Embed Size (px)
Citation preview
JANUARY 2014
INSTALLATION GUIDE FOR THE KMW1031KT-DUAL
# Item Part Number Description
1 KMW1031 1-60-846-400 20 Watts RF Booster Amplifier
2 ANT1031 7-27-244-002 LOS Blade Antenna (TNC Male Connection)
3 TVP1031 7-57-001-004 KMW1031 Amplifier Pouch
4 TAH1031 7-57-002-001 LOS Blade Antenna Pouch
5 BC1031 4-68-538-101 Battery Cable 22”, 18 ga. wires, comes with mating connectors to battery and DC Input on amplifier.
6 RC1031 4-68-396-001 TNC Male to TNC Male (36” Long)
7 AC1031 4-68-562-002 TNC Male to TNC Female (36” Long)
8 RH-2535 7-27-317-001 SATCOM Antenna Mounting Head
9 RH-2535 7-27-317-001 SATCOM Blade Antenna (screw on mounting)
10 RH-2535 7-27-317-001 SATCOM Blade Antenna (screw on mounting)
11 RFS-117 7-16-221-001 Antenna RF Switch (RF Input, LOS and SATCOM Connection)
12 SSH1031 7-57-001-005 Antenna RF Switch Pouch
13 Cable Kit 4-68-603-036 BNC Male to TNC Female (36” Long)
14 Cable Kit 4-68-562-036 TNC Male to TNC Female (36” Long)***Note: this is an extra cable that is not used with the SATCOM configuration. The cable is needed if the user only wants to operate with a single LOS Antenna.
15 Cable Kit 4-68-602-036 BNC Male to BNC Male (36” Long)
1
2
3
45
6
7
9 10
8
1112
13
14
15
PARTS LIST KMW1031KT-DUAL
KMW1031KT-DUAL
Note to the Warfighter
Basic instructions on how to connect all the cables and accessories on the KMW1031KT-DUAL RF Booster Amplifier.
Configuration will be different on tactical vests and what is individually desired.
Step 1 Slide the KMW1031
into the TVP1031 pouch with the single DC connector on the bottom and the two RF connectors on top.
TVP1031(7-57-001-004)
Step 2 Connect the
battery cable BC1031 to the DC connector
BC 1031 (4-68-538-101)
Align with DC connector on the bottom and twist to connect
Connects with XX90 military style batteries
Step 3 Assemble the
RAMHEAD SATCOM Antenna
Comes in 3-pieces
RH-2535 (7-27-317-001)
Step 4 Screw in both
antenna blades It will not matter
which side the blade antenna goes into.
RH-2535 (7-27-317-001)
Step 5
Attach RAMHEAD antenna to the SATCOM cable and SATCOM/LOS Switch.
SATCOM port is on the “left” side of the switch.
RH-2535 (7-27-317-001)
RFS-117 (7-16-221-001)
SATCOM Cable(4-68-602-036)
Step 6 Assembling the
LOS Blade Antenna
LOS Antenna to Switch Cable (4-68-603-036)
ANT1031 (7-27-244-002)
TAH1031(7-57-002-001)
Step 7 Connect antenna to
the cable and then slide the open end through the antenna pouch.
Step 8 Thread through
until the bottom of the antenna is snug within the pouch.
Secure the Velcro strap on the neck of the antenna.
Step 9 Connect the
LOS antenna and cable to the “top” of the SATCOM/LOS switch.
Step 10 Connect the “L”
connector into the “OUT” port on the KMW1031.
AC1031 (4-68-562-002)
Step 11 Connect the
antenna cable to the “bottom” of the SATCOM/LOS switch.
Step 12 Fasten the
SATCOM/LOS Switch Holder with the Velcro straps from the “top” and “bottom” of the unit SSH1031 (7-57-001-
005)
Step 13 Connect the radio
cable Most hand held
radios are compatible with the KMW1031 Kit. Please contact AR Modular RF for more information.
Hand Held Radio
(Thales MBITR is not included with kit)
RC1031(4-68-396-001)
Step 14 Connect the
radio to the “IN” port on the KMW1031
(Thales MBITR is not included with kit)
CONGRATULATIONS! You’re done! Please consult the KMW1031KT-DUAL
Operator’s Manual on how to use the RF Amplifier properly.
Enjoy the enhanced communications!
Contact ListChris Heavens•VP & General Manager
Mike Katzer•General Sales Manager
•425.879.7482 mobile
Jim Wilcox•Regional Sales Manager
•206.245.0288 mobile
AR Modular RF21222 30th Drive SESuite 200Bothell, WA 98021425.485.9000www.arworld.us
Joe Reminder•Regional Sales Manager
•585.663.1027 mobile
Robert Kim• Inside Sales Engineer
Linda Martian-Trent•Sales Assistant• [email protected]
Thank You!
