH & LOW PRESSURE* SYSTEMS AVAILABLE.

(1750 PSI OR 100 PSI OUTPUT)

PUMP MANIFOLD WITH 2 LITRE RESEVOIR.

LOW TEMP RATED FOR REMOTE OUTDOOR OPERATION.

TROUBLE SHOOTING & MAINTENACE IS MUCH EASIER THAN TRADITIONAL

SYSTEMS.`

SUPPLIED WITH CUSTOMERS CHOICE** OF BALL VALVE.

SHUTDOWN OPTIONS ARE:1) ARGUS HYDRAULIC PRESSURE PILOT.

2) ELECTRIC SOLENOIDS. ( 12 OR 24 VDC VOLTAGE OPTIONS)

3) PNEUMATIC RELAYS.

4) COMBINATIONS OF ALL OF THE ABOVE.

DESCRIPTION:

* LOW PRESSURE SYSTEMS ARE LIMITED BY FLUID CONSUMPTION. PLEASE CONSULT DYNA-FLO FOR FURTHER INFO.

** WE REQUIRE DATA TO SIZE ACTUATOR

HIGH PRESSURE PUMP WITH INSTRUMENTATION:

LOW PRESSURE PUMP:

HYDRAULIC CONTROL SIGNAL SCHEMATIC:

LATCHING VALVE EXHAUST

PILOT EXHAUST FLUID FILL PORT

VENT CAP

AUXILIARY EXHAUST

PUMP MANIFOLD BOTTOM VIEW INSIDE HYDRAULIC RESEVOIR

FILTER FOR PUMP SUCTION

PRESSURE RELIEF VALVE

MANUAL PRESSURE DRAIN VALVE

LATCH VALVE:

ARGUS DESIGNED A TIME-OUT TO ENSURE LINE PRESSURE COMES INTO RANGE OF THE SET POINTS OF THE PILOT, WHEN PUMPING OPEN THE ACTUATOR & VALVE.(APPROX 14 MINUTES) SO THAT YOU CANNOT WALK AWAY WITHOUT ESD PROTECTION.

WHEN USING A SOLENOID VALVE, THIS WILL LATCH AS SOON AS THE SOLENOID VALVE IS ENERGIZED

MANUAL SHUT-DOWN:

UNLIKE OTHER SYSTEMS, ARGUS HAS MADE MANUAL SHUT-DOWN EASY. OTHER SYSTEMS MAKE YOU FORCE THE LATCH VALVE CLOSED.

THE MANUAL SHUT-DOWN HANDLE THAT ARGUS DESIGNED, ELIMINATES FORCING THE FLUID THE WRONG WASY PAST THE SEALS OF THE LATCH VALVE, WHICH CAN CAUSE POSSIBLE DAMAGE OR LEAKS.

ARGUS HYDRAULIC PILOT: 2” MNPT CONNECTION. ASME B31.3 COMPLIANT. NACE MR-01-75 COMPLIANT. PRESSURE ASSISTED POPPET,

ELIMINATES DEADBAND. TEMPERATURE RATING -46⁰ C TO

+121⁰ C (-50⁰ F TO + 250⁰ F. ACCURATE RESPONSE TO SET

POINTS RANGING FROM MIN. 20 PSI TO A MAX. OF 5000 PSI.

TWO SPRING CONSTRUCTION ACHEIVES WIDE RANGE OF SET POINTS.

ADJUSTABLE SET POINTS, REPLACEABLE SPRINGS & MAINTENANCE CAN BE DONE IN THE FIELD.

ARGUS PILOT & ISOLATION VALVE

LOW PRESSURE SET POINT ADJUSTMENT

HIGH PRESSURE SET POINT ADJUSTMENT

POPPET ASSEMBLY

PIPELINE PRESSURE INDICATOR

ISOLATION VALVE

CALIBRATION PORT

ARGUS ISOLATION VALVE: 2” FNPT X 2” MNPT. (FLANGED UNIT SHOWN) A30LF2 FORGED STEEL BODY FOR

LOW TEMP SERVICE. (FULL SST AVAILABLE)

4000# W.O.G. RATED @ +100⁰ F. NACE MR-01-75 COMPLIANT. 316SST BALL, 17-4PH SST STEM. ALWAYS COMES W/ PRESSURE

GAUGE AND NEEDLE VALVE FOR FIELD SERVICING OF PILOT.

ARGUS HIGH PRESSURE SOLENOID

¼” NPT PORTS. 2-WAY NORMALLY CLOSED / OPEN

OPERATION. 12 OR 24VDC VOLTAGE. LOW WATTAGE DRAW FOR REMOTE

LOCATION WITH SOLAR POWER. MAX OPERATING PRESSURE 2000 PSI. MANUAL RE-SET AFTER EVERY

SHUTDOWN.

RADIUS HIGH PRESSURE HYDRAULIC ACTUATORS SCOTCH YOKE DRIVE MECHANISM. 4000+ IN/LBS OF SPRING END TORQUE. SINGLE ACTING, SPRING RETURN OPERATION. 1750 PSI HIGH PRESSURE SUPPLY. LOW TEMP RATED. POSITION INDICATOR INCLUDED. ISO 5211 MOUNTING COMPLIANCE. DURABLE CONSTRUCTION.

DYNA-FLO LOW PRESSURE HYDRAULIC ACTUATORS: SCOTCH YOKE DRIVE MECHANISM. 1400+ IN/LBS OF SPRING END TPORQUE OUTPUT. SINGLE ACTING, SPRING RETURN OPERATION. 100 PSI LOW PRESSURE SUPPLY.* LOW TEMP RATED. POSITION INDICATOR INCLUDED. ISO 5211 MOUNTING COMPLIANCE

* DUE TO THE LOW PRESSURE SUPPLY, ACTUATOR SIZES ARE LIMITED BASED ON FLUID CAPACITY REQUIRED TO OPERATE . PLEASE CONSULT DYNA-FLO FOR INFO.

TYPICAL INSTALLATIONLOW PRESSURE UNIT INSTALLED IN HUSKY FIELD NEAR VERMILLION.

THIS APPLICATION USES TWO ESD’S IN TANDEM TO MEET REDUNDANCY REQUIREMENTS FOR PRESSURE PROTECTION.

ADAPTION HARDWARE:

DYNA-FLO DESIGNS AND MANUFACTURES ANY ADAPTION HARDWARE REQUIRED TO MOUNT ACTUATORS, PUMPS, & ACCESSORIES TO ANY VALVE OR ACTUATOR TYPE.

ALL MANUFACTURE IS DONE USING PRECISION CNC MACHINES WITH STRICT TOLERANCES, TO ENSURE A PERFECT FIT EVERY TIME.

PLEASE CONTACT DYNA-FLO FOR ALL YOUR HYDRAULIC ESD REQUIREMENTS, OR VISIT OUR WEB SITE WWW.DYNAFLO.COM